About the wheel bolt pattern parameters on Hyundai

Hyundai Solaris is a passenger car from the South Korean concern Hyundai Motors. Solaris is made on a platform basis from Hyundai Accent. The model is of high quality, well built, adapted for domestic roads.

Since its debut, two generations of Hyundai Solaris have been released:

  • First: 2011-2017;
  • Second: 2022 – present.

In addition to two generations, intermediate restyled versions were released: 2011 - 2016. There are no fundamental differences between the modifications, but with some features that you need to know about.

Selection of disks

The manufacturer allows the use of disks of different sizes. This parameter may depend on the vehicle configuration. When choosing this design, first of all, pay attention to the material that was used to make the product:

  • Standard stamped steel cannot boast of an aesthetic appearance, but is famous for its durability and strength. This is an inexpensive option that suits many car enthusiasts. Can be supplemented with plastic caps.
  • Forged light alloy is an expensive option, characterized by a large margin of strength and an impressive appearance.
  • Light alloy cast can be both affordable and very expensive. The upper cost threshold is limited only by your budget. Such discs can have an unusual design and high strength.

When choosing a disk, you need to consider the following parameters:

  • landing width;
  • departure;
  • number of wheel bolts and spacing between them;
  • landing diameter.

This is interesting: How to find out the year of manufacture of a Bridgestone tire

Tire quality

In addition to the size of the rims, bolt pattern, type of tires and other things, there are still important points that you should pay attention to when choosing wheels. This is the quality of rubber for Hyundai Solaris. Of course, it is more difficult to determine it by appearance, but you can use information from manufacturers and benefit from the experience of other motorists. In general, tire quality will affect the following indicators:

  1. Braking efficiency;
  2. Controllability;
  3. Comfort when driving;
  4. The durability of the tires themselves.

At the factory, new cars are equipped with Kumho Solus or Hankook Optima tires. This is an inexpensive Korean-made tire that nevertheless meets modern requirements for road grip, durability and noise level. Such wheels can be safely installed after the factory set has worn out; their characteristics are sufficient for comfortable movement in city conditions. They have good ability to drain water when driving in wet weather, and also have good speed and weight indexes with a reserve for this car. On the highway, under normal conditions, in compliance with the permitted speed limits, they also do not cause any complaints.

Fans of dynamic driving with sharp accelerations and the same pressure on the brake pedal in difficult road situations may need wider rubber capabilities and improved performance. They should consider options like the Hankook Tire Optimo K406 88H (up to 210 km/h), Continental ContiPremiumContact 2, Dunlop SP Sport FastResponse 88V (up to 240 km/h) or something like that. These tires are significantly more expensive, but are much better suited for high speed loads and braking. Naturally, the choice of good wheels for Solaris is not limited to these brands; in this price segment there are a large number of excellent offers from various world-famous manufacturers, including Nokian, Bridgestone, Yokohama, Pirelli and others.

There are also less expensive options to refit your car, and they are quite suitable for those drivers whose priorities are not speed performance, but price and normal overall performance are more important. Examples of such tires include Dunlop SP Touring T1, Viatti Strada Assimetrico V-130, Cordiant Sport W1 for summer, Viatti Brina V-521, Cordiant Polar 2, Dunlop SP Winter Sport 400 and others for winter.

Features of the bolt pattern

If you do not want to install branded wheels on the Hyundai Solaris, then you need to focus on the bolt pattern for the R15:

  • 6 inches – landing width;
  • 48 – departure;
  • location of fasteners 4x100;
  • The landing dimensions of the central hole are 54.1 millimeters.

If, according to the documentation, you have R16 wheels installed, then only the offset value will change - 52. The remaining parameters are similar. It is not difficult to select disks to the described sizes; many manufacturers have suitable models.

Standard tire sizes for Solaris:

  • 185/65/R15;
  • 195/55/R16.

Sometimes manufacturers encode technical characteristics into codes. For example, you may come across this option: 4/112 ET48. It means that the wheel is secured with 4 bolts with a length of 112 millimeters, and the disc offset is 48.

When purchasing tires and wheels, do not try to save money. At best, an unsuitable wheel model will not fit on your car, and at worst, it will cause a lot of problems while driving. It is better to spend a little time to choose an option that is suitable for the bolt pattern than to later invest in car repairs, and possibly in your health.

Maximum and minimum possible parameters of non-standard disks

The rim width, offset and drilling for a non-standard disk must correspond to the factory values.

If the PCD value differs by millimeters, the wheel will not sit completely on the hub - one nut will be tightened well, and the rest will be either overtightened or undertightened. This is fraught with “beating” of the disk, and loosely tightened nuts can be unscrewed while moving. A reduced offset value will lead to overload of the suspension and hub bearings, and an increased value will result in the disc touching the elements of the vehicle’s braking system.

As for the hub diameter, it must be observed for stamped discs. You can install alloy wheels with a large DIA value on your car by using a special spacer ring made of metal or plastic.

But the diameter of the disk may be larger. Only as the wheel size increases should the tire profile decrease. Yes, with larger diameter wheels the speed will increase, the handling in corners will be better, and the ground clearance will be greater. But at the same time, the car will accelerate and brake more slowly, and there will be less driving comfort, since a thinner tire will absorb shock loads worse than that recommended by the manufacturer.

Standard wheel sizes for Hyundai Solaris 1.6i I

The Hyundai Solaris 1.6i I model was produced from 2011 to 2014. Table of standard and suitable wheel sizes for Hyundai Solaris 1.6i I.

Disc drilling parameters are usually called bolt pattern:

  • LZ (number of holes)
  • PCD (hole center circle diameter)
  • ET (disc offset)
  • DIA (hole diameter)
Make model modification AutoYear of issueOptionsDisc widthDisc diameterBolt pattern LZ*PCDDeparture ETDiameter DIAtype of instalation
Hyundai Solaris 1.6i I20145.5Jx14 4/100 ET43 d54.15.5144X1004354.1Factory
Hyundai Solaris 1.6i I6Jx15 4/100 ET48 d54.16154X1004854.1Acceptable
Hyundai Solaris 1.6i I6Jx16 4/100 ET52 d54.16164X1005254.1Acceptable
Hyundai Solaris 1.6i I6.5Jx16 4/100 ET43 d54.16.5164X1004354.1Acceptable
Hyundai Solaris 1.6i I6.5Jx17 4/100 ET43 d54.16.5174X1004354.1Acceptable
Hyundai Solaris 1.6i I20135.5Jx14 4/100 ET43 d54.15.5144X1004354.1Factory
Hyundai Solaris 1.6i I6Jx15 4/100 ET48 d54.16154X1004854.1Acceptable
Hyundai Solaris 1.6i I6Jx16 4/100 ET52 d54.16164X1005254.1Acceptable
Hyundai Solaris 1.6i I6.5Jx16 4/100 ET43 d54.16.5164X1004354.1Acceptable
Hyundai Solaris 1.6i I6.5Jx17 4/100 ET43 d54.16.5174X1004354.1Acceptable
Hyundai Solaris 1.6i I20125.5Jx14 4/100 ET43 d54.15.5144X1004354.1Factory
Hyundai Solaris 1.6i I6Jx15 4/100 ET48 d54.16154X1004854.1Acceptable
Hyundai Solaris 1.6i I6Jx16 4/100 ET52 d54.16164X1005254.1Acceptable
Hyundai Solaris 1.6i I6.5Jx16 4/100 ET43 d54.16.5164X1004354.1Acceptable
Hyundai Solaris 1.6i I6.5Jx17 4/100 ET43 d54.16.5174X1004354.1Acceptable
Hyundai Solaris 1.6i I20115.5Jx14 4/100 ET43 d54.15.5144X1004354.1Factory
Hyundai Solaris 1.6i I6Jx15 4/100 ET48 d54.16154X1004854.1Acceptable
Hyundai Solaris 1.6i I6Jx16 4/100 ET52 d54.16164X1005254.1Acceptable
Hyundai Solaris 1.6i I6.5Jx16 4/100 ET43 d54.16.5164X1004354.1Acceptable
Hyundai Solaris 1.6i I6.5Jx17 4/100 ET43 d54.16.5174X1004354.1Acceptable

How to choose wheels for Solaris

While you need to replace the wheels, you can take your time to get tires first; you will always have time to buy Toyo tires. The accuracy and compliance of wheel components will ensure reliable driving and help avoid premature wear.

The disks on the Hyundai Solaris are mounted on four bolts located along a 100 mm circumference (PCD), the mounting width of the disk can be 5.5 inches with a 15-inch diameter of the landing rim or 6 inches with both 15 and 16 inches of landing diameter, with disc offset in the range of 46-52 mm. When choosing the size of wheels for Solaris, first of all, focus on the engine modification and year of manufacture of your car.

Disk parameters on Solaris

ModificationYearDisk sizeDisc offsetBolt pattern
1.4 1.62010 20115.5x15464×100
6.0x1652
Gamma 1.4 Gamma 1.620106.0x1548
2011
2012
2013

To replace a Hyundai Solaris, we recommend buying Replica wheels that will exactly match all the parameters of this car.

The table below shows the most suitable models of this brand, which have a constant number of bolts (4 pieces), diameter of their centers (PCD=100 mm), hole diameter for the hub (DIA=54.1) and mounting diameter (15 inches).

Also, depending on the required landing width of the disk and its offset, you can choose your Replica for your Solaris.

Which wheels to choose for Solaris

Bolt patternCentering hole diameter (DIA), mmBore diameter, inchesSeating width, inchesReach (ET), mmModel Brand Replica
4×10054.1156.045LW HND72
48
  • RK L31F
  • HY60
  • FR5026 S
  • HND117
  • HND72
  • HND73
  • HND79
  • Ki104
  • Ki52
  • Ki57
  • Ki52
  • Ki62
5.546
  1. FR036
  2. FR753
  3. FR753

In addition to the Replica, KiK wheels fit well on the Hyundai Solaris with the same Pirelli tires. Models KC488 “Black Platinum” and KS582 “Black Diamond” will perfectly replace 6.0×15 wheels with a 54.1 mm hub hole and 48 mm offset, as well as KC445Silver with 39 mm ET and DIA56.6 mm.

Discs with a width of 5.5 and a diameter of 15 inches can be replaced with KS427 Silver with an offset of 48 mm and a centering hole diameter of 60.1 mm.

Source: https://pieman.ru/kak_vibratj_diski_na_solyaris

Answers (6)

Follow the answers to this question

  • The width of all wheels is 6J, offset is ET48 for R15 wheels and ET52 for R6, hub diameter is Dia 54.1 mm

    Airat Kadyrmaev I love cars, especially practical ones, my channel on...

    03/06/2018 at 13:56

  • Similar questions

    Alexander Kirillov

    Hyundai Solaris Lada Vesta

    Decoding disk markings

    For example, R17 4×100 5.5J ET46

    • PCD (Pitch Circle Diameter) diameter of the center circle of the mounting holes: 87 mm;
    • Disk radius at 17;
    • Drilling: number of holes 4;
    • Fastening type: M10 – stud diameter;
    • Thread size (pitch): 1.25;
    • Center hole diameter: 57 mm;
    • Pressure (front / rear): 2.0 / 2.1 bar.

    The PCD value is calculated by the distance between the centers of opposite holes. We measure with a ruler, but do not dismantle the wheel. For four bolt construction, the PCD corresponds to the actual distance.

    Rim offset is indicated by “ET”, the unit of measurement is millimeters. This is the distance between the point of contact between the disc and the hub and the middle of the rim width.

    In different countries the designation is different: DEPORT, OFFSET. The offset is positive if the plane does not extend beyond the point of contact, otherwise the offset is negative.

    The further the rim is from the body, the more the offset tends to zero.

    • D is the diameter of the central hole, measured in millimeters.
    • J, H and subsequent alphabetical symbols indicate the markings of the humps on the rim flange. Symmetrical, asymmetrical and combined.
    • The “Hump” is a protrusion on the rim for a tubeless tire. When moving, the “rails” hold the tire beads, preventing depressurization.

    Numerical characters indicate the release date, month, year.

    • TUV is an abbreviation for the regulatory authority for compliance with quality standards.

    Maximum wheel load: the unit of measurement depends on the country of manufacture of the rubber and rim.

    This is interesting: Why do you need wheel balancing?

    What is the effect of installing non-standard dimensions on the Hyundai Solaris?

    The size of wheels, tires, disks that are installed on a car have a direct impact on its technical characteristics. In the instruction manual, the manufacturer indicates recommended and acceptable sizes.

    The owner of a Hyundai Solaris independently decides what type and size of wheels and tires to install. For a driver who uses the car as a means of transportation, the factory rim sizes are more than enough.

    In case of tuning, changes in standard characteristics, dynamic indicators, it is necessary to refit the car with non-standard wheel sizes.

    List of characteristics that can be changed by installing non-standard wheel sizes:

    • Controllability;
    • Road grip;
    • Sharp and responsive steering wheel;
    • Reduced (increased) aquaplaning;
    • Comfort of movement;
    • Noise level;
    • Combined cycle fuel consumption;
    • Tread wear rate.

    Parameters of standard nuts

    Wheels for Hyundai Solaris cars produced between 2011 and 2022 were fastened with standard M12x1.5 nuts. The thread diameter of the nuts is 12 mm, and the thread pitch is 1.5 mm. Tightening torque – 88-107 Nm. Material – steel coated with chrome and zinc.

    The original stamped wheels have open-type cone nuts 34 mm long. For non-original casting, it is recommended to install nuts 34-40 mm long, since cast wheels are thicker than stamped ones. For this reason, it is better not to place nuts from stamped wheels on alloy wheels - the engagement of the threaded connection will be insufficient for their reliable fastening.

    Recommendations for disc care

    • Check the geometry and wheel balancing on a special diagnostic stand. If deviations are detected, restore the integrity of the structure at a service station. It is impossible to “reanimate” the disk on your own due to the lack of necessary equipment;
    • Immediately contact a service station for preventive maintenance if you find cracks or dents on the rim;
    • Avoid getting into potholes, especially at high and medium speeds. The disk will be deformed, the seal will be broken, regardless of the material of manufacture;
    • Monitor the tire pressure; it should not differ from that recommended by the manufacturer. If there is a deviation, pump it up yourself, contact the service station;
    • Observe the transition to summer and winter modes. In summer, the tire pressure is 0.15 atm higher, in winter it is lower by the same amount. The parameters are specified in the vehicle operating instructions;
    • Tighten the rim nuts with a torque wrench. Excessive tightening contributes to the breakage of the studs, weak - to the unscrewing of the wheel and a collision on the road.

    In sunny weather, cast aluminum wheels are least susceptible to external damage. But in slush, ice, when the road is strewn with various chemicals, the rim is susceptible to corrosion. This provokes paint peeling and destruction of the molecular composition.

    Wash your wheels as they get dirty. Since it is unlikely that you can clean it properly with a rag, use high-pressure compressors. Equipment of this class is available at many service stations, workshops, and service centers.

    Systematic polishing allows you to get rid of scratches and burrs. First clean the wheel from dirt, dry it thoroughly, and then treat it with a chemical. Wipe several times with a microfiber cloth.

    Store wheels in a hanging position, do not stack them on top of each other. Clean off any dirt, dry, and wrap in cellophane. Some motorists practice applying an aerosol to the surface before preservation. However, this is a purely personal decision of the owner.

    The average service life of original wheels is 150 – 180 thousand km. Subject to a moderate driving style, the replacement interval will increase by a third. The service life of tires is half as long as disks.

    How the pressure sensor works, how to turn it off

    Each tire manufacturer determines the pressure for tires individually, based on their technical indicators and characteristics. Exact data is always indicated in the vehicle's operating manual.

    NameAtmospheres (Bar)
    Front (summer)2.1
    Rear (summer)1.9
    Front when fully loaded2.4
    Rear at full load2.8
    Winter (front/rear)2.2 / 2.1

    Starting from the second generation, Hyundai Solaris is equipped with electronic tire pressure sensors. The first generation has mechanical sensors. Due to insufficient efficiency and information content, the latter were replaced by modern ones.

    The main task of the digital gadget is to monitor changes in air pressure in the tire and transmit data online to the electronic control unit. The latter compares the indicators with the programmed ones and informs the driver about a possible malfunction. Most often, this is a sound signal combined with light flickering.

    Tire pressure level is one of the most important indicators that determine the behavior of a car while driving on the road. Road traction and, in general, driving safety depend on tire pressure. Therefore, it is recommended to regularly measure tire pressure. The manufacturer recommends carrying out such a check simultaneously with refueling the vehicle. To do this, it is useful to keep a pressure gauge in the trunk. This way you can avoid rapid wear of the rubber.

    Recommended tire pressure for Hyundai Solaris: 2.2 Bar (or 32 psi) for rear and front wheels. In other words, about 2.2 atmospheres. For full load, the manufacturer recommends maintaining the same pressure. This data is indicated on a plate located in the driver's doorway or in the operating manual.

    Low tire pressure can lead to some unpleasant factors:

    • Fuel consumption increases;
    • Vehicle dynamics indicators decrease;
    • Car handling deteriorates.

    Tire pressure should only be measured when the tires are cold, otherwise the readings will be incorrect.

    Hyundai Solaris cars are equipped with a system for indirect measurement and monitoring of tire pressure. A sensor in the ABS system is responsible for this, which reads the wheel speed. The system monitors the difference in revolutions between wheels with a set rotation value.

    When descending, the wheel reduces its radius and therefore rotates a little faster. It turns out that in one revolution a good tire travels a greater distance than a flat one. The sensor signals are compared in the ABS unit with control values. The system notices a discrepancy in values ​​and reacts to this with an audible signal and an indicator on the dashboard.

    There are no pressure sensors installed in the wheels themselves, so you can change them without fear. However, after replacing the wheels or as a result of service work, the indicator may light up, even if the tire pressure is fine. How can I disable this error? In this case, you must turn on the ignition and press the sensor initialization button for 3 seconds. This will complete the setup of the sensors and you will be able to continue driving with the new rims without any problems. The sensor now works with the new parameters.

    Do you know which indicator is one of the main ones that determines the behavior of your car while driving on the road? This indicator plays a significant role in the effectiveness of adhesion to the road surface, which, in turn, directly affects the level of safety of movement. Ensuring the proper level of this indicator recommended by the car manufacturer is one of the most reliable options to avoid problems along the way.

    We are, of course, talking about tire pressure levels. And today we will get acquainted with information about this important indicator from the words of specialists.

    The level of tire pressure determines how the car behaves while driving on the road. Therefore it must be strictly controlled.

    Any deviations will have a negative impact on the efficiency of Hyundai Solaris’s traction with the road surface, which will reduce the level of driving safety. You can avoid troubles along the way if you follow the manufacturer's recommendations.

    They are indicated in the operating instructions or in the door arch where the driver sits. For Hyundai Solaris, 2.2 bar is optimal. The pressure value for the front and rear wheels is the same.

    It is recommended to carry out a similar procedure every day or once a week. This will prevent tire wear and save money. Below is a table that shows tire pressure depending on the type and size of wheels.

    It will be useful to owners of a Solaris car.

    It is necessary to monitor the pressure of car tires twice a month.

    This will significantly reduce carbon dioxide emissions, reduce fuel consumption and extend the life of the tires themselves. Don’t forget about comfort, which is not very pleasant when driving on overinflated tires.

    In the table below, we suggest you familiarize yourself with the recommended tire pressure for Hyundai cars.

    Tire pressure table for Hyundai car
    ModelMode StandardComfort modeSport mode
    frontrearfrontrearfrontrear
    Solaris2,22,22,02,02,82,8
    i302,12,11,92,02,72,7
    i402,42,42,22,22,82,8
    ix352,32,32,02,02,82,8
    Sonata2,22,22,12,12,82,8
    Santa Fe2,12,12,02,03,03,0

    More on the topic: How to choose wheels for Hyundai Solaris

    Pressure in Solaris

    The pressure in Hyundai Solaris cars is indicated on the door arch. It is recommended to pump Solaris tires at 2.2 bar, regardless of the tire size. Naturally, this is the pressure in cold tires, i.e. in a car that had been at rest for 30 minutes.

    If you measure the pressure in hot tires, it will be higher than recommended for Solaris. For economical mode, it is recommended to pump the tires to 2.8 bar; this will allow, albeit slightly, to save on fuel. Although, perhaps, to the detriment of saving on tires.

    What should the pressure be in Santa Fe?

    Santa Fe belongs to the class of small SUVs, so its tire pressure can vary significantly depending on operating conditions and the tires installed.

    The suspension on the Santa Fe is soft, so you need to keep the tires with low pressure only when necessary, for example, when we are driving on a muddy forest road or you need to reduce the pressure to lower the car's height by 2-5 cm.

    Winter tires for Hyundai Accent and Solaris 2011

    On a note.

    It must be said that any automobile concern always releases the next modification of the vehicle from the assembly line with tires already installed that are compatible with rims of the above dimensions.

    However, this wheel is most often a summer one, and when cold weather sets in, most Russian drivers, fearing deterioration in the controllability of their “iron horse,” traditionally search for and buy winter tires.

    Most car enthusiasts invariably purchase studded tires. This is not at all necessary when driving a car in the city, because the friction properties of the sharp lamellas of modern studless tires work even better than treads with metal pointed studs. For the most popular Hyundai models, the most popular are the following winter tire options, compatible with the wheel bolt pattern of the Hyundai Accent:

    • For the Accent model, the manufacturer installs tires with the following size parameters, depending on the model’s configuration.

    The most budget cars are equipped with tires with a size of 185/65/R15, which is convenient when driving in winter, because the high profile guarantees shock absorption due to the air buffer.

    It also provides additional traction on loose snow, not only under the treaded outsole, but also along the side of the wheel.

    Modifications in the mid-price category come off the assembly line with tires already installed on the wheels, having dimensions of 195/55/R16. Such characteristics are ideally suited for both winter and summer driving around the city or on less snowy roads outside the city. Drivers of such cars often use all-season tires for their “iron horses,” which saves them from periodically changing shoes twice a year.

    You might be interested in this About Alutec wheel rims for a car


    Tucson bolt pattern

    Top variants of the Accent have the same bolt pattern as the Getz and are equipped with tires with parameters 205/45/R17, which have a wide grip surface. At the same time, it has a too small profile, which complicates safe driving around the city in winter.

    On a note.

    Car enthusiasts should take into account that the speed and load indices for the Hyundai Accent must be at least 88N, that is, each tire in an inflated state must normally withstand a load of 560 kg and drive in this state at a maximum speed of at least 210 km/h for 30 minutes. The Hyundai Getz has the same characteristics, the wheel size of which allows drivers to install tires from this already quite outdated model of the Korean brand.

    • The analogue of the above model - Solaris - has very similar parameters, being, in fact, a classmate of the Accent, which is why its tires and parameters recommended by experts have almost the same characteristics.

    Unlike the previous model, the Solaris tire size starts at 175/70/R14. Together with 185/65/R15, as well as for the Accent, it is very convenient for use in winter.

    With a landing diameter of 16 inches, the model is equipped with two main dimensions - 195/50/R14 and 195/55/R14. Only the last of them is suitable for all-season tires due to its fairly high sidewall.


    Wheels for Elantra

    Other parameters, such as the maximum permissible tire size for premium equipment, as well as load and speed indicators, completely repeat the same characteristics for the Hyundai Accent.

    Important!

    Considering the full compatibility of Accent and Solaris in terms of matching wheelbase dimensions and all dimensional characteristics of wheel arches, the wheels and tires for these cars are interchangeable. The bolt pattern of the Hyundai Getz wheels, the size of the Solaris and Accent tires are identical, and drivers can always reinstall the wheels from one model to another if the need arises.

    The bolt pattern of the Hyundai Solaris, as well as other Hyundai cars, can be easily classified into groups by class, within which these parameters coincide in 90% of cases. This makes it possible for car enthusiasts to choose wheels both from an official dealer and at other specialized sales points, practically without noticing that they belong to a particular model of a given brand.

    General background information

    Ranges of possible values ​​for tires and wheels Hyundai Solaris 2012.

    Tires

    Diameter14″–17″
    Width (mm)175–205
    Profile (%)45–70
    The smallest size175/70 R14
    The biggest size205/45 R17

    Wheel disks

    Diameter14″–17″
    Width (inches)5.5–6.5
    Reach (mm)43–52
    Drills4×100
    Expert advice

    When choosing tires for a car, you must first follow the manufacturer's instructions. Ask yourself a few questions.

    • On what roads will the car be primarily used?
    • Do you need increased cross-country ability?
    • How much of the route will be city roads and how much will be highways?
    • Will the vehicle carry heavy loads?

    The answers to these and similar questions will help determine which tire parameters you need to pay special attention to.

    How to choose the right wheels for Hyundai Solaris 2012?
    • Stamped (economical price category) - made from a sheet of iron by stamping on a press.
    • Light alloy - manufactured by casting (more reliable than stamped ones).
    • Forged (the highest quality and more expensive than the previous ones) - made from light alloys by stamping at high temperatures.

    The choice depends on financial capabilities. However, it should be borne in mind that the quality of the road surface on which you have to drive every day must also be taken into account.

    So, if it gets into a hole, a stamped disk will bend and will not cause harm to the tire, but a forged or cast one can cut it. There is a possibility that the cast disc may burst or crack.

    It should also be noted that repairing “stamping” wheels is cheaper than repairing cast or forged wheels. But wheels with high-quality cast and forged disks kill the suspension less, because lighter and have more perfect geometry (better balanced).

    The same wheels may or may not rub with tires on the same car - wheel alignment adjustment will help here.

    What is the tire pressure?

    It is the driver's responsibility to constantly monitor tire pressure. This will avoid standard problems associated with vehicle operation. An abnormal pressure value often causes:

    • deterioration of management;
    • uneven tread wear.

    Often the car owner independently reduces the pressure in the wheels of his own vehicle. This reduces the load on the suspension, and the car “passes” various road irregularities an order of magnitude easier. But it is worth noting: a decrease in pressure even by 0.1 MPa leads to serious problems. The main ones include:

    • increased fuel consumption;
    • rapid wear of the outer tread segments;
    • the car becomes less maneuverable.

    Wheel looseness

    Different wheels have been used on Hyundai Solaris in different generations. Usually this information is indicated in the service book or technical documents of the car. Also, on each vehicle there is a sign that says which wheels and tires are suitable.

    Wheel bolt pattern of Hyundai Solaris.

    Characteristics

    Let's look at the wheel bolt pattern for the Hyundai Solaris according to the manufacturer's data by year of manufacture and generation:

    Year Disk size Disc offset Sverlovka Tire size
    2010 15×5.5 46 4×100 185/65R15
    16×6.0 52 4×100 195/55R16
    2011 15×5.5 46 4×100 185/65R15
    16×6.0 52 4×100 195/55R16
    2010 15×5.5 46 4×100 185/65R15
    16×6.0 52 4×100 195/55R16
    2011 15×5.5 46 4×100 185/65R15
    16×6.0 52 4×100 195/55R16
    2010 15×6.0 48 4×100 185/65R15
    2011 15×6.0 48 4×100 185/65R15
    2012 15×6.0 48 4×100 185/65R15
    2013 15×6.0 48 4×100 185/65R15
    2010 15×6.0 48 4×100 185/65R15
    2011 15×6.0 48 4×100 185/65R15
    2012 15×6.0 48 4×100 185/65R15
    2013 15×6.0 48 4×100 185/65R15

    Hyundai Solaris disk parameters:

    PCD 4×100 with diameter from 15 to 16, width from 5.5J to 6J, offset from 46 to 52. Similar parameters to Hyundai Solaris Sedan (RB) 1.6 CRDI 2022. Tire size from 15 to 16, width from 185 to 195 and profile from 55 to 65. Minimum tire size: 195/55R16, maximum: 185/65R15.

    Alloy wheel rim.

    Year Disk size Disc offset Sverlovka Tire size
    2010 15×6.0 48 4×100 185/65R15
    2011 15×6.0 48 4×100 185/65R15
    2012 15×6.0 48 4×100 185/65R15
    2013 15×6.0 48 4×100 185/65R15
    2014 15×6.0 48 4×100 185/65R15
    2015 15×6.0 48 4×100 185/65R15
    2016 15×6.0 48 4×100 185/65R15
    2017 15×6.0 48 4×100 185/65R15
    2018 15×6.0 48 4×100 185/65R15
    2010 15×6.0 48 4×100 185/65R15
    2011 15×6.0 48 4×100 185/65R15
    2012 15×6.0 48 4×100 185/65R15
    2013 15×6.0 48 4×100 185/65R15
    2014 15×6.0 48 4×100 185/65R15
    2015 15×6.0 48 4×100 185/65R15
    2016 15×6.0 48 4×100 185/65R15
    2017 15×6.0 48 4×100 185/65R15
    2018 15×6.0 48 4×100 185/65R15
    2010 15×6.0 48 4×100 185/65R15
    2011 15×6.0 48 4×100 185/65R15
    2012 15×6.0 48 4×100 185/65R15
    2013 15×6.0 48 4×100 185/65R15
    2014 15×6.0 48 4×100 185/65R15
    2015 15×6.0 48 4×100 185/65R15
    2016 15×6.0 48 4×100 185/65R15
    2017 15×6.0 48 4×100 185/65R15
    2018 15×6.0 48 4×100 185/65R15
    2011 15×6.0 48 4×100 185/65R15
    2012 15×6.0 48 4×100 185/65R15
    2013 15×6.0 48 4×100 185/65R15
    2014 15×6.0 48 4×100 185/65R15
    2015 15×6.0 48 4×100 185/65R15
    2016 15×6.0 48 4×100 185/65R15
    2017 15×6.0 48 4×100 185/65R15
    2018 15×6.0 48 4×100 185/65R15

    Hyundai Solaris Sedan (RB) wheel parameters:

    PCD 4×100 with a diameter of 15, a width of 6J, an offset of 48. Similar parameters to the Kia Rio III (UB) 1.4 CRDi 2022. Tire sizes from 15 to 15, width from 185 to 185 and profile from 65 to 65.

    What wheels were installed on different car bodies and configurations?

    ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline! Read more"

    Since its inception, the Hyundai Solaris has had two body styles - a sedan and a five-liter hatchback with 1.4 liter engines producing 106 hp. and 1.6 liters for 121 hp. From 2022, the sedan body type receives the HCR label, and the hatchback is no longer produced.

    The entire model range is divided into three groups - the first generation (2011-2014), restyling I (2014-2017) and restyling II (from 2017 to the present). Each subtype had its own standard size.

    Rating
    ( 1 rating, average 5 out of 5 )
    Did you like the article? Share with friends:
    For any suggestions regarding the site: [email protected]
    Для любых предложений по сайту: [email protected]