Instructions for operation and installation of the Scher Khan Magicar 6 alarm system: setting up the key fob and autostart, connection diagram and video about the car alarm

Scher-Khan Magicar 6 is a two-way alarm without autostart with a dynamic code.
It provides the owner with such standard functions as passive and silent arming, anti-burglary mode, two-stage disarming, and car search in the parking lot.

It also allows you to implement separate opening of the driver and passenger doors (so-called), support for engine operation (turbo timer), display of battery voltage and temperature in the elephant.

Specifications

Security system characteristics:

Control method - radio signal from key fobs with a frequency of 433.92 MHz (frequency error ±0.2%).
Multifunctional communicator with display, two-way communication mode and four control and configuration buttons.
The transmitter power in the control panel is not higher than 10 mW.
The printed circuit board of the main unit is made using SMD technology and is equipped with four Magicar relays with an operating current of up to 30 Amps. Two relays are designed to control door locks, one for external light signaling and one to control the trunk lock circuit.
Operating range is up to 1.5 km due to the use of FM modulation in the radio control channel.
The power supply range for the circuit of the main unit with the processor is from 9 to 18 V (optimally 12 V).
Current consumption in standby mode is up to 30 mA.
Overall dimensions of the block – 244*116*39 mm.
The weight of the device is no more than 0.27 kg.
Possibility of operation at ambient temperatures from minus 40 ºС to plus 85 ºС.
Sound alarm - using a siren. Current consumption is 2 A, sound duration is 0.5 minutes (one cycle).
Visual alarm - hazard warning lamps. Control is carried out on both sides through separate circuits (current 7.5 A). The alarm flashes for 30 seconds at a frequency of 1 Hz.

The system protects electrical circuits from overloads using several methods:

standard fuse links in the vehicle's mounting block;
burnout resistances located inside the block;
transistor protective assemblies;
to protect against voltage surges and radio interference, the unit contains varistors;
Diode protection is used against polarity reversal.

Main functions

The Magikar 6 system allows the owner to implement the following functions:

the use of two individual channels to enable and disable security;
the ability to program a code for access to the car interior without a key fob;
adjustable delay mode for interior lighting;
separate power outputs for door locks, trunk and alarm;
the ability to automatically turn on the security mode;
built-in write protection in the memory of the block of additional control panels (using a separate PIN code);
automatic restoration of security if not a single limit switch on the doors is triggered;
silent operation;
hidden security mode (differs in the alarm being sent only to the key fob);
built-in protection of the siren circuit against short circuit;
the ability to control additional devices via two channels;
customizable parameters for additional channels;
the ability to use security functions when the power unit is running;
turbo timer (ignition shutdown delay for two minutes);
automatic opening and closing of locks when the ignition is turned off and on, respectively;
possibility of two-stage door unlocking with driver's priority;
the system allows you to open the trunk lock separately, keeping other zones under protection;
the ability to measure temperature parameters in the cabin using a separate sensor.

Review of the Scher Khan Magicar 6 car alarm provided by the Arnage Shop channel.

Equipment

Overview of the elements included in the signaling package:

technical user manual for installation, which provides all the diagrams for connecting the components;
service documentation for maintenance, allowing you to correctly configure the system;
microprocessor device;
main pager equipped with a screen;
additional communicator without display;
shock controller with CN5 wire;
sensor calling the car owner from inside the vehicle;
antenna adapter equipped with a connection cable;
power unit blocking relay;
temperature controller;
siren;
limit switch for mounting on the hood or tailgate;
a set of connectors intended for connecting an alarm system;
mounting set of wires;
three stickers - for connecting the call sensor, antenna adapter, as well as information - for the windshield.

A special feature of the Sherkhan Magikar 6 package is that it includes only one limit switch; devices for each door must be purchased separately.

Photo gallery

Photo of this model of anti-theft installation:

Security system equipment

Microprocessor alarm module

Control panels Sherkhan Magikar 6

Advantages and disadvantages

Based on user reviews, we can highlight the positive and negative aspects of using the Scher Khan Magicar 6 “signaling system”.

Positive aspects:

acceptable degree of protection;
color LCD screen with clear icon layout;
ease of operation and setup;
the ability to configure using a computer with pre-installed proprietary software and a programmer;
large range of operation of the system and key fobs;
sensitive sensors;
the ability to call the owner to the car;
control via an additional channel of microwave cabin volume sensors;
control of external lights and power windows (via an additional channel);
the ability to open the car without a key fob (via a call sensor).

There are many negative points noted:

low contrast due to the use of a dark substrate on the liquid crystal display (with the backlight turned off);
fragile and thin body of key fobs (especially communication ones);
requires the purchase of a programmer for configuration via a computer;
high power consumption by the key fob in hands-free mode (compensated by using a rechargeable battery with a capacity of 1000 mAh as a battery);
installation difficulties, for example, a separate connection of the engine starting system;
volatile memory (resets when power is turned off);
the owner's call sensor is unstable, especially at temperatures below minus 20 ºС;
due to the high sensitivity of the shock sensor, it is difficult to determine the threshold value of the warning response;
decreased range of action in dense urban areas;
there are problem specimens with defective components (sometimes defects appear over time);
the ability to scan and decipher the control code;
there is no activation of the blocking of the engine starting and power supply circuits when the hood lock is broken;
desynchronization of key fobs and the main unit (corrected by pressing the first button 35-40 times next to the car);
To protect engine circuits, the system has only analog circuits, so it is recommended to use a standard immobilizer;
failure of the key fob, which disables the two-way operation mode.

Disadvantages of car alarms

Disadvantages characteristic of this system:

the keychain is equipped with a fragile case that can fail even after a slight fall;
if the alarm setting is performed using a computer, then the user must additionally purchase a programmer;
Connection of an additional engine autostart module may cause difficulty;
when the power in the on-board network is turned off, the non-volatile alarm memory is reset to zero and the parameters are reset;
unstable operation of touch controllers at low negative temperatures;
difficulty in determining the threshold level of a warning signal;
when operating the alarm system in urban conditions, the range of the system will be lower;
a professional hijacker, using specialized equipment, can scan and decrypt the system control code;
spontaneous desynchronization of the microprocessor module and remote controls is eliminated by re-binding the devices;
The power unit is protected using analog electrical circuits, so the consumer should use a standard engine blocker.

Installation Rules

The Scher Khan Magicar 6 alarm system is not difficult to install and configure, so car owners carry out the installation themselves.

During installation, you must follow the basic rules for installing security systems on cars:

study the operating manual in detail;
think over the installation scheme;
use for installation of wires with an appearance as close as possible to standard wiring harnesses;
ensure insulation of wires at the place of twists using electrical tape or heat-shrinkable tubes;
when installing harnesses for controlling actuators on moving body elements, protective tubes should be used;
do not allow kinks in the wiring or pinching by interior trim elements;
Do not bend wiring harnesses through metal body panels with sharp edges;
to route wiring into the engine compartment or trunk, use standard channels or separate bushings that protect the cables from chafing;
to extend the wiring, it is allowed to use a product of a similar or larger cross-section;
It is prohibited to use wires with aluminum or steel conductors;
The installation sites of system elements must exclude the possibility of flooding with process liquids or water;
It is recommended to place electrical connectors down or to the side, which will prevent condensation from accumulating;
wiring harnesses should have slight slack;
Alarm components should not be located near heat sources (exhaust manifold, air conditioner ducts, radiator);
when placing elements and wiring harnesses, it is necessary to check that there are no interferences with moving mechanisms (steering column shaft, pedals, rods);
The free play of the limit switch drives must be at least 5 mm (to reduce the likelihood of false alarms).

How to install?

Installation procedure:

Disconnect the battery from the vehicle's on-board circuit.
Remove the protective covers on the instrument panel and pillar trims (in accordance with the intended installation diagram).
Place the processor unit in the instrument panel at a short distance from the main wiring harnesses. Since the device is equipped with vibration-sensitive electronic components, it must be rigidly attached to the body or instrument panel frame. Plastic ties or double-sided tape are used for fixation. The manufacturer does not recommend installing the device in the engine compartment, as well as on standard electronic units or in close proximity to them.
Install the antenna on the windshield in a vertical position (to ensure maximum communication range). Most installers mount the device in the top corners of the glass, at least 5cm away from the metal body panels. It is permissible to install the antenna on the side fixed windows (rigidly installed in the body), sun visors, the surface of the rear window or the shelf underneath it. The unit is installed using double-sided tape at an air temperature of at least plus 10 ºС. To ensure reliable contact, it is recommended to degrease the installation site with alcohol or gasoline for lighters.
Route the wiring harness from the antenna to the unit through the channels in the A-pillars.
Place the owner call sensor on the windshield. The usual installation location is the bottom corners of the glass. The process of installing the sensor is similar to installing an antenna. The sensor body should not come into contact with body parts or plastic trim, as this increases the likelihood of false alarms. To adjust the sensor, there is a regulator with three fixed settings, indicated on the body by pictograms in the form of circles. The minimum level of sensitivity corresponds to a circle of small diameter, the maximum - to a large one.
Place and secure the siren on the engine compartment mudguard or engine shield. When choosing a location, it is necessary to ensure that the device is protected from access from below (through the wheel arch or power unit protection screens). The horn should point downwards. When using an autonomous siren, quick and unhindered access to the control lock (used for shutdown) must be provided. Negative power is supplied from the car body (through a ground bolt or nut).
Connect the siren wiring harness and lead it to the alarm unit.
Install the end caps of the hood and trunk lids. The installation locations of the devices must have good contact with the surface of the body. The optimal places are areas that are protected by rubber seals. It is strictly prohibited to place limit switches in drainage channels.
Lay the wires from the end switches to the main unit.
Install a shock sensor in the cabin, which is attached with screws or double-sided tape. It is not recommended to place the device on plastic trim elements that are not rigidly attached to the body. The owner must have unhindered access to the sensor to configure it during operation.
Install an additional sensor, if included in the kit or purchased separately.
Connect ground power to the black wire from connector CN1 (main harness). The connection is made to the ground nuts on the body or directly to the battery terminal using a copper wire with a cross-section of 6-8 mm2.
Connect the red wire from the connector to the positive power supply. It is possible to connect directly to the battery or by inserting a wire into the ignition switch circuit. The selected cable must provide voltage supply in any operating mode. The connection must be soldered and reliably insulated.
Connect the remaining six wires of the CN1 connector to the trunk lock relay, the lock itself, the siren, and the hazard warning lights.
Engage the wires of the CN2 connector, which controls the operation of the door locks. Connection diagrams are shown below. Connect the ten wires of the CN3 block. When connecting the harness to standard hood or trunk opening sensors, it may be necessary to install a diode decoupler. It is used in the operation of trunk lighting only when the side lights are functioning and consists of four diodes of type 1N4007 or similar Russian KD243A. The block contains wires (with orange and black insulation) that are responsible for warning about the lights not being turned off. The cables are activated at the request of the owner or installer.
Connect the temperature sensor to the CN4 block and place it at a distance from the air conditioner ducts.
Begin connecting the remaining wiring harnesses to the unit connectors.
Connect block CN5 with wiring from the shock sensor and cable CN6 from the call sensor.
Connect the antenna harness connector CN7.
When installing an additional relay, it is connected to block CN8.
The additional sensor harness is connected to the CN9 block.
Secure the wiring harnesses with zip ties.
Reinstall the removed trims and connect the battery.
Teach the processor unit the control panel code.
Configure system operating parameters.

Photo gallery “Harness connection diagrams”

Connecting the trunk lock drive

The first option for wiring the CN2 harness

Second option for wiring the CN2 harness

The third option for wiring the CN2 harness

The fourth option for wiring the CN2 harness

Fifth option for wiring the CN2 harness

Sixth option for wiring harness CN2 Trunk lighting circuits with additional diodes

Interior light control (first option)

Interior light control (second option) Interior light control (third option)

Light control via additional relay

What to consider when connecting sensors

When installing or operating the Magikar 6 system, you should pay attention to the type of two-level shock sensor.

There are two sensor options:

With proportional sensitivity adjustment. It has one regulator and a scale marked from the Off position to the value 10. When adjusting the sensitivity, both zones are automatically adjusted, while the alarm signal is 30% higher than the warning signal. Due to its design, the sensor should only be installed on hard surfaces (steel body panels).
With separate zone regulation. Equipped with two regulators, each of which serves its own zone. Warning – adjusted with a potentiometer marked “1st”. The adjustment zone is indicated by extreme points with the “Min” and “Max” icons. For the alarm zone, a second potentiometer (“2st”) with a similar adjustment scale is used. When setting values, you cannot specify an alarm threshold lower than the warning threshold. The sensor has greater freedom of adjustment than the proportional one and is less demanding on installation rigidity.

Features of connecting an autonomous siren

In the case of using an autonomous siren, it is necessary to take into account the design and connection features:

Connect the brown insulated wire from the CN1 harness to the positive siren trigger.
The negative trigger is isolated and is not used in the connection.
Apply positive power to the siren through the main unit wire or directly from the battery through an additional 5 Amp insert.
Negative power to the siren is supplied from the nearest ground nut.

How to program the key fob?

The key fob and battery for the Scher Khan Magicar 6 alarm are supplied in an open state to ensure safety.

Key fob activation

To turn on the remote control you must:

Remove the cover retaining clip.
Pull out the cover.
Remove the battery and remove the polyethylene protective layer.
Install the element in its original place, observing the polarity. The negative terminal of the battery should be directed towards the antenna output on the key fob.
Close the lid and fasten the latch.

An overview of the Sherkhan Magikar 6 alarm system is presented in the video from the 220 Volt channel.

Programming

For programming you will need:

Disable security mode and deactivate the hands-free function on the key fob.
Turn the ignition on and off three times (in 4 seconds). If the owner has met the parameters, the car will flash the emergency lights once.
Within a period of no more than 4 seconds after the light signal, turn on the ignition. The number of activations corresponds to the first digit of the alarm code value (factory parameter 1).
After a single flash of the emergency lights, you can enter the second digit (factory value 1). The time interval between entering the first and second digits should not exceed 4 seconds. There will be another flash of the emergency lights, which signals that the system is ready to record key fobs.
Within four seconds, briefly press the system power button on the programmable remote control.
At intervals of up to four seconds, codes for other devices are written in the same way. If it is necessary to encode only one remote control, the button is pressed three times for a short time.
After recording the last key fob, wait another four seconds. The emergency lights should sound twice, confirming exit from the programming mode.

Sherkhan Magikar 6 has a memory designed for the use of three control panels. When registering a fourth remote control, the first one will be deleted from memory.

Advantages of the system

Advantages of the Sherkhan Magikar 6 alarm system:

reliable car protection: hacking the system with a code grabber is problematic;
the presence of a color screen on the remote control with all icons indicating simplifies system setup;
The package includes a service manual that allows you to independently install the alarm system;
the presence of sensitive sensors;
wide range of communicators;
the presence of a function to call the car owner from inside the vehicle;
the ability to change alarm parameters using a computer;
the presence of an option to configure autorun without a communicator.

User manual

Before making settings, you must study the alarm operating instructions.

Setting modes

The communicator can be used to configure parameters:

Disable security mode and hands-free mode.
By pressing the buttons you can enter the settings menu, which consists of two parts. The first one is accessed by pressing KI and KII (simultaneously for at least two seconds). Enabling the second part of the menu is done by similarly pressing KI and KIV. Confirmation of entry is the flashing of the alarm and the sound of the siren.
The function is selected using the KIV button. In this case, the number of clicks corresponds to the serial number of the option. With each press, the emergency lights should flash and the siren should sound.
After selecting the desired function, wait a few seconds. The siren and emergency lights should turn on, the number of alarms is equal to the option number.
The function value is selected using all buttons in accordance with the recommendations of the programming table. Confirmation of the choice is the flashing of the emergency lights and the sound of the siren, and the number of operations corresponds to the button number.

After setting each function of the Scher Khan Magicar 6, the system automatically exits the programming mode. The exit signal is a long siren sound. To configure the next option, you need to repeat steps from the first.

Identification of buttons on the communicator

Changing your PIN

By default, the block contains code 1111, which is recommended to be changed to your own value (in the range from 1111 to 4444):

Turn on the ignition when security is disarmed.
Press buttons KII and KIV simultaneously for a few seconds. The signal and emergency lights will sound. If a triple signal is given, this is an error notification when entering the settings.
Enter the first digit by short pressing the KI button on the remote control (within four seconds). Entering a number is confirmed by a siren and light alarm (the number of alarms corresponds to the number).
The remaining three digits are entered using a similar scheme (using the KII, KIII and KIV buttons, respectively).
Exit from the mode occurs automatically after programming the last digit and is confirmed by the double operation of the emergency lights and siren.

Deactivating the system with a PIN code

In the event of a breakdown or loss of communication with the control panels, you can deactivate the system with the code:

Disable the lock using the standard key and open the door. The system will turn on the alarm mode.
The owner has four seconds during which he must insert the key into the lock and turn the ignition on/off three times. After the third switch-off, the siren is deactivated.
After this, you need to quickly (within 4 seconds) enter the value of the first digit by switching the key in the lock from the Off position to the On position. The number of turns corresponds to the value of the number.
Wait for one flash of the emergency lights and enter the second digit.
Enter the third and fourth digits in the same way. After entering the last digit, the hazard lights will blink twice.
If the entered password matches the one stored in memory, the engine circuit blocking will be disabled and the Valet mode will be activated. If the code is entered incorrectly, the alarm mode will turn on.

Autostart

To implement the possibility of automatically starting the engine on the Sherkhan 6 alarm system, the installation of separate control modules is required. The unit will activate and turn off the engine based on signals from the additional channel, but notifications will not be sent to the key fob.

The only means of ensuring engine operation without a key is a turbo timer. To enable this mode, it is necessary to program the operation of the second additional channel. Engine operation will be extended with doors and covers closed for two minutes after the owner turns off the ignition. When the mode is active, the word “Turbo” lights up on the key fob. It is not recommended to use it due to the low resistance of the system to signal interception.

Device Features

It is possible to connect an additional sensor, for example, a microwave sensor (the so-called volume sensor). The main key fob is equipped with an informative LCD screen and a monolithic, damage-resistant antenna. There is a function to automatically turn on the display backlight.

During the theft of a car, the anti-robber system is activated, which immobilizes it. Support for external autorun module is provided by a universal function.

Car alarms for vehicles are made from high-quality raw materials, which guarantees them wear resistance and durability. The operating instructions will tell you more about this.

If the car is in security mode, its engine can be started from a distance using the control panel. The vehicle doors are unlocked from a distance in two steps thanks to the special hands-free function.

If the need arises, you can change the sensitivity of the sensors using the key fob. Using the universal hands-free function of this equipment, it is possible to digitally control the pre-start relay. You can register the hands-free function using the installation manual.

The car alarm disables sensors by zone in automatic mode. This is ensured by the hands-free function. The device has a modern encryption code, which ensures reliable protection of the vehicle. The system has a universal program, which allows you to use it to control the vehicle’s on-board network. The equipment key fob provides information about the temperature inside the vehicle. The device is characterized by the presence of two key fobs, which ensures comfortable operation. More detailed information is contained in the instruction manual.

Why does the alarm not work and how to fix it?

The Sherkhan 6 system is not a reliable device, and owners often encounter problems:

When you try to turn the security mode off or on, the system does not work. There is no communication indication on the screen, although the distance to the car does not exceed 1-2 meters. The indicator LED lights up in constant blue. This problem occurs when the setup mode is turned on spontaneously due to software glitches. To repair, you must deactivate the mode in accordance with the instructions. The second solution to the problem is to turn off the power to the on-board network and reconnect the antenna harness. If the alarm does not work normally, you will have to replace the system.
After activating the setup mode, the connection with the key fobs was lost. The locks only work with the standard key. Rebooting the unit according to the scheme described above can help.
The alarm operates normally, but the diode lights up red. The cause of the malfunction is failure or liquid ingress into the call sensor connector. You should remove the sensor, dry the contacts and install it back. If the procedure does not lead to a return to functionality, the sensor must be replaced with a new one.
Key fob failure after falling. The design is fragile and damage to the quartz may occur upon impact. Repairing the device or replacing it with a new one will help.
The alarm stops responding to all or part of the remote control buttons. A common problem with Sherkhan 6 is the loss of the control panel code, especially when the voltage in the on-board network is low or the car is “lit.” To repair, all key fobs must be reprogrammed.
Spontaneous activation of the call sensor (in various operating modes) together with loss of communication with the key fob. If such symptoms appear, it is recommended to replace the system.
The turn signals do not work when turned on or off. The cause of the problem is a failed fuse on the control circuit (wire with red and white insulation).
The alarm does not always lock the doors. The reason lies in damage to the lock control wiring harnesses.

If there is a frequent spontaneous transition to Valet mode or decoupling of the Sherkhan Magikar 6 alarm key fobs, it is recommended to replace the system with a more reliable one that is resistant to code grabbers.