Instructions for programming alarm key fobs Sherkhan Magikar

The breakdown has nothing to do with the car. So in January, button II (responsible for opening) on ​​my main alarm key fob failed. When I took it apart I saw that the microphone had broken off from the board:

I ordered a new one from Ali for 1054 rubles, in Tomsk there are 1500-1700 rubles. Last week a new keychain arrived from China:

Then I got my hands on the key fob, but I can’t link it to the alarm. I found information specifically about Sherkhan 5: PROGRAMMING NEW KEY FOBS The system can remember the codes of three key fobs. Follow two steps to program new key fobs. Turn the ignition key three times from the OFF to the ON position. The alarm will flash once to confirm entry into programming mode. No later than 4 sec. after the alarm flashes, press button I of the key fob, the code of which must be entered into the memory of the processor unit. To exit programming mode, do not take any action for 4 seconds. after recording the code of the last key fob. If after step 1 you do not take any action, then after 4 seconds. the alarm will flash 2 times, the system will switch from key fob programming mode to VALET mode. Note: the system has three memory cells for storing key fob codes. When you try to record the fourth key fob, the code of the first recorded key fob will be deleted.

As I understand it, there is no separate valet button on the 5 Sherkhan, turning the key three times as written above does not give anything. I found the whitefish itself under the tidy, when I soldered the Led pin, I removed it.

Most likely some kind of handyman installed the alarm, everything there is twisted. It looks like you need to look for a diagram, see what you screwed where.

Programming the Sherkhan 5 key fob may be needed in the following cases:

  1. The alarm does not turn on or off from one remote control, others work fine.
  2. Damage to the switch housing or circuit board.
  3. Incorrect operation of the main unit and remote control.
  4. Use of additional key fobs.

Three pagers can be stored in the anti-theft system's memory. This is not difficult to do, but the procedure has its own characteristics.

Linking a new key fob to the Scher Khan Magicar 5 alarm system

The instruction manual will help you to record a new communicator into the memory of Magikar 5. Please read it carefully before performing any operations with the remote control.

You can program the anti-theft system key fob only when the security mode is disabled. If you connect new remote controls, do not forget to overwrite the old ones, otherwise they will be deleted from the system memory.

  1. In four seconds. turn the ignition on and off three times. The lights will flash once. The programming mode has been entered.
  2. Enter the remote control code by pressing button 1. This must be done within four seconds. The vehicle's lights will light up once.
  3. If necessary, record the following switches in the same way.
  4. Do nothing for four seconds after programming the last remote and the system will automatically exit settings.

Malfunctions

The most common problem is sensor failure. This most often happens with devices located in the doors. Usually the cause is broken wires. Because of this, the alarm control unit detects the door as unlocked and begins to “voice.” You can identify the problem by the indicator on the remote control display. Inspect the wiring to the sensor in that door and replace the wire if necessary.

“Valet” mode may also be enabled

. In this case, it will be impossible to start the car. You need to try to disable the mode in the usual way. If it doesn’t work, you’ll have to change the entire signaling system.

Sometimes you can observe a complete reluctance of the alarm to work from the key fob. If the display does not light up or the low battery indicator is flashing, then most likely the problem is a low battery

. It needs to be replaced with a new one. The key fob settings may also be lost. In this case, you will have to reprogram it. To do this, it is better to contact specialists. They will be able to properly “train” the remote control. A more rare failure is the failure of the key fob antenna.

It is caused by displacement of the quartz element. It manifests itself as the inability to carry out any actions with the alarm using the remote control. If you have a second key fob, then simply check the operation of the alarm with it. If everything works, then the reason is the antenna. It is more difficult to check if there is no second remote control. In this case, you will have to call a technician from the service center. He will use special instruments to check the operation of the key fob.

If the alarm does not turn on at all, then it is likely due to lack of power. Check the wires

, supplying current to the alarm unit. It is likely that one of them is damaged. In this case, you can fix the problem yourself. Another sign of the same problem is a constantly running siren. This is due to the anti-theft protection against being turned off. When the terminals are removed from the battery, the protective mode is activated and the siren turns on. If the wires powering the unit break, it perceives the incident as an attempt at theft and turns on the siren.

Firmware and reprogramming Sherkhan 5

You can reflash the Magikar key fob version 5 using the PIN code. Record the remote control codes by following the instructions below.

  1. In four seconds, turn the ignition key three times from the “Off” to “On” position. Turn off the ignition.
  2. Turn the ignition back on within four seconds. The number of activations must match the first value of the secret code. The light optics will light up once, confirming that the second value can be entered.
  3. Turn on the ignition. The number of activations must correspond to the second digit of the code. The emergency light will blink once, confirming correct action.
  4. Enter the remaining secret number values ​​in the same way.
  5. After entering all the numbers, press button 1 of the switch. The lights will light up once to confirm the pager entry. After four seconds, the system will exit programming mode.

The additional Magicar 5 key fob is not registered: reasons

There are often situations with the anti-theft system communicator when it is not programmed. There are a number of reasons for this:

  • the remote control is damaged;
  • “Valet” mode is activated;
  • The system does not recognize the “Ignition on” command.

If you are unable to register the key fob on your own after trying all the options, you should replace it with a new one or contact the service src=”https://daciaclubmd.ru/wp-content/uploads/2018/12/peyterka-2.jpg” class =”aligncenter” width=”600″ height=”320″[/img]

Autorun setup instructions

Starting the engine is a very convenient function of the security system. After carefully studying the instruction manual, every car enthusiast can start the car using the key fob. Before programming, disarm the car, turn off the ignition, turn off the hands-free mode, and open one door just in case.

Time setting.

  1. To enter programming, simultaneously hold down keys 1 and 2.
  2. Enter the timed autorun settings by pressing button 4 thirteen times. After each press, the system should emit a single beep.
  3. Select the desired autostart time: button 2–8 hours, 3–4 hours, 4–2 hours.
  4. Then turn on the timer by clicking keys 2 and 4 simultaneously. The “timer” symbol will appear on the display.

Automatic engine start based on temperature.

  1. Enter programming mode: buttons 1 and 2.
  2. Press key 4 twenty-one times.
  3. Select the required temperature: key 2 – (-15), 3 – (-25), 4 – (+60).
  4. Turn on the timer by pressing 2 and 4 simultaneously. The display will show “timer”.

Protect yourself from robbery

When using the alarm models listed here, the owner will be able to increase the level of privacy used by the system. You can activate two-step disarming: pressing the “1” key leads to arming, while to disarm it you need to know the code. The PIN code is entered by pressing keys, typing two or four digits in succession. The option in question is also provided in the Scher Khan Logicar 3 systems produced in recent years. And the text below is taken from the instructions for the “Magikar” signaling device.

How to activate two-step protection

By default, the Scher Khan Magicar 3 system does not use two-step disarming. To use this option, activate it:

  1. Disarm the car, turn off the ignition, turn off the “Hands-free” mode (see above);
  2. Press buttons “1” and “4”, hold them for 2 seconds;
  3. A short signal from the “dimensions” and a siren will follow;
  4. Press the "4" button 6 times;
  5. Wait 4-5 seconds, 6 signals will follow;
  6. To use a 4-digit code during operation, press the “2” key, and if you need a two-digit code, press the “3” key;
  7. Two or three signals will follow.

The entire sequence above will need to be repeated. In the fourth step, you will press the key not 6, but 9 times. In the sixth step, press the “2” button, thereby activating the protection. It remains to change the code value, which by default is “1111”.

Table of programmable options, "Magikar"

The instruction manual supplied with the Magikar systems contains several links to a page where one control sequence is given. Performing the actions specified in it will allow you to change the code:

  1. Disarm the car, turn off the ignition;
  2. Press buttons “3” and “4”, hold them for 2 seconds;
  3. A single signal should follow;
  4. Press the key fob corresponding to the first digit;
  5. After you hear the confirmation beeps, repeat Step 4 for the remaining numbers.

Setting the secret code in Scher Khan Logicar 3 systems is performed in the same way: you need to open the door, turn on the ignition and go to “step 2” indicated in the list below. The top list is suitable for Logicar without changes, but option numbered “6” is replaced there by “option 8”:

Programmable Options Table, Logicar

This means that in step “4” you will press the button not 6, but 8 times.

Let's say option “6” or “8” is in the “factory” value, and two-step protection is activated. Then, in order to disarm the car during operation, the “2” key must be pressed twice.

Disarming without a key fob

Modern equipment is equipped with a Valet button, the presence of which will allow you to disable the security mode when the key fob is lost. For the Scher Khan Magicar 3 signaling, everything looks simpler: within 4 seconds, turn the ignition on and off three times, and the system activates the “Valet” mode. If you have a key fob, then press the “1-3” keys, which will disable the “Valet” mode and disarm the car.

Marks on the ignition switches

Cars protected by a Scher Khan Logicar 3 alarm system are no more difficult to disarm: turn on the ignition, press the Valet button, first for a long time, then briefly. But if you set a PIN code, the system will not allow you to disable the security until it receives the correct value. This is also true for the Magikar family of signals. The instructions for them say the following:

  1. If option "6" is set to "2" or "3", first perform the steps required to disarm without using a code;
  2. After the “dimensions” flash, turn the key to dial the value of the first digit;
  3. Repeat “step 2” to enter the second digit;
  4. If the code was four-digit, enter each digit by analogy with “step 2”.

As a result, the system will switch to “Valet” mode, in which you can drive the car, use the central locking, etc.

Whatever alarm you use, always set a secret code. It is enough to enable option “6”, set the required value, and the car will receive additional protection. For Scher Khan Logicar 3 systems, use option “8”. By the way, even a two-digit code has 16 options. No one will go through them.

How to remove Valet mode without a key fob

On the Sherkhan alarm system, it is quite easy to turn on the “Valet” mode by accidentally pressing it. Very often this is mistaken for a system failure: the alarm does not respond to blows, autostart fails, key fobs are not programmed, the LED is constantly on. Only the central locking and trunk opening work.

To disable Valet without a key fob, use the multifunction button located in a visible place.

  1. Turn on the ignition, do not start the engine.
  2. Press and hold the multifunction key for two seconds. "Jack" is disabled.

Equipment

The Sherkhan Magikar 9 alarm system comes complete with the following products:

  • instruction manual and warranty card;
  • head unit equipped with a microprocessor;
  • main key fob with liquid crystal display and feedback function;
  • spare communicator without display and two-way communication;
  • shock and tilt sensor with wire and terminal for connection;
  • button to call the user to the car;
  • antenna module;
  • engine temperature sensor;
  • siren;
  • power unit blocker with cable and connector;
  • limit switches installed on the trunk or hood;
  • a set of installation cables with 6-pin terminals and fuses;
  • wiring for connecting the antenna unit;
  • electrical circuit for introducing new modules;
  • four-core cable designed for integration into digital buses;
  • a set of stickers for mounting system elements.

Are all Sherkhan Magikar 5 keychains interchangeable?

The alarm remote control is something that is constantly lost, forgotten, broken, or falls into the water. It is not possible to connect a second key fob due to its absence. Replacing with the original remote control is also unrealistic. You have to look for a communicator from a family that is more or less compatible with yours. The pager may be completely, partially, or not suitable at all. We reviewed the compatibility of key fobs for the Sherkhan Magikar 5 anti-theft system earlier.

Photo gallery

Photos of some models of Sherkhan Magikar keychains and the location of the keys on them are presented in the gallery.


Remote control keys of the Magikar 6 system


Keychains of the security complex Sherkhan 7/9


Key fob buttons Magikar 13

Meaning of icons

Before you start programming the Sherkhan key fob, you need to find out what the icons on the display mean and what they are intended for. Key icons on the screen are used for the following notifications:

  1. Indication of the functionality of the communicator transmitter.
  2. Indication of the current battery charge level.
  3. Indication of the clock, on-board voltage, temperature in the cabin, warm-up timer during autostart.
  4. Indication of door lock status.
  5. Security mode indication.
  6. Indication that the shock sensor is turned off.
  7. Vibration alert indication.
  8. Indication of central locking control by ignition.
  9. Indication of the “driver call” option.
  10. Alarm indication when the shock sensor is triggered.
  11. Indication of turned on side lights.

Specifications

Technical parameters of the Scher-Khan Logicar 1 car alarm:

  • alarm cycle time - 30 seconds;
  • frequency interval - 433.92 MHz;
  • power of transceiver devices - no higher than 10 mW;
  • current consumption - up to 35 mA;
  • permissible supply voltage is 9-18 V.

Equipment

The kit includes:

  • Logicar processor unit;
  • communicator and backup remote control;
  • shock sensor (with cable);
  • status indicator;
  • antenna unit;
  • motor blocking relay and power connector;
  • limit contact switch;
  • siren;
  • set of connecting harnesses;
  • explanatory stickers and documentation for installation and configuration.

Purpose of the buttons

Having familiarized yourself with the display icons, you can begin to understand what the control buttons on the key fob mean:

  1. Pressing button 1 for 0.5 s is used to: turn on security modes, deactivate the siren, turn on the starter, lock the locks.
  2. Pressing button 2 for 0.5 s turns off the security modes, pauses the alarm mode, turns off the lock and opens the locks.
  3. Using button 3, held for 0.5 seconds, you can turn the screen backlight on or off.
  4. Button 4 is used to check the status of the security system.

Functions

Alarm Sherhan Majikar 9 has the following functionality:

  • “Turbo” mode for cooling a turbocharged engine, preventing wear of parts (the duration of the function cycle can be adjusted by the user);
  • “Comfort” option (used to activate security when closing the doors);
  • alarm mode (light and sound alerts activated by user command scare away criminals);
  • activation of protection when the engine is running;
  • “Pit Stop” function (allows you to activate the protective mode when the key is missing from the ignition switch and the engine is running);
  • Slave mode (allows you to control the alarm using a standard car key fob);
  • hidden security (if an attempt is made to steal, messages are sent only to the control panel located by the owner; the siren does not work);
  • remote engine start at a set time or temperature (the driver can start the engine by issuing a command from the key fob);
  • step-by-step disabling of the security mode by entering an individual password;
  • interior lighting control;
  • control of engine starting using information from the tachometer, generator and battery;
  • automatic blocking of door locks when the ignition is turned off.

Advantages and disadvantages

According to reviews from owners, the Sherkhan Magikar alarm has the following positive qualities:

  • two-way communication (the option can only be used when the key fob is within range, the user sees messages about the status of the vehicle on the screen);
  • reliable protection of the car from criminal acts (the alarm system is equipped with a coding system that prevents signal interception);
  • an expanded set of functions (many necessary modes allow you to configure the car alarm in accordance with the user’s wishes);
  • ease of installation and use (the instructions contain useful recommendations for installing and configuring the system).

The disadvantages include the following characteristics:

  • interruptions in the operation of the Slave (when the turbo timer is turned on, the option becomes useless; it will not be possible to close the locks using the standard key fob);
  • the need to comply with special conditions when activating certain functions;
  • large dimensions of the key fob, causing inconvenience when wearing and using.

Firmware and reprogramming

Programming the Scher-Khan Magicar 5 key fob is relatively easy. If flashing is necessary, it is better to use a PIN code and follow the following instructions:

  1. Within 4 seconds, turn the ignition key three times to different positions, and then turn off the circuit.
  2. Within the next 4 seconds, turn the ignition on again. It is important to ensure that the number of turns matches the secret code value. If everything is done correctly, the alarm will make a single light notification, which will confirm the possibility of entering other symbols.
  3. Turn on the ignition. The number of presses must correspond to the second digit of the code - if everything is correct, the emergency light will blink once.
  4. Using a similar principle, activate the remaining code values.
  5. When the code is entered, all you have to do is press 1 button on the pager and wait until the indicator lights blink once, indicating that the results have been successfully saved.

Following these instructions, you can reflash the alarm key fob in a couple of minutes.

User guide

The system comes complete with an instruction manual in Russian, which outlines all the design features of the Scher Khan Magicar 5 system, tips for setup and use.

PIN Programming

To configure the code you need:

  1. Turn on the ignition and open the driver's door.
  2. Hit the call sensor ten times with slight force, with a break between blows of no more than 1.5 seconds. When there is an impact, the sensitive element in the sensor will begin to signal by turning on the green diode.
  3. After the last hit, the diode will start flashing red. If this does not happen, then errors were made in the procedure and it should be started again.
  4. If the diode is turned on normally, it is necessary to strike the sensor several times (the number corresponds to the first digit of the code). Wait until the number is confirmed by flashing the diode (red, turns on 1.5 seconds after the last strike).
  5. After confirmation, the diode will return to its previous flashing mode. At this time, the second digit should be entered.
  6. The third and fourth digits are entered in the same way.
  7. After recording the last digit, the system will give a single short signal with a siren and an alarm.

How to open a car using a code?

In order to open the car by entering a code, you will need:

  1. Apply ten light blows to the sensor at intervals of no more than 1.5 seconds. Each blow should cause the green diode to blink briefly.
  2. Wait until the red diode starts blinking and apply the number of blows to the sensor corresponding to the first digit of the code. Confirmation of the correctness of the input will be flashes of a red diode with a different frequency. After this, it will switch to private flashing mode, which is a signal to enter the second digit.
  3. Enter the rest of the code data in the same way. If the entry is successful, the system will turn off and the door lock will be unlocked. If an error occurs, the procedure must be started again.

Magikar 5 allows only five input attempts within 30 minutes. After this, the system is blocked for a day and can be turned off during this period of time only by a signal from the key fob.

Enabling security mode

In order to put the electronic system into operating security mode, you must briefly press the first button on the main or additional key fob. When setting, the turn signal lamps turn on and a short signal is given by the siren and buzzer of the key fob. A closed lock icon is displayed on the screen. The shock detection sensor turns on half a minute after the system is turned on.

Enabling security using key fobs

It is possible to disable the security by pressing the first button of any of the key fobs, which will produce a double alarm with lamps and a siren. The icon (open lock) will change on the display.

Deactivating the alarm from the key fob

The system can operate in passive mode, when security is activated half a minute after all doors and covers on the body are closed. If the doors do not open when the system is turned off, it will automatically arm. To use the passive mode, it should be activated by briefly pressing the second and third buttons of the main key fob.

Passive operating mode is active (the Passive icon is lit on the display)

If the doors and trunk lid were opened and closed, the system will turn on the protection half a minute after the lock of the last element is latched.

How to program a new key fob

To configure the new Sherkhan key fob without errors, you must follow the instructions exactly. First of all, it is worth installing batteries in the pager, having first removed the special compartment behind the cover. To remove the cover, you will need to slide the latch.

The new key fob is registered according to the following principle:

  1. The ignition is activated three times and turned off by turning the key in the lock to the “Off” position. It is important for the driver to carry out these manipulations within 4 seconds. Otherwise, you will have to repeat the steps again.
  2. When the light indication works, you need to press button 1 on the key fob. The interval between pressing and blinking should not exceed 4 seconds. If the communicator is paired successfully, the signal lights will blink 2 times.
  3. The rest of the new key fobs are registered in exactly the same way. To exit the settings mode and save them, just do nothing for 4 seconds.

If an additional key fob is not registered

If attempts to program the key fob are unsuccessful, you need to check the device for faults, taking into account the following guide:

  1. Try to get into the salon using the main remote control.
  2. If the security system does not respond to commands from the main key fob, you need to use an additional one. If problems arise far from home, turn off the system using the emergency method, i.e. entering a secret code. When you return home, you need to check the alarm with a second remote control.
  3. If there is no response to the second pager, make sure the transceiver is working properly. Re-register the key fobs. If this does not solve the problem, contact a service center for help and carry out a comprehensive diagnosis.

Sherkhan key fobs with one-way communication standards are equipped with control diodes. Their performance can be determined by the presence of a light indication.

At home or in a workshop, the possibility of transmitting a signal is determined by a tuned radio receiver that receives waves in the range of 280-450 MHz. Depending on the intensity of the sound produced by the remote control, the current state of charge of the batteries is determined. The role of the antenna is performed by a loop of copper wire.

To check the device, you must:

  1. Place the keychain on the top.
  2. Press the button that produces a signal.
  3. Change the orientation of the key fob by rotating the variable capacitor handle. This will allow you to achieve high sound quality. If desired, the capacitor is equipped with a scale of operating frequencies, made using the example of a working device.

After checking the signal level, you can dismantle the device to check the condition of the keys and other operating elements. If visual defects are noticed, including loose legs or peeling, they will need to be re-soldered. Parts with mechanical damage are replaced with similar new ones.

7, alarm, 9, open, A

Security system communicators use liquid crystal displays, which break down if subjected to a sudden shock (for example, when the device falls to the ground). Water and dust get into the contact switches of the buttons, which leads to loss of functionality. If the driver wants to repair the device himself, then he should know how to disassemble the Scher-Khan Magicar 5 key fob and similar systems.

Causes

The most common reasons for disassembling Sherkhan Magikar alarm remotes:

  • the appearance of dark streaks or stripes on the display associated with damage to the panel or contact cable;
  • disappearance of some control indicators on the display;
  • dim backlighting of part of the screen or the entire display;
  • no signal is transmitted when the button is pressed;
  • to execute a command you need to press the key several times or apply force;
  • water entering the internal cavities of the communicator;
  • oxidation of the battery and contact pads;
  • traces of dust and dirt on the inside of the protective glass.

How to open a key fob

Before disassembling the Sherkhan Magikar key fob, you should prepare an instrument screwdriver with a Phillips blade and purchase a fresh battery. Additionally, you may need a soldering station and hot melt adhesive, which is used to fix electronic components. Communicator cases consist of 2 halves connected by a screw and latches located on the sides of the case. Since irreversible damage to the remote control is possible during the work, you should turn off the alarm in advance or prepare a spare key fob.

Magicar 5

To disassemble the head remote control from Magikar 5, you will need:

Remove the protective cover of the battery compartment, and then remove the battery from the niche. Remove the rubber element covering the installation site of the fastening screw. The plug has a round configuration and is located on the front of the remote control housing. Carefully unscrew the screw with a screwdriver. Insert a thin piece of plastic or a knife blade between the housing sections and then separate the halves

When performing work, it is important to prevent breakage of the latches located around the perimeter. Inspect the internal components, remove dirt with a clean cloth. After replacing or repairing faulty parts, reassemble in reverse order.

When performing work, you should take into account the cost of components, which may exceed the price of a new communicator. Test the operation of equipment in various modes.

Magicar 7

If the driver disassembles the Magicar 7 remote control (or a similar device from the Magicar 8), then you need to remove the plug located on the back of the case. A plastic mounting spatula is used to separate the halves; when using metal devices, there is a risk of damaging the plastic parts. Then a circuit board with a soldered display and a rubber protective cover is removed from the case, protecting the button mechanisms from foreign objects. After repair, the removed parts are installed on standard points.

Magicar 9

To open the Sherkhan 9 alarm key fob (an identical product is used on modification 10), you must disconnect the battery. There is a round rubber insert on the back of the case, under which a screw is located. The plug is removed with a needle, which is inserted into the gap between the body and the part. Then the screw is unscrewed and the plastic case is disconnected. Since the housing is made of fragile material with thin walls, do not use physical force to open the halves.

Dirt accumulates on the rubber protective insert, which is recommended to be removed with cotton swabs soaked in alcohol or lighter gasoline. The display and the inside of the glass are wiped with special wipes that do not leave streaks. The damaged display is replaced with a new product; to fix the part, you will need to attach a flexible contact cable. If components need to be replaced, it is recommended that you contact an electronics repair shop.

Related publications:

autotuning.expert

Instructions for setting up autorun

Automatic engine start is one of the most useful functions of all Sherkhan alarms, so every driver needs to know how to set up autostart by studying the instructions for the Sherkhan alarm, on the basis of which the Magikar key fob is prescribed. Before starting programming, you need to deactivate the security functions, turn off the ignition and the hands-free option.

Next, Scher-Khan Magicar 5 is programmed taking into account the following rules:

  1. Automatic launch can only be used in open space with the ability to visually assess the situation.
  2. Do not start the engine if there are people behind you.
  3. If the car is parked, it is important to first apply the parking brake.
  4. When turning on the autostart function, make sure that the gearshift lever is in the neutral position.
  5. Constantly monitor the coolant and oil levels.
  6. Do not allow children to play with the keychain or perform any manipulations.

If you want to bind key fobs with auto start on cars with a manual transmission, you need to use one of the following options:

The first option involves programming the key fobs registered in the system after stopping the vehicle, fixing the parking brake and pressing the neutral position of the gearbox lever. If the engine remains running, open the door, go outside, and then slam it - the power unit should turn off.

If you need to get things out of the trunk, you should use the second method:

  1. After selecting the neutral position of the lever, go outside without closing the door behind you.
  2. Open the trunk and take out the necessary things from it.
  3. Close the door, slam the lid.

There is a third option. It is based on this principle:

  1. Select the neutral position of the gearbox and lock the handbrake.
  2. Close the doors and press the 2nd button on the key fob, holding it for 2 seconds.
  3. Turn off the ignition and leave the cabin.
  4. Close the door and wait for the engine to stop.

By time

To flash the autorun firmware using a timer, you need to be guided by the factory diagram and programming table. First you need to press buttons 3 and 4 and use the diagram with the programming table, which tells you what to do and how to do it. There are two options:

  1. Launch every day with an interval of one day.
  2. Automatic restart after 2/4 or 8 hours.

By temperature and voltage

When programming key fobs (v) to configure autostart according to the temperature range and on-board voltage, you should follow these instructions:

  1. Disable timer start.
  2. Press button 4 at least 21 times.
  3. Select the switching threshold.
  4. Turn on the timer.

general information

Instructions for programming Sherkhan Magikar alarm key fobs

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline! Read more". The Scher Khan Magikar 5 alarm can be installed in cars:

The Scher Khan Magikar 5 alarm can be installed in cars:

  • With any gearboxes;
  • Equipped with engines running on gasoline and diesel fuel;
  • Having a network voltage of 12 V.

Information about the state of the vehicle systems is transmitted as follows:

  • Signals from sensors located in the main devices of the car are transmitted to the cabin computer;
  • The computer converts the information and transmits it to the car owner’s key fob;
  • The display on the key fob visually displays the necessary information that allows the driver to know about the properties of the vehicle system.

You can influence the software remotely, since the radio signal extends over 1.5 kilometers.

Rating
( 2 ratings, average 5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]