If the security equipment is programmed incorrectly, the operation of the automatic or remote start function is disrupted. Resetting the Sherkhan 5 alarm system to factory settings allows you to eliminate the cause of interruptions in operation. The driver then re-sets the parameters, taking into account the design features of the vehicle and additional equipment.
How to remove ZZZ on Magicar?
How to disable ZZZ on Sherkhan 5? Simultaneously press buttons I and III of the key fob and hold them for two seconds. Pressing this combination allows you to remove the service mode, which disables the security system.
Interesting materials:
What moon is May 2022? What is the bookmaker's margin? Which matrix is better than IPS PLS? What pneumatic power is allowed? What is the wattage of the monitor? What is Gazmanov's real name? What is Austria's nationality? What bait for grass carp? What is the amount of cottage cheese per day? Which RAM is better DDR3 or DDR3L?
When a reset or reboot may be necessary
A short list of situations that require returning the parameters of Scher-Khan complexes to their original values:
- spontaneous activation or disabling of security functions;
- false alarms that are not eliminated by adjusting the sensitivity of the working zones of the shock sensor;
- sudden shutdown of the protection mode immediately after activating the function;
- displaying error codes on the communicator screen;
- problems with starting the power unit using a remote or automatic algorithm;
- premature stopping of an automatically started engine.
Engine starting
The Scher-Khan Magicar V alarm allows you to start the car engine using the control key fob. To do this, press button II of the key fob and hold it for 2 seconds (long press). In this mode, the alarm goes into security mode, the car doors are locked, and the engine starts. The duration of the motor operation can be programmed for different time periods:
Starting the engine is accompanied by several indicators confirming the successful execution of the request:
- siren signal
- sound signal from the key fob;;
- flashing of the emergency lights;
- The headlights light up 5 times on the key fob display
If starting the engine fails, the system will repeat attempts a maximum of 2 more times. If after this the engine still fails to start, the alarm goes into normal mode.
In order to start moving the car, the driver, with the engine started from the key fob, needs to open the doors, insert the ignition key and turn it to the ON position. To do this, the driver has 20 seconds after opening the doors. If during this period the key is not turned to the desired position, the system will automatically turn off the engine.
Resetting values for programmable functions from menu No. 1
ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline! Read more"
SCHER-KHAN machine security systems differ in functionality, but not in control principle. Therefore, the instructions for resetting the settings will be the same for both the popular model Sherkhan Magikar 5 and for devices of earlier and later releases.
- Press buttons (the purpose can be found in the instructions) I and II simultaneously.
- Hold them for at least 2 seconds.
- Wait for a short single sound and light signal. The device will perform them once. Sound and light signals make it clear that the user has successfully entered menu No. 1 of Sherkhan 7 or another SCHER-KHAN model.
- Hold button III for 0.5 seconds (short hold). Carry out the procedure three times.
- Pay attention to short signals with light and sound from the device each time you press it. There definitely must be.
- Wait until the alarm emits three consecutive light and sound alarm signals.
The last point is performed after a short time of 7-15 seconds. They symbolize that the factory reset of functions from the programmable menu was successful.
see also
Comments 8
How do you understand “switch autostart to 1 from 3”?
I added a photo, the autostart section is on reservation when you hold down button 2, you need to switch it to Automatic, every time you turn off the ignition, that is, to 1.
If I understand you correctly, then here it is:
PROGRAMMING FUNCTIONS USING THE KEY FOB
Programming STSTS functions using a key fob consists of four steps.
1. Enter programming mode and select the programming menu. To enter Menu No. 1, press buttons I+II simultaneously for 2 seconds. To enter Menu No. 2, press the I+IV buttons simultaneously for 2 seconds. The siren will sound one short signal and the hazard warning light will flash once, thereby confirming the successful completion of STEP 1.
Alarm Settings
To change system settings, use any of the previously registered key fobs. The car must be disarmed and the ignition must be turned off.
The system has two separate settings menus. The first menu is entered by pressing and holding buttons 1+2, and the second menu is entered by pressing and holding buttons 1+4. After the sound signal, you need to select the function number by pressing button 4 and make a short pause, after which the machine will sound the number of the selected function with siren signals. Using buttons 1,2,3 and 4 you can then set the desired function value.
In menu 1 the following functions are associated with autorun operation:
- 12: engine warm-up time at auto start, 5, 15, 25 or 45 minutes for settings 1 to 4, respectively.
- 13: Timer start type. In value 1, the launch occurs every 24 hours according to the time specified on the key fob, in values 2,3 and 4 - every 8,4 or 2 hours from the moment of activation.
- 14: limit the number of auto-starts, maximum 5, 7, 16. When set to 4, the number of timer starts is not limited.
- 16: autostart reservation type. In option 1, ignition interception occurs every time the ignition is turned off, but with a noticeable pause, during which the engine may stall. Option 2 introduces an additional condition: the doors must be closed. If you do not need auto start reservation at a specific moment, just open the door first and then turn off the ignition. There is also a delay before the ignition is intercepted. Therefore, the only adequately working backup option on Magicar 5 is manual reservation (function value 3), when you need to press and hold button 2 of the key fob before turning off the ignition.
- 17: way to complete the algorithm. In option 1, the car will stall after closing the door without arming, in option 2 - similarly, but with automatic arming. In option 3, the engine will stall only after manual arming. This is the only method you should use.
- 20: limitation of periodic starts based on battery voltage. In option 1 it is not set, option 2 sets a threshold of 11.5 V - until the voltage drops below, the start will be blocked. If you select to run every 24 hours, the setting is ignored.
- 21: autostart temperature threshold. In option 1 it is not installed, in options 2-4 the temperature is set to -15, -25 and 60 degrees, respectively (the last option is for operating the air conditioner in the heat).
In menu 2 autorun settings you need:
- 12: minimum starter rotation time, 0.6, 0.8, 1.2 or 2 seconds. It should be set to the possible minimum, since there is no automatic starter cut-off, as with alarms with a tachometer input.
- 13: maximum starter rotation time, 2, 4, 8, 10 sec. It should also be as low as possible in order to preserve the life of the starter and flywheel ring gear.
- 14: increase in starter rotation time during subsequent starting attempts after an unsuccessful one. In option 1, each new start attempt lasts 0.2 s longer than the previous one, in option 2 – by 0.4 s. Option 3 sets the fixed scroll time set by function 12.
- 15: pause between turning on the ignition and attempting to start, 2, 4, 8 and 10 seconds. The first two options are relevant for gasoline engines, options 3 and 4 – for diesel engines with glow plugs.
- 16: pause after stopping the engine until the ignition is turned off. 0, 4, 15 seconds or 4 with restart attempts.
The remaining autorun settings are related to the connection diagram to a specific car and should not be changed by the user.
Autostart based on temperature
Automatic start can be set when a certain air temperature is reached, which is determined by temperature sensors installed in the car interior. Temperature autostart can only be used in combination with timer autostart. To set autostart only when a certain temperature is reached, you must:
- select autorun by timer;
- turn on temperature control - press the IV button 21 times;
- select the required temperature mode (key II — –15 °C, key III — –25 °C, button IV — +60 °C);
- enable autorun mode by timer (see above).
Resetting values for programmable functions from menu No. 2
The principle of operation will be similar, only to enter menu No. 2 you need to hold down for at least 2 seconds. key fob buttons numbered I and IV. Performing this action will result in short alarms with light and sound. They confirm that the login was successful.
Next, reset the settings like this:
- Press the key fob button III for 0.5 seconds three times.
- Wait for a short emergency flash signal and siren.
- Wait for reset confirmation. This will happen after a short time. Confirmation will be a three-time siren sound and a three-time flash.
The reset procedure is not difficult. But professionals do not recommend doing it yourself. The reason for this is the possible and unpredictable failure of various components of the car - it is impossible to start the engine, turn on the security mode, etc. It is better to entrust this procedure to a professional installer.
Autorun programming
The Scher-Khan Magicar V alarm allows you to automatically start the engine in various modes:
Starting the engine every 24 hours allows you to start the engine at the same time every day, which is convenient, for example, for warming up in the morning. Starting every 2 hours allows you to maintain the temperature of the engine and interior on cold days or, conversely, cool the interior in the summer season. Both timer modes cannot be used simultaneously. The autorun mode is selected through the programmable functions menu.
To program autostart every 2 hours, you need to briefly press buttons II and IV. In this case, the engine will automatically start 2 hours after pressing. In this case, setting the time is not required.
To automatically start the engine every 24 hours, you must first set the exact time on the key fob, if it is not installed. (how to do this - see above). Setting up automatic engine start is as follows:
- you need to press buttons II and IV and turn off the Timer mark;
- select the start time using keys I and II;
- Press keys II and IV again and turn off the Timer label.
When the engine starts automatically, the key fob display shows a countdown until the engine is turned off.
Adjusting the shock sensor
The impact sensor notifies the car owner about an incident with the car while the car is parked with the alarm on.
Scher-Khan Magicar V alarm sensors are two-level: with a weak impact, a beep sounds 4 times and the alarm flashes 4 times. If there is a strong impact, the key fob goes into alarm mode, lasting 30 seconds - 30 flashes of the emergency lights and 30 short beeps. Shock sensors can be turned on or off by pressing the combination of buttons I and III and holding them for 2 seconds.
Adjusting the impact sensor helps to avoid false alarms of the accident warning sensor, since with a sensitive sensor, even the passage of a neighboring car can be falsely perceived by the system as an emergency impact. To adjust the sensitivity of the sensors, physical access to them is required; you can find out about the location of the shock sensors at a service station. There are regulators installed on the sensors themselves; turning clockwise increases sensitivity, counterclockwise turns it down until the sensor is completely turned off.
SCHER-KHAN brand car alarms of all series are reliable and multifunctional security systems characterized by stable operation. But if used incorrectly or for a long time, or if the settings are set incorrectly, malfunctions may occur in the operation of the alarm system.
Automatic switching off and on of the security mode, disarming immediately after installation, no reaction to an impact, errors on the display, inability to start the engine - these are just a few common problems when using SCHER-KHAN. What to do if there are problems? It is recommended to perform a factory reset.
