Lada 2110 White Lady Logbook euro 2 dashboard and granta steering wheel, everything was installed personally

Greetings my subscribers and guests of my logbook

This morning I woke up, and my hands were itching since yesterday, I endured it until the morning. I again took some Madeleine and scissors and went to the car. I removed the center console and began to inspect the whole thing, where the joints of all the parts that are installed on it are. I carefully took everything apart, taped the material, assembled it and moved everything normally. So we move on. Some parts, such as air ducts, had to be removed and installed several times to achieve a result that suited me. After gluing everything became much tighter, I pulled the console with both hands and everything was quiet EXCELLENT what I wanted). I didn’t stop there and glued the remaining material onto the fuse cover, the side panel plugs, the frame on the instrument panel, and glued a small square to the place where the alarm key fob knocks on the steering column casing. I also glued it to the inner velvets, they were still removed when I rolled the glass with film. The glass sits much tighter and doesn’t rattle on bumps, that’s all. We look, we rate, we comment

Removing the standard radio in Grant Lux

The difference between grants of the luxury configuration: the MMS (multimedia system) installed from the factory. This is a 2 din device.

To remove standard acoustic grants:

• take a knife or plastic spatula to dismantle the acoustics and disconnect the decorative trims to the right and left of the radio. It is not necessary to take pictures;
• in the gap between the cover and the panel we find the head unit lock. There are two of them on both sides. Press it out with a screwdriver;
• we take out the GU on ourselves.

Everything is described in detail in the video:

Replacing the standard MMC in Grant

The process - after removing the acoustics, we install a new system.

Difficulties: you may have to finish the fastenings of the new system for VAZ ones. Plus you need the right frame. The factory MMC frame may not fit.

When you buy a new PG for your car, you need to buy a frame for it specifically for Grants. Otherwise there will be holes in the panel.

Installation of the Luxe central console from Lada Kalina on Lada Granta

Cars of the Lada Kalina family in the Luxe configuration have a center console with a visor, which allows you to place a multimedia system.
Currently, this console is not produced by the factory, but you can install it yourself on the Lada Kalina in the “Standard” or “Norma” configuration, as well as on the new Lada Granta FL family. The modification process depends on which instrument panel (dashboard) is installed on your car.

Firmware versions of Lada Granta and Kalina 2 instrument panels

The table was compiled (is in the process of being adjusted) based on reviews from car enthusiasts (please add comments). There is no guarantee that all data is correct!

* — DTNV — outside air temperature sensor, DTOZH — coolant temperature sensor.

Download firmware (dumps of instrument panel firmware, links available for site users):

• 2190-50 — To download files you need to log in to the site
• 2192-50 (software 1.9) - To download files you need to log in to the site
• 2190-00-029 — To download files you need to log in to the site
• 219020-060 — To download files you need to log in to the site
• 219020-076 — To download files you need to log in to the site
• 219020-087 — To download files you need to log in to the site
• 219020-090(AT) - To download files you need to log in to the site sent by ARS190475
• 219020-091 — To download files you need to log in to the site
• 219020-096 - To download files you need to log in to the site sent by ARS190475
• 219040-046 — To download files you need to log in to the site
• 219040-047 — To download files you need to log in to the site
• 2190-3801010-50 Software: 6.6 (KP with two displays) - To download files you need to log in to the site sent by ARS190475
• 2190-3801010-50 Software: 7.2 (KP with two displays) - To download files you need to log in to the site sent by ARS190475
• 219220-014 — To download files you need to log in to the site
• 219240-006 - To download files you need to log in to the site sent by ARS190475
• 219240-007 — To download files you need to log in to the site
• 219240-009 — To download files you need to log in to the site
• 219240-012 — To download files you need to log in to the site
• 219240-014 — To download files you need to log in to the site
• 219250-2.5 (KP with two displays) - To download files you need to log in to the site sent by ARS190475
• 219020-092_for_076 — To download files you need to log in to the site
• 219020-092 — To download files you need to log in to the site (author)
• 2190-3801010-50 Software: 7.1 - To download files you need to log in to the site

How to remove the dashboard for sizing

Recently a guy asked how to remove the dashboard for sizing. I want to share my impressions about this process. Suddenly someone wants to do this too. So here it is. I removed the panel last summer. Also for sizing. I did everything alone. I’ll say this: you can remove/install it alone, but it’s very messy. It's easier with two people, but I don't think it's much easier. Don't believe the repair book, it's much more complicated than it says. Too much will have to be removed in addition to the panel itself: the central trim, air duct tubes, gearbox housing, handbrake housing, floor tunnel, passenger airbag (if equipped), A-pillar trims, tidy. There are a lot of different screws and self-tapping screws, during assembly it is easy to get confused as to which ones were screwed in where. If I'm not mistaken, there are 26 screws alone for securing the panel itself! There are two treacherous screws on the left and right right under the windshield, which you can’t unscrew with a regular screwdriver, you can’t get under them. While the panel is being removed, you are left without glass blowing, and in current weather conditions this is fraught with consequences, including an accident due to fogged windows. If you just park the car. In terms of time: removal took 3 hours, installation took 4 kopecks. The steering wheel gets in the way. The left air duct pipe did not want to fall into place, it rested either on the body or on the windshield, it took me a whole hour just to do this. According to the results: the panel became a little more assembled, but after a WEEK it began to crunch again. In addition to this, the airflow on the windshield has become uneven - it blows weaker in the middle than at the edges. I’m generally silent about the numerous scratches on the dashboard and front door trims. You can remove them with an autogen lighter, but still the appearance is no longer marketable. Summarizing all of the above, from the bottom of my heart I HIGHLY DO NOT RECOMMEND doing this. You'll only make it worse. But this is purely my opinion, and then see for yourself. Maybe if you have experience in this matter, it will be easier for you. But I wouldn’t do this again now for any money, there are too many body movements and nuances

Soundproofing panel/dashboard Grants

There can be many sources of rattling and squeaking in dashboards, let's look at the most common ones:

The radio/radio plug is rattling. Solution: use anti-creak or sealant.

The air duct rattles at the point of contact of the windshield blower nozzle. Solution: use silicone sealant or anti-squeak.

The airbag plug creaks. Solution: when installing the plug, coat it with sealant, or use bitoplast (5mm or 10mm).

The panel trim creaks. Solution: Remove the dashboard trim and glue the places where it touches (on the panel and on the trim itself) with bitoplast or anti-squeak.

The panel/dashboard creaks. Solution: The solution to the problem of panel rattling must be comprehensive.

1. It is recommended to weight the dashboard using vibration materials (for example, 1 sheet of STP Gold 250 RUB/sheet is enough). Heat the pieces with a hairdryer and glue the panel with a “vibra” using a hard roller. A heavier Granta panel will produce less extraneous sounds.
2. Wrap the torpedo wires with anti-squeak.
3. Treat all removable elements with anti-squeak (panel trim, airbag cover, glove compartment, etc.)
4. Tighten all possible panel mounting nuts.

Soundproofing the dashboard is a modification that should be done at the factory, but AvtoVAZ provides car owners with the opportunity to do this with their own hands.

Remember that the best sound insulation is when a set of works has been completed not only to isolate from external noise (noise from wheels, engine, wind, etc.), but also to eliminate creaks and crickets inside the car.

Torpedo Granta dorestayl

The panel from Kalina began to be installed on the pre-restyling Granta immediately before the release of the updated Lada Granta FL family.

If the dashboard of your car is like in the left photo, then you will need to replace a number of parts of the instrument panel (dashboard) with parts from the Lada Kalina dashboard:

• 21925-5325011-00 Instrument panel VAZ-21925 Lux with air duct SB AvtoVAZ OJSC
• 21920-7905020-00 USB cable 2192
• 21925-5326014-00 Overlay for the instrument panel console LUX
• 21920-5326014-00 Instrument panel console trim NORMAL - lower, depending on the climate unit
• 21920-5303014-00 Glove box body 2192
• 21920-3710010-00 Hazard switch
• 21920-5303016-00 Cover of the glove box of the instrument panel
• 21920-5325322-00 Fuse box cover

This is a global alteration of the car interior, which cannot be called rational.

After this, you can begin installing the center console according to the instructions below.

Alternative torpedo

The alternative dashboard is softer than the standard “tens” dashboard, but the main advantage is the absence of unpleasant grinding and squeaking. Motorists decide to get rid of the standard one precisely because of the squeaking. For the VAZ 2110 car there are several types of panels that differ in design.

The panel is sold as a set:

• The panel itself, which is an alternative to standard plastic.
• Buttons, brackets and inserts for blowers and instrument panels.
• A set of wires and a block for a double switch.
• Buttons for low beam, heating, dimensions and fog lights.
• Plugs for buttons are installed in places where keys are not needed.

How to remove the dashboard of a Lada Granta

We remove the instrument panel when it is necessary to change the wiring or when repairing the interior heater; we also remove the panel during body work.

We prepare the vehicle for work. Disconnect the negative terminal of the battery.

Drain the coolant from the engine cooling system.

We remove the filter of the heating and ventilation system.

Using a Phillips screwdriver, unscrew the four self-tapping screws that secure the heating system filter casing to the instrument panel.

Loosen the clamps securing the heater hoses and remove the hoses from pipes 2 of the heater radiator. Using a 10mm socket, unscrew nut 1 of the stud securing the flange of the heater radiator pipes to the front panel.

Removing the cover of the mounting block

Removing the instrument cluster

Removing the floor tunnel lining (article - How to remove the floor tunnel lining of a Lada Granta)

We disconnect the steering column from the instrument panel frame and lower it to the floor of the body or remove it completely

Remove the central trim of the instrument panel (beard), (see How to remove the central trim of the instrument panel Lada Granta)

We take out the seals of the front door openings

Unfastening it from the clips, remove the left side trim of the instrument panel. We also remove the right side trim of the instrument panel.

Torpedo Granta dorestayl

The panel from Kalina began to be installed on the pre-restyling Granta immediately before the release of the updated Lada Granta FL family.

If the dashboard of your car is like in the left photo, then you will need to replace a number of parts of the instrument panel (dashboard) with parts from the Lada Kalina dashboard:

• 21925-5325011-00 Instrument panel VAZ-21925 Luxury with air duct SB AVTOVAZ OJSC
• 21920-7905020-00 USB cable 2192
• 21925-5326014-00 Overlay for the instrument panel console LUX
• 21920-5326014-00 Instrument panel console trim NORMAL - lower, depending on the climate unit
• 21920-5303014-00 Glove box body 2192
• 21920-3710010-00 Hazard switch
• 21920-5303016-00 Cover of the glove box of the instrument panel
• 21920-5325322-00 Fuse box cover

This is a global alteration of the car interior, which cannot be called rational.

After this, you can begin installing the center console according to the instructions below.

How to remove the front console of a Lada Granta

Many Lada Granta owners sometimes need to remove the central trim on the dashboard. The reasons for this may be different, such as eliminating unnecessary squeaks or installing a radio. Today I will tell you how to dismantle it.

how to remove the radio panel on a grant

The space for installing the radio in the dashboard console of the Lada Granta car is designed for 1 DIN radio. Now you need to remove the metal frame from the radio and install it in the place where the plastic pocket was. 231 videos found. Kalina2 How to disassemble and remove the radio panel (MMC). Uploaded October 5, 2013. Uploaded August 16, 2015. Details can be found here. Granta. Removing the horseshoe. Uploaded May 18, 2015. Remove the center trim of the instrument panel console. Next, remove the glove box cover.

How to remove the air duct damper control unit of a Lada Granta. How to remove the instrument panel of a VAZ 2106. However, it will not be possible to remove the radio panel if you do not first dismantle the climate control panel. Below it are metric screws (A, B) that secure the media center shield from below. How to properly remove a radio without special keys. Many motorists face the problem of removing the radio in their car. The first step is to remove the front panel of the radio.

To remove the car radio, use the same algorithm. After you have removed the cover covering the radio, you will see two connectors.

Do-it-yourself tuning of the Lada Granta interior with video and photos

Modern domestic cars are distinguished by maneuverability, endurance and excellent performance characteristics. However, where they definitely lose is in the configuration and convenience of the interior. The Lada Granta is no exception. Many sacrifice the aesthetic component, because compared to foreign cars, the VAZ differs favorably in price.

Others choose tuning, which can actually be done in some places even with your own hands, because in workshops such changes can cost significant sums. Internal and external design redesign is not so difficult if you know and take into account some of the nuances.

Basics of basic tuning

The Lada Granta has minor mechanical and aesthetic defects, which will not be difficult to identify after the first run-in. These are some technical details, first of all, which the manufacturer promised to take into account in the following modifications. Among the most common problems that you can actually fix yourself without a trip to a service station are:

1. High standard suspension.
2. Inconvenient sunroof.
3. No spoiler.
4. “Faded” and uncomfortable front panel.
5. Poor quality steering wheel finish.
6. Unattractive upholstery and lack of armrests and headrests.

All these points can be redone by carrying out simple tuning yourself. The easiest way is to re-equip the interior first, because to deal with, for example, the suspension, you need some experience, while changing the trim material will not take much effort, money and does not require special experience.

Changes in the salon: where to start

Practice shows that the Lada Granta has one weak point, which is noted by almost all motorists. This is the front instrument panel. The backlight intensity here is extremely low, due to which the driver in the dark has to strain his eyes to see the speed scale. There is a simple solution - add LED strips under the panel, which solves the problem to some extent. This kind of work is not difficult; you can do it yourself. You need to follow these steps:

• remove the panel fastening;
• remove glass and instruments;
• install LED elements;
• connect power;
• do everything listed in reverse order.

Let's look at this tuning in more detail. In order to remove the panel and gain access to the devices, you need to unbend all the fixing latches. After this, you can remove the back cover. The Lada Granta has a small plus in this regard - small recesses with which you can easily pull out this part. We access the display. If you bought a used car, then an unpleasant surprise may be the fact that the display is soldered to the walls. In this case, it is advisable to use a desoldering pump.

After the display is removed and all the antennae move freely in the landing zone, you need to unscrew the factory LEDs and put new ones in their place. Then we connect the network and check the operation of the light bulbs. If they burn normally, then you can reassemble. As a result, you will see how the appearance of the cabin has changed just thanks to a slightly improved dashboard.

Tuning for convenience on the go

Not only the beauty of the interior plays a role for drivers, but also comfortable driving conditions. So, you can reupholster the steering wheel with new material, adding softness to it, put new covers on the seats, and install armrests and headrests. All these actions are very easy to do with your own hands.

To make such a change to the interior of a Lada Granta car, like most others, you must first remove the seat backs. To do this, remove the upholstery and unfasten the zipper. Use a screwdriver to unscrew all the plastic fasteners. The headrests are attached with brackets, marking the future locations. Next, in the selected area on the seat pipe, we drill holes and fasten the brackets, and tighten the fasteners with a wrench. At the end, carefully return the upholstery to its place.

That's all. As you can see, it is not at all difficult to carry out minimal tuning in Lada with your own hands.

https://youtube.com/watch?v=Za-QxK4Eopk

How to remove the dashboard of a Lada Granta

We remove the instrument panel when it is necessary to change the wiring or when repairing the interior heater; we also remove the panel during body work.

We prepare the vehicle for work. Disconnect the negative terminal of the battery.

Drain the coolant from the engine cooling system.

We remove the filter of the heating and ventilation system.

Using a Phillips screwdriver, unscrew the four self-tapping screws that secure the heating system filter casing to the instrument panel.

Loosen the clamps securing the heater hoses and remove the hoses from pipes 2 of the heater radiator. Using a 10mm socket, unscrew nut 1 of the stud securing the flange of the heater radiator pipes to the front panel.

Removing the cover of the mounting block

Removing the instrument cluster

Removing the floor tunnel lining (article - How to remove the floor tunnel lining of a Lada Granta)

We disconnect the steering column from the instrument panel frame and lower it to the floor of the body or remove it completely

Remove the central trim of the instrument panel (beard), (see How to remove the central trim of the instrument panel Lada Granta)

We take out the seals of the front door openings

Unfastening it from the clips, remove the left side trim of the instrument panel. We also remove the right side trim of the instrument panel.

How to remove a beard on a grant

Complete information on the topic “how to remove a beard on a grant” - all the most relevant and useful information on this issue.

download photo to mobile phone

Operation and maintenance manual

and car repair Lada Granta VAZ 2190

Removing and installing the central lining of the instrument panel console Lada Granta VAZ 2190

1. Disconnect the wire from the negative terminal of the battery.

2. Remove the audio system head unit and disconnect the antenna cable tip and wiring harness connectors from it.

3. Use a mounting spatula to pry off the handle of the incoming air temperature and distribution controls.

4. . and remove them from the axles.

5. Pull and remove the recirculation damper control lever handle.

6. Using a pointed tool (preferably a special plastic spatula), pry up the central trim of the instrument panel console and, overcoming the resistance of the latches (Fig. 11.12) located along the contour of the console trim.

7. . move the console trim away from the dashboard.

8. Disconnect the wiring harness connectors from the switches located on the console trim.

9. Remove the center trim of the instrument panel console.

10. Install the central trim of the instrument panel console on the Lada Granta VAZ 2190 car in the reverse order of removal.

Rice. 11.12. Location of the fastening clamps for the central lining of the instrument panel console of the Lada Granta VAZ 2190 (view from the inside of the console lining)

Parts and consumables:

• Oil filter
• Engine oil
• Rags

• Open-end wrench 10 mm
• Ratchet wrench
• Extension
• 8 mm head
• 10 mm high head
• 13 mm head
• 21 mm head
• Torx T20 socket
• Medium Phillips screwdriver
• Large flat screwdriver

Carry out work if it is necessary to replace the instrument panel, panel wiring harness and elements of the heating and ventilation system.

1. Disconnect the wire terminal from the negative terminal of the battery.

2. Drain the engine cooling system as described in this article.

3. In the engine compartment, remove the heating and ventilation system filter as described here.

4. Using a Phillips screwdriver, unscrew the four self-tapping screws securing the heating and ventilation system filter casing to the instrument panel and remove the casing.

5. Loosen the clamps securing the heater inlet and outlet hoses and remove the hoses from pipes 2 of the heater radiator. Using a 10 mm high socket with an extension, unscrew nut 1 of the stud securing the flange of the heater radiator pipes to the front panel.

6. Inside the car, remove the mounting block cover as described in this article.

7. Remove the instrument cluster as described here.

8. Remove the floor tunnel lining as described in this article.

9. Disconnect the steering column from the instrument panel frame and lower it to the floor or remove the button completely, as described in this article.

10. Remove the instrument panel center trim as described here.

11. Remove the seals for the right and left door openings at the installation locations of the instrument panel and the A-pillar upholstery.

12. After overcoming the resistance of the clamps, remove the left side trim of the instrument panel.

13. Similarly, remove the right side trim of the instrument panel.

14. Use a screwdriver to pry up the upholstery of the left front pillar and, overcoming the resistance of the pistons, remove the upholstery.

15. Similarly, remove the right front pillar trim.

16. Remove the headlight beam adjustment knob by pulling it towards you.

17. Using a 21 mm socket, unscrew the nut securing the regulator to the instrument panel and remove the nut.

18. Remove the headlight beam adjustment control from the instrument panel hole.

19. Using a screwdriver, press out the two latches on the glove box and remove the top edge of the box from the instrument panel.

20. Open the glove box to a large angle and, applying the necessary force, pull the four split hinges of the box from their axes.

21. Near the opening of the left door, use a 10 mm socket to unscrew nut 1 securing the tip of the “mass” wire and remove it from the stud.

22. Using a 10 mm socket, unscrew the two nuts securing the ground wire lugs to the right bracket of the instrument panel console and remove the wire lugs from the studs.

23. Using a 13 mm socket, unscrew the bolt securing the right bracket of the instrument panel console to the body bracket.

24. Similarly, unscrew the bolt securing the left bracket of the instrument panel console to the body bracket.

25. Squeeze the two clips and disconnect the wiring harness connector from the brake light switch.

How to remove the center console of a Lada Granta

Greetings my subscribers and guests of my logbook

This morning I woke up, and my hands were itching since yesterday, I endured it until the morning. I again took some Madeleine and scissors and went to the car. I removed the center console and began to inspect the whole thing, where the joints of all the parts that are installed on it are. I carefully took everything apart, taped the material, assembled it and moved everything normally. So we move on. Some parts, such as air ducts, had to be removed and installed several times to achieve a result that suited me.

After gluing everything became much tighter, I pulled the console with both hands and everything was quiet EXCELLENT what I wanted). I didn’t stop there and glued the remaining material onto the fuse cover, the side panel plugs, the frame on the instrument panel, and glued a small square to the place where the alarm key fob knocks on the steering column casing. I also glued it to the inner velvets, they were still removed when I rolled the glass with film. The glass sits much tighter and doesn’t rattle on bumps, that’s all.

We look, we rate, we comment

Removing the center console of Lada Granta

Many Lada Granta owners sometimes need to remove the central trim on the dashboard. The reasons for this may be different, such as eliminating unnecessary squeaks or installing a radio. Today I will tell you how to dismantle it.

How to remove the dashboard of a Lada Granta

We remove the instrument panel when it is necessary to change the wiring or when repairing the interior heater; we also remove the panel during body work.

We prepare the vehicle for work. Disconnect the negative terminal of the battery.

Drain the coolant from the engine cooling system.

We remove the filter of the heating and ventilation system.

Using a Phillips screwdriver, unscrew the four self-tapping screws that secure the heating system filter casing to the instrument panel.

Loosen the clamps securing the heater hoses and remove the hoses from pipes 2 of the heater radiator. Using a 10mm socket, unscrew nut 1 of the stud securing the flange of the heater radiator pipes to the front panel.

Removing the cover of the mounting block

Removing the instrument cluster

Removing the floor tunnel lining (article - How to remove the floor tunnel lining of a Lada Granta)

We disconnect the steering column from the instrument panel frame and lower it to the floor of the body or remove it completely

Remove the central trim of the instrument panel (beard), (see How to remove the central trim of the instrument panel Lada Granta)

Unfastening it from the clips, remove the left side trim of the instrument panel. We also remove the right side trim of the instrument panel.

Soundproofing panel/dashboard Grants

How to remove the door trim on a Lada Granta with your own hands (video instructions)

Starter fuse for Lada Granta

Replace the lock, repair the window regulator or speakers - in order to do all this you will need to remove the card from the door. Therefore, now we will describe in detail how to remove the trim from the door of a Lada Granta so that your liftback does not suffer from careless and ill-considered actions.

The procedures for removing trim from the front and rear doors of a car are slightly different, but we will tell you in detail about each process so that you can cope with this not very difficult job yourself.

Additional sound insulation may also be a reason to remove the trim from some interior elements, but this is a separate story that requires a special approach.

Step-by-step removal of the front door card

To replace the casing, you will need a set of screwdrivers, but it is worth stocking up on spare clips, which are necessary for fastening the casing.

First, for safety reasons, you need to remove the negative terminal from the battery.

1. Unscrew the door lock button until you can remove it completely.
2. Use a screwdriver to pry up the screw cap that secures the trim to the door.
3. Using a cross-shaped tool, unscrew the screw itself.
4. Do the same procedure with the screw located in the armrest recess, as well as its two screws at the bottom of the card.
5. Pry the top of the handle with a flat tool to remove it.
6. Unscrew the two screws inside the handle that are found under the top trim.
7. Once the trim is no longer attached to the door, you need to start removing it from the lower front edge. To gain access to it, just use a flat tool to pry the edge that fits tightly to the metal of the door.
8. As you remove the upholstery material, you must disconnect the pins holding it. At such moments you should be extremely careful not to damage them. In total, there are 8-9 pistons (clips) on the Lada Granta door, and they are located along the perimeter of the upholstery fabric, but closer to the edges.
9. From the corner, move in both directions at once while removing the card.
10. Remove the lock lock rod from the hole.
11. Disconnect the exposed block with the power window wires by squeezing the locking element. In cars that do not have power windows, remove the lever seal from the handle hinge.
12. Only then can you completely remove the door trim.

Step-by-step removal of the rear door card

The tools are the same, since the very essence of the process is not much different from the previous one.

1. Using a flat tool, press out the window handle retaining element.
2. Move the lock to the side and remove the handle completely.
3. Remove the second part of the handle and the socket.
4. Unscrew the locking element of the lock.
5. Use a flat tool or a metal spatula to pry off the top of the handle. Take it off.
6. Remove the two screws inside the handle.
7. Use a long, flat tool to pry up the trim underneath, pushing it between the metal of the door and the card.
8. During the removal process, snap off the pistons, trying as much as possible not to damage them. There are more clips on the back door than on the front - 10 pieces.
9. That's all, now you can completely remove the trim from the rear door of the Lada Granta.

Installing the casing is slightly different from dismantling it, not only in the sequence of actions, but also in why exactly the old one was removed. Therefore, this issue will be considered separately.

How to remove the dashboard for sizing

Recently a guy asked how to remove the dashboard for sizing. I want to share my impressions about this process. Suddenly someone wants to do this too. So here it is. I removed the panel last summer. Also for sizing. I did everything alone. I’ll say this: you can remove/install it alone, but it’s very messy. It's easier with two people, but I don't think it's much easier. Don't believe the repair book, it's much more complicated than it says. Too much will have to be removed in addition to the panel itself: the central trim, air duct tubes, gearbox housing, handbrake housing, floor tunnel, passenger airbag (if equipped), A-pillar trims, tidy. There are a lot of different screws and self-tapping screws, during assembly it is easy to get confused as to which ones were screwed in where. If I'm not mistaken, there are 26 screws alone for securing the panel itself! There are two treacherous screws on the left and right right under the windshield, which you can’t unscrew with a regular screwdriver, you can’t get under them. While the panel is being removed, you are left without glass blowing, and in current weather conditions this is fraught with consequences, including an accident due to fogged windows. If you just park the car. In terms of time: removal took 3 hours, installation took 4 kopecks. The steering wheel gets in the way. The left air duct pipe did not want to fall into place, it rested either on the body or on the windshield, it took me a whole hour just to do this. According to the results: the panel became a little more assembled, but after a WEEK it began to crunch again. In addition to this, the airflow on the windshield has become uneven - it blows weaker in the middle than at the edges. I’m generally silent about the numerous scratches on the dashboard and front door trims. You can remove them with an autogen lighter, but still the appearance is no longer marketable. Summarizing all of the above, from the bottom of my heart I HIGHLY DO NOT RECOMMEND doing this. You'll only make it worse. But this is purely my opinion, and then see for yourself. Maybe if you have experience in this matter, it will be easier for you. But I wouldn’t do this again now for any money, there are too many body movements and nuances

Cold welding – hot idea

So, let's begin. The work is very delicate and painstaking, one might even say a piece of jewelry, so we must be patient. The most ideal option for making such an invention as a frame for a 2 din Grant radio, in my opinion, is to mold an adapter frame from cold welding, and besides, I was not the only one who came up with this idea. The transition frame needs to be “sculpted” on the center console with the radio. To do this, you should go to a hardware store and buy there:

1. Cold welding 2. Masking tape 3. Nylon thread

You're probably wondering, why use masking tape? And this is in order to paste over the radio according to the form of welding, so as not to glue it to the panel forever. Be sure that everything will work out, and soon you will have a frame for Grant’s 2 din radio.

In order for the mold to be easily removed later, we apply cling film on top of the tape, again following the shape of the weld. Also, to give our frame greater strength, it is recommended to run thin copper wire around its perimeter.

To make it easier to remove the frame, you should put a thread under it. In my case, it turned out according to the well-known saying “The first pancake is lumpy”, I stuck a cold weld right on top of the masking tape and did not put a thread under it (although this would hardly have changed anything), the result is a broken newly made 2 din grant frame. Learn from other people's mistakes.

Don’t be surprised if it takes some effort to remove the cling film from welding; act carefully and you won’t break anything.

After we have removed the “freshly molded” frame, we should immediately take care of the fastenings, because somehow it must hold on.

To do this, we make two thin fasteners, similar to those that are placed on the caps, having previously measured the diameter between the tunnel for the radio and the upper edge of the panel. If you blinded too much, don’t worry, we have sandpaper and desire.

So, the transition frame for the Lada Grant is ready. Now we get to work on grinding off all the excess and giving our frame for the 2 din radio a smooth and attractive look. To do this, we use sandpaper No. 40, and if you have gone through with force and ground off the excess, we use the same cold welding to build up. I would like to immediately warn you that the work of adjusting the frame requires the greatest endurance.

After eliminating all the irregularities, we begin the process of preparing the frame for applying putty and primer. If you have taken on this painstaking work, then you are probably patient and a person striving for ideals, and you probably love your Lada Granta very much. After all, many simply would not take up this matter. In the meantime, let’s continue the so-called journey towards the ideal in the “2 din Grant Frame” case.

How to remove the dashboard of a Lada Granta

Lada 2109 aquarium Logbook Grant trunk lock and sensory trunk We remove the instrument panel when we need to change the wiring or when repairing the interior heater, we also remove the panel during body work.

We prepare the vehicle for work. Disconnect the negative terminal of the battery.

Drain the coolant from the engine cooling system.

We remove the filter of the heating and ventilation system.

Torpedo Kalina or Granta FL

The following are instructions for cars with such a dashboard:

• instrument panel trim (21925-5325182)
• central air ducts (or intermediate air duct housing for the monitor for Lada Kalina 2) (2195-8104209/08)
• solar radiation sensor (21920-8121300)

• multimedia display (article 21920-7900100, make sure you have an interface cable)
• multimedia equipment (21920-7900200 or navigation 21920-7900300)

1. Remove the instrument cluster, glove compartment, center trim and air ducts (move back a couple of fasteners from above).
2. Install the air ducts, modifying the fastenings in place (for example, use furniture corners).

As a result, the air ducts should go down a little:

1. Install the screen and multimedia system on standard mounts.
2. Connect the display to the multimedia unit.
3. Attach the solar radiation sensor to the frame.
4. Install the center console.

Source

Soundproofing panel/dashboard Grants

There can be many sources of rattling and squeaking in dashboards, let's look at the most common ones:

The radio/radio plug is rattling. Solution: use anti-creak or sealant.

The air duct rattles at the point of contact of the windshield blower nozzle. Solution: use silicone sealant or anti-squeak. The airbag plug creaks. Solution: when installing the plug, coat it with sealant, or use bitoplast (5mm or 10mm). The panel trim creaks. Solution: Remove the dashboard trim and glue the places where it touches (on the panel and on the trim itself) with bitoplast or anti-squeak.

The panel/dashboard creaks. Solution: The solution to the problem of panel rattling must be comprehensive.

1. It is recommended to weight the dashboard using vibration materials (for example, 1 sheet of STP Gold 250 RUB/sheet is enough). Heat the pieces with a hairdryer and glue the panel with a “vibra” using a hard roller. A heavier Granta panel will produce less extraneous sounds.
2. Wrap the torpedo wires with anti-squeak.
3. Treat all removable elements with anti-squeak (panel trim, airbag cover, glove compartment, etc.)
4. Tighten all possible panel mounting nuts.

Soundproofing the dashboard is a modification that should be done at the factory, but AvtoVAZ provides car owners with the opportunity to do this with their own hands.

Remember that the best sound insulation is when a set of works has been carried out aimed not only at insulating from external noise (noise from wheels, engine, wind, etc.), but also eliminating creaks and crickets inside the car.

How to flash the firmware

• Buy an SD card, format it in FAT, exFAT format;
• We download the firmware for free on the manufacturer’s official website;
• We save the data in the root directory of the SD card;
• We insert the SD card into the slot on the radio, start it, wait for the update to finish;
• Turn on and off the module;
• We customize the new interface for ourselves.

If the firmware is installed incorrectly, additional screen calibration using the CAN bus will be required. It is impossible to do this yourself, only in a service station. After successful flashing, the following is available:

• graphic equalizer;
• viewing photos, pictures, videos;
• improved sound quality;
• possibility of installing a navigation system.

Disadvantages of a standard radio

• Outdated firmware from the “box”;
• Not all options are initially available;
• The need for periodic software updates;
• Push-button interface.

Choosing the right radio size

We carry out installation either independently or by contacting specialists at the service center. In the second case, the service is paid.

By default, all VAZ and Lada models are equipped with a 1-DIN radio. The opening dimensions correspond to: 180 x 50 mm. This is an old standardization that has been in force since the times of the USSR. Modern audio modules can be purchased complete with a pre-installed LCD display. The size of the opening must comply with the standard: 180 x 100 mm, that is, doubled in height. Size marking: 2-DIN.

To install the radio in the Granta liftback, cut out the top pocket, remove the plastic, and install the assembled module. For a beginner, the process will seem somewhat complicated, so strictly follow the instructions.

Granta FL

The modern version of Fl 2022 differs little structurally from its prototype. The car tidy is removed in the same way. Similar fasteners and identical clamps are used here.

How to remove a panel on a Grant to install a radio

In most configurations it comes with a plastic plug instead of a tape recorder.

Next, you will need to reach into the resulting groove and find a standard terminal there for connecting a sound reproduction device. It needs to be taken out. After this, a short shaft is placed on the panel, intended for mounting a modern radio. At the end, the device is connected to the on-board network and inserted into the prepared shaft.

Installing the Euro trim without removing the dashboard

In this option, you need to have a drill and screws on hand.

Rely on the lining mounting diagram and start in order:

1. Remove the dashboard.
2. Open the glove compartment and unscrew the three screws from the inside (positions 1,2,3 in the diagram). Trying to unscrew the screw (pos. 9) from the inside near the windshield is difficult, but doable.
3. Remove the 4 keys (next to the control module) and unscrew the screws from the inside (pos. 4.5)
4. Unscrew or loosen the fastening by adjusting the backlight (pos.
5. Open the fuse module and unscrew 2 screws from the inside (pos. 6 and 7)
6. Now the panel overlay is held in place only by screws, positions 10 and 11. They cannot be unscrewed, so we break them out or lift the overlay by the right edge and cut them off with a file. (Note: the Euro trim will cover the entire top of the panel up to the windshield, so you don’t have to worry about the appearance when you cut or break the screws)
7. Remove the old dashboard trim.

Removal and installation of panel (dashboard) Grants

Removing the panel (dashboard) of Lada Granta

Required tools: flat and Phillips screwdrivers, 13" and 24" socket heads, marker.

Disconnect the negative cable from the battery. Remove the cigarette lighter (squeeze the lock and remove the cigarette lighter socket, disconnect the connector with wires). Remove the head unit of the audio system (radio tape recorder) and disconnect the block with wires from it.

Remove the central panel trim (dashboard). Remove the glove compartment cover and remove the screws securing the inner panel.

Remove the pillar trim. Then remove the central tunnel. Then remove the steering wheel. Remove the steering column cover and steering column switches. Remove the exterior lighting control unit (first remove the fuse box cover, then unscrew one screw and disconnect the connector.)

Remove the headlight hydraulic corrector regulator (remove the handle, unscrew the fastening nut, remove the hydraulic corrector regulator).

Remove the instrument cluster. Then... Remove the 4 screws securing the air duct damper control unit to the instrument panel. Remove the 18 screws securing the decorative panel to the frame (Figure 11.13). Move the decorative panel away from the frame as far as the air ducts attached to its inside allow.

Pull the panel towards you, and bending air duct No. 4 of the windshield, transfer it through box No. 2 (Fig. 12.1) for supplying air to the central deflectors on the heater body. Remove the decorative instrument panel.

• Remove air duct No. 4 (Fig. 11.14) of the windshield.
• Remove the two bracket nuts from the panel brackets.
• And move them to the air duct brackets - this will allow you to install the decorative panel in place without the air duct, and secure the air duct to the panel after its installation by screwing in the screws from the interior side.

Figure 11.13. Location of Lada Granta panel screws.

Figure 11.14. Decorative instrument panel (view from the inside):

Installation of panel (dashboard) Lada Granta

Installation of the dashboard is carried out in the reverse order, but a number of points should be taken into account: Before installing the panel, place the windshield air duct on the window of the heater housing.

After installing the panel, put the air duct brackets in place (for clarity, shown on the removed panel). Screw in the fastening screws from the passenger compartment side.

By the way, do you know how to paint a panel?

vazikov.ru

Removal and installation of the air duct damper control unit Lada Granta VAZ 2190

11 — temperature regulator damper drive cable.
Execution order

1. Remove the decorative instrument panel as described here.

2. Squeeze the clamp on the end of the air recirculation damper cable sheath and disconnect it from the holder (5) on the recirculation unit.

3. Press down on the locking tab and disengage the cable end from engaging the axle arm.

4. Similarly, disconnect the cable (11) from the temperature regulator damper.

5. Disconnect the cable (8) from the air distribution flap to the instrument panel vents and the driver and passenger footwell ducts.

6. Disconnect the cable (7) from the air distribution flap to the windshield deflectors and instrument panel deflectors.

Note:

Mark the location of the cables so that they can be installed in the same places during reassembly.

7. Remove the air duct damper control unit (10).

8. Install the air duct damper control unit in the reverse order of removal.

How to install and connect

To install a radio on Grant, you need:

1. Remove the decorative plug in the front panel by lifting it with a mounting spatula. Wires with ISO standard connectors are located in special routings on the back.
2. Place a 1 Din mounting shaft in the rectangular hole and press firmly.
3. Use a screwdriver or other object to bend the metal corners that will keep the part from falling out.
4. Open the glove box lid to find the antenna cable, which is located under the floor sound insulation near the front passenger's feet.
5. Connect the power adapter (depending on the type of head unit). Route the cables through the installation shaft.
6. Install the speakers in their original places. The doors of the basic configuration do not have cables for connection; there is only a connection plug located near the clutch pedal. In this case, the cables should be installed independently, passing them through the corrugated protective channels located between the stand and the door.
7. The laid wires are wrapped in foam rubber, which is secured with tape or insulating tape. This manipulation allows you to avoid extraneous sounds caused by the contact of cable insulation on the metal door panels.
8. When using speakers with a diameter of more than 13″, it is necessary to make wooden or plywood podiums that will allow the equipment to be installed in a standard hole.
9. Connect the plugs to the head unit, which is then inserted all the way into the mounting shaft.
10. Check the operation of the radio receiver and player in different modes.
11. Install the decorative frame in its original place.

To install a double-din head unit you need:

1. Using a mounting spatula, remove the air conditioner control knob.
2. Pry up and remove the plastic cover of the central part of the instrument panel. When dismantling, it is necessary to disconnect the wiring plugs to the control buttons for additional equipment.
3. Using a hacksaw and a construction knife, cut out the central jumper in the instrument panel. At the same time, the transition channel for the central interior ventilation deflectors is shortened by 4-5 mm.
4. Install the radio in the shaft using modified mounting brackets. The device is attached to standard points located in the instrument panel.
5. Mount the modified decorative frame onto which the deflectors have previously been rearranged.

If the head unit supports a low-frequency speaker, then a separate wiring is laid to it, which runs under the trim on the thresholds. When using an active subwoofer with a bass reflex, it is necessary to route the power cables, equipped with a separate fuse, into the luggage compartment.