Installation and operating instructions for Scher-Khan Magicar 9

Alarm Sherkhan 9, also known as Magicar 9, has been on the market since 2008. The system in question is equipped with the ability to autostart, and also has a turbo timer. True, the turbo timer works on the principle of “turn on the ignition after turning it off,” which is typical for many budget-class security systems. Otherwise, there can be no complaints about the Sherkhan 9 signaling system: neutral switching control is provided, and engine starting control is carried out using a tachometer. In addition, the signaling of the specified model can be connected to the CAN bus by selecting one of the firmwares with jumpers. These details are discussed in more detail below. Enjoy reading.

Alarm equipment

The alarm system for the Scher Khan Magicar car with engine start function includes the following elements:

• instructions for installation and use of machine alarms;
• main system control module;
• a remote control with a screen that has the option of dual communication and settings of some “signaling” functions;
• auxiliary remote control without display;
• sensitivity controller with wire;
• controller for calling the car owner from inside the car;
• antenna adapter;
• temperature controller, in accordance with the values ​​of which the power unit is started according to the specified temperature regime;
• car engine blocking relay with a connected block;
• siren;
• limit switches for mounting on the hood, trunk and doors;
• three six-pin plugs with cable and safety devices;
• eleven-pin connector for connection to the control module;
• six-wire cable for connecting the antenna adapter;
• two-wire cable for connecting additional channels;
• four-wire cable for connecting to the CAN bus, its use is relevant if there is a CAN output in the car;
• stickers for fixing the call controller and antenna adapter.

Car alarm Scher-Khan Magicar 9.

The signal reception range of the Scher-Khan Magicar 9 alarm system is 2000 meters, like most models produced in 2009.

The distance for operating the equipment within the city is more than enough. The reception quality is stable, screens and obstacles do not interfere.

Sherkhan Magikar 9 is designed for installation on vehicles equipped with a CAN bus.

Unfortunately, this model has been discontinued from mass production, but qualified support from dealership specialists is still ongoing. If you need preventive maintenance or repairs, you can always contact certified technical centers.

Specifications

What are the characteristics of Sherhan machine alarms:

• to protect against pulse interception, the manufacturer’s own Magic Code Pro 2 system is used;
• to confirm that the protective mode is disabled, an additional code is used;
• the range of the main key fob with the central module is up to two kilometers, but only if the area is open;
• it is possible to protect the system from unauthorized configuration of spare remote controls;
• The direction of the anti-theft system is two-way.

User L1DER showed how to hack the Sherkhan alarm system.

Video

PROMOTION: SALE OF NEW CAR 2022 PRODUCTION

Alarm Sherkhan 9, the operating instructions for which will be given below, is a full-fledged anti-theft complex. The system is equipped with an expanded set of functions that facilitate control and protect the car from theft. There is an automatic engine start that helps prepare the vehicle for the trip.

Main functions

Signaling options:

1. Possibility of turning on the protective mode when the engine is running.
2. “Turbo” option, designed to maintain the operation of the power unit in the range from one to four minutes.
3. The “Hands Free” option is designed to automatically activate and deactivate the protective mode.
4. Availability of “Panic” and “JackStop” functions. Used in case of danger or when necessary to draw attention to the vehicle through sound and light signals.
5. The Pit Stop function provides additional comfort during short stops. The car owner can arm the car with the power unit running without a key in the lock.
6. “Slave” mode. Its presence allows you to use the standard machine control panel to configure certain options.
7. Hidden security function. When activated, if the “alarm” is triggered, the pulse will be transmitted to the main control panel. The siren will not be activated.
8. Possibility of remote start of the machine motor with indication of the time of its operation. The time interval can be adjusted down to seconds.
9. Option for remote engine start using a timer; this option can be activated on vehicles with automatic and manual transmission.
10. There is an option to start the engine by command from the remote control, temperature, or as a result of the battery charge dropping to a limit below 11.5 Volts.
11. Availability of a personal code to gain access to the car interior if the key is lost.
12. There is a delay function for turning off the lights in the car interior; up to three modes can be configured.

Advantages and disadvantages

According to reviews, the following advantages can be identified:

1. Availability of two-way communication. Thanks to this, the car owner can always know what condition the car is in. But only taking into account the fact that the remote control is within the range of the “signal”. The device shows whether the security mode is activated and which zones of the anti-theft system were activated if the siren was activated.
2. Remote motor start option. Particularly relevant in the winter season or if the driver is in a hurry.
3. Effective vehicle protection. Technologies that are used to protect code from interception make it possible to ensure reliable security of the machine.
4. Extensive functionality that allows you to customize the anti-theft installation to suit your needs and requirements.
5. A detailed installation and use manual will allow the car owner to independently install the system and configure it.

An overview of the system from user Pavel Korshunov is presented in the video.

Flaws:

1. Consumers note that the “Slave” mode is actually useless. When the turbo timer is operating, the car remains running; in this case, the buttons on the door handles do not work. This means that closing the machine is impossible. The car owner needs to lock the vehicle using the remote control.
2. The system control panel is large in size. If you are accustomed to a tag key and the fact that to open the car you do not need to perform any actions, but only approach it, then you will not like the large Sherkhan keychain.
3. To activate the turbo timer option or automatic engine start, the handbrake must be activated in advance in the car. Some consumers consider this a disadvantage. Although, this is a feature of the option.

Not programmable: reasons

The remote control began to work incorrectly. You decided to reprogram it yourself. Before doing this, do a few simple steps.

1. Find the instructions for the anti-theft system installed on your car.
2. Study the procedure carefully.
3. If there is no documentation, then try to find information on the Internet.

You have done all the steps according to the instruction manual, but the key fob does not work. It is not possible to flash the pager due to:

• damage to the communicator;
• random activation of the “Jack” mode;
• control module failure.

Installation Guide

For installation, prepare the following tools and materials:

1. Multimeter. We recommend using an electronic device; pointer testers give less accurate readings.
2. Wiring for connecting the “signaling”. The alarm kit comes with wires, but we recommend additionally preparing a set of cables for installation. Standard wiring may not hold up.
3. A piece of foam rubber, preferably dark in color. Required for packaging the control module of the anti-theft system.
4. Insulating tape.
5. Double-sided tape.
6. Phillips head screwdriver.
7. Stationery knife.
8. Socket wrench.

How to install the Sherkhan Magikar 9 system:

1. First of all, the location for mounting the central module is determined. The control unit must be installed so that an attacker cannot reach it. For example, behind the glove compartment or dashboard. You can also disassemble the facing part of the center console and hide the device behind the control panel if there is free space. Before installation, the unit should be wrapped in foam rubber to hide it and also to prevent damage to the module due to exposure to moisture or elevated temperatures. The device is fixed with self-tapping screws. It is important that it is not affected by vibrations, otherwise the unit may fail.
2. It is better to use the engine compartment to install the siren. It is necessary to select a place for installation so that the siren is as far as possible from the cylinder block. When installing, the siren horn should be turned to the side or in the direction of travel of the car, the main thing is that it does not look down.
3. The temperature sensor is installed in the engine compartment. The device is installed in the cooling system pipe. The sensor cannot be placed in close proximity to the collector, otherwise it will quickly fail due to exposure to elevated temperatures. Securely fix the controller.
4. The shock sensor is mounted inside the car. Experts recommend installing the device on the partition between the passenger compartment and the engine compartment. At this point, the sensor will be able to record all the impacts that occur on the car body. The controller is fixed to a metal surface; plastic parts cannot be used for fastening. Plastic is a more sensitive material than metal, so it will more often transmit vibrations that activate the sensor. In addition, when heated, plastic expands. And this also contributes to the operation of the controller.
5. An antenna adapter should be placed on the inside of the windshield. The transceiver should be installed away from metal components of the body. The presence of metal near the adapter within a radius of 5 centimeters will cause interference and reduce the accuracy of signal transmission. There will be difficulties with setting and disabling the security mode.
6. The LED indicator is installed in the area of ​​the glass so that when it turns on, you can understand that the car is under protection without going close to it. The operation of the diode element can frighten potential attackers.
7. Limit switches are installed on the hood, doors and trunk. To do this, you will have to dismantle the facing elements on the doors and trunk. Handles, speakers, trim are removed. After installing the switches, the contacts from them are led out into the interior.
8. The final stage of installation will be laying the wiring. Electrical circuits are laid under the interior trim elements; there should be no moving elements at their location. From the engine compartment, the wires are pulled into the passenger compartment through a technological hole in the partition. All components of the anti-theft installation are connected to the central unit.

Install the central unit

Install the siren in the engine compartment

Lay out the wires and connect them to the module

Safety precautions

To prevent problems from occurring, it is necessary to take into account the nuances of safety precautions.

All connection and installation work must be carried out with the battery disconnected. Otherwise, a short circuit may occur, which will lead to damage and even failure of the alarm components. Do not connect wires unless you are sure you are doing it correctly.

Installation and connection diagram

The connection procedure is carried out in accordance with the electrical diagram included in the kit. If you have never performed such a task before, it is best to leave the connection to a qualified electrician.

Installation and connection diagram – 1

Installation and connection diagram – 2

The connection procedure is carried out in accordance with the electrical diagram included in the kit. If you have never performed such a task before, it is best to leave the connection to a qualified electrician.

User manual

The package includes an instruction manual, which describes all the nuances of operation. Let's look at the main points.

Modes

Features of the “signaling” operating modes:

1. Pressing key 1 for 0.5 seconds will activate the protection function, turn off the alarm, close the locks, and also block the starter mechanism.
2. To disable the security mode and alarm, click on button 2. This will deactivate the locking of the starter device and open the door locks.
3. Pressing key 3 will activate the screen backlight.
4. A short click on button 4 will allow you to diagnose the state of the anti-theft installation.
5. To turn on the “Panic” mode, the car owner needs to hold down button 1 for two seconds.
6. To remotely turn on and off the car’s engine, as well as to intercept the ignition when the “Pit Stop” mode is activated, button 2 is pressed for two seconds.
7. If you hold down key 3 for two seconds, the luggage compartment of the car will open. The first channel is controlled by pressing button 4 for two seconds.
8. To activate or deactivate the siren signal, you must simultaneously click on buttons 1 and 2.
9. Enabling and disabling the “Jack” function is carried out by simultaneously pressing keys 1 and 3.
10. To activate and deactivate the kick controller, press buttons 1 and 4 simultaneously.
11. By pressing keys 2 and 3, you can enter the control mode for the second additional channel.
12. You can activate and deactivate the timer for remote start of the internal combustion engine by simultaneously clicking on keys 2 and 4.
13. To activate and deactivate the keypad lock on the remote control, you need to hold down buttons 3 and 4.
14. To enter the remote control options programming mode, press buttons 1 and 3 for two seconds.
15. Activation of the “Hands-free” mode is carried out by simultaneously pressing keys 2 and 3.
16. To manually reserve the ignition start function when the “Turbo” option is turned on, you need to briefly press button 2 twice within one second. This option is only possible with manual transmissions.

Setting up the key fob

In order to use the key fob to turn the engine on and off, as well as perform other functions, it must be programmed into the device’s memory:

1. When the engine is turned off, the ignition is activated. Then the call key is pressed for two seconds. The turning lights should blink once.
2. Within five seconds, you need to briefly click on the key fob call button. The turn lights will flash twice if no personal password is used. If it is activated, the warning light will blink once.
3. If you have set a password for management and configuration, then at the next stage you need to specify its value. The turning lights will blink twice.
4. After five seconds, the LED indicator should blink blue. This indicates that the system is ready to program remote controls.
5. Within five seconds, briefly press key 1 on the remote control. If the system has accepted the code, the emergency light will blink once. The procedure is repeated in a similar way for an additional key fob. If the system accepts the remote control, the turn lights will blink once.
6. You can leave setup mode at any time. To do this, simply do not perform any actions for four seconds. Exit from this mode will be indicated by one long siren signal.

The scherkhan5 channel showed how the Sherkhan Magikar 9 anti-theft installation reacts to an attempt to intercept the code by a code grabber.

Programming functions using a key fob

The options are configured as follows:

1. To start the setup mode, press buttons 1 and 3 simultaneously for two seconds. “Pr o9” will appear on the key fob display and a melodic signal will sound.
2. The user is automatically taken to the time setting menu. To change the hour, use key 1, to change the minutes, press button 2.
3. To start the engine on time, press button 4. The set time readings will start blinking on the remote control display. Button 1 changes the hours, and button 2 changes the minutes.
4. To set the alarm activation time, the user presses button 4 again. In the same way, by pressing keys 1 and 2, the alarm clock is set to start the internal combustion engine.
5. To turn off or activate the alarm, press button 4 again. The clock-shaped indicator on the key fob display will begin to blink. Using button 1 you can set whether to activate or deactivate the device.
6. The next press of key 4 will take you to the menu for disabling and activating the option to call the car owner. A handset-shaped indicator will flash on the remote control screen. Key 1 enables or disables the function.
7. After pressing key 4 again, the user will be transferred to the section for activating and disabling the vibration of the remote control. The screen will display an indicator in the form of a vibrating key fob, as well as the current status of the option. With key 1 you can disable or enable the function.
8. The next time you press button 4, you will enter the menu for changing the temperature display format. Degrees can be displayed in Celsius or Fahrenheit. The indicator that corresponds to the set temperature format will blink on the remote control screen. By pressing button 1, you can change the format sequentially.
9. To change the time display format (12 or 24 hours), button 4 of the remote control is pressed again. The indicator that corresponds to the currently set format will flash on the display. If you press button 1 of the key fob, you can change it.
10. Pressing key 4 again will activate the menu for enabling and disabling the “Battery Saver” option. A battery symbol will appear on the display and the current status of the option will also be shown. The mode is changed by pressing key 1.
11. To leave the options programming mode, press buttons 1 and 3 on the remote control simultaneously. The device goes into the anti-theft installation control mode.

The AvtoGSM channel demonstrated the operation of the Sherkhan Magikar 9 anti-theft installation.

How to enable autorun

You can set the car alarm to autostart by briefly pressing the combination of keys II and IV. The appearance of TIMER will inform the car owner that the function has been successfully activated.

There are four possible options:

1. The car will turn on the engine every day at the set auto start time.
2. The power unit will start periodically every eight hours.
3. Similar to the second mode, but the cycle is 4 hours.
4. Starts every two hours.

To set autorun by timer, you must follow the instructions in the table below.

Sherkhan 9 supports autostart based on temperature or on-board network voltage. To do this, you need to enter the programmable functions menu using buttons I and IV. The user will have the opportunity to select one of the temperature values, which is the most optimal in a given situation.

Possible faults

What problems can a car owner encounter:

1. The engine does not start when the autostart function is turned on. Diagnostics will help you find out why this happens. First, check if the remote start feature is enabled. The option to start the internal combustion engine based on temperature may be activated. If the difference between the readings of the thermometer and the temperature sensor is at least one degree, the system will not start the engine.
2. The alarm doesn't work. If you cannot enable or disable the security mode, first of all the condition of the battery in the key fob is diagnosed. When the battery is dead, it must be replaced. You can tell when the battery is low by reducing the range of signal reception and transmission. Try to approach the car close to the side where the antenna adapter is installed and press the key fob button. If the “alarm” does not work, change the battery. When the battery is normal, you need to disassemble the key fob and assess its condition. If there are traces of moisture, the device must be dried, but it should not be left under prolonged exposure to high temperatures. You also need to check the condition of the transceiver. Practice shows that damage to the contacts on its connector or broken wires most often contribute to such problems.
3. The alarm goes off for no reason. This error may be due to incorrect operation of the control module or incorrect settings of the shock sensor. First, we recommend adjusting the sensitivity controller. Usually such problems are associated with it. Make sure the sensor is securely fixed in its installation location. If this is the case, then the control module is checked. It is necessary to diagnose its connectors and contacts. If the plug is oxidized, the contacts must be cleaned. We recommend dismantling the unit and disassembling it. When there are traces of moisture or damage on the module, the device must be repaired. Moisture must be carefully removed with a napkin. If liquid gets on the board, it is better to leave it for a while near a battery or other heat source.
4. The security mode does not turn off, the car engine is blocked and will not start. The reason should be sought in the control unit. Water could get on it, causing the device to malfunction.

For what reasons may the automatic start of the internal combustion engine not work:

• the engine has already started, the warning light will blink once, and the key fob display will display error code 01;
• the ignition in the car is activated, the hazard warning lights will blink twice, the fault code on the remote control is 02;
• The car door is not locked, error 03, the car's turning lights will blink three times;
• autostart will not be possible if the trunk door or hood is open, the warning light will blink four times, the fault code is 04;
• another reason - the car owner has not completed the start reservation procedure for a manual transmission, the turning lights will blink five times, the fault combination is 05;
• The handbrake lever is turned off, error code 06, the warning light will blink six times;
• remote start of the power unit will be impossible when the brake pedal is depressed, the key fob display will display fault code 07, the turning lights will blink seven times;
• if the reason lies in the engine itself (malfunction of the power unit or ignition system), then the error code on the remote control screen will be 08, and the turning lights will blink 8 times.

Independently performing any repair work related to the alarm system is only possible if the system’s warranty period has expired.

Scher Khan Magicar 9 car alarm malfunctions and how to fix them