Lada Vesta key - instructions for use

In modern cars, the ignition key also has buttons. It has its own battery and needs to be changed. One of the Lada Vesta devices is a three-button engine ignition control panel with a flip key. On the Lada Vesta, the key controls the central locking, as well as the locking device of the luggage compartment. Since it is a flip key, it means it needs a special case, read our article in detail about this device!

Replacing the battery on a Mercedes key. disassemble the fish key and change the battery

For Lada Vesta/XRAY: open the key body by unsnapping the latches around the perimeter using a thin slotted screwdriver.
For Lada Largus: unscrew the fastening screw (Phillips screwdriver), and then open the key body, unclicking the latches around the perimeter using a thin slotted screwdriver.

For Lada Priora/Kalina/Granta: unscrew the fastening screw (Phillips screwdriver), and then open the key body, unclicking the latches around the perimeter using a thin slotted screwdriver.

The process is also shown in the video:

Let us remind you that if after replacing the battery the standard alarm still does not work, read these instructions. By the way, do you know how to make a flip key for a Lada yourself?

Lada Vesta key - instructions for use

In modern cars, the ignition key also has buttons. It has its own battery and needs to be changed. One of the Lada Vesta devices is a three-button engine ignition control panel with a flip key. On the Lada Vesta, the key controls the central locking, as well as the locking device of the luggage compartment. Since it is a flip key, it means it needs a special case, read our article in detail about this device!

Cases

The plastic body of the control panel is fragile, like other switchblade bollards.
If dropped from human height, the ignition control panel may break. A special case for the Lada Vesta key can save the remote control from scratches and damage. The case for the remote control is a silicone shell of different colors (green, red, orange, yellow, blue, transparent, black). The rubber of the cover is soft; upon impact, it absorbs the kinetic energy of contact. At the same time, the presence of the shell does not affect keypresses in any way.

There are many manufacturers and stores where you can buy such a case. You need to look for a department with car accessories or place an online order. The price is small - from 100 to 300 rubles.

A modern ignition control panel is a convenient device that gives respectability to the owner. If you treat it with care - protect the case from damage, replace batteries on time, do not ignore existing problems - it will serve you for a long time and reliably.

How to lock a Lada Vesta with a key

You can't just lock a car with central locking using a key. The lock cylinder is located only on the driver's side, the remaining openings are closed centrally. You should be able to perform a simple manipulation, which we will describe below:

Open the driver's door; Find on the center console in the cabin a button with a picture of a door and a key (above the interior temperature controls); Press this key for five seconds (a single press will lock the doors for a short period of time due to the fact that the driver's door is open); Make sure that all doors are locked; Leave the car, close the driver's door mechanically. Where can I get a spare key?

This is where the spare tip tag comes in handy. It is by the number engraved on this sticker that your dealership selects the appropriate opening element. Not only will the tip be made, but the remote control itself will be coded according to your system. For Lada Vesta you can choose several different ignition control panels. Therefore, you can order yourself a new DPU without losing your regular one.

Please note that Lada vesta opening devices may be different. Depending on the vehicle’s configuration, you can see forms ranging from a regular mechanical key to a folding key with DPU. The variety of types suggests the ability to make spare keys yourself or contact any key master. In order to make a new kit, you need:

Purchase a blank for a specific Lada vesta model (otherwise the size will not fit); Copy the tip pattern (by removing it from the body or removing it from the mount); Program the chip to synchronize with your alarm system.

Where to get a spare key

If you need to manufacture, purchase, or duplicate a Lada Vesta flip key, you need to know the number with the code that is engraved on the tag. Using this number, the dealer organization determines the appropriate kit. Some models allow the use of three or four remote controls. You can buy a Lada Vesta key at car dealerships or online stores.

In accordance with the modification and equipment of the car, the Lada Vesta key has a different shape (from the simplest to the modern folding one).

Based on this, it is possible to do it yourself.

• There are blanks available on the market. You need to know the car model, otherwise the board will not fit in size;
• The second stage will be copying the tip. If excluding the fasteners from the body is not enough, the product itself is disassembled, and then the blade of the Lada Vesta ignition key is sharpened;
• Finally, to complete the work, the chip in contact with the alarm should be programmed. Craftsmen who know how to operate a soldering iron have no problem performing such an operation.

Using a spare

When faced with a breakdown or loss of the main remote control for the first time, the car owner will not immediately understand how to open the Lada Vesta with a spare key and without a key fob.

Vesta key. Photo source: https://www.drive2.ru/l/9164898/

To do this, you need to pry up and remove the plug on the driver's door handle that hides the lock hole. Through it you can mechanically open the car.

Types of ignition keys for Lada cars

When purchasing a Lada, you will notice that it comes with a set of keys, each of which has a specific function. If everything is clear with the key for opening the trunk and doors, then it is difficult to determine why two identical ignition keys are needed at first glance. The fact is that one of them is working, and the second is training.

If a working ignition key is lost or broken, the service will require a training element. Its distinctive features are the absence of buttons, small size and a red insert at the top end.

Photo source: https://ok.ru/ladaxrey/topic/70651220732748

Working and educational devices differ not only in appearance, but also in functionality. When red is inserted into the ignition switch, the immobilizer starts flashing. This is how the machine shows that it is ready to retrain a new blank.

How to disassemble a Lada key

For Lada Vesta/XRAY: open the key body by unsnapping the latches around the perimeter using a thin slotted screwdriver.

For Lada Largus: unscrew the fastening screw (Phillips screwdriver), and then open the key body, unclicking the latches around the perimeter using a thin slotted screwdriver.

For Lada Priora/Kalina/Granta: unscrew the fastening screw (Phillips screwdriver), and then open the key body, unclicking the latches around the perimeter using a thin slotted screwdriver.

The process is also shown in the video:

Let us remind you that if after replacing the battery the standard alarm still does not work, read these instructions. By the way, do you know how to make a flip key for a Lada yourself?

LADA VESTA. ELECTRICAL EQUIPMENT OF THE LADA VEST A - REMOVAL / INSTALLATION OF MAIN UNITS AND PARTS

1 GENERAL DESCRIPTION OF THE SYSTEM, DEVICE AND OPERATION FEATURES

The electrical equipment is made according to a single-wire circuit - the negative terminals of sources and consumers of electricity are connected to the car body, which acts as a second wire. Rated voltage 12 V.

The vehicle's main power circuits are protected by fuses. Before replacing a blown fuse, it is necessary to find out the cause of its blown and eliminate it.

Attention! When repairing a vehicle or electrical system, it is necessary to disconnect the earth wire terminal from the battery.

When operating a vehicle and when checking the electrical circuit of the vehicle, it is not allowed to use fuses that are not provided for by the design of the vehicle.

LADA VESTA.
BATTERY – REMOVAL / INSTALLATION Removal
Place the car in a working place, apply the parking brake, turn off the ignition, raise the hood.

Before disconnecting the terminals from the battery terminals, you must:

– wait until the electric fan of the engine cooling system stops;

– wait until the end of the data saving procedure in the ECU (1 min).

Do not remove the terminals from the battery terminals while the ignition is on, as this may cause errors in the ECM or lead to failure of electrical components.

The reliability of the visual battery status indicator is not guaranteed by after-sales service, so the visual indicator should not be used as a means of monitoring battery status.

Loosen the tightening of nut 7, Figure 2-1, of the bolt securing the battery ground wire terminal (wrench 10).

Disconnect terminal 6 of the ground wire from battery 8.

Remove the cover of the 3rd positive terminal.

Loosen the nut 1 of the bolt securing the terminal of the positive wire of the battery (spanner 10).

Figure 2-1 – Installing the battery on a car:

Electrics, sensors, battery Lada Vesta

Products from the Dustershop77 range on the topic of the article:

How to open a Lada Vesta with just a key

To open the car door in a way that is suitable when the battery is charged, you need to remove the cap on the right side of the driver's handle, which looks like a regular one. It is necessary to open the plug in a specific slot using a suitable object. The cap, under which the lock is located, fits tightly and cannot be removed with bare hands.

Knowing how to open Vesta without keys, the car owner can save nerves and time. Repeating the entire procedure with the plug, on a car with a dead battery, you need to replace it or charge it. If there is no power for the battery, you need to find a groove on any of the door handles except the driver's. It will open using the control panel.

How to determine if the battery is dead

For Lada Vesta, Largus and XRAY cars. If the clarity and range of the remote control decreases, the battery must be replaced.

For Lada Priora, Granta and Kalina cars. If the supply voltage of the remote control is within normal limits, then each time you press any button on the remote control, the indicator lights up with a short flash. If it lights up with two short flashes or does not light up at all, then the battery should be replaced.

How to change the battery in the Lada Vesta ignition key

Buttons consume energy, so you need to remember the battery charge and change it in time. The first sign of low battery will be a slow response when pressed. The Lada Vesta flip key is synchronized with a standard battery. To change it you need a screwdriver. The remote control opens with the blade extended, otherwise the case and microcircuits can be damaged. The tool is inserted into the hole in the center line of the case and with a simple movement separates the remote control into two halves. After changing the battery, you need to use a light snapping motion to assemble the product.

How to change the battery in the key

Replacing the battery in a Lada car key

Some configurations of Lada cars (XRAY, Vesta, Largus, Granta, Kalina or Priora) can use an ignition key with a built-in remote control (factory alarm), which controls the central locking. If it stops working, first try changing the battery.

Types of ignition keys for Lada cars

How to determine if the battery is dead

For Lada Vesta, Largus and XRAY cars. If the clarity and range of the remote control decreases, the battery must be replaced.

For Lada Priora, Granta and Kalina cars. If the supply voltage of the remote control is within normal limits, then each time you press any button on the remote control, the indicator lights up with a short flash. If it lights up with two short flashes or does not light up at all, then the battery should be replaced.

How to disassemble a Lada key

For Lada Vesta/XRAY: open the key body by unsnapping the latches around the perimeter using a thin slotted screwdriver.

For Lada Largus: unscrew the fastening screw (Phillips screwdriver), and then open the key body, unclicking the latches around the perimeter using a thin slotted screwdriver.

For Lada Priora/Kalina/Granta: unscrew the fastening screw (Phillips screwdriver), and then open the key body, unclicking the latches around the perimeter using a thin slotted screwdriver.

The process is also shown in the video:

Let us remind you that if after replacing the battery the standard alarm still does not work, read these instructions. By the way, do you know how to make a flip key for a Lada yourself?

Topic: Second switch

Theme Options

• print version
• Send by email...

• Search by topic

  Display

  Linear view

• Combined view
• Tree view

not very smart and meet with OD..

I have no doubt this happens! And sometimes it’s not that they are “not smart”, but they are sincerely mistaken.

But is there any other information? Maybe a link to the hardware part?

So it seems that the instructions about this key have everything. In short, it's a regular spare key. It has the same as the main built-in immobilizer, but to save a penny, it does not have buttons