How to disable the turbo timer on Starline a91 • AUTORUSERVIS.RU

Using a turbo timer on the Starline A93 and other models allows you to prevent rapid wear of the car’s engine, ensuring it idles after the ignition is turned off. The design of such a device makes it possible to install it both on cars with a standard lock and on vehicles equipped with a Start/Stop button. The principle of activating the option is to press the key fob buttons or the service mode key several times during certain events (stopping the engine, turning on the ignition system).

Download installation instructions for Starline alarm systems for different models in PDF format

You can download service controls for the option and control of StarLine car alarms using the following links:

Disabling the turbo timer on the A9 model

For this type of signaling, the function is disabled in programming mode:

Start the car.
Press the service button 6 times.
Turn off the engine. The siren should sound 6 times.
Press the service button 16 times.
Within 10 seconds, you must press button 1. Proof of your choice is 1 signal from the siren and key fob.
After the option – turn on the ignition.

Turning on the turbo timer on models B9, A91

Press button 3 until 2 beeps sound.
One of the icons in the bottom row will be highlighted with the cursor. Use button 3 to select “EXTRA RUN”.
Press button 1. The car's dimensions will flash 1 time, the key fob will emit 3 beeps: 2 small and 1 long.
“EXTRA RUN” will constantly glow on the screen.

If the turbo timer mode is turned on, it is activated by pressing button 2. In this case, the car must be started and the doors closed. After turning off the ignition, the engine remains running for the programmed time.

Photo gallery

Disarming without confirmation beeps

How to properly configure the Starline alarm key fob?

Silent disarming of the security system, during which no sound indication (siren) will be used, is performed in one of the following ways:

triple pressing the key fob button;
SMS command 101;
command 101 from the voice menu;
from the StarLine mobile application;

The complex will confirm successful disabling of security with 2 light signals. If the “Alarm” mode was activated during security, 3 light signals will follow.

After turning off the security of the complex, all events that occurred during the security period will be displayed on the key fob screen.

How to install?

Connect the 2nd additional channel, which is used to control the turbo timer.
To set the timer, you need to connect the red-yellow contact located on block X3 to the control module. When the function is turned on, a grounding occurs on this cable, with the help of which the ignition maintenance relay is activated or the Start/Stop pulse is duplicated.
If you need to additionally install a motor blocker bypass, it must be connected to the pink contact on connector X3.

Starline turbo timer connection diagram

Principle of operation

The principle of operation of the turbo timer on car security systems B92, B94, A 39, A61 and other versions:

Thanks to the use of the device, the driver will be able to turn off the ignition system and leave the car with the engine running. At this moment, you can turn on the security mode, while the engine will idle for some time.
While the engine is running at idle speed, air continues to circulate inside the turbocharged unit, which allows the device to cool.
After the motor temperature drops or the timer expires, the unit will stop.

READ 2022 Renault Duster Oroch with modern design elements

How to turn on the turbo timer?

The countdown timer on an automatic or manual transmission can be activated automatically or by command.

Varieties

Autonomous systems. Such devices are manufactured in the form of a module mounted on or under the center console of the car. The unit is purchased as an addition to the anti-theft system and is connected using programmable channels. The alarm key fob has buttons that allow you to set the turbo timer and control the system.
Built-in. Such turbo timers are built into the control unit of the security complex and are considered an additional option. The module is installed hidden under the center console.

Programming and configuration on A93, A63 and E91

Function programming and setting guide (suitable for A6, A62, A63, A93 Eco):

The cursor is placed on the “TURBO” icon.
The first button is briefly “clicked”, followed by 1 light signal. The key fob will emit 1 melodic signal for 4 seconds. The current value of the turbo timer operating time will be displayed.
Using the first key, you can set the required operating time of the function, the maximum value is 6 minutes. One press of the button corresponds to a step of 1 minute.
To save the settings, you need to hold down the first key. The communicator should give one short beep, the Turbo indicator should remain lit on the screen. The option is configured in a similar way on models E60, E61, E90.

Identification of buttons on the Starline A93 remote control

Varieties

There are 2 modifications of the device mounted on cars:

Self-contained unit equipped with a separate microprocessor. The product is connected via additional channels to a previously installed alarm system or integrated into a standard security system.
A device implemented in software in a security system. A control panel with a display is used for setup and control.

Device selection

Before starting installation, you need to decide on the manufacturer of the turbo timer. The following performed best on the market:

The equipment is also important. For example, by purchasing an alarm system with a Starline or Magicar turbo timer, a car owner can expect to receive:

Control block;
a display that displays the time before the engine turns off and helps to configure the turbo timer;

Most turbo timers are installed under the dashboard. This is done not only for aesthetic purposes, but also to hide the device from prying eyes, since it has an alarm function. If there is a pre-installed security system, this criterion is not so relevant.

Principle of operation

The turbo timer provides support for the operation of a gasoline or diesel car engine at idle speed after removing the key from the lock. The reduced rotation speed ensures a smooth decrease in the temperature of the turbine housing and exhaust manifold, increasing the service life of the unit. Additional cooling is provided by circulating liquid. The owner of the car sets the operating time of the power plant during setup. After the timer is reset, the engine is turned off, and the ignition support circuits are included in the security zone.

Feasibility of installation

It is most advisable to install a turbo timer in the following cases:

A turbocharged diesel engine is installed in an all-terrain vehicle, primarily used in off-road applications. The operating mode is predominantly harsh. Often you have to drive with the maximum permissible load and with no cooling by the oncoming air flow;
The decision to install a turbine on an atmospheric engine was made independently.

Installing a turbo timer seems less relevant in the following cases:

Gasoline or diesel engines are used in a gentle mode. Movement occurs mainly around the city. The driving style is far from dynamic. Before stopping, the speed rarely exceeds 2000. The power plant uses high-quality oil;
The car already has a car alarm with a turbo timer, for example, Starline. Installing an additional device will be unnecessary;
The car is under warranty and installing additional equipment will lead to its loss. In this case, you need to get advice from a car dealership about the possibility of installing the device.

Whether to install a turbo timer or not is a personal matter for the owner. Much depends not only on the mode of operation of the iron horse, but also on the workload of the car enthusiast. It should be taken into account that even after installation, it is possible to disable the turbo timer, allowing you to use the machine in the previous mode.

How to disable the turbo timer on the Starline A93 alarm system

When installing a Starline on a car equipped with a supercharged engine, the owner needs to know what a turbo timer . The design of the device allows you to adjust the engine operating time without using a key. The driver of the car can forcibly turn off the turbo timer on the Starline A93, since some power plants have electric pumps that maintain coolant circulation after the engine is stopped.

How to setup

To program the engine operating time in turbo timer mode on the A91 alarm system, you must enter the complex setup mode by pressing the special button 6 times. After activating the ignition support circuits, the siren will sound 6 times, indicating that the alarm is ready for configuration. The driver selects the function by pressing the setting button once. After the siren gives a signal and the control diode flashes, the value of the motor operating time is selected, the programmed parameter is shown on the display.

The Starline A93 turbo timer is configured immediately after turning on the “turbo” icon; short presses on the red key allow you to change the operating time in a circle. Once the desired parameter has been configured, the value must be written to memory. The process ends automatically if the owner does not operate the buttons for 4 seconds. Forced recording is allowed by holding down the round button on the remote control. After the beep sounds, the key is released.

READ Disable passenger airbag Ford Focus 3

Possible problems

If you have problems activating the mode, you need to check the condition of the limit switch under the parking brake lever or button. If an element or wiring harness is damaged, the central unit blocks engine operation after turning the key in the lock. On cars with automatic transmission, turbo timer malfunctions occur when the sensor in the gearbox selector breaks down.

If a generator is used to control the operation of the power unit, it is important to maintain the correct polarity of the signal. In case of erroneous switching, the security system does not provide ignition support at the moment the key is removed from the lock. Problems also arise when the signal in the tachometer sensor circuit is not strong enough.

How to install

When installing equipment of the A91 modification, it is necessary to correctly connect the electrical wiring harness of the complex. The cable, equipped with a pink insulator, serves as an output for bypassing the blocking circuits of the power unit. Then you need to set the engine operating time; the equipment provides ignition support in a time interval from 1 to 6 minutes (depending on the modification of the complex).

On model A93 complexes, it is allowed to use a turbo timer when the automatic engine start function is disabled. To control operation, a machine generator or a signal cable going to the tachometer is used. Then you need to establish positive voltage support at the ignition switch terminals. If the car is equipped with a start button, then a negative control pulse is sent to the device. The parameter is configured by programming the output in plug X3.

How to disable

The car owner turns off the turbo mode by selecting the mode icon on the display using the cursor method. After the turbo timer on the alarm is turned off, the icon with the inscription “turbo” goes off on the screen. The programmed time is stored in the memory of the central unit of the complex, allowing the function to be used when the mode is reactivated. to completely remove the turbo timer from the Starline .

Starting the engine on an alarm clock

When this function is activated, the car engine will automatically start at the specified time. To activate the function, perform the following steps:

The key fob cursor is moved to the icon with the image of a clock and the button is briefly pressed. after which the car emits one light signal, and the key fob emits one melodic sound;
the key fob display shows the time after which the engine will automatically start according to the alarm clock;
after 5 sec. The current time display on the key fob resumes.

The engine autostart function using an alarm clock is activated for one start cycle. The fact that the mode has been successfully enabled is indicated by active icons depicting a clock and a bell on the key fob display.

Starline alarm system: auto start from key fob and automatically

The Starline autostart system provides an option for intelligent engine start, when the alarm system independently selects a frequency for communication between the main unit in the car and the key fob.

Thanks to such features, intercepting a security system signal is almost impossible. This is especially important in urban environments and conditions with high levels of radio interference.

Methods for starting a car’s internal combustion engine:

remote start (warming up the car before driving);
automatic start (periodic starting of the car engine at certain time intervals to maintain the temperature at a given value).

Remote autostart Starline

Before considering how to enable autorun on Starline, you need to pay attention to some features. To correctly configure autorun from the key fob, you must perform the following steps:

move the gearbox lever to the “neutral” position (all gears are disabled);
turn the key in the ignition and remove it from the lock (the car engine is turned off);
close the doors, trunk lid and hood of the car tightly;
turn on the parking brake (handbrake).

Fulfilling all these conditions allows you to start the car’s internal combustion engine remotely. Now let's move on to how to enable autostart on the Starline alarm system. First of all, to set the car in security mode with the “Starline autostart” function enabled, you must perform the following algorithm of actions:

stop the car moving without turning off the ignition (the car engine is running);
move the gear shift lever to the “neutral” position (gears are off);
put the car on the handbrake (parking brake on);
Press button “1” on the key fob and hold it for 3 seconds until a melodic sound signal appears;
turn the key in the ignition switch and remove it from the lock (the car engine does not stall);
when leaving the car, make sure that the doors, luggage compartment and hood are closed tightly;
if everything is done correctly, the alarm will turn off the engine and lock the car doors (security mode is on).

So, remote autostart on Starline is available with proper preparation of the car. Following the entire algorithm described above, the car can be started from the key fob in different ways:

the first method is to press button “1” and hold it for 3 seconds until a sound signal appears and quickly press button “3”;
the second method is to select the “START” icon and press button “2” (relevant for periodically warming up the engine in the winter).

Due to the actions taken with the key fob:

the alarm makes the first attempt to start the car engine;
if the car engine does not start on the first try, the alarm makes a second, third or fourth attempt (the starter operating time increases by 0.2 seconds each time);
if the car engine does not start after the fourth attempt, the key fob will sound four beeps;
if the engine starts, the “exhaust gases” icon will be displayed on the key fob display (this icon may differ on different Starline models) and the car’s dimensions will blink three times, accompanied by a siren signal;
warming up of the vehicle's internal combustion engine will be carried out in accordance with the time interval preset in the settings (5, 10, 15 minutes, etc.);
one minute before the end of the specified time period, the “r01” icon will appear on the key fob display. If the time is up, the alarm turns off the engine and the “exhaust gases” icon on the key fob display changes to the “r00” icon.

Autostart Starline by temperature

In the winter season, many motorists need to warm up their car at night. When setting up autostart based on temperature, it is necessary to take into account some points: the presence of a temperature sensor, the location of the sensor, etc.

The sequence of actions for turning on and off automatic start by temperature:

Having selected the icon with a thermometer and the inscription “START”, press button “2” on the key fob (after a sound signal, the value of the set temperature threshold is displayed on the display);
When you turn off autostart based on temperature, you need to select the thermometer icon on the display and press the “2” button on the key fob.

Once inside the car, you must turn on the ignition within 30 seconds, insert the key into the lock and turn it. To completely exit the autostart mode, you must release the handbrake, while the vehicle's dimensions will blink once, after which a sound signal will sound.

How to reduce the ignition support time or turn it off completely

Hello, I would like the turbo timer to work immediately after the ignition is turned off. And not after ignition support (6 minutes) alarm A93 2can-2lin.

Emergency shutdown of alarm without key fob

To emergency turn off the Starline A93 alarm without a key fob, you must use the Valet service button. They work like this:

open the door with the key - an alarm sounds;
turn on the ignition;
press the service button four times within 20 seconds;
turn off the ignition.

After this, the alarm system is turned off. You can start the car.

How to activate the turbo timer?

Starline alarm models, the procedure for activating the turbo timer function is different.

Device activation

After completing the setup, you must select the desired option to turn on the device. The Apexi turbo timer allows activation in the following ways:

after turning on the handbrake and turning off the ignition;
using a key fob, after arming the car;
when securing the car with the parking brake.

The implementation of how to disable the turbo timer for each model is done differently. Usually it is enough to perform the reverse actions of activation. If the turbo timer is not in demand, you should deactivate the icon on the key fob.

Starline A93 service mode - what is it

The A93 security complex has a lot of functions that not only resist theft, but also make life much easier for the owner. This is an option for a turbo timer, remote engine start depending on temperature or time, as well as additional security modes such as “Panic” or “Anti-robbery”. If the system needs to be checked at a specialized center to troubleshoot problems, the Starline A93 service mode will be required.

This article will tell you in detail what this option is, how to enter or exit it, and also whether there is a way out of the situation when this function fails or does not turn on.

Setting up the Starline A93 key fob after removing the battery

Sometimes the alarm starts to malfunction. If the reason is a deep discharge of the battery, then the battery should be replaced. However, there may be cases when the Starline car alarm will not work correctly even after installing a new part. Then you should reset to factory settings:

turn off the ignition;
press the settings button 9 times;
turn on the ignition, nine siren signals will indicate the success of the procedure;
Let's see a second reset for the second table, now you need to press the settings key ten times;
after finishing, click on the service button and listen to one siren signal;
press K1 of the key fob, the machine will make a sound, indicating a return to standard settings;
turn off the ignition, the car will blink three times with the emergency lights, indicating a successful procedure.

READ Starline b9 alarm does not respond to key fob

Setting the duration of starter cranking

It happens that the car does not start in cold conditions if the starter operates for about a second (Starline A91 factory settings). In this case, you can extend its operating time. The instructions are as follows:

with the ignition off, you must press the Valet service button six times to enter the programming mode;
after turning the key (On), the car's lights will blink six times. Then you need to press the Valet key nine more times;
pressing any button on the key fob determines the starter rotation speed (first – 0.8 seconds, second – 1.4 seconds, third – 2.0 seconds). Long plus short click of the first button – 3.6 seconds.

To prevent the starter from turning when the engine is running, you need to connect the gray and red wire to the tachometer panel for automatic stop.

Setting up the closer

How to set the key fob to turn off

In order to avoid accidental clicks in your pocket and activation of unnecessary functions, there is an option to turn off or block the Starline A91 key fob. To do this, press the first and third buttons simultaneously. Unlocking occurs when the second and third keys are pressed simultaneously.

Reset

If various problems or car alarm glitches occur, it is recommended to reset the settings to factory settings. To remove them, you must perform the following procedure:

the ignition key is inserted into the lock and turned to the On position;
after this, press the Valet service key 10 times;
Now you need to turn the key to the Off position. The machine will blink its dimensions ten times and also emit ten beeps, confirming a successful transition to the user settings reset mode;
press the Valet button again, and the car beeps again;
The first button on the key fob is now pressed. A short melody will confirm that the operation was successful and all parameters are returned to factory settings;
To complete the procedure, you need to turn the key to the On position. The second way is to not press anything for ten seconds. The car itself will indicate that the exit has been completed by blinking its dimensions. The keychain will play a short melody.

How to set up the key fob after replacing the battery

press and hold button three until the third beep. The clock on the display now flashes.
using the first and second keys we increase or decrease this indicator;
The next click on the third key takes you to setting the minutes. It is carried out in a similar way (keys one and two);
Next comes setting the alarm clock, as well as setting the time on the timer;
To confirm the parameters, just do not click anything for several seconds.

Next, you should restore the remaining parameters set by the user.