Jaguar EZ-BETA: Instructions and manual in Russian

Jaguar car alarms compare favorably with other security systems available at a price of 80-100 USD. This brand is the most “friendly” for a novice user. Even a novice installer can connect the Jaguar alarm system, even when it comes to the almost top-end EZ-Beta model. The main thing is that all the options in it will be programmed correctly right away. By connecting the equipment according to the standard scheme, you will not need to program anything. Other features characteristic of Jaguar car alarms model EZ-Beta V2 are discussed in the text.

This security system...

Page 6

Image
Text

This security system (car alarm) is a complex electronic device.

Installation, connection and configuration of the car alarm are described in detail in the “Installation Instructions” and can be carried out by the consumer in full independently.

However, the manufacturer strongly recommends that you entrust the implementation of the specified complex

works certified according to GOST R 51709-2001 (OKUN 017613) service center, which specializes

is planned for the installation of alarms and/or additional electronic equipment in cars

niya, (hereinafter referred to as a certified service center).

The car alarm is intended for permanent installation on a vehicle with power

tion from its on-board 12 V DC voltage, the negative pole of the battery is connected to the vehicle ground.

Before installing a car alarm on a car, first connect all the wires to it in test mode, make sure that all connections are made correctly, connect power from the battery

battery and make sure the car alarm is working properly.

If installing a car alarm requires drilling holes or any other modification to the factory

parts of the car, be sure to first consult about the correctness of such

intervention in the design at the nearest dealer.

Never install the car alarm central unit where it will become very hot, for example from direct sunlight or hot air coming from the car's heating system. Also avoid places where the central unit of the car alarm and its components

The products will be subjected to strong vibration or become exposed to dust or dirt.

Use only the fasteners included with the car alarm installation kit. In this case, the installation will be reliable and safe. The use of parts not included in the car alarm installation kit may lead to disruption of its normal operation.

When washing a car, it is unacceptable for water and detergents to get on the surface or inside the central unit of the car alarm, on its components (siren, sensors, antenna module, limit switches).

switches), as this may damage the car alarm. To ensure moisture protection, it is advisable to initially install car alarm components in places inaccessible to the flow of liquids and splashes, and if necessary, take precautions during washing

or cover (wrap) the components with readily available household waterproof material, such as

polyethylene film, etc.

Never insert any objects into the central unit of the car alarm or its components to avoid damage to the electronic units and systems.

In the event of a suspected breakdown, do not try to open the body of the car alarm (its components) yourself, and please avoid entrusting diagnostics and/or repairs to incompetent persons.

persons. If the car alarm is faulty, contact a certified service center.

Cleaning. Do not attempt to clean the key fob or other car alarm components with

any aggressive liquids, solvents or chemicals, as this may cause

deterioration of its appearance. For cleaning, use a clean, dry cotton cloth (soft

forge a brush).

Due to the constant work to improve car alarm systems, increasing its reliability and

improving performance characteristics, minor changes can be made to the design

changes not reflected in these Instructions.

RULES FOR THE SAFE USE OF CAR ALARMS

JAGUAR EZ-p “System operating and installation instructions”

© Saturn Marketing Lt

Specifications

Jaguar signaling models EZ One, EZ Four, EZ Six, TEZ and others have the following properties:

packet data transmission between the microprocessor unit and the pager is performed at a frequency of 433.92 MHz;
the range of operation of the communicator in pulse transmission mode is 600 meters in open areas with a minimum of interference;
the operating range of the main remote control in command receiving mode is 1200 meters;
the operating range of the spare pager has been reduced to fifteen meters;
to protect the electrical circuits of the anti-theft complex during installation, it is necessary to use safety devices with a rating of 7.5 to 30 amperes, depending on the section of the circuit;
the current consumption when the protective mode is activated is less than 15 mA;
activation of the protective mode can be done at intervals of five, thirty or forty-five seconds;
to protect the car, triggers are used for the doors, trunk, hood, parking brake lever, power input of the ignition system, shock controller, auxiliary controllers and warning zone;
the possible number of transmitters that can be connected to the system is four;
The signaling must be powered from an electrical network with a voltage in the range from 9 to 18 volts.

Clarification for vehicles with manual transmission

You need to understand that the car needs to be prepared before starting the engine using autostart. However, we are talking only about cars with a manual transmission. And here's what the instructions say about this:

When the last door is closed, the security mode can be turned on. This is exactly how the TEZ B system should be used.

This is how a car is prepared for autostart

An alarm from another brand, such as Starline, may work differently: between steps 1 and 2, you press a button. Jaguar systems do not provide such a method. By the way, the sequence discussed above is also used when turning on the turbo timer: if it is not followed, the engine will stall in step 2. The turbo timer option must also be enabled in the settings.

How to install?

In accordance with the instructions for using the Jaguar alarm system with auto start, installation is performed as follows:

The battery turns off. Installation and installation work must be carried out with the on-board network de-energized. If your car has a car radio with a programmed code, do not disconnect the battery until you have read the manual for the audio system or car.
A microprocessor module is mounted in a hidden place. The main unit can be installed behind the dashboard, so the length of the wires will be minimal and the device will be hidden. Disassemble the center console and remove the steering column trim. The connectors with plugs are disconnected from the device and the fastenings are disconnected. Do not fix the unit on a metal surface, as this may cause malfunction. The device is secured using self-tapping screws or double-sided tape.
A siren is installed under the hood, and a limit switch is mounted on the hood itself. When installing these elements, please note that they must be placed in places where moisture does not accumulate. The siren cannot be installed near the cylinder block, as it will quickly break under the influence of elevated temperatures.
Install a transceiver with a button to call the car owner inside the car. This element should be mounted on the windshield, but there should be no metal surfaces or wires near the device. Their presence will result in interference during signal transmission. The transceiver is fixed using a sticker or double-sided tape.
The impact controller is mounted on a partition separating the interior and engine compartment. The device is fixed to a metal surface using self-tapping screws or tape. The shock sensor must be located so that if adjustment is necessary, the driver has free access to the device.
Install a service button in one of the bundles with standard wiring. It should be placed under the dashboard. You can additionally wrap it with electrical tape.
The wires are laid under the car's trim; to do this, you will have to disassemble part of the upholstery. It is recommended to lay electrical circuits away from power wires (ignition system, high-voltage cables, etc.), as well as electronic devices. This may lead to signal malfunctions due to interference.

The Avtozvuk channel talked about the mistakes that consumers often make when installing car alarms.

User manual

You can use all the functions of the Jaguar alarm system with auto start only after binding the remote control.

Binding procedure:

Disable security mode, get into the car. Insert the key into the ignition, but do not turn it. The binding is performed with the ignition turned off. Click on the service key seven times.
Within five seconds after the last press, turn the key to the On position, this will turn on the ignition.
The siren of the complex will play seven sound signals, this indicates its readiness for binding.
Within ten seconds after the last signal, hold down the first and second keys of the pager, they show an open and locked lock. The system will emit one signal to confirm the binding.
To program a second pager, follow the same steps. Two beeps will sound as confirmation.

Designation of buttons and indicators on the key fob

The description of the key fob buttons is shown in the photo below.

Identification of Jaguar key fob buttons

Designation of command and mode indicators:

A – anti-robbery option;
B – auxiliary communication channel, available for programming;
C – option to start the internal combustion engine based on air temperature;
D – daily start function;
E – indicator for enabling or disabling the remote start of the internal combustion engine;
F – indicates activation of silent security;
G – protective mode with sound confirmation;
N – remote deactivation of the sensitivity controller;
I – service mode indicator;
J – machine status and temperature indicator;
K – auxiliary second channel;
L – indicator for remote opening of the trunk door.

Schematic representation of the display
Status indicators:

Built-in battery of the communicator. By the icon you can determine whether the battery needs to be replaced.
Auxiliary second channel.
Option to start the internal combustion engine based on temperature.
The power unit of the car is started.
The tailgate is open.
Option to notify the car owner via vibration.
The car doors are open.
Service mode.
Indicator for automatic reactivation of the protective function.
Silent security icon.
Protective mode indicator with sound confirmation.
The car hood is open.
The sensitivity controller indicator turns on when there is a blow to the car body.
Hand brake.
Closing door locks.
Opening door locks.
Remote control receiver operation indicator.
Machine communication confirmation icon.
Car owner call icon.
Energy saving mode activation indicator.
Icon of activated ignition in a car.
Alarm indicator.
AM – first half of the day.
PM – afternoon time of day.
Indicator for daily start of internal combustion engine.
A symbol indicating the temperature in the cabin and the current time.
Temperature scale.
Timer.

Setting up autorun

Start the motor by command:

Click on the button in the shape of a locked pad and hold it.
When the remote control emits a melodic signal, release the key and click on the third button labeled Ch/Prog.
The car's lights will blink three times, this indicates a successful start of the internal combustion engine.
An indicator in the form of smoke from the exhaust pipe will appear on the remote control display.

Alexey Zamur showed in the video how to remotely start the engine on a Renault car.

By time

To start the internal combustion engine on time, follow these steps:

Make sure the time on the remote control is set correctly.
Set the alarm for the time at which the start will take place. After setup, a bell icon will appear on the remote control screen.
Click on key 3 and hold it down until the remote control emits two beeps - one melodic and one short.
Release the third button.
By briefly clicking on the third key, move the remote control cursor to the screen indicator with the inscription Clock Start.
Click on the button in the form of a key and a locked pad, this will activate the function. The lights on the car should blink once, and the remote control will emit a melodic signal.
After it is played, an indicator with the inscription Clock Start will appear on the transmitter display next to the bell icon.

By temperature

Procedure for starting an internal combustion engine based on temperature:

Click on the third key on the remote control and hold it down until the device plays one melodic and one short-term signal.
Release the key. On the remote control screen in the bottom row one of the icons will begin to blink.
With short clicks on the third key, move the cursor on the communicator screen to the icon in the form of a thermometer with the inscription Temp Start.
To confirm that the function is enabled, click on the button with the locked lock and key. The vehicle's lights will blink once. The pager display will display an icon with a thermometer and indicate the temperature at which the engine will start.

Synchronizing the EZ-Two Switch

Linking the Jaguar EZ Tu feedback transmitter is carried out according to the instructions.

Disable car security. Activate the ignition.
Press the "Jack" button for five seconds. The siren will sound four times and the LED will blink the same number.
Click the “Trunk Opening” and “Speaker Crossed Out” buttons. The key fob will beep twice.
Following the steps above, register the remaining transmitters.
Turn off the ignition. The direction indicators will blink five times to confirm exiting the setup mode.

Bottom line

The Jaguar security system is a godsend for every car owner on a limited budget. When configured correctly, it will provide reliable protection for your car.

Tired of paying fines? There is an exit! Forget about fines from cameras! An absolutely legal new product - Traffic Police Camera Jammer, hides your license plates from the cameras that are installed in all cities. More details at the link.

Absolutely legal (Article 12.2);
Hides from photo and video recording;
Suitable for all cars;
Works through the cigarette lighter connector;
Does not cause interference to radios and cell phones.

Find out more Subscribe so you don't miss anything important 02/23/202053 Alarms

The Jaguar security system with automatic engine start has proven itself on the positive side due to its reliability. It not only provides car security, but also allows you to control the basic functions of the car. Instructions for using the Jaguar alarm system with auto start allow the car owner to correctly install and connect, as well as configure the complex.

Not attached: what to do

It is not always possible to register the remote control in the memory of the Jaguar anti-theft system (XJ 770, 777, JX 1000, 2000, 4000, 330, 110, 220, JM 395, 370, 390, JA 270). Why does this happen:

The Valet key was accidentally pressed. Turn it off. Register the switch again. Check its functionality;
“ignition on” is not recognized by the main alarm unit. Contact the service center;
the transmitter is broken. Replace with a new one;
breakdown of the anti-theft system control unit. Take the car to a service station.

Setting up Jaguar autostart

Jaguar autostart is very convenient. It allows you to configure automatic engine starting using a timer, as well as warm-up time, engine operation and starter cranking. First, make sure that the date and time on the key fob are set correctly. Next, you can start turning on autostart and set the starter cranking time.

Auto start on alarm clock. Sequentially click on the buttons with the image of a lock with a key and “Check progress”. Next, place the cursor on the “Clock start” icon and set the autostart time you need. To disable autostart, place the cursor on the “Clock start” icon again and press the key fob button. An indication will follow.
Autostart by timer. Follow the same steps as for autostart on an alarm clock, but place the cursor on the “Fixed start” icon. To turn off autorun by timer, move the cursor to “Fixed start” again and press the key fob button.
Autostart based on temperature. The engine warm-up time is determined by a pre-programmed function. In order to set the engine to autostart based on temperature, place the cursor on “Temp Start” and turn on autostart. After switching on, an indication and temperature value will follow (for example, -10°C). To turn it off, move the cursor again and press the key fob button.

If the alarm is not set to autostart, double-check the correctness of the actions you took. Make sure that the alarm is installed correctly and maintains “program neutral”: the engine is turned off, the hood is well closed, etc.

Jaguar Mini sewing machine: features, model overview and operation

If the autostart still does not work, contact a warranty specialist.

Advantages and disadvantages

According to owner reviews, the alarm has positive aspects:

optimal set of functions;
convenient control of launching options via key fob;
availability of remote start;
good range of remote controls;
there is a feedback channel;
affordable price compared to competitors.

Users note a number of disadvantages of the Jaguar TEZ B system:

the system has been discontinued, so there are difficulties with ordering spare components;
during operation, peeling and destruction of the conductive paths on the printed circuit board occurs;
Over time, the buttons on the main key fob fail;
One limit switch was supplied in the kit;
a simple command encoding algorithm that is susceptible to interception and hacking;
There may be problems with control due to desynchronization of key fobs.

Emergency disarming of the Jaguar TEZ Beta is demonstrated in a video filmed for the sigmax69 channel.

Idle training

The car alarm itself controls the operation of the motor in one of three ways: by the tachometer signal, by the TACH generator terminal, or by the level of ripple in the network. The most reliable is the first method. In this case, the gray-black cord from the 18-pin connector is connected to the tachometer terminal, and function 8 from the settings table is assigned a value of 3 or 4. Another important action will be the following - the system needs to be taught “idle speed”.

Tachometer signal at startup

You need to do the training like this:

Let’s say that at the last step the siren does not go off, but instead the “dimensions” turn on five times. This means that mistakes were made. This procedure is suitable for one signaling device – Jaguar EZ Beta. One thing can be said about the A9 system: this procedure is not given in the instructions for it. In turn, for Jaguar EZ ONE alarms, “training” does not make sense - everything is configured automatically.

If autostart is not used, engine operation control is not required. In this case, there is no need to “train” the car alarm.

Appearing faults

When operating the Jaguar alarm system, the following malfunctions may occur:

Incorrect response (false). This usually happens due to the high sensitivity threshold of the shock sensor. When setting it up, you slam your palm on the car body and set the value at what impact force you need to turn on the siren.
Incorrect installation of alarm components.
The key fob batteries are low.
The key fob itself has failed.
The antenna is faulty.
The wiring is broken.
The car battery is discharged.
System settings software failure.

If a malfunction of the security system is detected, it is recommended to fix it as quickly as possible.

The alarm system is not 100% protected against theft or burglary. There are special code grabbers that steal the alarm code for subsequent hacking of the car.

Key Features

Main functions of Jaguar alarms:

Possibility of activating the protection mode with or without sound and light accompaniment.
The ability to notify the car owner about events recorded by the security system. The key fob with feedback displays data about activated security zones.
Protection against robbery, this function is called Anti-hijack. She is intelligent. The essence of its action is to block the motor when the car is forcibly seized. When criminals force the car owner out of the car, the alarm system can understand this by analyzing the operation of the sensors installed on the brake pedal and handbrake lever. After the car moves to a safe distance from the car owner, the engine lock will be activated.
The consumer can independently select the signal that is played when the alarm is activated.
Seven independent security zones provide more reliable protection.
Disabling the protection mode is carried out in two stages.
The ability to warn the car owner that he forgot to lock the doors before driving.
If necessary, you can connect the steering horn to the car siren.
Automatic start. This option will ensure the engine warms up in the cold season and will be useful for those who are constantly late. Now you don't have to waste time warming up the car.
The memory of the microprocessor module allows you to record information about events that occurred in the operation of the security complex. Even after disconnecting the battery, information about this will remain in the memory.
The consumer has the opportunity to additionally connect digital relays used to block the power unit.
The consumer has the option of additionally connecting a GPS beacon to the signaling system.

Installation

Characteristics of activity:

Professional installation of additional equipment in your car. Here are some of the works we do:

Car audio installation: installation of car radio, acoustics, subwoofer, amplifier, TV, monitor, antenna.
Installation of rear view cameras.
Installation of security systems. Installation of car alarms of any complexity on any cars: car alarms with feedback, with auto start. Installation of a car security system, search system, GSM-GPS module. Installation of a mechanical anti-theft device.
Installation of parking sensors.
Installation of window regulators.
Installing a DVR.
Installation of xenon, bi-xenon.
Installation of fog lights.
Car soundproofing.
Car window tinting. price list 12 Volt

Equipment

The alarm is supplied in a cardboard box, the set consists of the following components:

main system module;
main key fob equipped with three buttons, two-channel communication and a monochrome LCD screen;
an auxiliary key fob equipped with four buttons, a single-channel operating mode and a control indicator for command transmission;
a transceiver unit, which includes an antenna, a driver call button and a sensor for measuring the temperature in the cabin;
shock measurement sensor complete with wiring harness;
non-autonomous siren;
control light diode equipped with a wire and plug for connection;
setting button, complete with cable;
additional anti-robbery button, equipped with a connecting harness;
switch installed under the hood or trunk lid panel;
a set of Molex type wires intended for switching the main module;
additional Molex harness, equipped with wires of increased cross-section for the car remote engine start system;
Molex harness for connecting the alarm system to the central locking control unit;
warning stickers (two pieces);
Jaguar TEZ B instructions for use, configuration and installation;
brief reminder;
Warranty service form.

General view of the Jaguar TEZ Beta set