Changing the cabin filter on Lada Kalina-2 yourself

The cabin filter of the Lada Kalina is a small piece made of corrugated paper, the condition of which determines the cleanliness of the air in the cabin. More precisely, air in any case, it must arrive clean, but the amount of incoming air depends on the level of filter contamination. Let’s say that in winter the heat of the stove becomes worse. Then, first of all, look at the filter, and only then at the condition of the heater. It is easy to understand that the cabin filter can always be replaced. And any owner can perform this operation.

When should you change the cabin filter?

The instructions included with the car state that the cabin filter should be replaced every 15 thousand kilometers. If the operating conditions of the car are harsh (frequent trips on dirt roads), then the period is halved - after 8 thousand km. Specialists at stations recommend replacement twice a year, before the start of the autumn and spring seasons.

A clogged cabin filter must be replaced with a new one.

Useful tips

Please note that when replacing the filter, it is necessary to simultaneously clean the drainage hole of the drainage box. You need to clean both from the side of the box and from the side of the front right wheel niche.

Let us remind you once again that when installing the filter, the pointer arrow (on the original filter and a number of analogues) should be directed downwards, and the “front” inscription should be directed towards the front of the car.

After installing a new cabin filter, do not rush to tighten the cap and begin reassembly. First you need to check that the latches securely fix the element, since a filter that is not fastened well enough can fly off when driving.

The process of replacing the cabin filter on Kalina

Before replacing the filter, we should collect everything we need for work.

• a screwdriver with an asterisk profile (T20 is ideal);
• Phillips screwdriver;
• slotted screwdriver (flat blade);
• rags;
• new filter.

Tools and Supplies - Gallery

Sequence of operations

1. Open the hood and find the place where the filter is located on the right side of the decorative trim between the hood and the windshield.

Decorative grille protecting the cabin filter of the Lada Kalina

Tip: for convenience, you can turn on the wipers and lock them in the up position by turning off the ignition.

The grille is attached with self-tapping screws, some of which are covered with plugs. Exactly how long it will be closed depends on the year of manufacture of the car. Remove the plugs by picking them up with a sharp object (a slotted screwdriver will also do the job).

Removing the plugs on the screws of the cabin filter grille of the Lada Kalina

Step-by-step instruction

It is known that the cabin filter of the Lada Kalina-2 is replaced every 15,000 km. The indicated numbers are the maximum value, that is, in practice, replacement can be made more often.

How to get to the cabin filter

To gain access to the part we need, follow these steps:

1. Approach the car and, without opening the hood, unscrew the 3 screws securing the right frill (see figure);
2. Open the hood, remove the negative terminal from the battery (you need a 10mm ). Unscrew 2 more screws that hold the plastic frill and remove this part. A “t20” screwdriver fits under the head of the screws;
3. Using a regular Phillips screwdriver, all you have to do is unscrew the two bolts holding the filter compartment cover;
4. We remove the compartment cover, remove the filter along with the frame, and replace it.

If you decide to install a mesh, place it above the filter, not below it. In the standard version, however, only replacement is provided.

Plastic frame and filter element

Each owner can change the fuse or install a cabin filter without resorting to the services of a car service. But replacing a light bulb in a headlight is a more difficult task. But since we are talking about self-repair, we emphasize once again: as soon as the hood is open, disconnect the “negative” contact of the battery. At the final step, of course, it is necessary to return everything to the way it was.

The ability not to change the device

Whether to change the filter or not is up to the owners to decide for themselves. If it is relatively clean, you can proceed as follows:

1. The filter is removed according to the scheme described above.
2. Clean the seat thoroughly using a vacuum cleaner.
3. Then vacuum the filter and rinse it with running water (for severe contamination, soaking and detergents will be required).
4. After which it is treated with a steam generator and blown with compressed air;
5. After 24 hours, the filter can be put back in place.

Such a replacement will last for several months, but the owner will have to replace the part as soon as possible.

Goals and tasks that we solved

We looked at how to replace a part called the cabin filter. In principle, you can not change anything, but simply clean it and return everything to its place. How best to accomplish this, the owner will decide for himself. Also, the instructions will be useful if the owner decides that it is necessary to change the stove radiator. First, the filter is removed, then the dashboard is removed, and then access to the radiator appears.

The filter element, if not changed for a long time, can crumble from any touch. In such cases, there is no need to take unnecessary risks. For those who are not confident in their abilities, it is easier to entrust all actions to professional repairmen.

About differences in device location

Regardless of the class of the Lada Kalina, the cabin filter is located in the same place. Moreover, starting with Kalina-2, many parts (including filters) were transferred to all subsequent VAZ models, so the principle of replacing this device does not depend on the body type, engine size or the presence of a car radio.

The quality of the air that passengers breathe depends on the cleanliness of the cabin filter on Kalina. It is recommended to change it twice a year; the operation is not very complicated and takes no more than half an hour.

The cabin filter of the Lada Kalina ensures the purification of air flows that enter the interior of the car. In addition, the element traps particles of dust, pollutants, and prevents the penetration of unpleasant odors.

Over time, the product wears out and loses its protective properties, as a result of which the healthy microclimate in the car interior is disrupted, the windows fog up, dust and unpleasant odors penetrate. Filter products, and especially the cabin filter for viburnum with air conditioning, must be replaced at least 2 times a year.

The operating principle of the unit.

The CCGT is mounted on the cabin panel. The clutch accelerator is connected to the unit via a pusher. When the clutch is disengaged, the rod is pressed against the piston of the pneumatic cylinder. When you press the accelerator, fluid flows through the channel into the amplifier. The movement of the pusher opens the valve of the pneumatic system. When the required pressure is reached, the inlet valve opens completely and air enters the pneumatic cylinder chamber. The piston, together with the clutch release pusher, reaches the top point. A feature of the piston’s operation is the effect of two forces on it. On the one hand, it is exerted by the pressure of the compressed air of the pneumatic system, on the other, by the action of the working fluid of the hydraulic booster. The systems are designed in such a way as to provide maximum comfort for the driver to control the clutch mechanism. When the pedal is released, the pressure of the power steering fluid decreases and the pneumatic cylinder stops its operation. The exhaust valve opens and the air escapes to the atmosphere. If the unit breaks down, the clutch is disengaged only through the operation of the hydraulic booster.

Pneumatic system design.

The mechanism consists of a tank mounted on a frame, a single safety valve and lines. The air supply to the amplifier is carried out through a separate circuit of the system. The valve is located on the reservoir and separates the air lines leading to the clutch mechanism and other components. There is a tap to drain the condensate formed in the cylinders.

PGU device.

The amplifier consists of a housing, inside of which there is a piston and a pusher. The piston has a cuff and moves in the axial direction. The amplifier housing is closed on top with a lid through which the pusher passes. To protect against dirt and dust, a wiper is installed in the mechanism on the amplifier cover. The pusher is connected to the clutch release accelerator by a fork mechanism. The accelerator is installed on the axis of the bracket. Air is supplied to the unit from cylinders through the operation of a valve mechanism.

Main malfunctions of the mechanism.

Ural 5557 PGU and hydraulic booster fail for the following reasons:

1. Swelling of the sealing ring.
2. Incorrect adjustment of the mechanism.
3. Wear of cuffs and other elements.
4. Release cylinder fork bend
5. Fork axle wear.
6. Pedal failure.
7. Drive jammed.
8. Valve wear.

If the mechanism jams, it is worth disassembling it and rinsing it in gasoline or kerosene. Wear of sealing rings and valves leads to leakage of compressed air from the cylinders. This problem can be noticed by the constant “hissing” of the unit. If the problems of the clutch PSU are not corrected in a timely manner, breakdowns of the hydraulic booster may occur in the future, which will lead to a stop in the operation of the vehicle and the need to install new spare parts from the Ural plant.

In what cases is it necessary to replace the unit?

Intensive use of the vehicle in urban conditions, where acceleration and braking often occurs, entails rapid wear of the transmission mechanisms. Frequently pressing the clutch accelerator entails wear on the amplifier itself. Ultimately, when the mechanism wears out, the smoothness of starting and shifting gears significantly deteriorates. In addition, sharp vibrations are transmitted from the engine through the transmission to the car frame. The PSU solves many problems, so its malfunction entails loss of comfort in controlling the mechanism and the vehicle as a whole.

Adjusting the clutch pedal.

One of the problems with the operation of the amplifier is incorrect installation of the accelerator. To fix the problem, adjustments must be made. It is carried out in several stages:

1. Bleed the air from the cylinders.
2. Move the pneumatic cylinder to the upper position and fix it.
3. Press the clutch accelerator to the floor.
4. Adjust free play.
5. Measure the stroke of the pusher with the engine running.

If the accelerator stroke is adjusted incorrectly, the amplifier will not be able to ensure smooth gear changes and starting the car.

Types of filter elements

It should be noted that there are two most common types of products: - coal type; - paper type.

The carbon element has excellent filtering characteristics. The product perfectly freshens the air, copes with dust and unpleasant odors (dampness, exhaust gases and emissions). The optimal place for use is large, polluted cities. The disadvantages include the rather high price and short service life.

A paper filter element is much cheaper than a carbon one, and is slightly more durable under conditions of proper use. In principle, it also carries out all the necessary protective functions, but does not do it so zealously and thoroughly. The disadvantages include excessive fragility and wear when the product gets wet.

How often should I replace?

In accordance with the requirements of the operating instructions, the cabin filter on Lada Kalina is replaced every 8,000 km. mileage The indicator is average. In conditions of increased dust and gas contamination, reduce the replacement interval by a third.

The first signal that it is time for an update is fogging of the windows and weak air flow from the deflectors. Less often - the appearance of a fetid odor, sweetness, rot in the car interior.

Considering the simplicity of the procedure, you can change the cabin filter on a Lada Kalina yourself. Contact the service center for help, as a last resort, when the installation technology is broken or there are other damages associated with unprofessional intervention. At the stage of the factory warranty, it is advisable to refrain from do-it-yourself repairs.

Choosing a cabin filter for Lada Kalina

The most common foreign manufacturers of consumables for Lada Kalina:

• CORTECO, article number 80000999, price from 1000 rubles. Filter with the addition of activated carbon. Dimensions: 25.0 x 15.0 x 3.25 cm;
• DELPHI TSP0325329, from 1000 rubles;
• ALCO FILTER MS-6405, from 700 rubles;
• BOSCH 1987432230, from 700 rubles;
• CORTECO 80000998, from 700 rubles;
• FILTRON K1229, from 700 rubles;
• MANN-FILTER CU26004, from 700 rubles;
• SCT SA 1150, from 500 rubles;
• WIX FILTERS WP2000, from 500 rubles.

1.6 liters / 16 valves / 90 hp / from 2004

• AG Auto Parts, AG5011, from 300 rubles;
• ALCO FILTER, MS-6405, from 300 rubles;
• BOSCH, 1987432230, from 300 rubles;
• CHAMPION, CCF0419, from 300 rubles;
• COOPERSFIAAM FILTERS PC8358, from 300 rubles;
• FILTRON K1229A, from 300 rubles;
• FILTRON K1229, from 300 rubles;
• FRAM CF11640, from 300 rubles;
• KNECHT LA933, from 300 rubles;
• MAHLE ORIGINAL LA933, from 300 rubles;
• MANN-FILTER CU26004, from 300 rubles;
• SCT Germany SA1150, from 300 rubles;
• WIX FILTERS WP2000, from 300 rubles.

1.6 liters / 82 hp / until 2010

• FILTRON, K1230, from 500 rubles;
• KNECHT LA944, from 500 rubles;
• MAHLE ORIGINAL LA955 from 500 rubles;
• WIX FILTERS WP2012, from 500 rubles;
• WIX FILTERS WP2040, from 500 rubles.

1.4 liters / 8 valves / 88 hp / from 2004

• AG Auto Parts, AG5055, from 300 rubles;
• ALCO FILTER MS6306, from 300 rubles;
• BOSCH 1987435244, from 300 rubles;
• CHAMPION CCF0650, from 300 rubles;
• CHAMPION CCF0720C, from 300 rubles;
• FILTRON K1300A, from 300 rubles;
• KNECHT LA955, from 300 rubles;
• MAHLE ORIGINAL LA984, from 300 rubles;
• MANN-FILTER CU26789, from 300 rubles;
• SCT Germany SA1276, from 300 rubles;
• WIX FILTERS WP2014, from 300 rubles.

1.4 liters / 16 valves / 88 hp / from 2008

• AG Auto Parts, AG6012, from 300 rubles;
• ALCO FILTER MS6422, from 300 rubles;
• BOSCH 1987434498, from 300 rubles;
• CHAMPION, CCF0425, from 300 rubles;
• FILTRON, K1321A, from 300 rubles;
• FILTRON K1396, from 300 rubles;
• KNECHT LA785, from 300 rubles;
• MAHLE ORIGINAL LA652, from 400 rubles;
• MANN-FILTER CU26545, from 400 rubles;
• SCT Germany SA1020, from 400 rubles.

When purchasing on your own, always give preference to specialized stores, dealership centers, and authorized workshops. Where they provide a quality guarantee for the products sold.

Replacing the cabin filter Lada Kalina

Preparatory stage: a set of automotive tools, screwdrivers, a new filter, rags. Where is the cabin filter located: in the engine compartment, on the left side, under the frill.

• We set the car on the hand (parking) brake, open the hood;
• in the upper left part, under the frill, unscrew the plastic decorative cover. It is secured with two bolts. We extract it;
• carefully pry up the air element, carry out preventative maintenance on the housing, remove dust, debris and leaves, which impedes natural air circulation;
• we lay a new purifier and assemble the structure.

We check the proper functioning, tightness of fit, and tightness. Provided that the installation is correct, the filter must be changed no earlier than after 8,000 km. At the same time, we inspect the parts and mechanisms in the engine compartment. It may require prompt replacement or installation of new consumables. If difficulties arise, always consult with specialists.

A little more about digital notation

If you intend to buy a new cabin filter for Kalina-2, know that this part may be designated as follows:

• 11180-8122010-00, or 08 (there is a plastic frame);
• 11180-8122010-01, or 03;
• 11180-8122010-82 (produced by Lada Image CJSC), or 83 (coal, Lada Image CJSC).

The part itself may have an arrow designation. In this case, you need to remember: the arrow shows the direction of the air flow. She should look "down".

Kit 11180-8122010-08

The main thing that I would like to note here is that the filter inside the compartment must be installed tightly. That is, there should be no gaps at the edges. The frame, made of plastic, does its job well.