Ka Rio tire and wheel parameters, Kia Rio bolt pattern

The third generation Kia Rio (factory designation UB, although QB is also available) was produced from 2011 to 2015. Moreover, the plant in St. Petersburg produced a version of the Kia K2, originally developed for the Chinese market, but adapted for Russian conditions.

In the factory configuration, the Kia Rio III was equipped with only two tire sizes with two different diameters. On the one hand, this seems like a lack of options. On the other hand, it is easy to install wheels with a large diameter on this car. Moreover, they will look impressive and you will not have problems operating the car. But more details about everything in the article.

Dimensions of wheel bases and tires for Kia Rio

The Kia Rio wheel size recommended by the manufacturer is used to avoid difficulties with their installation and driving in the future.
On a Kia Rio, the size of the factory wheels and tires is determined by two factors:

• modification of the installed engine;
• production year.

On the Kia Rio, the following were installed in the middle of the wheels:

• width of the sliding part of the tire - 175 mm;
• depth of rubber chassis - 70 mm;
• PCD drilling - 4 × 100 mm;
• departure - ET40;
• wheel diameter - 13 inches;
• The width of the central hole is 54.1 mm.

installed on the hub with a bolt with parameters M12 × 1.5.

A number of Kia Rio 2 JB 2005-2011 car models have the following wheel sizes:

• element chassis width - 175 mm;
• treadmill tire depth - 70 mm;
• bolt pattern on Kia Rio 2 - 4 × 100 mm;
• ET - 39-46 mm;
• tire width - 14 inches;
• central center circumference - 54.1 mm.

It is attached with fasteners marked M12x1.5 to the hub.

The Kia Rio 3 bolt pattern from 2011 to 2015 is marked with two symbols: UB and has the following dimensions:

• width - 185, 195, 205 mm;
• tread depth - 65, 55, 45 mm;
• bolt pattern on Kiya Rio 3 - 4 × 100 mm;
• ET - 36-52 mm;
• wheel width - 15, 16, 17 inches.
• central mounting hole - 54.1 mm.

it is connected to the hub axle with M12×1.5 nuts.

Kia Rio 4 FB 2017-2019 has tire parameters: 185/65 R15, 195/55 R16, circumference and number of fasteners - 4 × 100, offset ET - 48, central hole with a radius of 27.5 mm. Connects to the hub with bolts, thread M12 × 1.5.

What tire sizes does the manufacturer recommend to install?

The size of wheels installed at the factory depends on two main factors: the production code and the modification of the installed motor. The best solution is to use tires that match the standard sizes set by the manufacturer. During the design, angular acceleration, distribution of weights between the wheels, and other moments were taken into account. You need to carefully read all the nuances.

For all cars produced between 2000 and 2005, without exception, the manufacturer ordered standard wheels:

The wheel diameter is 13 inches. It should be noted that the type of disks that all cars were equipped with is also standard - 5.5J×13. Departure – ET40. This size is quite common. This significantly expands the choice of wheels for upgrading your own car. from 2005 to 2011, the Kia Rio 2 JB version was produced.

The cardinal difference between JB wheels and the earlier model is their larger diameter. It is 14 inches. Moreover, the overall tire dimensions remain the same – 175/70 mm. The next stage of development of this car fell in the period 2011-2017. The modification is marked with a pair of letters – UB. Drilling – 4×100 (as on other versions of the car).

An important difference between UB and earlier modifications is a larger selection of units. As many as 6 trim levels were presented. The engines differed not only in their volume, but also in their type (gasoline/diesel). Directly at the plant, as many as 3 different standard sizes were installed:

Not only the diameter, but also the size of the disks differs. In the first case, with a wheel width of 185 mm, size 5.5J×15 was used. Departure - ET36. Tires 195/55 mm were equipped with disks with a diameter of 6J×16. The latest modifications were equipped with wheels with a diameter of 17 inches. However, the drilling remained standard - 4x100. This greatly simplifies the procedure for selecting new disks.

The latest version of the Kia Rio is the fourth. Marked with the letter FB. This model was produced from 2022 to 2019. Tires of the following sizes were installed:

Replacement with analogues

Manufacturers recommend installing standard disk bases and tires, but options with slight differences in width or height are allowed.

Kia Rio wheel sizes are relevant for cars produced 15-20 years ago:

1. R13/155/80.
2. R14/165/65.

For 2nd generation modifications released in 2005-2011, wheels with the following parameters are suitable:

1. R14/185/65.
2. R15/195/55.
3. R16/205/45.

The third generation is suitable for Kia Rio R15 wheels with parameters: R15 / 185/65.

Other types of wheels were also installed on Kia 3 generations:

• R16/195/55.
• R17/205/45.

The new products of this training, released in 2017-2019, have no analogues.

What non-standard sizes can be supplied?

The manufacturer recommends using only standard size tires. However, it is allowed to install rubber of non-standard diameter, width, with a higher or lower profile height. Moreover, such recommendations differ somewhat depending on the year of manufacture of the vehicle.

Versions of cars produced 2000-2005, marked as DC, can be equipped with the following types of wheels:

For cars that came off the assembly line between 2005 and 2011, there is a larger selection of acceptable sizes:

The third series boasts an even larger assortment of non-standard tires, the installation of which is allowed:

For cars of recent years (2017-2019), the installation of analogues is not expected.

The right choice of disk bases for Kia Rio

When installing original spare parts, car manufacturers guarantee product quality. There are no such conditions for disk databases provided by unknown companies.

For R15 printed elements from an unknown manufacturer, the price will vary from 1000 to 1500 rubles with no quality guarantees. There are non-original cast elements that can be bought from 3,000 rubles.

Also on sale are certified analogues of high-quality light alloy disc bases. In terms of quality and characteristics, they are practically no different from the originals, with the exception of the serial number, and the price will be cheaper, which attracts Kia Rio owners.

Stamped elements made of light metals are considered the highest quality and most expensive, but such wheels are rarely installed on cheap cars.

Most car owners recommend choosing steel elements designed for winter tires. In winter, roads are sprinkled with salt, and original alloy wheels quickly become unusable.

Tires for summer

And now we are looking for an answer to the question: “Which summer tires for the Kia Rio are better?” Tires for the summer season for any car are selected depending on its dimensions and classification. And of course, it matters what roads he has to drive on.

Considering that the Rio is a city car, in which hardly anyone will go hunting, a tire with a road tread, as a symmetrical non-directional pattern is usually called, is suitable for it. Here are some worthy examples:

The question of which tires are best for the Kia Rio cannot be answered unequivocally. Much depends on the capabilities of the car of a particular modification.

For example, for the third and fourth generations, which can ride on low-profile tires size 205/45 R17, as well as for the Rio X-Line crossover, not only the options presented above are suitable.

Tires with a directional tread pattern, similar to the one in the example below, would also be good.

Michelin CrossClimate+

Not only does it drain water better, reducing the risk of hydroplaning, but it also allows you to reach higher speeds. Only in this case, it is necessary to observe the direction of rotation of the wheels, which is indicated by an arrow on the sidewall of the tire.

Asymmetrical tread patterns are less common; when installing such tires, you also need to observe left and right. But this is no longer an option for class B cars.

What is the wheel bolt pattern on KIA Rio cars?

The third generation Kia Rio has a wheel bolt pattern of PCD 4×100. European indicator; indicates the position of 4 bolts on a circle with a radius of 100 mm. The parameter is determined by the manufacturer. These numbers should be used to select replacement options. That is, a 4-bolt design cannot be replaced by a 5-bolt design.

If the ratio of bolts and circumference of the original and the analogue is the same, the size of the Kia Rio 3 wheels is suitable, the analogue can be installed.

The machine has a hole for an M12x1.5 nut. The fasteners are the same for all modifications of the third generation.

To determine the bolt pattern yourself, you will need:

1. We unscrew the steering wheel.
2. Measure the distance between the centers of opposite bolts with a ruler.
3. If there are 4 on the disk, the PCD corresponds to the actual value.

For models with five bolts, the resulting figure must be multiplied by 1.05.

Replacement options and choice

If the parameters of the Kia Rio 3 wheels match, the choice depends only on the preferences and financial capabilities of the owner. The most expensive models are made from light alloys. Forged and cast ones are more reliable than stamped sheet metal ones.

Wheel options - from R14 to R17 (on 5.5 and 6.0.). ET ranging from 40 to 52.

Recommended replacements:

The bolt pattern and center hole diameter should be the same as the original wheels (4-bolt, 54.1).

When choosing, take into account the quality of the road surface where the car is most often used. A large number of holes and potholes are detrimental to the stamped versions: if hit suddenly at speed, the discs bend. But the tire will remain unharmed. The cast or forged version is better protected from deformation, but rubber can be cut in similar conditions.

Before choosing, you should evaluate the cost of repairing disks in local workshops. Restoring stamping is cheaper. But more technologically advanced discs load the suspension less, increasing the long-term service life.

Source

Standard wheel sizes for Kia Rio 1.6i UB

The Kia Rio 1.6i UB model was produced from 2012 to 2022. Table of sizes of normal wheels and those suitable for Kia Rio 1.6i UB.

Disc drilling parameters are usually called bolt pattern:

• LZ (number of holes)
• PCD (Bore Center Circle Diameter)
• ET (start of disc)
• DIA (hole diameter)

Modification of the proprietary model Automatic year Release parameters Width Disc diameter Disc LZ * PCD Origin Diameter ET Type DIA installations

Rio 3 wheel size

In the factory configuration, the third generation Kia Rio was equipped with wheels of only two sizes - with a diameter of 15 and 16 inches. Tires for buyers were also available in only 2 sizes - 185/65 R15 and 195/55 R16. You could choose them no matter what engine you have - 1.4 or 1.6 liters. Also, tire size does not depend on the year of manufacture. Most often, the Kia Rio 3 was equipped with Hankook and Nexen tires from the factory. But based on the tire markings, you can choose other sizes.

Installation of disc bases of non-standard sizes on Kia Rio

The vehicle owner's manual contains recommended settings for major parts. The owner can independently choose the size of the wheel base and tire.

Some drivers are satisfied with the dimensions recommended by the vehicle manufacturer.

The dimensions of atypical elements create a spectacular look. Subsequently, the characteristics of the car may change significantly:

1. Road handling may deteriorate.
2. The grip on the road surface has deteriorated significantly.
3. Steering response changes.
4. The tire's grip on the road surface is lost due to the layer of water on its surface.
5. Reduces stability when moving.
6. The noise level increases or decreases.
7. Affects fuel consumption.
8. Tread wear increases.

Manufacturers do not recommend installing oversized elements.

Tire size for Kia Sorento

The Kia Sorento is another mid-size crossover from Kia.

The rubber on it changes as the seasons change, as the tires wear out, or as you switch to another tire model. Depending on the region where the vehicle is used, weather and natural conditions, it is worth choosing the type of tires to be used - all-season, summer, winter.

Winter tires are also selected depending on natural and weather conditions, and the roads on which you will drive. Winter studded tires are perfect for highways, ice and snow slush on the roads; for city conditions, friction Velcro tires will be more convenient.

You may be interested in this About wheel sizes for Kia Sportage 3

Drilling Kia Sorrento

How to choose the right size

To choose the right tires for the Kia Sorrento, you need to choose the right tire size.

In the factory configuration, the manufacturer sets the standard size 235/65 R17. In addition, it is possible to install larger diameter tires on the Sorrento: R18 and R19. This can only be done in the summer season.

Friction and studded winter tires on the Kia Sorento are best used according to the manufacturer's recommendations. Considering that the tire size recommended by the manufacturer (R 17) is quite common, it is always possible to get the required tire size. This size is usually always available at tire dealers' outlets.

Tires for Kia Sorento

Attention!

When choosing a tire size, you need to know exactly the parameters suitable for a given car.

All Kia Sorento models have a bolt pattern of 5x139.7.

Another important point when choosing the right tire size is purchasing original tires. This is explained by the fact that replicas and fakes sold on the market often do not have the quality declared by the manufacturer, and the dimensions may also not be suitable. It is important to buy tires from an authorized dealer.

Several answers to questions

In conclusion, we will try to give simple and understandable answers to the most frequently asked questions.

Question 1. What wheels are best for winter tires?

Answer: It is clear that the term “wheels” here means disks, which, as is known, can be cast from steel and light alloy. From the point of view of the driving performance of the car, it makes no difference which wheels to use.

But thrifty car owners prefer to install hardware for the winter. Firstly, the beauty of alloy wheels, smeared with mud and snow, is still almost invisible.

And secondly, roads are often treated with chemicals that corrode not only the ice, but also the decorative coating of the wheels. But again, this is a personal matter for everyone.

Question 2. What pressure should the Kia Rio tires have?

Answer: It depends on the engine modification and wheel size. For cars with a 1.4-liter engine with 14 and 15 spokes, the manufacturer has set a standard of 2.1 MPa front and rear.

For 1.6-liter modifications with R16 195/55 wheels, it is necessary to pump 2.2 MPa. Lowered tires R17 205/45 inflate at 2.7 MPa each.

Question 3: Where is the year of manufacture indicated on the tire?

Answer: The date is printed on the sidewall of the tire as a four-digit number. The first pair of digits indicates the serial number of the week, and the second - the year.

Factory tire parameters

The third generation of the car was released in 2011. The car was produced in sedan and hatchback versions, in 3, 4, 5 door versions. Height, ground clearance and pitch were stable. The third generation Kia Rio tire sizes varied slightly between models. Wheels - 15 and 16 inches. The smaller size was used in cars of the previous series, the larger one was used only in amateur productions.

A feature of the 3rd generation wheels is their universal markings. In it, the parameters are encrypted using letters and symbols. The size of Kia Rio 3 tires depends on the size of the wheel. Original:

• width - 5.5J - 6.0J;
• radius - R15 or 16;
• number of mounting holes and the radius of the rim in which they are located - PCD 4×100;
• rim overhang - ET48 and ET52;
• disc hub bore diameter - DIA 54.1.

The characteristics for the Kia Rio, produced from 2013 to 2014, were noted in this order.

The Kia Rio 3 wheel size affects the tire size:

• 185/65 88H;
• 195/55 87N (for larger radius).

During restyling and improvement of configurations, only the tires and wheel width changed. The most important values ​​for replacing standard components - bolt pattern and diameter - are left unchanged by the manufacturer over many years of production, without taking into account body and engine modifications.

What is the wheel bolt pattern on KIA Rio 3 cars?

The third generation Kia Rio has a wheel bolt pattern of PCD 4×100. European indicator; indicates the position of 4 bolts on a circle with a radius of 100 mm. The parameter is determined by the manufacturer. These numbers should be used to select replacement options. That is, a 4-bolt design cannot be replaced by a 5-bolt design.

If the ratio of bolts and circumference of the original and the analogue is the same, the size of the Kia Rio 3 wheels is suitable, the analogue can be installed.

The machine has a hole for an M12x1.5 nut. The fasteners are the same for all modifications of the third generation.

To determine the bolt pattern yourself, you will need:

1. We unscrew the steering wheel.
2. Measure the distance between the centers of opposite bolts with a ruler.
3. If there are 4 on the disk, the PCD corresponds to the actual value.

For models with five bolts, the resulting figure must be multiplied by 1.05.

What non-standard sizes can be supplied?

The location of the bolts must match, but the diameter may be different. The most commonly used jet is R17 with low-profile tires. It is not recommended to install high profile tires as they will interfere with the fender if the body is modified after 2015. Replacement with R14 is allowed (if the original one was R15).

External tire size:

• width - 195, proportionality - 60, 65 (R15);
• width - 195, 205, proportionality - 55 (R16);
• 225/45, tuning 215/45 (R17).

You may not notice a slight discrepancy in the overall dimensions of the assembled Kia Rio 3 wheels. The initial value should be the same or slightly different.

The ET characteristic indicates the ratio of the surface areas of the disk and its central part.

ET48 - Positive overhang 48 mm. With a negative value on non-original versions, the wheels go into sharp turns. Significant discrepancies, as well as differences in bolt configuration, will prevent installation and fastening of a non-standard model.

Wheels for Kia Rio

There are original and non-standard options. Over several years of production, several factory disks were installed:

• Until 2015-2016 - for Kia Rio 3 with 185/65 tires - R15 and R16, cast.
• After restyling - casting of the same diameter, R15 steel (in the budget package).

For replacement, three types of models are used, which differ in the manufacturing method: stamping, casting, forging. Suitable light alloy versions: Venti 1603 and 1404, Alcasta M31, X'trike X118. For diameter 15 - NZ SH305, for R16 - VSN CV3.

Stamped models - Eurodisk X40006ST, TREBL 42B29C, OFF-ROAD 01.

What is the tire pressure

It is the driver's responsibility to constantly monitor tire pressure. This will avoid standard problems associated with vehicle operation. An abnormal pressure value often causes:

Often the car owner independently reduces the pressure on the front wheels of his own vehicle. This reduces the load on the suspension, and the car “passes” various road irregularities an order of magnitude easier. But it is worth noting: a decrease in pressure even by 0.1 MPa leads to serious problems. The main ones include:

An overinflated wheel causes no less problems. The central part of the cylinder begins to wear off quickly. In addition, at ambient temperatures of more than 60 degrees Celsius, the tire may simply explode. Which will lead to driving into the oncoming lane. Standard pressure:

The most standard pressure is in cars manufactured in 2017-2019. It is 2.3 MPa. The reason for this lies in the relatively large dimensions of the wheels, with a rim diameter of more than 15 inches.

How to carry out bolt release?

Loosening in the KIA Rio model is carried out in several stages. It is equally important to know which bolt pattern is suitable.

1. When choosing disks, we determine the entire list of significant parameters. We pay attention not only to the design, but also to other very important aspects, such as the configuration of the wheel bolts. We also determine the dimensions required for a particular machine.

Since all wheels have universal markings, confusion is likely to be avoided. You can find specific parameters of wheel models suitable for KIA Rio on the online resource.

For example, modifications of cars produced in 2013-2014 are marked as follows: “6J R15 PCD 4x100 ET48 DIA54.1.” This aspect allows the owner to obtain information about the desired disk width of 6" and radius of 15." In addition: the character set “PCD 4×100” indicates the European marking principle, indicating the number of holes and the diameter of the circles. Which bolt model fits these parameters? These specifications are a bolt pattern: four bolts with a diameter of 100 mm.

When installing a disk, one should not neglect such an important parameter as its protrusion. If this aspect has a negative value, then during maneuvers the wheels will protrude outward. When this value is too high, the disk cannot be installed.

The initial value is indicated as follows - “ET48” (for the Rio model). If the planes of the surfaces on the disk coincide with the center of the product, the protrusion will be equal to zero. For European classification: Applicable Rio wheels have a positive offset of 48mm.

2. The wheel bolt configuration is determined. This action can be performed in one of the following ways:

• when purchasing analog discs, you can take an old copy as an example and compare the geometric parameters right on the spot;
• measuring the distance (we arm ourselves with the appropriate tool) between attacks.

The last method is a last resort (if there are no old disks).

What tire sizes does the manufacturer recommend to install?

The size of wheels installed at the factory depends on two main factors: the production code and the modification of the installed motor. The best solution is to use tires that match the standard sizes set by the manufacturer. During the design, angular acceleration, distribution of weights between the wheels, and other moments were taken into account. You need to carefully read all the nuances.

For all cars produced between 2000 and 2005, without exception, the manufacturer ordered standard wheels:

The wheel diameter is 13 inches. It should be noted that the type of disks that all cars were equipped with is also standard - 5.5J×13. Departure – ET40. This size is quite common. This significantly expands the choice of wheels for upgrading your own car. from 2005 to 2022, the Kia Rio 2 JB version was produced. The cardinal difference between JB wheels and the earlier model is their larger diameter. It is 14 inches. Moreover, the overall tire dimensions remain the same – 175/70 mm. The next stage of development of this car fell on the period 2020-2020. The modification is marked with a pair of letters – UB. Drilling – 4×100 (as on other versions of the car).

An important difference between UB and earlier modifications is a larger selection of units. As many as 6 trim levels were presented. The engines differed not only in their volume, but also in their type (gasoline/diesel). Directly at the plant, as many as 3 different standard sizes were installed:

Not only the diameter, but also the size of the disks differs. In the first case, with a wheel width of 185 mm, size 5.5J×15 was used. Departure - ET36. Tires 195/55 mm were equipped with disks with a diameter of 6J×16. The latest modifications were equipped with wheels with a diameter of 17 inches. However, the drilling remained standard - 4x100. This greatly simplifies the procedure for selecting new disks.

The latest version of the Kia Rio is the fourth. Marked with the letter FB. This model was produced from 2020 to 2022. Tires of the following sizes were installed:

How to choose winter tires

Let's understand the summer season, now let's try to figure out how to choose the best winter tires for the Kia Rio. Let's say right away that they should be winter and not for all seasons.

Although the tires have the M + S badge (which means mud and snow), the rubber composition is not winter, that is, it does not belong to the category of friction tires - they cannot be driven in winter.

Therefore, it is necessary to decide which winter tires to choose, considering only the stud / clutch (Velcro) options. Where there is snowy winter, you have to drive on dirty roads, on uneven surfaces, studded tires are much more reliable.

However, experienced drivers feel comfortable with Velcro in any weather conditions. It is also less noisy, and for those who spend a lot of time driving, this is one of the main selection criteria.

Now winter is in full swing, so the stores have an excellent assortment, some with several dozen models. We present the most proven premium and economy class options.

Studded

Studless

What brands of tires are best to use?

We have come to the most pressing and most important question for practice: “Which tires are the best?” Considering that today the market is replete with different brands, prices, characteristics between tire models, it is most likely impossible to answer the stated question unambiguously.

But we will still try to give some recommendations for buying tires from a particular company and consider five, in our opinion, the best tire options. In total, two fives will be presented: for summer and for winter. As already mentioned, the choice of models was focused primarily on new generations of Rio.

Reference: prices are indicated for wheel size 195/55R16 (unless otherwise stated) and are averaged to a total value based on those in the largest thematic online stores.

Disc care

The wheels on any modern car need proper care. And the Kia Rio is no exception in this case. Listed below are several reasons why rims can fail, as well as basic principles for caring for them.

The main reasons for disc wear:

• Impact of external factors.
• Improper storage, careless attitude.
• Buying used disks.
• Incorrect tire pressure support.
• Slush and dirt.

Basics of proper disc care

Typically, cast aluminum alloy wheels perform well in the sun, but they are very poorly affected by dirt, slush, ice, sand, various chemicals, etc. It is recommended to periodically clean the wheels to prevent the destruction of their molecular composition.

What drives can be installed

Below is a list of discs that the owner of a Kia Rio can easily replace the standard ones with without any difficulty.

These wheel models were created individually for Kia Rio. This only speaks of excellent quality, compatibility and excellent fuel economy.

The Kia Rio car is one of the most popular models in Russia, so owners almost never have problems choosing wheels.

The main thing is to decide which disks are needed for certain purposes. It is not a good idea to buy used models, because they may already be defective or have an altered molecular composition. It all depends on the experience of the buyer and the honesty of the seller.

To summarize all of the above, it can be noted that budget R14 wheels are suitable for the Kia Rio I. On other versions you can install standard R15, which are sold almost everywhere. If you want to see the admiring glances of passers-by on your car, then it is recommended to purchase 16 or 17-inch wheels.

Kia Rio is a subcompact middle class car from the Korean concern Kia Motors. The model has been presented on the market since 2000. Over 19 years, four generations have been released:

• Kia Rio DC: 2000-2005;
• Kia Rio JB: 2005—2011;
• Kia Rio UB: 2011 - present;
• Kia Rio YB: 2016 - present.

In addition to four generations of the Kia Rio, restyled versions of the model were produced annually. They did not have any significant differences in technical characteristics; the interior and exterior were mostly affected. The sizes of tires and wheels remained unchanged, interchangeable between generations.

Maximum and minimum possible parameters of non-standard disks

If car owners have a desire to replace standard wheels with some others, for example, which will differ in the material of manufacture, type of production (cast or forged), you need to know what the minimum and maximum size of disks can be installed on a Kia Rio.

• R14 (cast or stamped)

This is an inexpensive option for those car owners who do not have a lot of money. These discs can only be installed on Kia Rio I generation. For other models, the minimum radius is 15.

• R15 (light alloy or stamped)

This is the standard, at least for this car model. This size is considered the most popular and widespread, so in any store you can easily find up to 40 models, so there will be no problems with the choice.

• R16 (cast)

These discs are larger in size than their predecessors and are considered to represent a certain “status” of the car owner. They have a 2nd drill more often than usual, but it will be somewhat easier to sell such wheels, because they fit car models from different manufacturers.

• R17 (cast)

The motto of young extreme drivers is: “Turn away from the classics, replace regular tires with low-profile ones and install huge wheels.” After such a decision, traffic jams will be created on the road from drivers who will want to look at a car with a given rim size.

Drilling Kia Ceed 2010

This year the car was subject to modifications and some changes. Cars of this period are quite popular and widespread throughout the Russian Federation and beyond. This year was equipped with the following wheels:

1. R15 with tire size 195/65, the disc offset is 47 mm, and its size is 15x5.5.
2. R16 with tire size 205/55, the disc offset is 51 mm, and the size is 16x6.5.

The above data also applies to models equipped with engines: 1.4L; 1.6CDRI; 1.6L; 2.0L crdi

.

All other variants were produced with the following characteristics:

• Wheel size 15x6.0, offset 45 mm, tire size 185/65R15;
• Wheel size 15x6.0, offset 45 mm, tire size 195/65R15;
• Wheel size 15x6.0, offset 45 mm, tire size 205/60R15.

For all specified configurations, the bolt pattern is 5×114.3

Recommendations for disc care

• Check the geometry and wheel balancing on a special diagnostic stand. If deviations are detected, restore the integrity of the structure at a service station. It is impossible to “reanimate” the disk on your own due to the lack of necessary equipment;
• Visit a service station for preventive maintenance if you find cracks or dents on the rim;
• Avoid getting into potholes, especially at high and medium speeds. The disk will be deformed, the seal will be broken, regardless of the material of manufacture;
• Monitor the tire pressure; it should not differ from that recommended by the manufacturer. If there is a deviation, pump it up yourself, contact the service station;
• Observe the transition to summer and winter modes. In summer, the tire pressure is 0.12 atm higher, in winter it is lower by the same amount. The parameters are specified in the vehicle operating instructions;
• Tighten the rim nuts with a torque wrench. Excessive tightening contributes to the breakage of the studs, weak - to the unscrewing of the wheel and a collision on the road.

In sunny weather, cast aluminum wheels are least susceptible to external damage. But in slush, ice, when the road is strewn with various chemicals, the rim is susceptible to corrosion. This provokes paint peeling and destruction of the molecular composition.

Wash your wheels as they get dirty. Since it is unlikely that you can clean it properly with a rag, use high-pressure compressors. Equipment of this class is available at many service stations, workshops, and service centers.

Systematic polishing removes scratches. First clean the wheel from dirt, dry it thoroughly, and then treat it with a chemical. Wipe with a cloth several times.

Store wheels in a hanging position, do not stack them on top of each other. Clean off any dirt, dry, and wrap in cellophane. Practice applying the spray to the surface of the disc before storing.

The average service life of original wheels is 160 – 190 thousand km. Subject to a moderate driving style, the replacement interval will increase by a third. The service life of tires is half as long as disks. Do not forget to check the camber-toe angle, since the speed of wear of the rubber tread depends on this.

By installing new stamped (also known as stamping) or alloy wheels on your car, you can transform its appearance, thus giving individuality and independence to your car. The configuration of the KIA Rio will determine what type of wheels the car will leave the dealership with. For the Comfort and Luxe trim levels, the manufacturer offers stamped steel wheels R15 with original caps. And the more expensive Prestige and Premium trim levels are equipped with cast alloy wheels R15 and R16. You need to take into account the tire size, for example, for R15 185/65 is suitable, and for R16 you need to take 195/55. When choosing new shoes for your Kia Rio, you need to take into account the typical wheel size suggested by the manufacturer for a particular make and model of the vehicle. Since the size does not match, I provoke an excessive load on the suspension, thereby reducing its service life.

The parameters of cast and steel wheels will be as follows:

Next, you need to decide which one to buy, analogue or original?

There is no clear opinion on this matter. Since some believe that the original wheels will last much longer and be safer. But others are confident that current copies of wheels are no worse in use than the original ones, and differ only in the absence of a serial number. For a clearer picture, you need to understand that the original rim has a certificate from the manufacturer along with the car and its own serial number. As for non-originals, the quality can be very different.

A reasonable solution for many car owners may be to purchase steel wheels for winter tires, so that in winter the original alloy wheels do not deteriorate from salt sprinkled on the roads. By the way, this can save money, since you don’t have to change your tires every season at a tire shop.