How to program a key fob for an Alligator alarm: setup and operating instructions

Author: Victor

Setting up key fobs for the Alligator alarm depends on the model and functions of the system, but regardless of the type, it begins with binding to the control unit. Programming is carried out according to one algorithm using the Vallet service button. If it was not possible to program the remote control in this way, then you need to contact a service center, since more modern Alligator key fobs sometimes require manual registration of the code.

[Hide]

Where is the Alligator alarm wiring diagram?

The LED will start flashing in a series of 7 flashes after a pause. In any other mode there is no load on the line.

The block is secured with two screws or plastic braces. The system will arm this circuit 3 seconds after it stops being active.

Under the hood there is also nothing complicated, again the mounting plate from the activators, a limit switch on it, a plate on a self-tapping screw to the wing from the inside will help. Orange wire. When exiting programming mode, you will hear one long siren signal and the system LED will go off. If you need to extend the wires for connection, then the contacts should be connected inside the car, in the driest place, to prevent their oxidation. It is definitely worth considering that the temperature sensor must be attached to the rubber part of the radiator.

Many new vehicles have low-voltage or multiplex systems that can be damaged when using low-impedance test equipment, such as test lights or logic probes that are used to test computers.
The green-yellow wire has many options for where to connect, and for opening doors, on the engine blocking relay, an output for closing windows. The LED will flash in a series of 4 flashes after a pause. It is best to place the impact sensor on a hard surface of the bulkhead that separates the passenger compartment from the engine compartment. You will hear 2 short beeps from the siren, confirming that the factory settings have been restored and you are exiting the function programming mode. Similar publications:. After it starts, the voltage will increase to 7 V or more. This is due to the fact that moisture can cause oxidation of the contacts, which will lead to certain difficulties in operation.

The LED will flash in a series of 16 flashes after a pause. The installation location must be hidden, but the consumer must always have access to the device from the driver’s seat.

Specifications

How to use starline b9 alarm key fobs
Description of the technical characteristics of this alarm model:

• transmission of pulse signals is carried out via a radio channel with an operating frequency of 868 MHz;
• to power the security system, an on-board network with a voltage of 12 V is required;
• protection of power lines is carried out using safety devices rated 5-30 amperes;
• when the protection mode is turned on, the car alarm should consume no more than 15 mA;
• the maximum number of alarm cycles when the anti-theft system is activated is 6;
• duration of siren signals - 30 seconds;
• the operating range of the pager depends on weather conditions and the presence of interference in the area, on average this figure is 700 m;
• The memory of the alarm control unit allows you to register no more than four key fobs.

A brief overview of the characteristics and features of the Alligator S-825 RS car alarm is given in the video of the “Everything Affordable” channel.

Video

Point Black talks about the process of choosing a reliable signaling model from the Alligator company.

Do you have any questions? Specialists and readers of the AUTODVIG website will help you ask a question

Was this article helpful?

Thank you for your opinion!

The article was useful. Please share the information with your friends.

Yes (60.00%)

No (40.00%)

X

Please write what is wrong and leave recommendations on the article

Cancel reply

Rate this article: ( 5 votes, average: 4.60 out of 5)

Discuss the article:

Types and models of Alligator alarm key fobs

Settings for the alligator alarm

General characteristics of Alligator keychains:

• The battery in the main remote control is used at 1.5 volts, in the additional one - 3;
• the main key fobs have a button blocking function from accidental pressing;
• signal transmission frequency 433-868 MHz;
• car search;
• panic mode - siren and alarm signals are activated;
• option to call the car owner from the salon;
• Anti-Hijack - protection function against robbery;
• Valet mode to disable all security functions of the anti-theft system.

Table of models of Alligator security system control panels and their main characteristics

Pros and cons of the remote

Advantages of the Alligator car alarm key fob with auto start:

1. Remote setting of the anti-theft system. The user has the opportunity to change the parameters of the alarm functions from the key fob without interacting with the service button located in the car interior.
2. Availability of two-way communication. Transmitting information online between the remote control and the system allows the car owner to remotely receive all the necessary information about the state of the complex and the alarm level.
3. Automatic engine start. This function remotely activates the operation of the power unit, warming up the internal combustion engine without wasting the user’s time.
4. Ergonomic and shock-resistant housing.

Disadvantages of the control panel:

1. Fast battery discharge. Despite the fact that the device uses low power consumption technology, the key fob batteries must be changed at least once a month. In addition, the galvanic cell is inconvenient to remove and install due to the shape of the communicator body.
2. Functions malfunction. On some remote controls, the alarm setting modes function incorrectly and intermittently. The problem is solved by returning to factory settings.
3. Instability to external damage. During operation, many scratches form on the body of the key fob, which worsens its appearance, but does not affect the operation of the device. In order to avoid this problem, you need to purchase a cover.

How to install?

Starline b9 alarm review

Installation Alligator 825:

Before starting work, it is advisable to turn off the power to the on-board network. But this does not need to be done if the car has an audio system with a programmed code. There is no need to disconnect the battery if the car is equipped with airbags. To prevent battery discharge during connection, we recommend removing the safety device and the interior lighting circuits. Remove the steering column trim and dismantle the instrument panel. Depending on the machine, it may be fixed differently. Usually the device is attached using self-tapping screws; they need to be unscrewed with a screwdriver. After removing the control panel, select a location to mount the processor module. It is advisable that it does not come into contact with electronic devices or other wires, as this may lead to malfunctions of the Alligator 825. The module is fixed using self-tapping screws, glue or double-sided tape. Mount the antenna module on the windshield. It should also not be mounted near electrical wires or devices that may emit interference. Study the diagram that is included in the package, as well as the installation kit of wires for connection. Using a multimeter, test the wires that run under the left threshold of the car and the driver's door

Please note that the cable colors match. There is a parking brake indicator on the dashboard connector. You need to make sure that it is working correctly - ring the electrical circuit to which the sensor is connected

At the same stage, we recommend checking the generator device by ringing. This will allow you to correctly connect the wires necessary to ensure the operation of the internal combustion engine. Similar actions are performed with checking the contacts on the ignition switch. These outputs will be used to autostart the internal combustion engine. The limit switch and siren are mounted in the engine compartment. The limit switch is installed on the metal surface of the body; it will be a mass. When choosing a location for mounting the switch, you must take into account that the device should not be exposed to moisture, as it will destroy the device. The switch is mounted using a bracket. The siren is installed secretly, away from the engine. The wires from these devices are routed into the car interior. The installation of the shock sensor is carried out in the cabin; screws or ties are used for fixation. Regardless of the type of mount, the consumer should always have easy access to the controller so that it can be adjusted if necessary. The diode light bulb is placed in the area of ​​the windshield of the passenger compartment. The temperature controller is installed on the body of the power unit or on another metal surface adjacent to the motor. The cable from the device is routed into the interior. The immobilizer is being installed. The engine immobilizer must be connected to the security system. The wires are laid, all elements are connected to the microprocessor unit in accordance with the instructions for the Alligator S-825RS alarm system.

The installation of this “signaling” model is shown in the video filmed by Anton Bobkov.

Equipment

Alligator S-825RS kit
Devices and elements that are included in the system with autostart and dual communication:

• main key fob, equipped with five buttons and having a display that allows feedback to work;
• a spare remote control, it does not have a display, the case is equipped with four buttons;
• a set of connectors for connection and installation, each plug is equipped with a cable for connection;
• microprocessor module, required to control the system;
• sensitivity controller;
• siren in the amount of one piece;
• an antenna module equipped with a transceiver is supplied with a cable and connector for connection;
• temperature sensor for installation on the motor;
• blue diode light, used to monitor the condition of the machine;
• a special switch used to enter the service mode;
• mounting kit for installation;
• instructions for installation and use of basic functions.

The Automotive Products Unpacking channel talked about the operating features of the Alligator 825.

Let's move on to installation and configuration

The original Alligator car alarm, the operating instructions included in the delivery package, must be selected taking into account the age of the car, its electrical circuit and model. Take into account the manufacturer's advice. Quick setup of the Alligator car alarm is possible at an authorized service center. Here they will talk about “+” and “-”.

The manufacturer's comments indicate that random activation is due to improper maintenance or incorrect configuration. Installation is carried out in an authorized salon. Attempts to perform installation on your own will result in an increased risk of theft.

Advantages and disadvantages

What are the advantages of the Alligator alarm:

1. Warning the car owner by turning on the siren, as well as sending appropriate signals to the device control panel.
2. A large assortment of different models will allow the consumer to choose an Alligator car alarm in accordance with their desires and financial capabilities. Reviews show that, even if the “alarm” has a low price, it will still perform its function efficiently.
3. Reliable protection circuit. Using secure communication channels helps prevent car theft.
4. Almost all models include an ergonomic and easy-to-use remote control that allows you to configure and control the main components of the vehicle.
5. Alligator machine alarms fully meet international standards of quality and reliability.
6. The device comes with a service manual, which describes in detail the process of installing and connecting the alarm.

What disadvantages will a car owner have to face:

1. The system does not work when the key fob button is pressed. The reason may be that the battery in the remote control is low, so the car owner needs to emergency turn off the alarm and replace the battery. The shutdown procedure is performed using the service key. If the reason for the non-working condition lies in the key fob itself, then the device must be replaced. A malfunction of the control module can only be resolved by specialists.
2. When trying to arm the car, the car doors do not close. The cause may be related to the safety device or the non-functional condition of the door locks. It is better to entrust the solution to problems of this kind to professionals.
3. The car alarm goes off on its own. The reason may be that the sensor is not configured correctly. Controller diagnostics required. If the device is not working, it must be replaced.

Instructions for use

The advantage of Alligator anti-theft systems is their ease of installation and configuration. Each model has detailed instructions that allow you to install and configure the alarm yourself.

How to connect?

Before starting installation, it is necessary to study the electrical circuits of the car and the possibility of connecting an alarm system to them. To do this, you need to study the instructions supplied with the device, which contain connection diagrams. The next step is to prepare the main unit for connection. During connection, you must disconnect all wires that are not needed for further installation. At the final stage of preparatory work, you need to check the performance of the car itself.

Direct installation consists of a sequence of steps:

1. First you need to remove the panel, which is necessary to connect the anti-theft system.
2. Next, you need to place the device in a secret place, not far from the compressor, and connect the wires and control sensors one by one to the car mechanisms according to the diagram in the instructions.
3. Then you need to attach the antenna. It is mounted either on the side of the windshield or on the body of the car.
4. Next, you should install it in the engine compartment of the car.
5. At the final stage, you need to return all removed components to their place.

To connect the wires, you should use the instructions, which clearly indicate their location according to the color scheme. The wires must be connected according to the diagram attached to the instructions. Contacts should be cleaned thoroughly.

How to setup?

The security system is activated using the control panel.

Setting up the key fob includes the following steps:

1. First, turn on the ignition.
2. Next, you need to press the service button with an icon in the shape of a closed lock. When you press this button the car should flash.
3. Then, pressing the service button, you need to hold it in this position for several seconds. The alarm will be partially activated.
4. Then press this button three more times.
5. After waiting for the signal, you need to press each button on the key fob in turn.
6. Next, you should try to disable the security system using the remote control. The dimensions should flash again.
7. To check the autorun operation, you need to click on the “Smart Start” button. With its help you can turn off the engine.
8. Now you can turn off the ignition.

Thanks to the described steps, the alarm system will be configured. You also need to adjust its sensitivity using sensors and instructions.

This video demonstrates the step-by-step installation of the Alligator anti-theft system on the Lada Largus (author - Karabas Barabasovich).

Reprogramming and flashing

It happens that the key fob freezes and refuses to carry out your commands. As a solution, you need to reset the settings and restore the firmware. Or you can program a second, spare remote control. In order to properly reflash the transmitter, do this.

1. Press the “Jack” service key once. The ignition must be turned off.
2. After that, click “Valet” three more times. The siren will sound.
3. Click the buttons on the pager one by one, synchronizing them with the control unit.
4. Turn the ignition on and off immediately. Check the functionality of the key fobs.

Malfunctions

There are different types of malfunctions, but the most common ones are:

1. The alarm doesn't respond and nothing happens when you press the key fob. In such a situation, first of all, you urgently need to remove the alarm using the service button, then check and replace the battery. If everything is fine with the batteries, then most likely the fault is in the key fob itself, then it’s better to buy a new one (two key fobs are almost always sold in the package).
2. The alarm does not close the car doors. Most likely, there is a malfunction in the door lock or the alarm fuses have failed; it is better not to delay with such a problem and contact a service center.
3. The alarm goes off on its own from time to time. First of all, adjust the alarm sensitivity. If this does not help, then try changing the location or replacing the shock sensor; replacing it with a working sensor almost always helps.

How to determine the alarm model by key fob

The manufacturer's alarm model Alligator can be determined by the description of the appearance of its key fob:

1. TD-350/355. Remote controls in this series have a vertical screen orientation. The device is equipped with a non-removable antenna, which is part of the housing. The keychain is made in silver with black edging.
2. D-910. The communicator has a small screen, the area of ​​which does not exceed 1/3 of the front panel of the key fob. The device has a removable black plastic antenna and a body with round silver inserts.
3. S-800/825/850/875. The key fob features a horizontal screen orientation with a white backlight. The body is made of dark gray plastic and equipped with a built-in antenna. This security system, unlike others, has the function of auto-starting the engine based on voltage, so the display has a characteristic icon in the form of a lightning bolt.
4. TD-320. The device has a black body with a thin silver insert around the display and an enlarged eyelet for attaching to a keychain. The remote control screen has a vertical orientation and is distinguished by a large lock icon in the middle.

Photo gallery: Alligator security systems

Photos of alarms with feedback from the Alligator company.

Alligator D-910

Alligator S-800

Alligator TD-320

Alligator TD-350

Photo gallery

1. Remote control model D-1000RSG

2. Signaling model SP-55RS

3. Keychain from model TD-350

Price issue

The cost of the most affordable model NS-405 is about one and a half thousand rubles. The S-300 model will cost the buyer approximately 7,700 rubles. The S-500 CAN anti-theft system costs around 13,500 rubles. The average cost of more or less functional models is 5-8 thousand rubles.

The best models under the Alligator brand

The interest of ordinary car owners in reviews of new alarm systems from various companies, oddly enough, does not fade with the development of sanctions hostility. The choice of car alarm models of various brands that have not yet been discontinued is increasing day by day. What should an ordinary car owner, inexperienced in electronics and the Internet, do? Online:

• advertising and sales articles about new anti-theft products;
• reviews and reviews about alarms - purchased from incompetent rewriters;
• on the forums - questions from amateurs about alarm malfunctions and rare reviews of self-taught automotive specialists.

This review of the best Alligator alarm models is an attempt to fill, at least a little, this gap. Moreover, many similar models have been produced:

Car alarm Alligator series C-200

• reliable two-way communication;
• coding using technology not available to Keeloq code grabbers;
• compact, antennaless alarm key fob;
• control signal range 1200 m;
• interior, antenna unit with LED indicator;
• function of an active immobilizer;
• presence of a turbo timer;
• security with the engine running;
• the cost of the alarm is 4890 rubles.

Car alarm Alligator series C-300

• stable two-way communication;
• anti-grabber coding "Keeloq";
• the range of action of the alarm control command is 1200 m;
• autostart system from the 1st button (by time, by temperature);
• ergonomic, multifunctional key fob with indication of time, timer, battery charge, engine start, interior temperature;
• the cost of a car alarm is 6,770 rubles.

Car alarm Alligator series C-500

• unconditional two-way communication;
• anti-grabber, security coding “B-Dialog SST”;
• car alarm operating range up to 3 km;
• highly informative keychain with ticker;
• programmable autostart;
• turbo timer;
• the cost of a car alarm is 11,530 rubles.

Car alarm Alligator series TD-350

• noise-free two-way communication;
• control distance 2000m;
• conversational coding;
• availability of additional channels for connecting a CAN module;
• possibility of using the BILARM GSM communication module;
• service ability to call the owner;
• autostart;
• protection when the engine is idling;
• remote temperature control in the engine area;
• automatic control of the transmitter - search for the driver;
• the cost of the alarm system is 6,760 rubles.

Car alarm Alligator series SP-75RS

• reliable two-way communication - operational at a distance of 1200 m, in command mode - 800 m;
• dialogue coding "DUPLEX DIALOG";
• the alarm has an intelligent control function;
• autostart system;
• applicable to any car engine and gearbox;
• possibility of using the BILARM GSM communication module;
• Alligator alarm system SP-75RS series has additional channels for connecting a CAN module;
• works with car engine start button;
• remote diagnostics of sudden engine shutdown;
• the cost of the alarm system is 6,660 rubles.

You can always choose the best thing that a particular car owner would like to have from many dozens of Alligator alarm models. One-way communication and dynamic coding are enough for one, while two-way communication and conversational coding are not enough for others. The BILARM GSM module together with the GPS module will be just right for this. Thanks to the rich possibilities in choosing characteristics and their successful combination, Alligator car alarms have become the best-selling security systems in recent times.

Instructions for setting up key fobs M, D, S series

Security system M, D, S series (A1, C300, A2, NS 505, A1S, S825 RS, A2S, D1000, 868, C2, SP75 RS, C 2C, S400, A 3 S, A 9, TD 350, A 3, S 3S, M 1500, S 5, M 700, S 500, s 725 rs, 325 2 buttons, D910, S 250) allows you to record up to four transmitters. But you can only use two five-button or four-button ones. When binding, previously stitched key fobs are deleted from memory.

If you use a system shutdown using a secret code, follow these additional steps.

Let's move on to installation and configuration

The original Alligator car alarm, the operating instructions included in the delivery package, must be selected taking into account the age of the car, its electrical circuit and model. Take into account the manufacturer's advice. Quick setup of the Alligator car alarm is possible at an authorized service center. Here they will talk about “+” and “-”.

The manufacturer's comments indicate that random activation is due to improper maintenance or incorrect configuration. Installation is carried out in an authorized salon. Attempts to perform installation on your own will result in an increased risk of theft.

Why program remote controls?

The question of how to bind and how to set up an Alligator alarm may arise in the following cases:

• Broken old remote control.
• Lost key fob.
• The appearance of an additional driver who needs an individual control device.

Regardless of the goals, the binding occurs according to the algorithm discussed above.

How to enable autorun

Autorun is configured according to the generally accepted instructions for Alligator models using the following methods:

In addition, the user can independently choose the warm-up time or specify the time interval after which the system will start working.

Before starting the system, you must ensure that the basic operating rules are followed:

1. The car must be parked, but on the street, and not in a garage or underground.
2. The parking brake must be engaged.
3. On a car with a manual transmission, the shift lever is fixed in the neutral position. If the car is equipped with an automatic transmission - in the parking position.
4. The fuel tank must be filled.
5. You cannot activate remote start if there is a passenger or animal inside the car.

Autostart by time

To configure autorun by timer (time interval), you must perform the following steps:

1. Hold down the snowflake button for 2 seconds. After this, a sound signal will sound, which will confirm successful entry into the settings menu.
2. Hold the “locked” button until the clock appears on the screen and the turn signals flicker. They should blink once. There will also be 1 signal from the key fob.
3. To change the values ​​of the time interval after which the system will try to turn on autostart and start the engine, you need to press the button with the “snowflake” the required number of times. Each subsequent fact of pressing will be accompanied by 1 light and 1 sound notification.
4. To exit settings mode, you must wait 15 seconds and do nothing.

Autostart based on temperature

Activating automatic start based on temperature is easy. To do this, you need to press the key with the snowflake symbol for 2 seconds until one sound alert sounds.

Next, you will need to release the key and hold the “open lock” - after this another sound will be heard, and a thermometer indication will appear on the system monitor. Then press the button again and the key fob will make a short sound.

To exit settings mode, you just need to do nothing. There are no difficulties with activating autostart based on temperature.

How to disable autorun

Despite the great popularity of the automatic start function, in certain circumstances it becomes necessary to turn it off on the Alligator alarm system. Sometimes car owners consider the option to be ineffective and even worsen the vehicle’s resistance to burglary.

To disable autorun, you will need to take the following steps:

1. First of all, you need to carefully read the step-by-step guide and find the best shutdown option. There are generally accepted methods that are suitable for most models, but sometimes they differ.
2. Advanced models support the software function of deactivating the automatic launch with the “on/off” lever. To turn it off, just move it to the desired position.
3. In the absence of such a function, you can select the stopping time by comparing it with the engine starting time.
4. If the alarm system provides the ability to install an immobilizer, the driver only needs to move a short distance from the vehicle, moving away the key fob. You can also place the communicator in a metal box and take it away from the car.

If the above options do not give a positive result, you will need to seek help from specialists and reprogram the system. If difficulties arise, it is better to go to a service center and carefully study the instruction manual.

Source

The principle of operation of an alarm system with auto start

Automatic start of the Alligator alarm is a universal function that can be used on different vehicles with both gasoline and diesel engines, regardless of the type of gearbox.

Modern car alarms use two autostart methods:

• Manual remote.
• Auto.

The first option involves pressing the corresponding key on the communicator, in which the key fob is used. The range of the device is 300-350 m. Even the latest models support control using a mobile application.

The possibility of automatic entry is necessary in cases where the driver is far from his car. The function involves starting the engine without direct action by the car owner after a specified time interval, upon reaching the specified temperature and other parameters.

When the car owner gives a signal, the starter is turned on, and the car emits several warning lights with turn signals. The key fob displays an indication of a successful start.

If the power plant does not start the first time, the equipment will make a couple more attempts, forcing the starter to make more revolutions.

The Alligator alarm system contains several working parts that operate using advanced technologies. They are adapted to aggressive operating environments and are not afraid of exposure to the cold. To ensure maximum comfort of use, the manufacturer equips the alarm with an automatic heating function, which is triggered either through the key fob or after a specified time.

The basic kit with alarms contains the following components for installation:

• Communicator (key fob).
• Block.
• Antenna with transmitter.
• Immobilizer.

The system is installed on the dashboard, and sensors and wiring are connected in turn to each working element. The side of the windshield or the body can be used as a mounting location for the antenna.

The main advantages of the function include:

1. Remote access to vehicle operating units and systems. Feedback support allows the car owner to remotely change basic functions without getting close to the car.
2. Ability to monitor the status of security functions. Thanks to 2-channel communication, the driver can always assess whether the anti-theft system is working and which zones are working.
3. Support for remote engine start, which is especially useful in the cold season, when there is a need to warm up the interior.

Operating modes

The driver will have to choose one of three operating modes. The first is “panic”, which triggers an audible alert. Press the lock open/close button. Pressing again will turn off the alert. The second mode is Valet, which disables the autostart of the Alligator system, for example, during maintenance or repairs. The activation process is as follows:

• turn on/off the ignition;
• hold the Valet button on the key fob for 4-5 seconds;
• wait for the sound signal;
• Check that the activity indicator is turned off.

The third mode, as mentioned earlier, is Antihijack. Blocking the electrical circuit will prevent the thief from getting far. As soon as the system detects penetration, the engine is promptly blocked. Automatic shutdown and autostart of the Alligator system, with instructions on how to start it from the key fob, you can find out the details, allowing you to quickly intervene in the process.

Car alarms are suitable for domestic and foreign cars. It is selected taking into account the required level of protection, set of options and characteristics of the vehicle’s electrical circuit. The ergonomic keychain of the Alligator system and its instructions allow you to quickly understand the functionality. Depending on the modification, the control panel is equipped with an LED screen that displays the operating parameters of the power unit. The systems are purchased and installed at an authorized center. You can perform the adjustment yourself, based on actual operating conditions.

Key Features

Main options and capabilities of the complex:

1. Automatic and remote starting of the car engine. The option will be useful for car owners who are often late for work in the morning. Its activation will allow the power unit to warm up while the consumer is getting ready at home. Automatic start can be programmed based on temperature. It is possible to start the engine from the pager button.
2. Sound and vibration warnings. The communicator is equipped with a speaker; when the siren or one of the security zones is triggered, the device display will display the alarm status indicating problem areas. This will allow the car owner to learn about possible malfunctions in a timely manner. If audible warnings are not needed, you can set the vibration to work.
3. Anti-robbery option. This is an intelligent function, its purpose is to block the engine in the event of a robbery against the car. If the car owner is forced to leave the cabin, after which the car is stolen, the engine will automatically be blocked by breaking one of the electrical circuits after a certain time. In particular, when the car moves away to a safe distance from the car owner. This function is activated under certain conditions, for example, when the brake pedal is pressed sharply, the parking lever is turned on, etc.
4. Protection against false positives. A dynamic communication channel is used to send packet data between the console and the processor module. The technology by which it was developed made it possible to ensure maximum protection of the communication channel from interference. This prevents possible signal interception.
5. The ability to remotely check the temperature under the hood of the car and in the cabin. This is available after proper installation and configuration of the appropriate sensors. If necessary, the consumer can remotely check the voltage in the machine's electrical network. Diagnostics is carried out through a processor device that tests the battery by measuring voltage.
6. Comfort function. Allows you to control door locks and the alarm mode without using a pager. The car owner only needs to approach the car, after which the system will turn off automatically.
7. The capabilities of the system include the range of operation of pagers. The main remote control can transmit a signal to a microprocessor device at a distance of up to two kilometers if there is no interference in the area. The range of the spare communicator is one kilometer.

AvtoGSM spoke about the main functions and capabilities of the Alligator 825 security system.