How to attach a key fob to an alligator alarm

Alligator alarm key fobs of various models and functions are configured in a special way, but only after binding to the control unit. Recording of remote controls in the memory of the anti-theft system is carried out according to one algorithm, using the “Valet” key. Up to four pagers can be programmed. If for some reason programming fails, you should immediately contact the service center. After all, more modern models of Alligator remotes require manual code entry. We will discuss in more detail how to attach a key fob to an Alligator alarm later.

We also have a Tomahawk 9020 instruction manual.

Programming the Alligator key fob

How to set up an alarm

At the final stage, the question arises of how to configure the Alligator alarm key fob. Before pairing your device, do the following:

Remove the original packaging from the device.
Open the battery compartment.
Make sure that the remote control is in an area of stable visibility. Please note that the display has at least two bars indicating good connection quality.

After tying, you can turn on the Alligator alarm key fob and check the operation of all systems. To do this, open/close the car, turn on auto start, set it to alarm, check Panic mode and other available options. If necessary, configure the autorun option. For this:

Press and hold the snowflake button F until a beep appears.

To program a timer start, use buttons 1 and 2 to select the desired dial icon.
Click F again, and then use buttons 1 and 2 to set the desired timer time.
Set up engine autostart based on temperature. To do this, point at the images with a thermometer using buttons 1 and 2 and confirm the action by pressing F. Using the same principle, you can program the temperature parameters. And if necessary, you can remove the timer.

Knowing how to bind, configure and turn on the Alligator alarm, you can easily configure the security system key fob and avoid errors in its operation. In the comments, share your programming experience and the difficulties you encountered.

Instructions for setting up key fobs M, D, S series

Security system M, D, S series (A1, C300, A2, NS 505, A1S, S825 RS, A2S, D1000, 868, C2, SP75 RS, C 2C, S400, A 3 S, A 9, TD 350, A 3, S 3S, M 1500, S 5, M 700, S 500, s 725 rs, 325 2 buttons, D910, S 250) allows you to record up to four transmitters. But you can only use two five-button or four-button ones. When binding, previously stitched key fobs are deleted from memory.

Disarm the vehicle.
Within fifteen seconds after deactivating the ignition, press the “Valet” key three times (non-coded mode is selected).
The siren will sound once. The LED will flash quickly. The control unit is ready to record remote control codes.
Briefly press the F button on the communicator. D series transmitter – hold F for a while.
A long siren signal will follow – programming has been successfully completed.
Use the same principle to register the rest of the keychains.
Do nothing for fifteen seconds or remove the keys.
Wait for one long and short siren signal. You have left programming mode.

If you use a system shutdown using a secret code, follow these additional steps.

Switch the ignition “On” - “Off”.
Complete this step in fifteen seconds. Click “Valet”, the number of clicks is the first value of the service code.
Click the ignition “On” - “Off”.
Also enter the second number of the password.
Crank the ignition.
Perform transmitter programming.

Operating modes

The driver will have to choose one of three operating modes. The first is “panic”, which triggers an audible alert. Press the lock open/close button. Pressing again will turn off the alert. The second mode is Valet, which disables the autostart of the Alligator system, for example, during maintenance or repairs. The activation process is as follows:

turn on/off the ignition;
hold the Valet button on the key fob for 4-5 seconds;
wait for the sound signal;
Check that the activity indicator is turned off.

The third mode, as mentioned earlier, is Antihijack. Blocking the electrical circuit will prevent the thief from getting far. As soon as the system detects penetration, the engine is promptly blocked. Automatic shutdown and autostart of the Alligator system, with instructions on how to start it from the key fob, you can find out the details, allowing you to quickly intervene in the process.

Car alarms are suitable for domestic and foreign cars. It is selected taking into account the required level of protection, set of options and characteristics of the vehicle’s electrical circuit. The ergonomic keychain of the Alligator system and its instructions allow you to quickly understand the functionality. Depending on the modification, the control panel is equipped with an LED screen that displays the operating parameters of the power unit. The systems are purchased and installed at an authorized center. You can perform the adjustment yourself, based on actual operating conditions.

How to register remote controls for Alligator L models

The Alligator L pager, which has 4 buttons, can be linked as follows.

Disarm the car. Turn on the ignition.
Press the Jack key three times. The siren will sound once and the LED will light up once. The control unit is ready to record a new control panel for channel 1.
Press key 1 or 2 on the remote control to tune to channel 1. A long siren signal will sound, indicating that programming is complete.
Turn on the "Jack" button once.
One sound will follow and the LED will light up twice. Channel 2 will be programmed.
Press the remaining button on the communicator (if you used key 1 or 2, you cannot press it again). The siren will emit a long signal - channel 2 programming is completed.
To exit the recording mode, turn on the ignition or press “Valet” twice.
The siren will sound for a long time.

L Series Binding Features

It is possible to program the key fob in the L series security system as follows:

Disarm the car.
Sit in the driver's seat.
Turn on the ignition.
Move the “Jack” switch three times from the off position to the on position.
Wait for one siren signal. The indicator will flash once. The programming mode will turn on, allowing you to configure the control of Channel 1.
Press button 1 or 2 on the key fob. The selected key will control the first channel.
A long alarm signal will confirm that the alligator key fob has been successfully registered.
Change the position of the Valet switch once.
Wait for a long beep.
Check that the indicator flashes twice.
Start programming the second channel.
Press and hold the remaining unregistered button.
Wait for a long sound of the siren.
Wait 15 seconds. You can speed up the deactivation of the programming mode by turning off the ignition or double changing the position of the “Valet” switch

When binding the Alligator alarm key fob, regardless of the series, it is important to complete each action within a 15-second interval.

Otherwise, the programming mode is automatically deactivated. To reflash the key fobs, in this case, you need to start all over again.

Subscribe so you don't miss anything important

Content

We also have a Tomahawk 9020 instruction manual.

Reprogramming and flashing

It happens that the key fob freezes and refuses to carry out your commands. As a solution, you need to reset the settings and restore the firmware. Or you can program a second, spare remote control. In order to properly reflash the transmitter, do this.

Press the “Jack” service key once. The ignition must be turned off.
After that, click “Valet” three more times. The siren will sound.
Click the buttons on the pager one by one, synchronizing them with the control unit.
Turn the ignition on and off immediately. Check the functionality of the key fobs.

Open loop switch replacement

The binding of a transmitter with one-way communication is carried out according to the following scheme.

Disarm the car.
Turn off the ignition. Press the "Jack" key once.
Click “Valet” three times, the system will beep.
Press the switch keys one by one, synchronizing them with the alarm control unit.
Turn the ignition on and then turn it off. Check the operation of the switches.

How to enable engine autostart using the Alligator remote control

The Alligator alarm kit includes two remote controls: a five-button and a four-button. The engine can be started from either a 5-button or 4-button key fob. To do this, you need to know the sequence of keystrokes.

The Alligator anti-theft system allows you to independently set the auto start of the car based on temperature, control the warm-up time, and adjust the time for automatic engine start and stop.

Enter service mode by holding the F key for two seconds on the main pager. The screen will turn on and a beep will sound.
Press F again, the display will show “timer”. CHIRP will follow.
Select the desired time period in hours (1-2-3-4-6-24). Each press will be accompanied by a squeak and the turn signals will activate.
Select temperature trigger mode. The “tempo” symbol will appear on the screen. The key fob will emit a melody and the turn signals will blink. Select the required autostart temperature (-10, -15, -20, -25).
To exit, press the F key for two seconds. After exiting, the symbols for the selected functions are activated on the display.
To disable autorun, reset the values in the menu.

Is it worth installing the alarm yourself?

The presence of a connection diagram allows you to install the Alligator car alarm yourself. In addition, to successfully complete the task, you must have skills in installing electrical wiring, plumbing tools, perseverance and accuracy. Having minimal knowledge is usually not enough, because even experienced electricians do not always take on the task of connecting such equipment.

Pros:

minimum expenses;
understanding of all processes, ease of maintenance and repair;
the ability to create different blocking and triggering modes to increase efficiency;
Increased uptime (with careful installation).

Minuses:

installing an Alligator alarm with auto start yourself is a difficult task for beginners;
large amounts of time (even with experience);
possible loss of warranty on the car if something goes wrong.

It is not advisable to install expensive Alligator alarms with your own hands, because you need to have special tools and disassemble many elements in the cabin. If you have a new car, it is also better to entrust the installation to specialists (even if there is a connection diagram).

Connecting a new car alarm pager with feedback

Synchronization of the control panel of the Alligator anti-theft system is performed according to the following algorithm.

Turn off security mode. Turn on the ignition.
During the allotted period of time (fifteen seconds), turn on “Jack” three times. The system will emit three siren sounds and the LED will flash slowly.
Click the “closed lock” button on the remote control. A long CHIRP will follow. The transmitter will make one sound.
Repeat the previous step for the remaining key fobs.
Exit recording mode by turning off the ignition or doing nothing for fifteen seconds. You will hear a short and long siren signal.

Buy key fobs for alarm Alligator

Cost of control panels for the Alligator security system of various models:

Name	price, rub.
Keychain Alligator TD-350	1200
Keychain Alligator TD-355	1300
Keychain Alligator S-800	1200
Keychain Alligator S-825	1400
Keychain Alligator S-850	1450
Keychain Alligator S-875	1400
Keychain Alligator D-910	800
Keychain Alligator TD-320	1600
Prices are relevant for three regions: Moscow, Chelyabinsk, Krasnodar.

Programmable functions for your alarm

Alligator allows you to program the following features:

service: automatic door locking based on a tachometer signal or when the ignition is turned on, unlocking the car based on tachometer readings, protection against false alarms, etc.;
security functions: activation of protection with or without locking doors, passive engine blocking, activation of Anti-HiJack mode and more;
Remote engine start: starting the car based on temperature, time. Special mode for turbocharged cars and more.

Common problems and their solutions

Knowing how to turn on the autostart on the Alligator alarm system does not always allow you to start the engine the first time. There are situations when autostart does not work due to technical breakdowns of the machine or configuration errors. Consider the following points here:

Auto start by time/temperature does not work due to disabled alarm.

The pressure sensor and indicator are not functioning.
The tachometer does not work.
The trunk, doors or hood are not closed.
The gearshift knob is not in the correct position.

Autostart time has expired.
The handbrake is not applied.

In most cases, the problem can be solved by installing a handbrake, arming the car, etc.

Knowing which button is responsible for autostart on the Alligator, you can always start the car from the key fob. Alternatively, you can set the temperature/time automatic start so that the device operates automatically.

Sources

https://autodvig.com/alert/brelok-dlya-signalizatsii-alligator-72397/
https://remontautomobilya.ru/signalizaciya-alligator-polnaya-instrukciya-po-ekspluatacii.html
https://PrideSaratov.ru/pro-signalizaciyu/avtosignalizaciya-alligator-instrukciya.html
https://AvtoKart.ru/pro-signalizaciyu/avtozapusk-alligator-instrukciya.html
https://autolocked.ru/avtosignalizacii/brelok-dlya-alligator
https://avtodigitals.ru/skhema-podklyucheniya-signalizacii-alligator/
https://AutoTuning.expert/avtosignalizatsiya/alligator-s-avtozapuskom.html
https://avtodigitals.ru/avtozapusk-alligator-kak-zavesti-s-brelka/

Why is the Alligator key fob not programmable?

The remote control for the Alligator alarm system broke down, and you decided to flash a new one. But I can't unlock the transmitter. Why can this happen with key fobs (TD 350, M2200, D 910, 975, S850RS, M 2200, S 875rs, S 200, M800, S400) and how to fix it?

Pager failure. Repair it yourself or replace it with a new one.
The “Ignition on” command is not detected by the control unit. Contact the specialists.
Jack mode was accidentally activated. Turn off and repeat the procedure for writing switches.
Damage to the control unit. Contact the service center.

Causes

How to find out the alarm model by key fob (starline, alligator, sheriff, tomahawk and others)

To fix the problem, it is important to understand why the Alligator car alarm does not respond to the key fob. There may be several reasons for this:

The power supply is discharged.
“Decoupling” the key fob from the security system.
Moisture leaking into the interior.
Damage to the antenna wire in the security system head unit.
Finding a car in an area of strong EM field.
Failure of the security alarm head unit.

In all the considered cases, a situation may arise when the alarm from the Alligator key fob does not go off and does not respond to the remote control at all

In such circumstances, it is important to know what to do to overcome the situation.

Instructions for use and setting up the Alligator key fob

The Alligator alarm key fob is a device designed to configure an anti-theft system. Using the remote control, the car owner can control basic functions, for example, remotely start the engine.

Instructions for using the key fob

How to set up autorun?

Download instructions for the Alligator alarm key fob

Video “Visual guide to setting up the system”

Comments and Reviews

Video

New cars > Car alarms >

Alligator anti-theft system with auto start: advantages and settings

Did you like the material? Share with your friends:

Have questions about car repairs? Ask them in the consultation section, to do this, click on the link below.

auto mechanic

If there is a key fob for the Alligator alarm system, it doesn’t matter whether it has feedback or not, then how can you determine the model of the security system based on its appearance? The instructions below discuss the answer to this question. Various models of alarms are listed, the total number of which exceeds 30. Most of these systems are not equipped with autostart, but there are also exceptions. The starting point is the appearance of the key fob, that is, the appearance of the remote control or pager. And the word “pager” here refers to a key fob with feedback. If we talk about the Alligator brand, it is known that pagers of this brand are always equipped with a display.

Types and models

All anti-theft systems from this manufacturer can be divided into two types according to technical characteristics:

with the option of remote autostart of the engine;
with feedback function.

There are several models of anti-theft systems with the option of automatic engine start and feedback:

From 500. This signaling is considered one of the most common and popular models. Thanks to the feedback option, the car owner can find out about the status of the protection at a distance from the car. The alarm range is about 2.5 kilometers, provided that the area is open. The anti-theft system is equipped with an immobilizer. In the event of an attempted theft, the IMMO blocks the operation of the starter device, making it impossible to drive the car. Crabbing code is used to prevent the possibility of signal interception. If necessary, the user can set a timer that remotely starts individual systems at a specified time. The average cost is 3100 rubles.
The S 325 model can be installed on any vehicle that has specific operation of electrical equipment. The package includes a remote control with a liquid crystal display, which displays the alarm status. There are icons on the screen that allow you to configure the alarm. Thanks to the display, the car owner can find out about the condition of the vehicle. The cost of the remote control on the market varies around 2800 rubles.
The S 875 RS model has a feedback option and is controlled using a remote control with buttons located on the sides. In open areas, the range of the signal is about two kilometers. The anti-theft system is equipped with an option to block the power unit if an unauthorized attempt to start the engine occurs. In this case, the alarm blocks the engine, which prevents movement by car. The package includes seven controllers that perform separate functions. The consumer can configure two sensitivity levels, so that the shock sensors will be triggered by physical impact on the car body. The system has extensive functionality, which has made it popular among consumers. The cost of the remote control varies around 3,300 rubles.
S 250. The anti-theft installation is controlled using three buttons located on the remote control. The package includes instructions and a keychain pager equipped with indicator lights. If necessary, the user can configure protection against false alarms of the siren. The main feature of this model is that the car owner can set up a call option from inside the car. The remote control has a vibration mode option; it can reproduce all signals without sounds. The cost of the keychain is about 3,100 rubles.
Another model from a popular manufacturer is L 530. The main feature is the presence of an Anti-HighJack mode and an additional channel. Using it, the consumer can program the functions of controlling optics, electric windows, and the trunk door. If you need to buy a remote control separately, the price of the device will be about 1200 rubles.
PS 302. The alarm is controlled at a distance of up to six hundred meters in open areas. And you can receive signals to the remote control from the system within a radius of 1800 meters from the car. Price - about 2000-2500 rubles.
Model C 300 is a full-fledged protective complex with the option of two-way communication and remote start of the power unit. The main feature of the signaling is the use of an improved communication channel with the Kilok code, which prevents pulse interception. There is a signal scanning and code grabbing function. The car alarm is controlled using a remote control equipped with a liquid crystal screen. The signaling range is up to 1.2 km. The internal combustion engine autostart function can be used in almost all modern cars equipped with diesel or gasoline internal combustion engines. The type of transmission and ignition system does not matter. It is possible to activate the motor start by a timer, at a set time or at a specific temperature. The car alarm monitors the operation of the internal combustion engine using the engine fluid pressure indicator or tachometer. The cost of a key fob with a liquid crystal screen is about 1,800 rubles.
TD 350. Anti-theft systems in this series have an auto-start and feedback option. According to many experts, this model is considered one of the best options in terms of combination of cost and quality. When developing the model, high-tech solutions were used, which ultimately resulted in high-quality signaling. The pulse transmission frequency from the control module to the remote control is 868 MHz. Thanks to the use of BACS Dialog encoding, the range is 3 kilometers. Modern technologies have made it possible to obtain a product that effectively protects a vehicle from hacking and signal interception. If necessary, the consumer can additionally connect a GSM unit, thanks to which the car owner can find out about the condition of his car. The presence of this unit allows you to monitor protection from anywhere in the world where there is cellular coverage. Data and status will be displayed in Russian, all information is displayed on the remote control screen. The range of the anti-theft system is three kilometers. The alarm system simultaneously controls seven or more independent security zones, it all depends on the type of connection and settings. The control key fob costs around 4 thousand rubles.
910. This alarm has two-way communication function. Thanks to the use of modern technologies, signal transmission is carried out over a secure channel, which eliminates the possibility of pulse interception. The user can put the car on protection with sound, without sound or with vibration. There is an Anti-HighJack option. When the engine is running, the machine can be automatically put into protection. Authorization of the vehicle owner is carried out at two levels. Great functionality allows you to choose one of several sound options for the siren. The price of the device is approximately 4,500 rubles.

Four buttons or more

Let’s immediately look at what key fobs with a display look like. In our instructions they are called pagers:

Each pager, as we see, is equipped with 4 buttons or 5. This is true even for the S-700RS model.

Remote controls with four buttons

Actually, there are not many four-button remote controls in the Alligator brand’s arsenal:

All of them are designed for two-way communication systems. The same remote controls are suitable for signaling devices of the SP family, although pagers differ for different models:

The same pager design is suitable for SP-30 and SP-40 systems;
The 75RS and 55RS alarms are equipped with a different pager that is not suitable for earlier models.

It’s a pity that such information is not written in the basic instructions.

How to find out if autorun is available

It is clear that only those systems that include a pager are equipped with two-way communication. We list them here:

S Family: 200, 250, 275, 300, 325, 400, 450, 475, 550, 575, 700RS, 725RS and 750RS, 800RS, 825RS, 850RS, 875RS, 975RS;
SP: 30, 40, 55RS, 75RS;
C: 200, 300, 500;
D: 810, 830, 910, 930, 950, 970, 975, 1100RSG;
TD: all models starting from 310;
M: any signal with a number greater than 1000.

Not all, but only some of the alarms that have been named are equipped with auto start. For example, in the “C” family, the 200th model does not have this option, but the rest do.

How can you immediately determine whether the signal system has auto start? There should be an icon on the display indicating that the engine is running. Most often this will be an image of smoke, and it is drawn from the bottom right. It turns out that you don’t even need instructions - everything looks so simple!

In conclusion, let's name one model that is an exception. We are talking about the LX-8000RS alarm system: you cannot equip it with a pager, but you can equip it with autostart. We provide a diagram as proof.

Remote controls without a display are suitable for the 8000RS signaling system. But its remote controls, unlike most “one-way” devices, have an increased range. This is stated by the manufacturer.

Instructions for using the key fob

In general, the connection algorithm looks like this:

The ignition in the car is turned off.
The Vallet service key is pressed. The car owner must know where it is installed. As a rule, the button is installed in a hidden place so that intruders do not gain access to it. The key must be pressed for 2-3 seconds, depending on the model. We recommend that you clarify this point in the instruction manual.
Then the button is released and pressed again, only the presses should be short-term and you need to click three times.
If everything is done correctly, the system will emit a beep, which indicates that the user must press all the remote control keys in turn. The process of synchronizing the device with the central unit will begin.
Then the ignition is turned off.

The procedure for setting up the remote control for older models that have feedback:

The ignition turns on.
The Valet service button is pressed three times.
The ignition is turned off.
Then the key is turned in the lock again, all the buttons on the remote control are pressed.
The ignition is turned off.

For anti-theft systems of the D, S or M line, the procedure for linking the key fob is as follows:

The anti-theft system is disabled.
The driver gets behind the wheel and installs the key in the ignition. If you are using a non-coded emergency system shutdown mode, then within 15 seconds after switching on you must press the service key three times.
The siren will emit one short signal, at this moment the diode indicator will blink. This indicates that the alarm is ready to program the remote control.
Then the button is pressed again. If we are talking about D line systems, then the car owner needs to hold down the key.
A long siren signal will sound, this indicates the successful completion of the programming procedure. You can also program other key fobs.
After completing the actions, the driver must wait 15 seconds, but during this time do not press anything on the remote control. The ignition is turned off.
There will be one long and one short sound of the siren. The programming procedure is completed at this point.

Nine budget security systems

Below is what Alligator alarm remotes look like, most of which are equipped with two buttons:

Two-button and three-button key fobs

You will notice that each device has an LED in its design. The three-button remotes are part of the M-300/400/500 family, as well as the latest model from the LX family. The "Open" and "Close" functions were separated, but the trunk control option remained.

According to the standard instructions, none of the listed systems are provided with feedback. That is, do not look for a key fob with a display for the LX-990, M-300 or M-500 signaling. We also note that the “out of the box” kit must contain two identical remote controls.

Advantages and disadvantages

Possibility of remote control of vehicle systems. Thanks to the feedback, the driver can quickly reconfigure some system functions without approaching the vehicle.
Monitoring the state of car protection. The presence of feedback allows you to determine in what mode the anti-theft installation operates and which zones are turned on when the siren is activated. If it is activated, a corresponding indicator will appear on the key fob display.
Possibility of remote engine start. Remote activation will allow you to warm up the interior in the winter. You won’t have to waste time starting the engine, which is especially valuable if the driver is late.
The devices are housed in a convenient compact housing.

In general, there are no disadvantages in the operation of the device. In some models, some functions may malfunction, but they can be quickly resolved by reconfiguring the remote control.

Benefits of the Alligator Protection System

Despite the fact that the company’s product range includes models with different technical equipment, they have similar features.

Let's call them:

The devices are powered from the vehicle's on-board network with a voltage of 12 V.
The current of all models is limited to 20 A.
A 1.5 V battery is used as a battery for the main key fob.
The Alligator car alarm uses a zone security system. If one of the sensors fails, the others continue to monitor their zones. The device continues to perform a protective function.
The key fobs are protected by a button lock that prevents accidental operation.
Built-in relay blocks protect the alarm from overloads and short circuits.
All models operate in the frequency range: 433 - 868 MHz.
The menu and information on the display are displayed in Russian.

I would especially like to note the ability of all models, without exception, to work in various regions of our country, including in the northern regions. Critical sub-zero temperatures will not become a hindrance in protecting cars.

Alligator car alarms use the latest industry developments. Let's talk about some of the technologies used in the production of models.

They distinguish the products from security systems of other companies:

Anti Hi-Jack function blocks the engine in case of theft;
the Comfort option makes the driver’s work easier: it makes adjustments to uncovered windows and sunroof;
some models in the line duplicate the immobilizer function, blocking an attacker from starting the engine;
models have the ability to turn on security when the power unit is running;
autostart can occur not only by simply pressing a button, but also by alarm clock, timer, interior temperature;
The latest generation models have a function that protects the turbodiesel from incorrect operating modes.

Let us also highlight separately the fact that the new Alligator “signals” work on the principle of interactive code encryption.

It works as follows. The main Alligator alarm key fob sends a request to the device to unlock the doors. The electronic alarm unit transmits back its requirement: a key is needed to carry out the request. Only after receiving it can the car doors be opened. Such interactive coding eliminates the possibility of electronic hacking: signal interception by scanners and grabber devices.

Download instructions for the Alligator alarm key fob

Manuals in Russian for key fob

Instructions for the Alligator C 500 key fob

Instructions for the Alligator S 875 RS key fob

Instructions for the Alligator C 300 key fob

Instructions for the Alligator S 325 key fob

Instructions for the Alligator S 250 key fob

Instructions for the Alligator L 530 key fob

Instructions for the Alligator TD 350 key fob

Instructions for the Alligator D 910 key fob

Tamper resistance

There is one online resource where they offer to purchase a manufactured code grabber - a device that cracks alarm codes. This device looks like a key fob, but it fits most Alligator systems. The code of one-way key fobs, as well as the code of various pagers, is emulated. The exception, supposedly, will be one of them: we are talking about a key fob with a “diode” display (S-250/275).

Screenshot of one harmless site

Any car alarm that uses the keeloq code can be hacked. Let us clarify that this statement also applies to models with a “diode” display. It would be strange if something new was used in the S-275 or S-250 - both systems are budget. Draw your own conclusion.

You can immediately find a resource offering other similar equipment. But all Alligator models will be listed there.

Another site with code grabbers

Anyone who knows how to use search will find confirmation. We wish you success.