Instructions for installation and operation of alarm models Alligator S series with auto start and two-way communication

Author: Victor

It is imperative that you read the instructions for using the Alligator alarm system with auto start before installing and configuring the system. The service documentation indicates all the nuances of adjusting the parameters of the remote start of the internal combustion engine.

[Hide]

How to setup

You can start the car not only from the key fob, but also autostart the Alligator alarm system based on temperature or timer.
Using this option allows the device to operate automatically when the specified parameters are met. Before setting up autostart on the Alligator alarm using the specified data, you must enter the programming mode using the key fob. To do this, do the following:

• Take the key fob and hold the service button F for two seconds.
• After the transition, the screen glows and a melodic signal from the key fob appears.

If you manage to start the engine, a running engine symbol is visible on the screen, and after 1.5 minutes the air conditioning/heating or other systems begin to operate.

By temperature

Setting up Alligator autostart based on temperature from the key fob requires several steps. The algorithm is like this:

Click on “*” and hold it for two seconds until a sound appears.

Release the key and click on the open lock symbol. Wait for the signal again.

Pay attention to the display. It should light up and a thermometer symbol will appear on the display.

The location depends on the signaling model.

• Click on “*” once and look at the temperature parameter at the top right.
• Click on the button and the key fob emits a short beep.

In this way, the Alligator is launched from the remote control. At the temperature set by the key fob, the system will have to start the engine. Note that to exit the mode you simply do not need to press any buttons.

By time

Now let's look at how to enable/program Alligator autostart from the key fob according to time. The action algorithm is as follows:

Press and hold "*" for two seconds. The key fob beeps and confirms entering the settings mode.

Click the button with the lock closed. A clock symbol appears on the screen, the turn signals flash once, and one beep sounds for the same amount of time.

Press “*” as many times as necessary to set the time. Each press produces a beep.

To exit programming mode, do not take any steps for 15 seconds.

Alligator security system models with auto start

Autostart is a function of remote control of the motor. Allows you to turn the engine on and off from a distance. The option is relevant in winter to warm up the engine. During the hot season, this function may also be useful if your car has air conditioning. By starting the engine in advance, you can sit in a cool cabin.

Let's consider 3 popular models with autostart function.

Model ALLIGATOR A-9

The model is equipped with a dual dialogue radio code DUPLEX DIALOG. This is an encryption protocol to protect data while being transmitted to the key fob. The radio code protects the system from hacking and provides full two-way communication.

The device has a high operating speed. In case of unauthorized hacking, the data will arrive on the communicator in 0.25 seconds. All information about alarms is stored in the module memory. There you can also find information about the state of the car alarm at one time or another.

ALLIGATOR C-3C

Improved version of previously released models. Suitable for any type of car. You can control the device via the Internet or using a mobile phone. To do this you need to connect the GSM module. It also allows you to track the location of the vehicle.

The radio channel is protected from hacking by a dynamic code. Range - 1200 meters.

ALLIGATOR C-5

Premium class device with liquid crystal key fob. For authorization, a narrow-frequency channel of 868 MHz is used. The range is from 2500 to 3000 meters, depending on the presence of interference. The frequency is twice the standard. This increases immunity to interference and ensures a continuous, clear signal.

The device is equipped with an immobilizer function. If an unauthorized start occurs, the device gives a signal and the electrical circuit is blocked.

Work options

The autorun function is used in several ways:

1. Activation by pressing a key on the remote control. The motor starts after pressing a certain button. Range depends on model.
2. Autostart based on temperature. Select the temperature at which the engine will start. Relevant in winter. The motor will be kept active and will not freeze.
3. Turning on the engine by timer. Set the time based on your work schedule. The engine will be warmed up when you leave, and you can drive right away.

Advantages

Autostart models have a number of advantages:

• Automatic engine start. Allows you to prepare transport for the trip in advance.
• Remote alarm setting Alligator. You can change autostart parameters without leaving home, without a service button in the car.
• Two-way communication. Models are equipped with sensors to monitor the vehicle's condition. Information is updated at a set frequency. The system monitors the level of protection. In case of unauthorized hacking, the corresponding information will be displayed on the key fob. An alarm will be triggered.
• Alarm effectiveness. Information about unauthorized entry is transmitted to the owner of the key fob. You will not confuse the alligator car alarm signal with another siren - it works exclusively for you.

Flaws

High productivity of the device requires high energy costs. Despite the low-power technology used during assembly, the batteries need to be changed at least once a month.

In addition, the keychain transmitter is sensitive to mechanical damage. To extend its service life, it is recommended to store it in a protective case.

How the engine autostart function works

Backup engine starting system
The autostart function can be used in any car, regardless of the type of engine (petrol, diesel) and type of gearbox (manual, automatic, variator).

There are two options for autostarting the engine:

• manually remotely,
• automatically.

In the first case, to automatically start, you just need to press the button on the key fob. You can also do this from your smartphone

It is important to remember that remote launch is limited to a distance of 300-350 meters

Automatic start is used when the machine is far enough away.

It can also be configured so that the system turns on without the driver’s participation at certain intervals, or according to the air temperature in the cabin. After receiving the signal, the starter starts. The car blinks the turn signals, and the key fob receives a notification about a successful start.

If the engine fails to start the first time, the system will make several more attempts, each time the starter will spin longer.

How to enable auto start on an Alligator alarm?

Alarm models with auto start have two key fobs: one with 5 buttons and a display, and the second is a simple 4-button. The main key fob has the option to enter the programming settings mode, as well as a two-way communication module.

Images are displayed on the display after commands are executed and are confirmed by sound signals or vibration.

The second key fob can only control the system in an already specified algorithm. You can start the engine remotely from both remote controls, but first you need to make all the settings.

The auto-alarm function allows you to set the setting mode by temperature value, by time, and control the start and end time of warming up. Alligator alarm autostart programming instructions:

1. To enter the setup mode, you need to press and hold the service button for two seconds (in some models this is the F button). The screen should light up and a melodic signal from the key fob will sound.
2. A running engine symbol will appear on the screen.
3. After starting the engine, two icons will appear on the display: an hourglass and smoke from the muffler.
4. After a minute and a half, all main devices will begin to operate: air conditioning, heating, etc.
5. When programming is complete, the key fob will emit a beep.

By time

• Press and hold the “snowflake” button for 2 seconds. The key fob will beep, confirming entry into the autorun settings.
• Press the “closed lock” button, a clock image will appear on the display, the turning lights will blink 1 time and the key fob will beep 1 time.
• To set the time value (after how many hours the autostart will occur), the “snowflake” button is pressed the appropriate number of times.
• Each press of this button will be accompanied by 1 turn signal and 1 pager sound.
• To exit the programming mode, simply do not press any buttons for 15 seconds.

Autostart based on temperature

• Press the “snowflake” button and hold it for 2 seconds until a sound signal appears.
• Release the button, press “open lock”, another signal will sound.
• The display lights up and a thermometer icon appears in the lower left corner.
• Press the “snowflake” once, in the upper right corner we will see the temperature value.
• Briefly press the same button again, the key fob will emit a short signal.
• At this temperature value the engine will start. If you do not press any buttons, the programming mode will be exited automatically.

How to disable auto start on an Alligator alarm?

The autostart function is very popular among car owners, but sometimes situations arise when it needs to be disabled. Some drivers believe that the autostart option reduces the vehicle's capabilities and impairs its protection against theft.

1. You must take and carefully study the instructions. There are various options for connecting autostart, but there are general principles for any model.
2. In some alarm systems, the function of disabling autostart is provided by the program. In this case, you need to set it to the off position.
3. If this function is not available, you can try setting the stop time to the same time as the engine start time (or one minute later).
4. If the alarm and auto start require the installation of an immobilizer, it is enough not to keep the key fob near the car. Try putting it in a metal box away from the car during autostart.
5. If these options do not help, you need to contact a specialist service center to reprogram the system.

Standard and extended set of options

How to program a key fob for an alligator alarm: setup and operating instructions

The number of security zones, each of which operates independently or is connected. It is recommended to install an Alligator car alarm with 4-6 independent control points. If an attacker turns off 1-2 security zones, this will not reduce the level of protection of the machine. Key fob functionality – budget models are equipped with an on/off button. In security systems that fall into the middle and high price ranges, the key fob is equipped with an LED screen that displays operating parameters. List of other options:

1. Emergency shutdown - in the event of an accident or disturbance in the stability of the electrical circuit, the alarm operates unstable. The presence of a service key on the key fob allows you to quickly render the system inoperative. The driver enters the PIN code previously recorded in the settings.
2. Range of action – it all depends on the chosen modification. The indicator ranges from 1 to 2.5 km.
3. Main frequency range – data transfer between the system and the key fob occurs in a certain range. The authorized sales center will tell you which frequency is least susceptible to hacking in the region.
4. Protection against forcible seizure (anti-hijack) - a special button on the key fob remotely blocks the power unit if an attacker is already inside the car.
5. Additional defense mechanisms - a criminal genius is constantly finding new ways to take over other people's cars. Developers representatives have an immobilizer option. If a criminal breaks into the cabin and tries to start the engine, the Alligator premium car alarm will block the power unit.

The functional alligator alarm system is equipped with a key fob that prevents accidental pressing of buttons. In the description, the manufacturer indicates that the locking option is included in the kit. Protection against electronic radiation used to hack a machine is provided by a digital or built-in relay. Information about its availability is available in the operating instructions. Branded alarm system for Alligator cars includes a number of other features:

• “comfort” – the ability to connect a sunroof closer, an electric window lift;
• “saving” – the key fob reduces battery consumption;
• “informing” – key fobs of premium modifications of the protective system display information about engine t;
• “ICE protection” – reduces the wear rate of the diesel engine;
• “timer” – turns on the engine in a given time period;
• “search” – the driver will quickly find the car that he left in a large parking lot;
• “Additional support” – a built-in additional power source reduces the likelihood of losing control of the alarm in the event of a low battery.

There is no limit for further perfection. The developed Alligator mid-range car alarm is equipped with additional outputs that are needed to connect new protective units.

On a note!

In the instructions, the manufacturer indicates that the system is equipped with the option of connecting at least 2 additional communication channels. If there is no such mark, then new protective blocks cannot be installed.

Equipment

Tomahawk 9010: autostart based on time, engine temperature

Items included in the delivery package Alligator S-825RS:

• service manual for installation, use and maintenance of the anti-theft system;
• main five-button remote control (with two-way communication), equipped with a screen;
• additional communicator without display (equipped with four keys);
• a set of wires, connectors, screws for installing an alarm system;
• anti-theft complex control unit (supplied in a black plastic case);
• shock and sensitivity sensor;
• siren;
• transceiver unit with wire and connection block;
• temperature controller for mounting on the engine and setting the autostart function;
• blue LED indicating the state of the security system;
• button to activate the service mode of system maintenance.

Photo gallery

Photo of alarm elements Alligator S-825RS:

Box Siren and communicators Set of wires

Download installation and operating instructions in PDF format

You can download manuals for installing and using Alligator security systems using the links presented in the table.

Advantages and disadvantages

Installing and adjusting the time on the Starline A91 key fob

Advantages:

1. Possibility of remote control of vehicle systems. Thanks to the feedback, the driver can quickly reconfigure some system functions without approaching the vehicle.
2. Monitoring the state of car protection. The presence of feedback allows you to determine in what mode the anti-theft installation operates and which zones are turned on when the siren is activated. If it is activated, a corresponding indicator will appear on the key fob display.
3. Possibility of remote engine start. Remote activation will allow you to warm up the interior in the winter. You won’t have to waste time starting the engine, which is especially valuable if the driver is late.
4. The devices are housed in a convenient compact housing.

In general, there are no disadvantages in the operation of the device. In some models, some functions may malfunction, but they can be quickly resolved by reconfiguring the remote control.

Loading …

Disabling the Alligator alarm

Before turning off the alarm in an emergency, you need to find out where the Valet service key is located. If the complex was installed independently, the car owner should know where the button is located.

Where is the service button?

Jack button behind the console

If the installation was carried out by specialists, you should look for the key in the following places:

• in the area of ​​the driver's pedals;
• in the place where the block with safety devices is installed, if it is located in the passenger compartment (the button is not installed in the engine compartment);
• in the free space behind the glove box;
• under the surface of the center console, behind the radio or ashtray;
• under the steering column, disguised in one of the bundles with standard wiring.

Service key behind the torpedo

Step-by-step instruction

For alarm models Alligator L430, L530, and L730, deactivation without a password is performed as follows:

1. Using the key, open the car door locks. Alarm sirens will sound.
2. Insert the key into the lock and turn it to the ACC position to turn on the ignition.
3. Press the service button within fifteen seconds after turning on the ignition.
4. Start the car engine.

If a password is used to disable it, the action algorithm will be as follows (suitable for M425 models):

1. Open the car door locks with the key.
2. Place the key in the lock and turn it to the ACC position.
3. Within fifteen seconds after this action, press the emergency button several times. The number of presses depends on the first digit of the password. If code 9 is used, the key is clicked nine times.
4. Wait a few seconds.
5. Turn the key in the lock to start the engine.

If the password was entered incorrectly three times during an emergency shutdown of the alarm, the anti-theft complex will be temporarily blocked.

Lexin spoke about the service disabling of car anti-theft systems.

For models M725, M700, M2000, S400 and others, service shutdown is performed as follows:

1. The door locks are opened with a key. The siren of the anti-theft complex will start playing alarm signals. The turn signals in the car will blink, as well as the interior lighting if this option is enabled.
2. Insert the key into the lock and turn it to activate the ignition.
3. Within fifteen seconds after the last manipulation, click on the Jack key. The alarms will be deactivated. The complex's LED indicator will stop blinking. The power unit of the car starts.

If the coded system deactivation mode is activated in the alarm, it is possible to use a personal password to control functions and disable them. Depending on the model, the procedure for assigning a code will be different. Any combination between 1 and 99 can be used as a password.

To disable the operation of the above alarm models using a password, follow these steps:

1. The car door locks are opened with a key.
2. The alarm will start working, alarm signals and lights will be activated.
3. The key is installed in the lock and moved to the ACC position. After turning on the ignition, it turns off immediately.
4. Within fifteen seconds after the last action, click on the service button several times, depending on the first digit of the code. If it is 8, then the key is pressed eight times. After entering the first digit, turn the ignition on and off again. If the password includes only one digit, then you do not need to re-activate and turn off the ignition.
5. Then, in fifteen seconds, you need to have time to enter the second digit of the password; the procedure is performed in the same way.
6. If the password was entered correctly, the alarm signals will stop playing, and the car lights and interior lights will not blink. The system LED indicator will stop flashing and the protective mode will be disabled. The driver can start the power unit.

Installation instructions

In accordance with the official manual, installation of all Alligator alarm components must be carried out with the on-board network de-energized.

If the “signaling” is mounted while the power is on, the system wires may short out, as well as failure of the electronic equipment. Malfunctions may appear in the operation of the battery.

Recommendations for placement and installation

Tips for installing elements:

1. The microprocessor device is mounted in the vehicle interior, for example, in the free space behind the control panel or car radio. The block is fixed using self-tapping screws or plastic clamps. Installation of a microprocessor module under the hood is not allowed, since this device is not sealed. Do not install the unit on other electronic devices to prevent interference.
2. The siren is placed under the hood of the car; the installation site must be protected from access from under the bottom of the car. Do not install devices near heating units and components. The siren horn rotates downward to prevent moisture from accumulating inside. A special bracket with bolts is used for fixation.
3. Limit switches are mounted on metal body components in a place where there is no accumulation of moisture or leakage. It is important that the switches are not accessible when the hood or trunk is locked. The device is fixed using a special bracket, which is included in the package.
4. The diode lamp is designed to determine the status of the alarm and is mounted on the center console. The installation location must be thought out so that the operation of the diode can be seen from the street, but the lighting source should not distract the driver while driving. To install the device, you will need to make a small hole in the dashboard. This must be done carefully so as not to damage other elements and devices.
5. The sensitivity controller is installed on the hard surface of the partition between the passenger compartment and the engine compartment. To fix the device, use two bolts, which are included in the package. You can install the controller under the instrument panel and use plastic ties to secure it. Regardless of the installation location, the sensor must be freely accessible from the passenger compartment.
6. The temperature controller is located on the cylinder block housing or other metal surface adjacent to the power unit.
7. The transceiver module with antenna is installed on the inner surface of the windshield or rear window. Installation must be carried out so that the device does not block the view. If the windshield has a shielding effect, as on many modern cars, then the antenna is installed at the rear. Double-sided tape is used to secure the device.

Connection diagrams

Photos of electrical circuits for connecting elements are given in this section.

Alligator 800 block connection card

Connection diagram for model 825 RS

Connecting System Wiring

When installing it yourself, it is important to correctly connect all components of the security system. Otherwise, the alarm may work intermittently.

Main 16-pin connector

Features of connecting contacts:

• black and white output is intended for connection to a car siren;
• black-brown contact is used to connect to the positive input of the brake pedal and the negative element of the parking lever;
• the red output is intended for connection to a 12-volt contact from the battery;
• the purple wire is used to connect to the positive inputs of the door trigger and the five-pin block of the electric drive;
• the black and yellow output is intended for connecting the status input of the autostart system, as well as the standard anti-theft installation of the car;
• the black-green contact is used to connect to the negative output of the hood trigger or to the temperature controller connection input;
• the dark green contact is for connecting the negative input of the luggage compartment trigger;
• the brown output is used to connect to the negative terminal of the door trigger or the negative contact element of the five-wire block;
• two white conductors are required for connection with pulse inputs to control the headlights;
• The yellow-violet contact is intended for connection to terminal 50/1 of the ignition switch, in particular to the starter lock control system;
• the black wire is the ground or ground of the car;
• white-red output is intended for connection to the battery;
• the dark blue contact is used to connect to the input of the second channel with programmable options;
• the white-violet output is intended for connection to the input of a tachometer or engine fluid pressure level controller;
• the yellow-green contact is an output for connecting to the additional blocking system;
• The gray input is intended for connection to the contact of the third alarm channel with programmable options.

Power 6-pin connector

Connection features of this block:

• the red contact is intended for connection to a high-current 12 volt input;
• the orange output is used to connect the power supply circuit of accessories;
• the white-pink contact is intended for connection to the power output of the second electrical circuit of the ignition system;
• the purple contact is necessary to connect to the input of the power system and block the starter mechanism;
• the red pin is also used to connect to the high current 12 volt output;
• The pink input is intended for connection to the power supply circuit of the primary ignition line or to the input from the switch.

User Anton Bobkov showed in detail the installation procedure, as well as connecting the connectors of the microprocessor module.

Connecting electric lock drives

If the vehicle uses a three-wire central locking system, then the connection of the elements will be as follows:

• black-blue and black-green contacts are not used;
• red-green and red-blue outputs are intended for connection to ground;
• the white-blue contact is necessary for connection with the standard car closure cable;
• The white-green output is used to connect with the standard electrical circuit for opening the machine.

If the car has a three-wire central locking system with positive polarity, the connection is made as follows:

• the black-blue and black-green contacts do not need to be touched, they are not used;
• red-green and red-blue outputs are intended for connection to a 12-volt electrical circuit with direct current;
• the white-blue contact is used to connect to the standard closing cable of the machine;
• The white-green output is intended for connection to the standard electrical circuit for opening the car.

In the case of a single-wire system, the connection will be slightly different:

• black-green and red-blue contacts are not used when performing a task;
• the red-green output is intended for connection to the car ground;
• the remaining cables are connected in accordance with the diagram.

In five- and four-wire systems with reverse polarity, there are no standard relays. Also, such cars may not have a central locking control unit. This is due to the fact that the 12-volt voltage is supplied directly from the ignition switch to the electrical drive devices. This provides a return output to grounding. One of the five contacts that come from the switch will always be closed to 12 volts; the position of the lock does not matter.

One or two more outputs must be connected to ground, regardless of the switch. Of the remaining two contacts, one should close to +12 volts when the lock is switched to Lock mode. The second output must be shorted to 12-volt power if the switch begins to operate in Unlock mode. In such vehicles, it is necessary to cut the standard electrical lines that come from the main switch. It is located in the driver's door.

Connecting the connectors

Features of connecting additional pads:

1. The black 5-pin connector is for connecting the antenna module. A wire of the appropriate color must be laid from the transceiver unit to the microprocessor alarm module. It connects to a 5 pin output.
2. The four-pin white input is used to connect an additional dual-zone controller. The connection is made in the same way - to the microprocessor module.
3. The white four-pin output is used to connect to a two-level sensitivity controller. On a microprocessor device, this connector is located next to the power 6-pin block.
4. The white 2-pin output is used to connect to the LED indicator.
5. The blue 2-pin connector is intended for connection to the Valet push-button switch.

Equipment

Any car alarm model includes two transmitter key fobs: a main one with five buttons with an LCD display and an additional simple 4-button one. The first one is designed to enter the programming setup mode in manual mode, and is equipped with a two-way communication module - command execution confirmation signals are displayed on its screen in the form of an indication of special characters and are accompanied by sound signals, melody or vibration. A simple transmitter with four buttons, which duplicate the functions of the main one with the exception of the service one, is intended only for controlling the system in a given algorithm.

Remote engine starting can be done from both transmitter key fobs; to do this, you need to press the buttons in a certain sequence. These combinations have their own variants for different types of alarms.

It is important to remember: starting the car and turning off the engine is always the same combination

If the start does not take place from the first command, the starter will be turned off automatically for a few seconds, followed by an attempt to start. The system will cancel the engine start only after the third time. The corresponding indication with the specified melody or vibration should appear on the display of the main key fob, the car siren will give one short signal, and the turn indicators will turn on twice.

Safety rules for remote or automatic engine starting:

• The car must be parked in an open space - starting in a garage or underground parking is not allowed;
• Always keep the parking handbrake on;
• On vehicles with a manual transmission, the gear indicator is fixed in the neutral position, and in an automatic transmission - in the “PARK” position;
• There must be sufficient fuel in the fuel tank;
• The auto start function must not be used when there is a passenger or animal in the cabin.

Advantages and disadvantages

Advantages of the Alligator S series car alarms:

1. Availability of feedback. Thanks to this function, the car owner can assess and establish the status of the security system without being near the car.
2. Great additional functionality. Auxiliary options will ensure maximum protection of the vehicle and its convenient use.
3. Automatic engine start function. Will provide the opportunity to start driving in an already warmed-up car.
4. Detailed setup and operation guide. With its help, even an inexperienced car enthusiast can independently set the necessary parameters for the alarm to work.
5. Easy to install. With the right approach, you can perform this operation yourself.

Disadvantages characteristic of these system models:

1. Unreliable key fob communicator. With prolonged use, the buttons on the pager begin to sink. The key fob may not transmit signals to the antenna adapter.
2. Low range. The radius of the key fob declared by the manufacturer is in fact much lower. In a city, this figure can be several hundred meters.

Page 29

ALLIGATOR S-8xxRS “User Manual”

Programming automatic engine start modes:

To select one of the listed automatic start modes, you must perform the following procedure. 1. Press and hold the button

within 2 s. The turn signals will turn on once. Keychain with 2-

third-party communication will give 1 signal, confirming entry into the programming mode.

2. To select the engine start setting mode by timer

— press the transmitter button (on

The transmitter LCD indicator will turn on

, the direction indicators will turn on once and the speaker

transmitter will give 1 signal); 3. To select the mode for setting the automatic engine start based on voltage (S- only

875RS) and/or temperature

— press the transmitter button (the LCD display of the transmitter will turn on

accordingly, the turn indicators will turn on once and the speaker will turn on

sensor will give 1 signal). Note (S-875RS only)

. The choice of automatic start type (by voltage and/or temperature) is determined by programmable function No. 1.15 of the system.

4. Press the button successively

transmitter to change the settings of the selected mode in the following

Timer start (values ​​correspond to time interval in hours)

Automatic trigger by temperature (also by temperature and voltage)

Autostart only by voltage (if this function is enabled, only in S-875RS)

Every button press

transmitter is confirmed by 1 flash of the vehicle's direction indicators and

1 transmitter beep with 2-way communication. 5. Repeat steps 2 - 4 as needed. 6. To exit the automatic engine start function selection mode, press and hold the button for 2 seconds

or do not perform any operations for 15 seconds. Turn indicators on

chat 2 times, the transmitter speaker will sound 2 beeps. 7. After exiting the mode for selecting automatic engine start functions, the transmitter display shows

2-way communication will remain enabled characters

, if the corresponding modes

automatic start are enabled (values ​​other than “OFF” are selected).

Modern Alligator security systems are complex electronic devices with two-way communication that provide a full range of anti-theft measures and the ability to control vehicle service functions from a distance. With their help, you can start the engine or turn off the car using the key fob, configure autostart at a given time and according to certain temperature indicators, while simultaneously monitoring the state of the security mode.

Model range and their main capabilities

The range of Taiwanese Aliigator car alarms includes the following security systems:

• S-800RS;
• S-825RS;
• S-850RS;
• S-875RS.

The S series alarm models have a remote engine start option, but its implementation is only possible on vehicles with a manual transmission.

ALLIGATOR S-800RS

This car alarm belongs to the category of business-class devices, has the function of remote automatic engine start and feedback. The system is equipped with a five-button communicator with an LCD screen and extensive functionality.

The 800 model has the following features:

• interactive signal encoding using the Keeloq encryption method;
• presence of the Anti-Highjack function - engine blocking mode when attempting to forcefully seize the car;
• the system is equipped with a FACT protection unit, designed to more effectively protect the machine;
• the presence of a Valet service mode, used to adjust operating parameters without a key fob;
• car alarm system with remote engine start is equipped with an additional output and has six independent security zones;
• there are three different power unit locks, and there are also 3 additional channels for connecting a communicator;
• using a two-level kick controller.

The system is designed to operate in an on-board network with a voltage of 12 volts. The alarm current consumption in security mode is no more than 15 mA. The main key fob is powered by 1.5 volt batteries, and the additional key fob is powered by 3V batteries. Data transmission is carried out over a channel with a frequency of 433.92 MHz.

Alarm equipment S-800RS

ALLIGATOR S-825RS

Description of the capabilities of the 825 model:

1. Starting the power unit of the machine by command or by air temperature. To implement the latter function, a temperature controller is used.
2. Availability of a user notification system. For this purpose, the main key fob is equipped with a display.
3. Warning the consumer about events that have occurred via a sound signal or vibration. To implement this function, the communicator is equipped with a speaker. Information about all events is displayed on the key fob screen.
4. Availability of Anti-Robbery function.
5. Protection of the security system from false alarms. A dynamic communication channel helps prevent interference and ensure reliable signal transmission.
6. Self-diagnosis of the security system. When you turn the protection mode on and off, the alarm independently checks the operation of all components and mechanisms, which allows you to promptly determine the malfunction. This will help with system maintenance.

The security complex has the option of checking temperature conditions. Remote diagnostics of the temperature level in the car interior, as well as in the engine compartment, will allow you to configure autostart in accordance with these parameters. This option can only be implemented if all sensors are correctly connected. You can also check the voltage level in the vehicle's on-board network.

The advantages include the presence of the Comfort option. With its help, the user can control door locks without using a communicator. It is possible to implement automatic window raising if electric lifts are installed.

The “Everything Affordable” channel provided a detailed review of this model of anti-theft systems.

ALLIGATOR S-850RS

The S-850RS model belongs to the Super category of devices and has a two-way data transmission channel. Information is sent using advanced dynamic BACS encoding. This ensures reliability of data transmission and its safety. To control the alarm, a communicator with a screen displays information about the operation of the system is used. The transmitter range is up to 2 km.

Standard alarm options:

• the presence of two communicators in the set; in addition to the main one, there is a spare one, not equipped with a screen;
• in the security complex control mode, the system’s range of action is up to 1 km;
• the presence of an option for sound or vibration warning of alarm activation;
• There is a clock, an alarm clock, and a countdown timer;
• The system allows you to start the engine remotely, by command from the key fob.

Keychain for controlling the S-850RS model

ALLIGATOR S-875RS

The range of the Model 875 in alert mode is up to 2000 meters, and when operating in signal transmission conditions - up to 1 km. The system is equipped with a communicator with a screen. When the alarm system is in operation, seven zones of the vehicle are protected, each of which is indicated on the communicator display with a corresponding icon.

Main features of the S-875RS security system:

• remote measurement of the temperature level in the car interior or under the hood;
• the presence of an energy saving mode in the communicator with feedback;
• built-in engine blocker;
• the presence of three external interlocks of the power unit;
• the consumer has the opportunity to additionally install a sensitivity and volume controller using the built-in output;
• automatic bypass of a non-working security zone when protection is activated;
• it is possible to implement remote automatic heating of the power unit at temperatures from -5 to -25 degrees Celsius.

The Carunlock channel showed how a code grabber can hack the anti-theft system of the Alligator model S-875RS.

Equipment

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline! Read more". Any car alarm model includes two transmitter key fobs: a main one with five buttons with an LCD display and an additional simple 4-button

The first one is designed to enter the programming setup mode in manual mode, and is equipped with a two-way communication module - command execution confirmation signals are displayed on its screen in the form of an indication of special characters and are accompanied by sound signals, melody or vibration. A simple transmitter with four buttons, which duplicate the functions of the main one with the exception of the service one, is intended only for controlling the system in a given algorithm

Any car alarm model includes two transmitter key fobs: a main one with five buttons with an LCD display and an additional simple 4-button one. The first one is designed to enter the programming setup mode in manual mode, and is equipped with a two-way communication module - command execution confirmation signals are displayed on its screen in the form of an indication of special characters and are accompanied by sound signals, melody or vibration. A simple transmitter with four buttons, which duplicate the functions of the main one with the exception of the service one, is intended only for controlling the system in a given algorithm.

Remote engine starting can be done from both transmitter key fobs; to do this, you need to press the buttons in a certain sequence. These combinations have their own variants for different types of alarms.

It is important to remember: starting the car and turning off the engine is always the same combination

If the start does not take place from the first command, the starter will be turned off automatically for a few seconds, followed by an attempt to start. The system will cancel the engine start only after the third time. The corresponding indication with the specified melody or vibration should appear on the display of the main key fob, the car siren will give one short signal, and the turn indicators will turn on twice.

Safety rules for remote or automatic engine starting:

• The car must be parked in an open space - starting in a garage or underground parking is not allowed;
• Always keep the parking handbrake on;
• On vehicles with a manual transmission, the gear indicator is fixed in the neutral position, and in an automatic transmission - in the “PARK” position;
• There must be sufficient fuel in the fuel tank;
• The auto start function must not be used when there is a passenger or animal in the cabin.

What is the price?

Approximate prices for the purchase of Alligator S series alarms are presented in the table.

Types of alarms

This anti-theft system comes in two types.

1. The system for starting the power unit. The varieties of models that have this function are characterized by automatic engine start settings, which are described in detail in the user manual. The car enthusiast has the opportunity to use standard settings, or create individual ones, taking into account the difficulties of operating the car.
2. Feedback system. These models are designed to provide full control of the vehicle when it is not in the driver's line of sight. Some models provide tracking functions via the GSM (satellite) system, which can be used to calculate the location of the car if it is stolen.

In order to find out the type of alligator anti-theft system, you need to carefully study the instructions, or look at the cryptograms glowing on the LCD screen of the key fob.

It is important to remember that some models combine feedback functions with the ability to autostart the power unit

Autorun errors

The main reasons for the failure of the automatic start system, in which the Alligator does not work, may be incorrect settings and technical malfunctions of the car engine:

• Automatic start by timer or temperature only works when the security mode is on;
• The engine runs at high speeds (silence occurs, restarts are cancelled);
• The oil pressure sensor and indicator do not work;
• The car is not set to the handbrake;
• There is no transmission "logical neutral" confirmation in automatic transmissions;
• There is no engine speed data (the tachometer does not work);
• The car doors or hood are open;
• In diesel units there is no confirmation of the readiness system of the pre-launch mechanism (warming up of the mechanisms);
• The specified time for the autorun program has expired.

For the correct operation of all settings, it is important to remember: if during a programmed start a command was given to stop the engine remotely, it will be turned off, but the device will repeat the start strictly according to the specified schedule. All program algorithms are saved when the security mode is disabled - the next time you arm it, autostart will work at the preset time until you reset the timers

During random engine shutdown, the system starts a new timing every 24 hours according to the factory settings.

Alligator S-825RS User Manual

Anti-HiJack Mode (AVRTM)

If the corresponding programmable function (function No. 1.10) is enabled, you can use the Anti-HiJack (AVRTM) mode (anti-robbery function). Enabling the Anti-HiJack (AVRTM) mode occurs as follows: - If you suspect the possibility of an attack or feel danger, you can activate the Anti-HiJack (AVRTM) function in advance by simultaneously pressing and holding the “Lock Closed” and “Lock Open” buttons » transmitter for 3 seconds with the ignition on. In this case, the siren will give 1 short confirmation signal and the system LED will flash and remain on for 5 seconds. — The transmitter speaker will emit 1 short beep and/or the built-in vibrator will turn on 1 time, and the “Gun” symbol will flash on the transmitter LCD display for 5 seconds. Once the AVRTM function has been activated, it will operate the first time the vehicle door is opened. If you are forced out of your vehicle, the Anti-HiJack (AVRTM) feature will work as soon as you open the door. Note: To protect yourself and your vehicle in a parking lot, activate the AVRTM function before leaving the vehicle. This will protect you even if your car keys and system transmitter key fob are taken from you after you have parked your car and armed the system. If you are attacked and your car keys and transmitter are taken away, the Anti-HiJack mode timer (AVRTM) will begin immediately after the system is disarmed and the ignition is turned on. It will no longer be possible to disable this mode using the system's transmitter keychain.

Anti-HiJack mode (AVRTM) activation: 1) After the ignition has been turned on for a total of 50 seconds after the Anti-HiJack function is turned on, the siren will turn on and short warning signals will sound for 7 seconds. The transmitter's speaker will sound alarms for 15 seconds and/or the built-in vibrator will turn on for 15 seconds. The turn signal symbols will flash on the transmitter's LCD display for 30 seconds. The Gun symbol will flash until the Anti-HiJack (AVR) mode is disabled. 2) After 7 seconds, the siren will start working continuously and the vehicle's direction indicators will flash. If the vehicle's ignition is turned off at this moment, the system will immediately turn on the engine blocking circuits. 3) Another 30 seconds after the siren turns on, the starter interlock circuits will turn on. The siren and turn signals will continue to operate and the engine will remain disabled until the vehicle's battery is completely discharged. Note: If the active and safe engine shutdown function is turned on in the Anti-HiJack mode (function No. 1.11) and the necessary connections are made, then in the 3rd stage of the Anti-HiJack mode the engine will be gradually forcibly turned off: within 30 seconds the vehicle's ignition circuit will periodically break for a split second, thereby causing the vehicle speed to decrease to a safe level, after which the ignition circuit and starter circuit of the vehicle will be blocked.

Benefits of the Alligator Protection System

Despite the fact that the company’s product range includes models with different technical equipment, they have similar features.

Let's call them:

1. The devices are powered from the vehicle's on-board network with a voltage of 12 V.
2. The current of all models is limited to 20 A.
3. A 1.5 V battery is used as a battery for the main key fob.
4. The Alligator car alarm uses a zone security system. If one of the sensors fails, the others continue to monitor their zones. The device continues to perform a protective function.
5. The key fobs are protected by a button lock that prevents accidental operation.
6. Built-in relay blocks protect the alarm from overloads and short circuits.
7. All models operate in the frequency range: 433 - 868 MHz.
8. The menu and information on the display are displayed in Russian.

I would especially like to note the ability of all models, without exception, to work in various regions of our country, including in the northern regions. Critical sub-zero temperatures will not become a hindrance in protecting cars.

Alligator car alarms use the latest industry developments. Let's talk about some of the technologies used in the production of models.

They distinguish the products from security systems of other companies:

• Anti Hi-Jack function blocks the engine in case of theft;
• the Comfort option makes the driver’s work easier: it makes adjustments to uncovered windows and sunroof;
• some models in the line duplicate the immobilizer function, blocking an attacker from starting the engine;
• models have the ability to turn on security when the power unit is running;
• autostart can occur not only by simply pressing a button, but also by alarm clock, timer, interior temperature;
• The latest generation models have a function that protects the turbodiesel from incorrect operating modes.

Let us also highlight separately the fact that the new Alligator “signals” work on the principle of interactive code encryption.

It works as follows. The main Alligator alarm key fob sends a request to the device to unlock the doors. The electronic alarm unit transmits back its requirement: a key is needed to carry out the request. Only after receiving it can the car doors be opened. Such interactive coding eliminates the possibility of electronic hacking: signal interception by scanners and grabber devices.

Tamper resistance

There is one online resource where they offer to purchase a manufactured code grabber - a device that cracks alarm codes. This device looks like a key fob, but it fits most Alligator systems. The code of one-way key fobs, as well as the code of various pagers, is emulated. The exception, supposedly, will be one of them: we are talking about a key fob with a “diode” display (S-250/275).

Screenshot of one harmless site

Any car alarm that uses the keeloq code can be hacked. Let us clarify that this statement also applies to models with a “diode” display. It would be strange if something new was used in the S-275 or S-250 - both systems are budget. Draw your own conclusion.

Another site with code grabbers

Anyone who knows how to use search will find confirmation. We wish you success.

Why do we need two-way communication?

The car security system also works when the engine is turned off. She must transmit event messages to a pager. This is feedback, that is, two-way communication. And when there is no pager, the essence of security comes down to the following:

1. When an alarm situation occurs, the siren, turn signals, etc. are turned on;
2. The shock sensor is designed for two levels of impact - with minor impacts, the warning level is triggered.

Systems with feedback are characterized by the same properties. In addition, they can transmit messages.

Most models belonging to the Alligator brand are “one-sided”:

1. N and NS families: models 105-605;
2. TD: 210, 212, 215;
3. L: 330-730;
4. M: 300, 400, 425 and so on, up to the 850 series;
5. LX: the whole series.

For a long time, the presence of a display was generally considered a tribute to fashion. And the owners installed only one-way systems. However, such systems are still being produced, and the demand for them has not decreased. That is, these products have their own market niche.

Single-sided key fobs in Premium version

Equipment setup

The installation is followed by step-by-step setup, because the Alligator alarm instructions from the key fob with four or two buttons contain the necessary tips. Insert the key into the ignition, press and hold the Valet button. After holding it for 3 seconds, the driver presses it 3 times until a sound signal appears. The final step is to quickly press each of the keys located on the remote control in turn. Further procedure:

• turn off the engine;
• disconnect both terminals from the battery;
• turn off the interior lighting safety element to reduce the likelihood of accelerated battery discharge;
• mount the system sensor near the controller using a 4-pin connector;
• turn on the “programming” mode of the alarm control unit;
• select the sensitivity level (from 0 to 10) - the average is 4-5.

Having chosen the sensitivity level, they slap the hood.

On a note!

The driver selects a value at which the car, on the one hand, does not react to vibration caused by a random passer-by, and, on the other hand, it will work if there is a break-in attempt. After installation is completed, fix the wires and control unit as indicated in the instructions.

Autorun errors

The main reasons for the failure of the automatic start system, in which the Alligator does not work, may be incorrect settings and technical malfunctions of the car engine:

• Automatic start by timer or temperature only works when the security mode is on;
• The engine runs at high speeds (silence occurs, restarts are cancelled);
• The oil pressure sensor and indicator do not work;
• The car is not set to the handbrake;
• There is no transmission "logical neutral" confirmation in automatic transmissions;
• There is no engine speed data (the tachometer does not work);
• The car doors or hood are open;
• In diesel units there is no confirmation of the readiness system of the pre-launch mechanism (warming up of the mechanisms);
• The specified time for the autorun program has expired.

For the correct operation of all settings, it is important to remember: if during a programmed start a command was given to stop the engine remotely, it will be turned off, but the device will repeat the start strictly according to the specified schedule. All program algorithms are saved when the security mode is disabled - the next time you arm it, autostart will work at the preset time until you reset the timers

During random engine shutdown, the system starts a new timing every 24 hours according to the factory settings.

• Absolutely legal (Article 12.2);
• Hides from photo and video recording;
• Suitable for all cars;
• Works through the cigarette lighter connector;
• Does not cause interference to radios and cell phones.

• https://vidsyst.ru/signalizaciya/avtosignalizaciya/proizvoditeli-avtosignalizaciya/alligator/nastrojka-avtozapuska.html
• https://autotuning.expert/avtosignalizatsiya/alligator-s-avtozapuskom.html
• https://alarmspec.ru/signalizacii/alligator/nastrojka-avtozapuska-alligator.html