How to register a new Starline a94 key fob?

The original Starline A94 2can key fob has an increased level of signal security thanks to the twage encryption system. It is worth noting that the level of cryptographic protection of the main control panel is the same as that of the additional one. The signal encryption method chosen by the manufacturer makes intelligent hacking by code grabbers unlikely. The A94 anti-theft system includes two key fobs. One of them serves as the main one, having a several times greater range and a liquid crystal display. The number of buttons on such a remote control is four. The second keychain plays the role of an additional one. Its range under ideal conditions is only 17 meters, there are three buttons, and no screen. But it is enough to activate and disable most security functions and some service ones.

The main key fob receives information about the alarm status if:

an alarm occurs due to sensor activation;
the system executes commands from any key fob;
the functions or operating modes of the complex have undergone changes in some way.

Information about the current state of the anti-theft system is regularly displayed on the screen of the main control panel. In case of any changes, the backlight and sound signals are automatically activated. It is possible to turn on vibration mode. About the Starline A94 car alarm.

In addition to general information about the safety of the car, the display of the main key fob allows you to find out what the temperature of the interior and engine is, the current time, the voltage level in the network and whether the alarm clock is turned on to start the engine. All data is transferred to it using the built-in GSM module. It is the main control panel that allows you to use the system’s capabilities at the maximum level, including the Slave service mode.

As for the additional keychain, it is intended to play an auxiliary role in case the main one is somehow unable to perform its functions. Its functionality is reduced not only due to a smaller range, but also due to the lack of a screen, which does not allow informing the car owner about the current status of the alarm and the car. It is adapted only to carry out basic commands.

How to unlock a91?

To unlock

alarm key fob, you need to simultaneously press the second and third buttons. A double beep will sound and the remote control will execute commands again.

Interesting materials:

How to set a photo to a contact in a Samsung phone? How to set a profile photo on Facebook without cropping from your phone? How to install Geolocation on a child's phone? How to install GIF on your phone screen? How to install Google Calendar on your cell phone? How to install a GPS navigator on your phone? How to set up speakerphone on your phone? How to install Google on the desktop on your phone? How to install Hi Suite on your phone? How to install a shortcut on your phone?

Equipment

Two system control panels are included as standard with the Starline A94. Both have a body made of durable, high-quality plastic. The main difference is that the main one is equipped with a screen. In addition, the manufacturer placed it in a leather case. As for the spare key fob, it is distinguished by both the lack of a display and a smaller number of buttons.

Both remote controls are internally equipped with microprocessors of the same model, which make controlling a modern security system easier and more intelligent. At the same time, their capabilities are more fully revealed in the main keychain.

System Features

This system can support up to 4 key fobs maximum.

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline! Read more"

It is very important to pay attention to the model of both the key fob and the alarm; in some cases, car owners do not pay attention to the additional indices following the model name. It will not be possible to flash a key fob of the same model, but with a different index; you will need to replace the alarm key fob. You should replace the key fob with the exact same one you have, without any indexes.

The car owner should know that programming a Starline key fob into the alarm unit will not cost only the firmware of an additional key fob; you need to immediately write down the key fobs that you are going to use. Thus, having one working key fob and one unstitched one, when programming it is necessary to bind the key fob (old and new) at the same time.

This point is very important, because Many car owners are faced with a problem when the additional key fob works, but the main key fob does not work.

Instructions for recording key fob codes into the alarm memory

Before programming the Starline key fob, you need to make sure that the markings on the new remote control of the installed security alarm correspond to the model designation on the old one. If the owner cannot independently determine the type of system, it is recommended to contact a specialized service.

When recording new Starline alarm remotes, you must re-enter the old ones into memory, since they are automatically deleted.

To record key fobs of Starline security systems, a service button is used, which is installed discreetly in the cabin. The programming procedure is different on some Starline alarm models.

Starline A4/A2/A1

Key fob codes are entered according to the following scheme:

Disable security.
When the ignition is inactive, press the service button seven times.
Connect the ignition. The system will inform you that it is ready for recording with a seven-fold light indication and a siren.
Press the K-I and K-II keys simultaneously. Hold them until the system gives a single short beep.
The remaining remote controls are registered using a similar method. Each recording is confirmed by sound alerts, with the number of signals corresponding to the number of the key fob in memory.
After recording the last remote control, turn off the ignition. If the system does not receive an information signal from the key fob within ten seconds, it exits the programming menu in automatic mode. The output is confirmed by the emergency lights operating five times.

Starline B6/B9

For the B6/B9 system, the procedure for recording remote controls is similar, with the exception of one point - the interval between entering key fobs into memory should not exceed five seconds. Alarms of the Starline B6 model can be equipped as an option with a digitally controlled radio relay; in this case, entry into the setting mode is indicated by a long sound signal (point 2).

Starline B6/B9 Dialog

Car alarm B6/B9 Dialog with the ability to control via a CAN bus has a memory for four key fobs. To record, you need to press the K-I and K-II buttons simultaneously.

Starline Twage С4/С6/C9

Alarms Starline Twage C4/C6/C9 are equipped with a stripped-down memory option that allows you to remember only two key fobs. Otherwise, the recording procedure is similar to the B9 system. The system does not have the ability to install a relay.

Starline A61/A91 and B61/B91

The A61/A91 and B61/B91 systems use a main key fob with three buttons and an additional key fob equipped with two keys:

After pressing the Valet button seven times, you need to activate the ignition circuit. This will be followed by a series of seven siren blasts.
Press buttons K-II, K-III and K-I, K-II on the secondary key fob. Hold until you receive confirmation, which will be a single signal from the siren and the built-in buzzer in the key fob.
Repeat the procedure for the remaining remote controls. A total of four key fobs can be flashed into memory. The time interval between recordings should not be more than five seconds.
Turn off the ignition, the car will give five flashes of the emergency lights or side lights, which indicates the end of programming.

Programming other models

This manual is suitable for models:

A62;
A63;
A64;
A92;
A93;
A94;
B62;
B64;
B92;
B94;
D64;
D94;
E60.

Programming looks like:

After pressing the Valet button seven times, you need to activate the ignition circuit. This will be followed by a series of seven siren beeps.
Press the K-I and K-II buttons on the key fob and hold until confirmation is received, which will be a single signal from the siren and the built-in buzzer.
Repeat the procedure for the remaining remote controls. The time interval between recordings should not be more than five seconds. The A94 system provides the user with an increased interval of up to 15 seconds between recording two remote controls. A total of four key fobs are prescribed.
Turn off the ignition, the car will flash three flashes with the emergency lights or side lights, which indicates the end of programming.

Starline with relay R2

For the E90 system, it is possible to use a code relay model R2, which must be re-flashed:

Enter the system setup mode and check the alarm blocking operation mode.
Check the selection of the appropriate relay operating mode (using the loop on the contacts).
Connect the relay power wire with black insulation to the vehicle body panels. The wire is marked GND (ground).
With the ignition off, press the Valet button seven times.
Turn on the ignition and receive confirmation signals from the siren (seven times).
After this, the owner has five seconds to connect the black relay power wire, marked +12 V, to the ignition circuit. If the relay is successfully written into memory, a long beep will sound. If the system includes a second relay, then it is stored in memory in the same way. Confirmation will be two long signals. A triple long signal indicates that the relay is already stored in the memory of the alarm control unit.
Turn off the ignition.
Disconnect power supply to the alarm control unit for 10 seconds.

Relays of type R2 can be installed in other Starline security systems, so when flashing the remote control you need to make sure whether the device is present or not. The procedure for programming relays into memory may vary.

To re-flash the code relay R2 into the memory of the A63/A94/D94 block:

Connect and disconnect the ignition seven times in a row.
After the last shutdown, press the service button seven times.
Immediately after the seventh press, turn on the ignition circuit.
Wait for the siren to sound seven times. After some time, the emergency lights will perform a triple test, and the melody on the key fob will turn on.
Turn off the ignition. The relay is registered and should function.

Photo gallery

Keychains A62 and similar models

Buttons on the main key fob and additional models A61/A91 and B61/B91

For models A6, A8, A9

Step-by-step procedure for reprogramming key fobs for the A6 system:

Connect the ignition circuits.
Press the setting key six times.
Wait for the siren to sound four times, which will confirm entry into recording mode.
Further actions depend on the type of key fob. A device with a display is registered by simultaneously pressing buttons 1 and 2. The keys are held until the siren sounds. To program an additional key fob (without a screen), you will need to press down buttons 3 and 4, which are held until the beep sounds. The number of beeps indicates the number of the key fob in the “signaling” memory. A total of four remote controls can be stored in memory.
Repeat the previous step for each keychain. The interval between storing data should not exceed six seconds. If the time is exceeded, the system exits the programming mode and gives a five-time hazard warning light.
Disconnect ignition circuits.

Main and auxiliary remote control of the A6/A8/A9 system
To program key fobs for the A8 or A9 alarm system, you need:

Press the service mode button with the ignition active. The key is held until the siren starts beeping. There are four beeps in total.
Remote control recording is done in a similar way to the A6 system.
If there is no signal from the remote control for five seconds, the recording mode will automatically exit with a five-time flash of the external light alarm.

For models V7, V62, V63

To program a key fob in the V7 security system intended for motorcycles, you must:

Connect and disconnect the ignition system circuits three times in a row. If the procedure is successful, the control LED will turn on for three seconds.
After turning off the diode, the owner has five seconds to begin an additional cycle of five connections and disconnections of the ignition. The ignition should remain on. The correctness of the procedure is confirmed by a five-time sound signal. After this, you can start recording key fobs.
The remote control should be registered by simultaneously pressing buttons 1 and 2. The success of the procedure is confirmed by a single siren beep.
Repeat the previous step for all remote controls. Each key fob number in memory corresponds to a similar number of siren beeps. A total of four communicators can be programmed.
Deactivate the ignition, after which the motorcycle will flash the emergency lights five times.

Key fobs of the V7/V62/V63 complex
For a dialogue type system V62 or V63, the firmware procedure is identical, except for a few nuances:

after recording the key fob into memory, a single beep is sounded by the siren and a single signal by the buzzer in the remote control;
when recording subsequent devices, the number of sound signals corresponds to the number of the remote control in memory;
after turning off the ignition and exiting the setting mode, a triple light indication appears;
When recording remote controls without a display, press the same buttons – K-I and K-II.

Description Starline A94

This model was released in 2013. The system is a reliable security complex, characterized by extensive functionality and the presence of an option for intelligent auto-start of the engine. The transmission of impulses between the control module and the key fob is carried out via an unscanned dialogue channel, which eliminates the possibility of interception. The Starline A94 anti-theft installation integrates a multi-system 2 channel bus. Thanks to the built-in GPS and GSM adapters, the car owner can track the coordinates of the location of his car.

Functions

What functions are implemented to ensure reliable security:

the consumer has the ability to control additional door locks;
you can configure the option to disable the standard system if the tailgate is opened;
if you install an additional blocker, you can set up a simulation of a power unit malfunction;
You can control the hood lock, only close it, without opening it.

What comfort options are available:

remote control of the pre-heater, if provided by the machine manufacturer;
option for automatic return of the steering column;
function of automatic adjustment of the driver's seat, if it is implemented by the car developer;
option to automatically activate low-beam headlights when the car starts moving, if the driver releases the parking brake lever or presses on the gas.

Options for automatic engine start:

the ability to turn off the audio system and windshield wiper blades when the function is activated;
option for simulating pulses of smart ignition locks;
the car owner can activate the option of heated windows or heated seats when the remote engine start is turned on;
option to simulate the second signal of the starter device;
If the machine is equipped with a Start/Stop button, and an error occurred when trying to autostart and the engine did not start, you can configure automatic reactivation.

What options can be configured when enabling protection mode if the machine supports the following features:

folding side mirrors;
automatic closing of the hatch;
When the security function is activated, you can configure the light path.

The autostudio channel provided a complete online review of all the options and features of the Starline A94 car alarm.

Description of configurations and characteristics

The complete set of systems for models A94 and A94S with a 2CAN module includes the following elements:

a control module or central unit in which a processor is located that transmits and receives signals;
one main remote control with two-way communication and a liquid crystal display and a second – an additional one, without a screen, a case for devices must be purchased separately;
button for mounting on the hood;
device for receiving and transmitting signals;
status monitoring diode lamp;
installation kit for connecting all components;
a service key designed to adjust and disable the machine “alarm”;
installation and operation manual;
service documentation for managing and adjusting the parameters of the GSM tracker, which describes step by step all the nuances of use;
consumer reminder;
motor blocking relay with block;
power unit temperature controller, with its help remote start is configured;
SIM card for installation in a GSM module.

Specifications

As for the main technical characteristics:

the control signal frequency ranges from 433.05 to 434.79 MHz;
number of radio channels for system control – 128;
the largest range of the main remote control is 800 meters when transmitting control commands to the unit, and if the key fob receives signals, the range can be up to 2 kilometers;
the auxiliary control panel will be able to operate within a range of 15 meters from the vehicle;
The tilt and shock controller is an integral type;
the operating temperature range at which the installation operates correctly is from -50 to +85 degrees;
DC supply voltage ranges from 9 to 18 Volts.

Safety precautions

When operating a car alarm, it is important to remember that disconnecting the battery when the protection mode is activated can lead to blocking the car’s engine. To start further, the power unit must be unlocked. If the “signaling” is connected independently, then when performing the task the battery must be disconnected in order to prevent possible voltage surges and failure of electrical equipment.

Starline A94 key fob diagram

The main key fob of the Starline A94 anti-theft system, as already noted, is equipped with four keys and an LCD screen. The latter is located on the front panel of the device, occupying it almost completely. Because of this, the buttons were placed on the side. The first is the main key, slightly highlighted because it is used most often.

Where is the service button on Starline A61

The display shows function icons in the form of icons and icons, as well as information about the current system status.

As for the additional remote control, it does not have a display, so all the buttons, of which there are three, are located in a circle on the main panel.

Transceiver with call button

The Starline company, as we see, in the fourth generation switched to using the same type of transceivers.

They may look different in appearance, but compatibility does not suffer from this. It is a pity that such principles were not relevant earlier. Then, there would be no problems with the choice of equipment.

Transceivers are also compatible

The transceiver is a small box with an antenna that is connected to the signaling unit. Without an “antenna,” of course, nothing works. The following Starline “antennas” are interchangeable:

A4, A2 and 24V (if there is no call button on the case);
A9, A6, A8, B9, B6;
C4, C9, C6;
B6 Dialog, B9 Dialog and here – A61, A91;
A62, A92, B62, B92;
All fourth generation (E90, E60, A64, ... D94).

Compatibility of old Starline key fobs

Currently, it is possible to record key fobs: - key fobs E60, B64, D64 are interchangeable (with each other) - key fobs E90, B94, D94 are interchangeable (with each other) - StarLine A2 to StarLine A4 and vice versa (one-sided and double-sided key fobs). StarLine A2, A4 and 24V (one-sided key fobs!) - StarLine B6 to StarLine B9 and vice versa (only one-sided key fobs!) - One-sided key fobs of old versions of series B (black LCD key fob and block) to new versions (blue LCD key fob and block) and vice versa. — StarLine B6 Dialog key fobs in StarLine A61 and vice versa, StarLine B9 Dialog in StarLine A91 and vice versa.

Attention. B6 Dialog and B9 Dialog have the main difference from B6 and B9 - these are Russified icons on the key fob, and the SN serial number looks like B91 W123456189 or B61 W123456189. If these signs do not apply to you, then replacing the B6 key fob with an A61 or B9 with an A91 key fob will not work.