How to register the Starline A91 key fob for an alarm system, programming the remote control

Car owners additionally install a car alarm. The Starline A91 signaling model is popular among car enthusiasts. Among the advantages of the system are a shock-resistant remote control, many functions, wide compatibility and programming of your own commands. In addition, the security alarm system with feedback locks the doors and turns off the engine ignition, which makes it much more difficult to steal a car.

Below is an overview of the key fob and system settings. Find out how to independently register car alarm commands, synchronize with the car, activate or reflash the device from the article.

Functions of the Starline A91 key fob

The device has a set of commands. A rubberized key fob (see photo) of the alarm with a small screen responds to attempts to enter the cabin without keys. The system also performs security functions.

Among the main alarm commands A91 are listed.

Security actions. The system turns off the ignition, locks the doors and hood lock. This prevents car theft and battery theft.
Automatic heating of the power plant. You can program the engine to turn on at the desired hours and bring it to operating temperature. Additionally, you can assign interior heating.
Setting up system options. The owner can prescribe the time for oil changes, scheduled repairs, etc. During operation, the screen will show how much is left until the required procedure.

4. Starline A9 set the time

The main Starline A9 key fob has a built-in clock (icon No. 6 on the display). How to set the time correctly:

Long press button 3 until 2 short beeps. The clock indicator on the display should start flashing.
First set the clock: button 1 – increase the value, button 2 – decrease it. If you hold down the key, the hours will change quickly.
Set the minutes - to switch from hours to minutes, press button 3. To increase and decrease the readings, also press buttons 1 and 2, respectively.

Alarm control methods

The multifunctional key fob system offers several options.

Button 1 activates the standard security mode. The car will squeak after mechanical impact.
The second button on the key fob removes the car from this mode.
If you press the first and second buttons sequentially, silent security will be activated. The car will not respond to the influence, but the owner will receive messages displayed on the key fob screen.
Double pressing the first button sets the car under security without sound, and double pressing the second button disarms it without a signal.
When you press the first and third keys of the key fob, the car is armed with the engine running.
The third button allows you to find out about the current state of the car and its settings: interior temperature. Double clicking will display additional information about the engine temperature on the key fob display. The auto search mode will be turned on.

Checking the key fob and searching for the service button

The very first step will be to check the key fob itself for its functionality. Inspect the key fob housing for cracks and chips, check the batteries. You can check the voltage on the key fob battery using a multimeter. If the key fob is new or the batteries have been changed recently, then you can skip this step.

The next step is to find out where the service button is located. Programming an alarm is not such a complicated process; you need to find a button from the alarm unit, usually it is connected to a wire. Most often, alarms are installed under the front panel of the car on the passenger or driver's side. You need to look under the front panel and find this button. If you cannot find the button, then you need to find the alarm unit and walk along the wires from it in search of the button.

How to register the Starline A91 key fob

Pairing a new system remote is easy. You can register the key fob for the Starline A91 alarm system to the car yourself.

Step-by-step instructions for connection.

Insert the ignition key. Turn it off, and then press the Valet key 7 times.
Now turn on the ignition. The alarm should make 7 sounds. After the siren has stopped speaking, the key fob binding mode is activated.
Simultaneously press buttons 2+3 and hold them. One system signal sounds. Let's release the keys.
If there are several remote controls connected to the alarm system, you must bind to each of them. We repeat the procedure (step three) for each device. The maximum number of key fobs that can be connected to one car is four. After each binding, one siren signal will sound.
Turn off the ignition. The parking lights flash five times in a row, which indicates that we were able to reprogram the car alarm system.

Indication on the key fob screen

The icons on the Starline A91 key fob are divided into several functional groups:

Animated icons on the image of the car are responsible for transmitting information about the status of the car. “Hood”, “door” and “trunk” indicate the activation of the corresponding limit switch, the key behind the windshield indicates that the ignition is turned on, and smoke at the exhaust pipe indicates that the engine is running. The “brake” indicator on cars with a manual transmission signals that the handbrake is pulled, on cars with an automatic transmission it indicates that the brake pedal is being pressed. “Hammer” indicates the shock sensor is triggered. Nearby there are icons with a lock (open or closed, respectively, indicating a disabled or enabled security status) and a speaker (crossed out – sound signals are disabled);
The bell and hourglass icons next to the digital clock indicate that the alarm and countdown timer are on;
The “Manual transmission” indicator lights up if the alarm system is configured to automatically start a car with a manual transmission. This is not a key fob setting, it is set during installation and cannot be disabled by the key fob or through the system settings menu;
the bottom row of icons is a cursor menu with which you can select the modes of periodic autostart, turbo timer, immobilizer, Valet, auto-arming;
the icon with a thermometer lights up when polling the vehicle’s condition simultaneously with the engine temperature being displayed in place of the digital clock;
“Satellite” appears on the screen if the M20-M21 beacon is connected to the system in slave mode (that is, it does not work autonomously, but as a GPS/GSM signaling interface);
The “PIN CODE” icon lights up if a secret code is specified in the settings, which is used when disarming the car without a key fob.

Programming Starline A91 key fob

Learning to use the alarm remote control is simple. Above we have given instructions for programming key fobs. However, the functionality of the system is broader. You can customize the alarm for yourself.

Button 1 on the key fob is responsible for the following system commands.

Activation of security mode (one press).
Silent security (two consecutive clicks).
Door locking when the engine is running (one touch).
Enable/disable shock sensor (double press).

Button 2.

Exit alarm mode (1 press)
Disabling silent security (2).
Additional shock sensor (2 presses).
Opening doors with the engine running (1).
Alarm interruption (1).
Anti-robbery mode (2).

Button 3.

Indicator of temperature degrees in the cabin (1).
Search mode (2).

A long press records additional system commands: auto start on an alarm clock, turbo timer, immobilizer and much more.

You can learn about the correct firmware of the key fob from the video.

Description of the Starline keychain

The car alarm package includes 2 Starline key fobs:

Basic. The main console is equipped with a display and feedback. With its help, any functions provided by the manufacturer can be programmed.
Additional remote control. This device does not have a display or a notification system (only buttons located vertically). For this reason, the functionality of this device is limited.

Identification of buttons

The presence of three keys on the key fob allows the car owner to customize the system to suit his requirements. Moreover, each key has its own designation.

The purpose of button number 1 provides for its use in the following cases:

A single short press activates the standard security mode. If you press again after 5 seconds, the system will begin to operate in silent mode.
A quick double click helps enable shock sensor monitoring.
Using this key you can close the car door when the ignition is on.

Button 2 is provided to perform several actions on the alarm:

A short touch on the button disables the standard mode. Clicking again (after 5 seconds) removes silent security.
By clicking this button once with the ignition on, you can open the locks on the car doors.
This key removes the alarm mode. This may be necessary if the alarm has gone off, but the car is safe.

Button 3. The third button of the Starline remote control is used in several cases:

When pressed briefly, the control mode is registered. In this case, diagnostics of systems and sensors will be carried out in forced mode.
Holding the key for a long time activates the previously set mode.

Display value

Indication is usually called all the icons and pictograms shown on the display of the main remote control.

There are several letter images:

A — activation of the anti-robbery mode;
B - use of additional channel 3;
C—panic mode setting;
D - search activation;
E — setting loud confirmation signals;
F—turn on/off silent security;
G - selection of quiet confirmation signals;
H — shock sensor control in remote mode;
I — activation of the “Jack” mode;
J — checking the temperature conditions and operation of the configured vehicle systems;
K — install additional channel 2;
L—opening the luggage compartment remotely.

There are several more symbols that provide information about the state of the anti-theft system.

Key fob functions

The main function of the system is to protect the car, however, the car key fob can be registered (“flashed”) to perform additional actions:

In the main Starline remote control, you can set the current time.
It is possible to set an alarm clock.
Optimal adjustment of the volume of alert signals is offered.
There is a countdown timer.
Installation of a system in which silent notification operates.
The manufacturer offers several types of sound signals.

All this makes using the Starline alarm system more convenient.

Why is the Starline A91 keychain not registered?

Sometimes owners have a problem that the remote control has become untied or the commands are not registered. You need to check the integrity of the battery. If the key fob indicator blinks, then the system commands may not reach the control unit. The battery needs to be replaced.

Or, if the number of key fobs in the system is already more than 4, then the previous alarm remotes begin to be deleted independently. Then you need to reprogram the device again, linking it to the car. If things don't work out, take it to a service center for reflashing.

In what cases is it necessary to reprogram the key fob?

Situations, in addition to losing the key fob, that force the owner to reflash the control panel can be:

damage to the key fob included in the delivery package;
the need to use additional remote controls within the organization or by family members;
purchasing a used car with an incomplete set of control panels;
regular failures of one of the standard key fobs, for example, the system is not set to autostart, which may be caused by a manufacturing defect.

How to reset settings on Starline A91 alarm system

It happens that the remote control is faulty. Then it’s worth going to a service center to update the firmware of the Starline key fob. First you need to reset the alarm settings. If the individual shutdown code was not programmed, then you need to perform the listed actions.

Open the doors with the key. The car's dimensions will flash 4 times.
Turn on the ignition. Get to the Valet button, press it three times.
Turn off the ignition. The siren should sound.
Now you can start the car and get to the officials to flash the Starline alarm key fob.

System Features

This system can support up to 4 key fobs maximum.

It is very important to pay attention to the model of both the key fob and the alarm; in some cases, car owners do not pay attention to the additional indices following the model name. It will not be possible to flash a key fob of the same model, but with a different index; you will need to replace the alarm key fob. You should replace the key fob with the exact same one you have, without any indexes.

The car owner should know that programming a Starline key fob into the alarm unit will not cost only the firmware of an additional key fob; you need to immediately write down the key fobs that you are going to use. Thus, having one working key fob and one unstitched one, when programming it is necessary to bind the key fob (old and new) at the same time.

This point is very important, because Many car owners are faced with a problem when the additional key fob works, but the main key fob does not work.

Ways to unlock Starline A91 key fob

If the remote control malfunctions, turn it off. You can use a custom code that you programmed earlier.

open the door with the key. The car will blink its turn signals 4 times;
turn the ignition key by pressing the Valet button the previously set number of times;
write the system startup code. The Starline remote control should vibrate slightly;
turn off the ignition. We receive confirmation from two flashes of turn signals;
The system is deactivated, you can go.

Errors

Not all car enthusiasts are able to carry out this simple work. This happens due to very specific mistakes that are repeated by almost every driver.

The most common mistake. This is a non-simultaneous pressing of buttons. To protect against unplanned reprogramming, the system is very sensitive to simultaneous button presses. Even a difference of 0.1 seconds between presses is considered non-simultaneous. Therefore, even experienced professionals who work with alarms do not manage to press the buttons correctly the first time. If you didn’t succeed the first time, then try again;
When registering several key fobs, people often forget about the 5 second rule, as a result of which the unit remembers only the last key fob. Be careful when operating;
If you bought the car secondhand, then the system security code may have been changed. If the block does not go into recording mode when you click on “valet”, you need to contact the former owner and clarify this issue.

Conclusion

. Every car enthusiast who has an alarm system in their car needs to know how to register and program the Starline a91 key fob. After all, this may be required in a variety of situations. The work is not difficult, but requires a certain skill. It is especially difficult to press the buttons in a timely manner the first time. There are also other nuances that also need to be taken into account.

Site forum https://autosiga.ru/

Starline A91: additional (spare) key fob

The alarm system has two remote controls - primary and secondary (see photo). The main key fob has a remote antenna, a color screen informing about the current state of the car, and three buttons on the side.

An additional or spare remote control differs from the main one and is necessary in case the first one is lost or the battery is dead. This key fob does not have a screen, and it cannot conduct a dialogue with its owner - a device without feedback. The remote control buttons are on the flat side, they retain all functions. A spare key fob can be used to open doors. The second remote control will help you unlock the interior or turn on the autostart of the engine.

Key lock

The key fob functions provide the ability to block accidental button presses (for example, when worn in a pocket). To do this, you need to simultaneously briefly press buttons 1 and 3. After this, the key fob will give one short signal, and the “KN BLOCK” icon will light up on its screen. The key fob will not respond to all subsequent button presses.

To unlock the StarLine A91 key fob, just press buttons 2 and 3 simultaneously. The key fob will emit sound and vibration signals, and the “KN BLOCK” icon will disappear.

Starline keychain prices

You can buy a standard remote control in any city in the country. The price of Starline A91 fluctuates between 1000-3000 rubles, depending on the distance of the seller or additional services.

Pros of alarm:

universal design - compatible with almost all cars with manual or automatic transmission;
complex encryption system;
increased range;
versatility and long warranty periods.

How many keychains can be attached

Each car owner can register a new key fob for Starline A93, but the number of such actions is limited. The maximum number of remote controls that can be connected is no more than four. If you write the fifth one, the first one will be deleted. In most cases, this amount is enough. If there are not enough devices, additional devices can be used.

How to configure and set the time on the Starline A91 alarm key fob

When linking the remote control to the car, you need to set the clock.
After replacing the battery, it is advisable to reset the time, because when it is removed, everything is reset. To carry out this procedure, you need to carry out the following steps: Press the three key fob button.

After a triple signal from the remote control, we set the clock by operating buttons 1 or 2. These two keys are responsible for increasing or decreasing, and the third selects the hours and minutes.

After correct installation, we stop pressing anything. The Starline alarm key fob will sound once and the current time will be recorded.

Setting the time

One of the functions of security system key fobs is to display the current time on the screen. This is not just an opportunity for the owner of such a device to find out the exact time at any time of the day, but also to remotely start the engine on a schedule. But sometimes there is a need to know how to reset the time. One of the reasons is replacing the device's battery. The degree of its discharge is indicated by a special symbol on the key fob screen. If the battery status indicator starts blinking, this is a sign that it is time to replace it. And when the battery is removed, the time is automatically reset. And now, if the time is not set correctly, the programmed capabilities of the system - starting the engine by an alarm clock, by a given interval or by a timer - will not work correctly. And this can lead to such troubles as:

By the time you are scheduled to leave the house, the engine will not be warmed up.
Increased loads on the starter when starting the engine in winter.
The battery may fail.

Setting the clock can be done in two ways:

According to the instructions. Time is customizable. Corrected by calling special commands from the menu;
Radical. Change the battery strictly at zero hours and zero minutes local time. As soon as the battery takes its place, the time on the key fob will reset to zero and the countdown will begin from that moment.

In order not to wait until midnight, programming is easier to do according to the instructions. You must press and hold button No. 3 in this position. After three signals from the remote control, you can set the time using service buttons No. 1 and No. 2 (see the figure above). These buttons increase or decrease the time digits, and button No. 3 allows you to move between hours and minutes.

Once the time is set correctly, you don't have to press anything. The system will automatically signal with a short signal that the key fob has been programmed.

Programming Sequence

To adjust functions and additional channels, a cursor-based setting is used, which allows you to select the required icon on the display and forcefully start the mode. Additional settings for the tables are carried out through the menu; entry is made by pressing the special Valet button 5 times.

A table of programmable security and service functions (AF) is given in the documentation; the driver selects sections and assigns the required parameters using buttons located on the remote control. To configure the automatic operation of the motor, a separate table of programmable start functions (SF) is used. Additionally, the functionality of the channels and the volume of the signals given by the car when receiving commands are adjusted.

Basic requirements for key fobs

It is clear that the new key fob must be compatible with the signaling unit installed in the car. It should also be possible to disarm the car. If there is at least one active key fob, just press the “2” (UNLOCK) key on it, and the security mode will turn off. The battery must be installed new, otherwise various troubles are possible. If all requirements are met, proceed to the recording.

All Starline alarm models can be divided into two main classes: “Dialogue” and “regular”. Starline Dialog is a new solution that uses only key fobs with feedback (main and additional). If we are talking about “Dialogue”, then when recording the main key fob, you need to press the “2-3” buttons. On the remaining key fobs press the combination “1-2”.

So, if you need to register a key fob for a “regular” signaling system (not “Dialogue”), then what combination is used? That's right, these will be buttons “1-2”.

Programming the CAN interface channel

To enter the programming mode of the complex, the block supplying power to the processor unit is turned off. Then the adjustment key is pressed and held, while the power circuits are connected. The siren will sound 5 beeps, after which you must release the key. The transition to the CAN parameter settings menu occurs automatically (confirmed by 4 signals). The selection of the subsection and car model is performed using the adjustment button (Valet), the standard key fob is not used during setup.

Setting up the key fob after replacing the battery

Unfortunately, all settings, from the time on the display to the start of the motor, will have to be configured again each time. Serious settings get lost and do not work correctly. Therefore, it is better to remember or save information on connecting the options you need.

No response to key fob

First of all, you need to make sure that the battery is working and the display is working at its full contrast and brightness; if this is the case, then the following problems are possible:

The distance from the key fob to the car exceeds the range. It is worth paying attention to nearby possible interference and taking into account the reduced range in parking lots.
Check the system's response to the spare key fob. Which will make it clear that the problem is in the starline system or in the main key fob.

If the problem is with the key fob, you should reprogram it as indicated at the beginning of the article. The system memory is not infinite, which means it is possible that the system “forgot” the key fob. But if this option does not solve the problem, you should contact the appropriate service.

If you don’t want to contact the center, then if you have the skills and the necessary tools, you can re-solder it yourself, but working with the software is only possible in the service center, because There is no publicly available data on this issue.