Replacing the cabin filter Lada X-Ray: instructions, installation, testing

Many car enthusiasts neglect replacing the car's cabin filter, considering this procedure unnecessary.

But if you take a closer look, the filter was created primarily to prevent dust from the street from getting into your lungs.

In addition, if you do not change the filter, it begins to clog, which slows down the air flow and creates additional resistance for the stove fan. Quite often this is why it gets cold in the car in winter.

In this article we will look at a process such as replacing the cabin filter in a Lada XRay car . The manufacturer recommends replacing the cabin filter every 30,000 kilometers, or once a year. In reality, everything depends on the operating conditions of the car.

If you often drive through villages, on dusty roads or in conditions of increased smoke, then it is recommended to reduce the replacement time by at least half - after all, your health depends on it, and this is the most important thing. So, in order to replace the cabin filter of the Lada X-Ray, you will need a TORX T20 key and no more than 30 minutes of time.

Position the vehicle so that the right front door opens freely and perform the following steps:

Remove the trim trim at the bottom left of the glove compartment using a TORX T wrench. Remove the filter cover by pressing the latches.

Carefully remove the filter without spilling accumulated dust into the interior of the air ducts.

To install a new filter, squeeze it with your hand and push it into the hole - it will straighten out inside.

Reinstall the cabin filter cover. Screw the decorative panel into place.

If for some reason access to the cabin filter is difficult, you can remove the glove compartment lid. To do this, remove the right trim (near the door) and, opening the glove compartment, unscrew three bolts (two on top and one on the left). Then disconnect the light bulb and remove the cover - this will free up a lot of space and make access to the cabin filter easier.

(1 ratings) Loading…

Replacing the cabin filter on Lada XRAY: 1.6, 1.8, video

Replacing the cabin filter on a Lada X-Ray is a planned procedure. It’s easy to do it on your own, just follow the instructions. Many work immediately according to a video or regular instructions, some drivers go to a service station, watch how the work is done, and then carry out the necessary operations themselves. It is not necessary to remove the glove compartment, but it will make maintenance easier.

Why and when do you need to change the cabin filter?

The need for a salon attendant is clear even to a schoolchild. The quality of air purification, elimination of microbes and unpleasant odors largely depends on the type of filter. The highest quality option is coal, but others are also suitable for solving current problems.

Important! Regularly changing filters is the key to a healthy atmosphere inside the car.

The average time to replace a cabin cleaner is 15 thousand km, that is, the old element is removed and a new one is installed every service. The failure of the filter can be judged by the deterioration in the quality of air masses and the appearance of foreign odors.

The more often the cabin filter is replaced, the cleaner the air will be, and the longer the heater and air conditioner will last.

In the video on replacing the cabin filter of the Lada X-Ray, they usually say that the service interval is 15 thousand mileage. But these are average data - if the quality of the roads is poor, other operating conditions are unfavorable, the filtration element will sooner cease to perform its main functions. In this case, the service time is halved.

Important! Professionals recommend replacing the old element with a new one at least twice a year. When servicing your car in the spring, it would be better to install a carbon element - it copes with unpleasant odors and allergens.

In summer, when there is increased dust, pollution occurs much faster. Frequent exposure to traffic jams is harmful to the filter. In autumn, leaves and twigs often get into the air ducts. You should be alert to such symptoms as a drop in the power of the ventilation system, an increase in the level of air humidity in the cabin, and noise when the fan is turned on at maximum speed.

How to choose the right filter

To replace the cabin filter of Lada X-Ray 1 8, you need to choose the right new element. The original is the best solution, but it is expensive. When selecting an analogue, you must follow the manufacturer’s recommendations. Dimensions requirements:

• 216 mm length;
• 200 mm width;
• 35 mm height.

Deviations of a few millimeters are acceptable, there is nothing to worry about.

The manufacturer's recommended article number is 272773016R (dust model) or 272773151R (charcoal type). Sometimes the article numbers at dealerships are different; this point can be clarified with the manager.

Important! Carbon filters are better than dust filters, but they are also more expensive. The accordion in such models purifies the air better.

GodWill, Corteco - the optimal alternative to original elements. You can also choose other manufacturers.

Compliance with dimensions is very important

Where is the cabin filter located?

To replace the filter in the cabin of the Lada X Ray 1 6, you must first remove the old element. It is located under the instrument panel. It is advisable to remove the glove compartment, although some craftsmen carry out work without touching it. There are usually no difficulties with performing the procedure.

At a service station, the replacement procedure costs from 700 rubles, you can do everything yourself in literally 20 minutes

Replacing the cabin filter on Lada Xray

When replacing an old filter with a new one, you can follow the manufacturer's recommendations or the following simple instructions. To make the procedure easier, it would be better to move the front passenger seat all the way back. The plug is located immediately behind the center console and is accessible. You need to squeeze the tabs with a little force and the plugs will move forward. The cover must be pulled towards you.

Further:

1. Pull the filtration element from below until it disengages at the top. The filter is larger and the hole is smaller. It is advisable to work according to the accordion scheme.
2. Clean the installation cavity from dirt. It is optimal to use a vacuum cleaner with a narrow, comfortable attachment, but other options are also suitable. For example, high-power airflow will clean the cavity, but will require cleaning the interior.

3. Attach the new filter element to the cavity in the reverse order. First you need to insert the entire top of the filtration element, then push through the lower part.

4. Place the cover in place until you hear a characteristic click. The latches may break in the area of ​​the plug. In this case, you can mount it using a pair of self-tapping screws; there are already working holes there.

When installing, you need to look at the arrows that are located on one side of the filter. They indicate the direction of movement of air masses. As the filtration element is removed, debris falls onto the mat. You will need to vacuum the interior and the stove body.

On cars with pre-installed air conditioners, filter replacement is usually combined with cleaning. There are many aerosols on sale for treating (including disinfecting) honeycombs.

You will need to insert a flexible nozzle into the filter mounting holes. The working composition will first distribute itself evenly over the surface of the radiator, and then begin to flow into the drain.

It is enough to wait 10-15 minutes and secure the new filtration element.

Conclusion

Replacing the cabin filter on a Lada X-Ray is a mandatory regular procedure. The old element is sometimes cleaned, but this does not give the desired results. The work is simple, they are usually done independently. The element is located under the glove compartment.

At a service station, the procedure is paid; doing it yourself is much more profitable. Filtration elements are installed with dust or carbon; the second option is more expensive, but is more preferable.

If possible, element replacement is combined with antibacterial treatment of the system (a special composition is required).

Stages of replacing the filter element Lada X-Ray

Compared to most other cars, replacing the cabin filter in the Lada X-Ray is relatively simple. Relatively, because the filter is not located in the most convenient place for replacement. Simple - because no special preparation is required for this operation. All you need is the new filter element itself.

It is pointless to dispute the benefits of salon tea, especially when it comes to coal ones. Therefore, it is not surprising that self-installation of filters on cars has become common. This is a routine and fairly simple procedure for periodic maintenance, there is nothing complicated about it

According to the regulations, replacement of the cabin filter is provided every 15,000 km, that is, every scheduled maintenance. However, depending on the operating conditions of the vehicle, the replacement period can be reduced to 8-10 t.km. mileage The more often you change the filter in the cabin, the cleaner the air will be and the better the air conditioner or heater will work.

Where is

Like most other cars, the cabin filter of the Lada X-Ray is located in the passenger compartment on the passenger side. The filter housing is located under the dashboard, so getting it out requires a little fiddling. At a car service center they will charge you about 700 rubles for a replacement, which is quite a lot for a 15-minute procedure.

The cabin filter makes the ride comfortable, so if a plug is installed, it is recommended to remove it and install a cleaning element. Much less dust will accumulate in the cabin. If you use carbon filtration, the air quality inside the car will become even noticeably better.

Removing and installing a new filter element

First, you need to make a reservation that you can use the official instructions for replacement by removing the glove compartment. But this makes no sense other than wasting time. This method is less convenient, but very fast.

Replacing the cabin filter of the Lada X-Ray is a routine and fairly simple periodic maintenance procedure. There is nothing complicated about it, so replacing it yourself is quite simple. To make the operation easier, you can move the front passenger seat all the way back.

The filter plug can be seen behind the center console when viewed from the glove compartment, and to remove the filter it is enough to:

We get to the installation site (Fig. 1).

Fig.1 Installation location Access to the filter plug is open. To remove it, you need to squeeze the protrusions shown in the photo. The effort required for this is small, they give in easily. After this, simply pull the lid towards you (Fig. 2).

Fig.2 Squeezing the protrusions Pull the filter by the lower part, moving upward, so that the upper part of the filter disengages. The filter element itself is larger than the hole where it should be inserted. Therefore, it is pulled out according to the accordion principle (Fig. 3).

Replacing the cabin filter Lada Xray

AVTOVAZ strongly recommends replacing the cabin air filter on the LADA XRAY every 30,000 km or once a year, whichever comes first.

During long-term operation of the Lada Xray in difficult conditions (heavy gas pollution, dust, etc.), the cabin air filter should be replaced 2-3 times more often.

We also recommend that you read

Like on the Lada Vesta, in the Lada XRAY the cabin filter is located in the housing of the heating, air conditioning and ventilation unit , the design of which we told you about earlier. To gain access to it, you do not need to remove the frill (wind cover), as on other Lada cars. Just follow the instructions:

1. Remove the tunnel lining on the front passenger side by removing the screws;
2. Remove the glove compartment lid (if necessary).
3. Look under the panel. Remove the cabin filter cover (No. 2) by squeezing the clips (No. 3).

In order to remove the air filter element from the heater body, pull it down by its lower edge (the hole in the body is smaller than the size of the filter). Then you need to clean the seat from dust and debris.

We also recommend that you read

Installation of the Lada Xray cabin filter is carried out in the reverse order, observing the markings indicating the direction of the air.

• The process of replacing the cabin air filter on the Xray is identical to the process on the Lada Vesta and is shown in the video:
• Source: lada.online

In what cases is it necessary to replace the purifier?

• Obvious mechanical damage to the housing, purifier;
• Getting water, moisture, sand, dirt into the structure, which creates a threat of debris being sucked into the engine cylinders;
• The element is filled with motor or transmission oil, antifreeze, brake fluid;
• The purifier is heavily contaminated; blowing with a stream of compressed air will be ineffective.

Replacing the cabin filter on Lada Vesta and XRAY

January 11, 2016 Lada.Online 56,095

The manufacturer recommends changing the cabin air filter on Vesta and XRAY every 15,000 km or once a year, whichever comes first. When operating a car in harsh conditions (heavy gas pollution, dust, etc.), the cabin filter should be replaced 2-3 times more often.

On Vesta and XRAY, the cabin filter (catalog number 272773016R) is located in the housing of the heating, air conditioning and ventilation unit. To gain access to it, you do not need to remove the frill (wind cover), as on other Lada cars.

Instructions for Lada Vesta

Procedure

:

1. (optional) remove the glove compartment cover (you don’t have to remove it if you feel the tunnel lining clamps (from step 2) with your hand, putting your hand behind the shield on the engine side);
2. Remove the tunnel lining on the front passenger side by unscrewing the screw and unclipping the fasteners at the top.

Look under the panel. Remove the cabin filter cover (No. 2) by squeezing the clips (No. 3).

To remove the filter element from the heater housing, pull it down by its lower edge (the hole in the housing is smaller than the dimensions of the cabin filter). Clean the seat from dust and debris (for example, dried leaves). Installing the cabin filter is carried out in the reverse order, observing the markings indicating the direction of the air.

The replacement process is also shown in the video:

Instructions for Lada XRAY

There is no need to remove the tunnel lining and the glove compartment lid.

Procedure

:

1. Remove cover 2, Figure 11-1, of the filter element by squeezing the latches 3 and pulling them.
2. Grasp the lower edge of the filter element 2, Figure 11-2, pull it and, with a slight downward movement, remove the filter element from the housing 1 of the heating, air conditioning and ventilation system unit.

The more convenient location of the filter makes replacing it faster and easier than before. Let us remind you that in order to extend the service life of this filter, it is recommended to install a mesh filter on the air intake.

Keywords: Lada Vesta filters | stove Lada Vesta | air conditioner Lada Vesta | air ducts Lada Vesta | lada xray filters | Lada Xray stove | air conditioner lada xray | air ducts lada xray

Review of Manufacturer Prices

*prices are as of January 30, 2019.

Recommendations for selection

Service center specialists strongly advise purchasing consumables with original factory catalog numbers. However, the high price of the “original” is not affordable for every car enthusiast. Therefore, they are forced to look for cheap but high-quality analogues.

Always check the integrity of the packaging, the presence of protective holograms, and quality certificates. If anything is in doubt, it is better to refuse the purchase.

Lada XRAY - Replacing the cabin filter

LADA XRAY 1.6 (2016): Replacing the cabin filter More details

Replacing the cabin filter on a Lada Xray car More details

LADA XRAY 1.6 (2016): Replacing the air filter More details

XRAY Cross The cabin filter is the cause of fogging of the windows. Replacement More details

Lada XRay - replacing the cabin filter More details

Lada XraY problems when changing engine oil Read more

LADA XRAY — Mesh filter More details

Lada XRAY: do-it-yourself maintenance Read more

you can replace the cabin filter (without removing the glove compartment) in 2 minutes Read more

Replacing the cabin filter of Lada Vesta is a SIMPLE and FAST way! More details

LADA VESTA HOW TO CHANGE THE CABIN FILTER. More details

Vesta - replacing the cabin filter. Improvement that makes life easier Read more

Consumables for TO-0 Lada XRAY More details

Lada Vesta. Quick replacement of the cabin filter. Regular or Charcoal? More details

Replacing the air filter on a Lada Xray car More details

Lada XRAY: replacement of all lamps Read more

How to replace or clean the Lada Xray heater motor More details

Changing the oil in the Lada Xray internal combustion engine Read more

15 COOLEST PRODUCTS FOR LADA XRAY FROM ALIEXPRESS AUTOMOTIVE PRODUCTS FOR VAZ VAZ ZHIGULI Read more

What air filter should I install?

Replacement intervals

every 20 thousand km.

For LADA (BA3) X-RAY (1.6 16V), FILTRON recommends the following air filters: AP 135/7. You can see the detailed characteristics of these filters in our catalog. The air filter completely cleans the air that enters the engine; this is a very important function in any car, including the LADA (BA3) X-RAY (1.6 16V)

The air that passes through the filter goes straight into the combustion chamber, so it is very important that it is clean. FILTRON AP 135/7 filters allow you to purify the air by more than 99%

Since the air that passes through the filter can be hot, and dust particles can be hot, air filters have fire-fighting properties, so we think that you have no questions left about which air filter to install in the LADA (BA3) X-RAY (1.6 16V).

Replacing the LADA XRAY cabin filter in St. Petersburg

Many motorists neglect the rule of replacing the air filter (hereinafter referred to as the air filter) in a timely manner, as a result of which fuel consumption increases and power decreases.

AvtoVAZ engineers recommend replacing the cleaning element (hereinafter referred to as the Element) every 45,000 km - every third service. If the owner drives less than the specified mileage, then two years from the date of installation of the purifier are considered as an alternative.

The process of replacing an element yourself is not at all difficult, but it requires care on the part of the repairman. Violation of the regulations is unacceptable. If difficulties arise during preventive maintenance, seek help from service station specialists.

Air filter for Lada X-Ray: price, articles, originals, analogues

Characteristics of the air filter for Lada X-Ray:

The shock absorbers on the car squeak, what should I do?

• Area 0.865m²;
• Weight 210 grams;
• Dimensions: 286 x 151 x 34 mm;
• Filling: paper with hygroscopic fiber. Carbon impregnation is optional, depending on the modification and characteristics of the cleaner.

Prices

Maintenance of LADA XRAY

Diagnostics LADA XRAY

Body repair LADA XRAY

Signs of a clogged cleaning element

• Unstable operation of the power unit at idle speed;
• Difficulty starting the engine;
• Power reduction;
• Passive acceleration dynamics;
• The accelerator pedal is uninformative;
• Increased fuel consumption;
• Shooting in the exhaust pipe as an indirect sign of enrichment or leanness of the combustible mixture.

The list is not exhaustive; other features may be added. If detected, contact a service station to conduct a comprehensive diagnosis of the technical device using digital equipment.

Independent non-professional intervention in repairs does not guarantee full functionality of the mechanism.

Cabin filter Lada X-RAY

The Lada X-RAY cabin filter can be regular or carbon. The Lada X-RAY cabin filter is an additional vehicle equipment. Production quality is of paramount importance. Lada X-RAY cabin filters come in case and cartridge designs. Single-section and two-section (installed in pairs side by side). Available for vehicles with automatic air conditioning.

They are usually rectangular in shape with a corrugated or plate-shaped insert in the middle. The cabin filter is usually located either in the glove compartment area or in the engine compartment. The Lada XRAY cabin filter is part of the car's forced ventilation system.

Air filter selection

Most car owners try to purchase original spare parts when replacing. But not everyone has the opportunity to get them for various reasons, for example, there are no official sales points nearby, or lack of funds to purchase an original part. Therefore, such drivers often turn to analogues, and there is nothing wrong with that. The main thing is to choose the right product correctly.

A clean filter element is the key to good car acceleration, fuel economy, and efficient engine operation. Some motorists themselves negatively affect engine performance by violating the regulations for checking the replacement of the air filter. Any driver can cope with its replacement without special knowledge and experience in carrying out similar work. On auto sites you can find many videos about replacing this element. But you should be as careful as possible, since any error during installation can lead to the supply of clogged air to the engine.