Nissan Almera classic how long does it take to replace the timing chain

Almost all Nissan Almera engines, including the Nissan Almera Classic 1.6, are equipped with a timing chain drive. There are only some engines that the manufacturer has equipped with a timing belt drive. The gas distribution in it has phases that open at the right moment, and this reduces gasoline consumption and exhaust pollution.

The good thing about the chain is that it provides maximum performance during the first 150–200 thousand km; it almost never breaks, it only stretches and shifts, which protects the valves from damage.

Replacing the chain and belt is carried out according to the advice of the developers. But sometimes the on-board driver tells you about errors 0330 and 0340. These errors indicate that the phases of the shaft sensor have shifted. An oscilloscope will help you find out exactly the cause of the error, but in most cases this indicates a stretched circuit. And in this situation it is already necessary to change it. Another prerequisite for replacement is increased gasoline consumption and regular, incomprehensible sounds of metal knocking coming from under the hood.

If you experience such signs, then replacing the timing chain on a Nissan Almera H16 is mandatory:

Errors 0335 and 0340 appear.
When the engine is idling, extraneous ringing noises are heard.
The engine often fails to start the first time.
When idling, unstable speed appears.
When you move, jerks appear and the engine loses performance.

The nuances of replacing the timing chain in Nissan

Many modern Nissan car engines are equipped with a chain drive gas distribution mechanism. Since the life of the chain is twice as long as the life of the timing belt, the motors are more reliable and, accordingly, are in increasing demand.

Timing chains for Nissan have their own advantages and disadvantages. The first includes the service life of the drive - it does not need to be replaced before noise appears; in some cases, cars have been driven with one chain for up to 500 thousand km.

Drive malfunctions can be judged by a characteristic tone similar to the sound of a running diesel engine. The problem may not lie in the drive itself, but may be caused by a failure of the tensioner or wear of the dampers. However, when faced with a sound uncharacteristic of the engine, the car owner is unlikely to ignore it without taking measures to identify the cause and eliminate the malfunction. A timing belt break always occurs unexpectedly, entailing bending of the valves in the cylinder head and significant costs for repair work.

The chain drive also has certain disadvantages:

increased noise during operation, even if the mechanism is working properly;
more complex replacement compared to a belt;
increased cost of spare parts.

Basically, Nissan chain-driven gasoline engines consist of a four-valve cylinder, two camshafts installed in the main cylinder block. Replacing the timing chain on a Nissan requires disassembling the front part of the engine, i.e. dismantling:

generator (air conditioning) belt;
crankshaft pulley;
valve cover;
front cover of the internal combustion engine;
camshaft sprockets;
engine mounting bracket (support) – if necessary;
engine crankcase.

The procedure for dismantling engine elements for subsequent replacement of the Nissan timing chain depends on the model of the internal combustion engine, the complexity of its design (for example, the Nissan Maxima power unit has a more complex design compared to the Nissan Almera internal combustion engine, and accordingly, the work will be more labor-intensive). In addition, a number of motors (such as GA 16) have two circuits:

the first transmits motion from the crankshaft to the intermediate gear;
with the help of the second, the movement is transmitted from the intermediate gear to the camshafts.

Chain drive malfunctions can be judged by:

Engine control system errors: - 0335 - indicates problems with the crankshaft; - 340 - probable camshaft malfunctions.
Problems starting the engine.
Floating speed at idle.
Feeling of failure of internal combustion engine traction while driving.
Uncharacteristic metallic sounds.

Significant stretching of the chain drive will cause a Check Engine light to appear on the dashboard, indicating errors generated by the crankshaft or camshaft sensors. A cold engine start may be accompanied by a characteristic metallic sound. Such symptoms require immediate contact to a service center.

Assembly

Assembly of the mechanism occurs in reverse. In this case, the engine will have to be cleaned of traces of used sealant, dirt and degreased. Installation of a new chain should be carried out in such a way that all marks match.

When installing the oil pump, we change all the seal rings. It is worth replacing them even if they have no visual defects. A layer of new sealant is applied to the engine panel, but you need to take into account the fact that in this case a sealant that can withstand high temperatures will do. We fasten the side cover and wait for the sealant to settle. We install the pump and a pre-prepared new gasket. Now the pulley is installed on the water pump, after which all the necessary bolts are tightened. On the valve cover, the old gasket is replaced with a new one. Now the pan and muffler return to their place.

All bolts should be tightened to the limit. That's basically it. Now the timing chain has been replaced with a new one, and this was done on our own, without the involvement of specialists, whose services, by the way, are not cheap at all.

How to tension the Almera N16 chain?

Almerovodians! Please tell me how to tighten the chain, otherwise the engine has become noisier. Thank you in advance !

and why? it is practically eternal on these engines.

What's the mileage? Maybe the chain needs to be changed?

The chain runs until 100k, then inspected. They tighten it by 200 thousand.

she pulls herself up

Give me some advice. The situation is this: I decided to replace the piston rings on my own, read a lot of manuals, topics on the forum, put my hands on my feet and rushed. I took everything apart, got to the timing chain, started cranking the crankshaft, heard something like “trrrk.” It seemed (or maybe it didn’t seem) that with this sound my chain was knocked a couple of links. Maybe she poked, maybe she didn't. Because before cranking, due to mystical circumstances, I took out the chain tensioner (apparently I was reading the manuals) and when I cranked it further, in order to set the yellow marks on the camshaft marks, I didn’t hear any more slips. I set everything up, and it is quite possible that the crankshaft also turned out to be the first piston at TDC, as it should be. And perhaps it didn’t turn out to be.

Replacing a component yourself

Want to save money? It is quite possible to replace the chain with your own hands. However, this task is not an easy one, so it is better not for a beginner to take on it. Expect to spend at least 3-4 hours. You also need to prepare a place and a set of tools in advance.

Let's look at the process of replacing a chain using the Nissan Almera N16 Classic as an example.

Platform and tools

It is advisable to carry out the work where there is a lift, overpass or pit. Prepare the following tools:

hex key 6;
socket heads sizes 12, 13 and 14;
chisel and hammer;
clean cloth for wiping;
containers into which technical fluids will need to be drained;
adjustable and torque wrenches;
block of wood;
sealant and “anti-silicone” (degreaser);
and, of course, a new chain.

Preparatory stage

Such a serious event requires careful preparation. First of all, this concerns the necessary preparations:

hex key 6;
heads size 12,13, 14;
hammer;
chisels;
torque wrench;
sealant;
degreaser;
rags or rags;
containers for coolant and oil;
adjustable wrench;
wooden block;
new part - timing chain.

Preparatory stage for replacing the Nissan Almera timing chain

Replacing a belt on a Nissan Almera Classic also concerns safety issues. They embody the following points :

Disconnect the cable from the ignition coil. Turn off power.
Unscrew and remove the coils.
Label each with consecutive numbers for correct installation during installation.
Disconnect the air pipes from the valve cover.
Following the instructions, unscrew the fastening bolts on the valve cover around the perimeter. Take it off.
Remove the right cushion (it may interfere with the subsequent removal of engine parts).

Timing replacement for Nissan Almera Classic 1.6

Replacing a chain or timing belt Nissan Almeria Do it yourself

The Nissan Almera G15 timing chain has been replaced with a station with all the necessary rules, but it will cost you a lot of money. You can do the work yourself so you don't have to open your own wallet. All you need to do is follow all instructions strictly to avoid making the situation worse.

How do you know what conditions need to be catered for?

Almost all Nissan Almera engines, including the Nissan Almera Classic 1.6, are equipped with a synchronization chain drive. There are only some engines that the manufacturer has equipped with a belt-driven throttle distribution mechanism. Do-it-yourself Peugeot 307 1.6 hdi timing belt replacement on video. The rear wheels of the Nissan Almera Classic are equipped with drum brakes. Nissan laptop circuit replacement. It's time to replace your Nissan timing chain on your Nissan Qashqai 1.6 and 2.0. The gas distribution in it has phases that open at the right time, and this reduces gasoline consumption and exhaust pollution.

The good thing about the chain is that it gives maximum performance during the first 150–200 thousand km, it practically does not break, it only stretches and moves, which protects the valves from damage.

Changing the chain and belt is carried out on the advice of the developers. But from time to time the flight attendant reports errors 0330 and 0340. These errors indicate that the phases have shifted from the shaft sensor. Detailed 3-part video about replacing the timing belt roller and replacing the timing belt 1.4 1.6. Skoda An oscilloscope can help you determine the cause of the error, but it almost always says the circuit is too long. And in this situation, this needs to change. Self-test and replacement Nissan Almera 1.6, 102 hp. Engine timing belt Another condition for replacement is an increase in gasoline mileage, constant strange sounds of metal knocking from under the hood.

If you experience these symptoms, timing chain replacement for Nissan Almera N16 is inevitable:

Errors 0335 and 0340 appear.
When the engine is idling, an extraneous hum is heard.
At first the engine often does not start.
Unstable turns occur while idle.
When jerking, jerking occurs and the engine loses performance.

How to change a product

It should be noted that replacing the synchronization circuit in the Nissan Almera N16 will cost you 8-10 thousand rubles, if you do it without outside help, you will still save a lot.

Replacement must be done on a lift or using a pit. This is necessary for faster and easier access to the right place.

Wooden block.
Hammer.
Sealant.
Degreaser
Adjustable wrench.
Test containers and antifreeze.
Chisel.
Wrench.
Hexagons, heads.
Unreliable fabrics.

For Nissan Almera, replacement should be in the following order:

Turn off all ignition coils and unscrew them. Make sure you sign them so you don't get confused about their location and run into problems.
The air connections must be disconnected from the valve cover.
Locate the mounting bolts, then unscrew them and remove the valve cover.
We find the right pillow and carefully remove it.
Drain as much old oil as there is in the engine.
We find and carefully disassemble the oil filter.

Drain the coolant, but to do this, remove the clamp in the lower radiator tube.
We drain the coolant from the cooling system by unscrewing the cap on the radiator.
Carefully remove the radiator and then the drive belt.
You need to find the inlet hose and then remove it.
We find and disassemble the head in the cylinder block.
Remove the muffler, find and unscrew the oil.
We find the bolts that hold the pump pulley in place need to be loosened.
We find and remove the straps from the accessories.
Take the strip we prepared and insert it between the crankshaft and the crankcase surface.
Also remove the crankshaft pulley. Replacing the timing belt vw passat b5. Walkthrough video. Part 1. Take your time, do everything carefully.
Unscrew and remove the pulley in the water pump.
Remove the oil pump.
Installing the first piston at TDC (top position). Look closely at the tags, they correspond to almost every available option.
We fix the camshaft using an adjustable wrench, and then unscrew the gear bolts.
We shoot in a certain order:

Timing chain replaced on Nissan Almera Classic 2008 QG16DE Nissan Almeria Classic

Changing the timing

on
Nissan Almera Classic
QG16DE 2008 Nissan Almera Classic Thanks for watching and for.

NISSAN ALMERA Ice K4M not very much about replacing the timing belt

This video was edited by YouTube Video Editor (). The shaft lock size in this video is included.

upper damper strip;
tensioner;
damping tension plate.

The gas distribution mechanism (timing mechanism) has chains that must be removed.
We find the gear using a flathead screwdriver, insert it, and then take it out.
We clean all dirt and sealant from the engine side.
We mention the marks that should have come first in the replacement process and pay attention to them when installing the last chain.
The seals must be changed.
The new sealant is applied in place of the old one, that is, in place of the side surface of the engine.
The mounting bolts must be secure.
The side cover must be attached. Replacing the timing chain of Nissan Almera. Nissan Qashqai 1.6 and 2.0 replaced the timing belts with diesel ones. Nissan laptop circuit replacement. Spare spark plug Replacement for Nissan Qashqai 1.6 and 2.0 belts. And rear brake pads with replacement Nissan Almera N16 rear brake pads. Wait a minute for the sealant to settle.
The pump and gasket must be installed.
We reassemble everything carefully and carefully in reverse order.

Please note the urgent need to use tags! Otherwise, the circuit may break, and this will lead to critical consequences for the device.

Please note that replacing the timing chain on a Nissan Almera N16 requires basic knowledge of the design of your vehicle. But if you don't have any, you'll have at least a passing knowledge of photos or videos that you can easily find online before you take any action.

Belt replacement

The timing belt, through which the entire unit (camshaft and crankshaft) is driven, is responsible for ensuring high-quality operation of the gas distribution mechanism. In other words, this belt controls the input and output phases; no engine can do without it.

If the timing belt is a classic in 2013, 2014 or at least one other year, there is a failure, in other words, teeth breaking or cutting, this leads to very dangerous contact of the valves with the pistons, which will be a necessary condition for expensive repairs.

Naturally, such a moment is very unpleasant for any owner. To avoid this problem, you can replace the timing belt on Nissan Almeria yourself on the advice of manufacturers and specialists, and this is every 70-80 thousand km or every 3-4 years. But if you're suspicious about the belt, it's best to check, fix what needs to be done, and measure it rather than pay for an expensive repair.

Many people recommend replacing spark plugs with a belt because checking the belt will make the crankshaft spin easier. Check the toothed surface of your own belt for wrinkles, flaking, tooth cuts or any cracks. And on the back, look carefully for any signs of burns, wear, or exposed cord. Also check the ends, they may have ties or tears. Be sure to replace the timing belt if these signs (at least one from the entire list) or traces of oil are found.

Conclusion

It is better to replace the timing belt for Nissan Almera Classic by replacing the cooling system water pump, as it is located in a very inaccessible place. And when working on replacing the chain/belt, access to them will be much easier, which will be important for replacing the pump. Buy nissan almera classic suspension! Prices. Here you will find the fuel consumption of the Nissan Almera Classic and how much the Nissan Almera Classic eats in various conditions. Nissan Almeria Classic: Replacing brake pads on the brake mechanism Ubs video. By replacing your chain in Almeria yourself, you will save some money and spend about 4 hours. This process will be easier for you to do using an automatic lifting device or on an equipped track.

First of all, turn off the electrics - the terminals with the battery, disconnect the connectors from the ignition coil. It is better to unscrew the coils themselves. To avoid confusion later, these parts are numbered. Next, unscrew the valve cover fasteners and remove it. You can save the gasket, but it is better to replace it with a new one.

In order to gain access to the chain, the timing case is removed. The engine is lifted with a jack - the casing will rest against the suspension cushion. If the cushion is worn out, you can simply unscrew the fasteners.

Then drain the oil from the engine crankcase and the antifreeze from the cooling system. It is better to replace these fluids with new ones. To completely drain the oil, remove the pan. The exhaust pipe, which simply unscrews from the manifold, will interfere. At the same time, the gasket is also changed.

When the oil has completely drained, remove everything that may interfere with the process of replacing the timing chain on the Nissan Almera N16. This is the power steering, alternator and air conditioning belt. To do this, unscrew the pump pulley bolt and remove it. You can also remove the crankshaft gear at the same time so that it does not move from its axis. If you do not do this, you will have to manipulate the hydraulic tensioner and damper.

Before removing the old chain, the shafts are set in the correct position. There are corresponding marks on the cylinder block body. The first piston must be installed at TDC. All timing marks on the gears must match. This is achieved by rotating the crankshaft with a wrench. When the risks finally coincide, the shafts are fixed.

Replacing the timing belt

According to the maintenance regulations, the timing belt must be replaced no later than 4 years of operation, regardless of its condition. Damage to the belt will cause the valves to stick against the pistons. The reason for this is the displacement of the rotary angle of the camshaft and, accordingly, the crankshaft. This damage will cost the car owner dearly. Therefore, it is recommended that every time you undergo a technical inspection, you check and, if necessary, replace the belt.

The timing belt on the Nissan Almera H16 can be replaced with your own hands. To do this, you must perform the following steps. First of all, you should remove the serpentine belt. We turn the tensioner with an open-end wrench and stabilize it using the T10060A clamp.

The work should be performed in inspection pits or on an overpass. The formation of folds, small cracks, and separation of fabric from the rubber part is not allowed on the toothed part. The reverse side should be like new with no signs of wear. Under no circumstances should the cord threads be exposed, and there should be no signs of burning on the belt. Replacement is necessary if even the slightest traces of oil are found on the belt. We must not forget that the manufacturer requires changing the tension and support rollers along with the timing belt. It is also recommended to replace the drive pulley mounting bolt. The photo shows the consequences of a broken timing belt.

Customer Reviews

17 584 Everything is at the highest level as always

Review date: 01/26/2022	Author: Dmitry Alexandrovich
Model: X-Trail 2012	Reason for contact: Diagnostics
Address: Union Motors Medvedkovo

I have been using this service for several years now. As always, everything is at the highest level, the staff is responsive, friendly and, most importantly, they will sort everything out and explain...

Read the full review of Union Motors · Comments 1 · Like

14 679 Everything is fast and clear!

Review date: 01/10/2022	Author: Pavel
Model: Murano 2012	Reason for contact: Routine maintenance
Address: Union Motors Medvedkovo

Changed the engine oil quickly.
They showed the car at my request and selected stabilizer bushings. Everything is fine! Read the full review of Union Motors · Like

11 660 Always friendly staff

Review date: 01/07/2022	Author: Oksana
Model: Almera 2015	Reason for contact: Routine maintenance
Address: Union Motors Medvedkovo

... During the entire period of service, all shortcomings were eliminated immediately and did not bother us anymore. The technicians always clearly and competently explain the problem and the reasons that arose with the car. During the work process, photos and descriptions of the actions are sent...

Read the full review of Union Motors · Comments 1 · Like