Replacing the handbrake cable on a VAZ 2114 useful tips

The parking brake cable is the device that interacts with the brakes of the rear wheels. The well-known handbrake is now little used when stopping at an intersection, but on a manual VAZ-2114, for example, it is very convenient to use it on a steep descent.

When making turns, using the handbrake correctly can significantly reduce the turning radius. And if you have to jack up the car, it’s hard without a handbrake.

The handbrake should keep the car on the slope. To check, you need to park the car on level ground, put it on the handbrake and push it hard. If it starts to roll, then it’s time to change the cable.

How to replace the hand brake cable on a VAZ 2114

One of the main causes of malfunctions in the brake system is a failed parking brake cable. In addition to deformation, this part is also subject to frequent ruptures, which leads to the need to replace it. You can purchase a cable at any auto parts store, but we will look at how to change the parking brake cable on a VAZ 2114 in detail.

Handbrake cable

HANDBRAKE CABLE REPLACEMENT PROCEDURE

The moving parts of the brake system tend to wear out. The working condition of such parts must be diligently monitored, since brakes are an extremely important part of the car. Timely repairs and diagnostics will help protect yourself and your car from unforeseen situations. The most unpleasant breakdown is a broken parking brake cable.

If the cable breaks, it must be replaced immediately. We'll look at how to replace the handbrake cable below.

As in any other case, DIY repairs require some tools. First, you need to find a car overpass or a hole (as a last resort, you can use a jack, which we will need anyway). You also need to prepare certain tools, such as thirteen wrenches (preferably 2), pliers, a hammer, plastic clamps and gloves. And the actual new hand brake cable for the VAZ.

When everything you need is prepared, you can start working. Replacing the handbrake of a vase takes place in stages:

First of all, we put the car on an overpass or a pit, or jack it up and climb under the car;
By removing the muffler can from the mounts, we will greatly simplify our work. If this is not done, it will be difficult to unscrew the cable tension nut;
Unscrew the locknut and the adjusting nut of the handbrake. This concludes the work on the overpass for now;
We drive the car onto a flat surface and jack up the rear;
Remove the wheels;
We knock down the locking pins from the pads;
Remove the brake pads;
Now you need to disconnect the cable ends from the equalizer. This is where pliers come in handy; you can use them to remove the clamps;
You need to remove the cable loops from the hooks of the spacer lever;
Unscrew the bolt securing the cable sheath and remove it;
You can pull out the parking brake cable of the VAZ 2114.

Pulling a new cable will no longer be a problem. Similar to the removal procedure, we do everything in reverse order. We start by pulling through the washers and loops on the hooks of the lever, and finish by tightening the handbrake in the cabin. The cable sheath also needs to be replaced sometimes, as it is also subject to wear. You can secure it after replacement with ordinary plastic clamps. This is how the VAZ 2114 parking brake cable is replaced.

Replacement is carried out in a similar way on VAZ 2115 and VAZ 2113 cars. These models have an absolutely identical brake system, so there can be no differences in repairs. An exception may be “amateur tuning” or unscrupulous repairs inherited from the previous owner.

HOW TO ADJUST THE HANDBRAKE

Sometimes, after replacing the cable, it becomes necessary to adjust the brake. It's easy to check whether adjustments are needed. We put the car on the handbrake down the slope. If it moves, then it needs to be adjusted.

Incorrect operation of the handbrake is expressed not only in poor fixation of the car when using the parking brake. A creaking sound near the rear wheels also indicates that the cable tension needs to be loosened.

Adjusting the hand brake of the VAZ 2114 is quite simple:

It is necessary to remove the muffler from its mountings
Unscrew the parking brake lock nut
Tighten or loosen the nut, depending on the situation (if it doesn’t hold, tighten it, if it creaks, then loosen it).

The lever travel should be in the range of two to four clicks until it is completely locked. After this procedure, you need to check the car again on a hill.

REPLACEMENT AT CAR SERVICE

Why shouldn't you contact a car service? The answer is simple - not economically, and not always of high quality. It seems that the procedure is not complicated, but the cost of the work is daunting. In addition, at most service stations they try to slip in their own cable, which is also not cheap. The average price in a store will be 200 rubles, while the service can rip off 500 just for a part. The cost of the handbrake cable varies depending on the manufacturer.

By making the replacement yourself, you will know exactly how well the work was done. Replacing the handbrake cable of a VAZ 2114 is a responsible matter. If you do everything according to the instructions, then there should be no problems. The main thing is not to forget about safety precautions.

Replacing the handbrake cable with your own hands is not a difficult task

WHICH CABLE TO CHOOSE

When choosing any car part, you must first of all be guided by its compatibility with your specific brand. Obviously, the cable from Chevrolet will not fit the Zhiguli. But there are times when people purchase unsuitable cables.

In our case, it is difficult to confuse anything. The handbrake cable of the VAZ 2114 is exactly the same as that of similar models of the domestic manufacturer. It can be found at any auto parts store. Several manufacturers produce cables, and all are usually of the same quality. This is understandable, the detail is not complicated.

There shouldn't be any problems when choosing. The prices are quite reasonable and there is not much difference. The only thing worth doing is to read on the packaging about compatibility with your car, just in case.

After following all the instructions, you can replace the handbrake cable on VAZ cars yourself. This will have to be done quite often, due to the design features of the brake system and its fragility. Having such skills is always useful. Now you know how to change the parking brake cable on a VAZ 2114.

HOW TO ADJUST THE HANDBRAKE

Incorrect operation of the handbrake is expressed not only in poor fixation of the car when using the parking brake. A creaking sound near the rear wheels also indicates that the cable tension needs to be loosened.

Adjusting the hand brake of the VAZ 2114 is quite simple:

It is necessary to remove the muffler from its mountings
Unscrew the parking brake lock nut
Tighten or loosen the nut, depending on the situation (if it doesn’t hold, tighten it, if it creaks, then loosen it).

The lever travel should be in the range of two to four clicks until it is completely locked. After this procedure, you need to check the car again on a hill.

When is it necessary to replace the handbrake cable?

VAZ 2114 parking brake cable - it is with its help that we interact with the rear wheel brakes (brake drums). Another name for the handbrake is the parking brake. Many people think that they can live well without it, they say, who even puts the handbrake on their feet these days? But don’t forget that the fourteenth is a manual transmission, with our downhill traffic jams the handbrake is very useful, and also, in the parking lot, the chance of the car being stolen is sharply reduced, plus you can take turns in the winter effectively! Anyone who has ever jacked up a car themselves knows about the need to put the handbrake on. If you come up with a hand brake for your car, it should work properly. But it doesn't always work.

Handbrake cable

Hint of replacement

Elementary wear of a part - the handbrake cable may rust, break or become loose so that it cannot be tightened - this is the most common reason for replacement. The two rear wheels seem to hint that the parking brake is connected to the wheels in the form of two cables. Almost always one of the cables fails. This does not mean that one needs to be changed. Buy a set and change both. The price for a VAZ 2114 parking brake cable varies from 200 to 1000 rubles (depending on the manufacturer and place of purchase). Otherwise, the cable that turns out to be older will definitely fly in the near future, and you will simply pay double the price.

Symptoms of a cable failure are usually as follows:

The handbrake does not hold the required traction
brake drums get hot
when pulling the handbrake, the cable may not respond to the action
the cable sheath is worn out

It’s easy to check if something is wrong with the cable: put the car on the handbrake, get out of it and try to give it a good push – it will roll a little if the cable is dead.

How to remove the handbrake cable on the fourteenth?

Before changing the handbrake cable on a VAZ 2114, it must be removed. Fortunately, it is clearly visible and cannot be confused with anything. You need to work in a hole or on an overpass under the bottom of the car. It’s good if the car is clean, because all the nuts and fasteners need to be found and unscrewed (you can also spray them with WD for a smooth fastening movement); dirty ones will take longer to work with. Before replacing, move the handbrake all the way down.

We start with the locknut and the adjusting nut, loosen them and remove them from the handbrake rod (now you can remove the washers and cable leveler, or you can do this after jacking up the car, before removing the wheels).
Jack up the rear of the car, unscrew the wheel bolts and remove the wheels.
To remove the brake drums, tap the locking pins to dislodge them from the shoes.
Remove the brake pad.
We disconnect the tip of the first and second cables from the equalizer (the clamps can be removed with simple pliers).
Remove the cable loop from the hook of the shifted spacer lever of each wheel.
We remove the cable sheath from the entire rear suspension, having first unscrewed the fastening bolt.
Pull the cable out of the holes in the brake flaps.

Adjusting the handbrake tension
Replacing the handbrake cable of a VAZ 2114, the process is similar to removal, only in reverse order. We start by threading the new cables into the washers, attaching the loops (many people make special clamps at the end of the loop - bosses - so that the cable sits even more tightly in place), and assembling the entire wheel hub. They laid each cable along the suspension and secured it. In the end, you will need to tighten the handbrake in the cabin itself.

By the way, the parking brake is the cause of the unpleasant squeaking sound in the rear of the cabin. Replacing the VAZ 2114 parking brake cable is a good reason to get rid of it for one thing: you should come up with a rubber seal for attaching the cable to the body frames.

After replacing the old cable with a new one, we check how it works. Just put your fourteenth on the hill on the handbrake, if it moves, you need to adjust it:

We loosen the lock nut of the tension device in the handbrake, and tighten the adjusting nut, then pull the cable with a lever.
The lever should move 2-4 strokes (this is the working stroke of the handbrake), if it works, tighten the lock nut.
We drive up the hill again, put the handbrake on, check how it holds.

Before frost, you should always remove and lubricate the handbrake cable; you will increase its service life, protecting it from the adverse effects of low temperatures. Thus, you will ensure stable operation of the entire brake system of the car. It is worth lubricating the axle itself, the tips and the equalizer rod.

One more point: the handbrake cable does not always need to be changed, excluding, of course, an obvious rupture or wear of the mechanism. Most often it just needs to be tightened. And your handbrake will be back to normal. Tightening also means that the cable gradually becomes unusable, and it will soon have to be replaced with a new one. Also, the brake pads may be acting up. Very often, especially after tightening, drivers sin on the handbrake cable, buy a new one, change it, but there is zero effect. Look at the pads, they also tend to run out.

Replacing the handbrake cable on a VAZ-2113, 2114, 2115

When making turns, using the handbrake correctly can significantly reduce the turning radius. And if you have to jack up the car, it’s hard without a handbrake.

Cable faults

Over time, the cable stretches. Doesn't hold the car even after being pulled up.
The cable threads begin to break.
The cable itself broke.
Even after lubrication, the cable has difficulty moving in the sheath.
The cable becomes sour.

The parking brake can often be restored to normal function by lubricating the cable. If you carry out this procedure regularly once a year (usually this is done before frost), then you can forget about situations when the handbrake fails.

The cable will last longer as it will be well protected from freezing. The brake system will work stably. You need to lubricate the axle, equalizer rod and tips.

Please note that there are two cables going to the wheels; it is recommended to replace them at the same time. Otherwise, the old one will fail earlier and you will have to do double work, which we will discuss below.

Why change

If you notice problems with the handbrake but continue to use it, you may be in for an unpleasant surprise when the car suddenly rolls downhill.
It is also possible that the pads will not return to their original position. This already threatens to heat up the brake discs and wear out the pads. As a result, the wheel may jam. The effect will be the same as driving with a handbrake.

Rope price

The cable itself costs from 200 to 1000 rubles. The price depends on the manufacturer and place of purchase. Replacement at a car service center will cost on average from 400 to 1000 rubles, depending on the region.

Replacement

It is not difficult to independently replace the VAZ-2114 parking brake cable.

To replace you need the following tool:

key to “10”;
two keys to “13”;
a large screwdriver and WD-40 for smooth fastening.

Replacement is carried out on an inspection hole or overpass.

The handbrake must be lowered all the way down.
All parking brake nuts need to be cleaned. Don't forget about the leveling bar.
The locknut must be loosened and removed from the rod. The same is done with the adjusting nut.
Now they begin to remove the wheels. First loosen the wheel bolts. The rear part is lifted with a jack. Don't forget about the supports! Once they are aligned, you can remove the rear wheels.
Remove the brake drums using a hammer and a wooden spacer. You need to knock the locking pins off the pads.
The end of the parking brake cable of a VAZ-2114 car is attached to the rear brake shoe lever. First you need to remove the block, and then the cable end.
Unscrew the fastening bolt and disconnect the cable sheath.
A cable is pulled out from the holes in the brake flaps on each side.
Then they take out the cable sheath from the fastenings on the body.

Bottom line

The cable has been removed. You can replace or lubricate the parking brake cable. Installing a new one is done in reverse order. Afterwards the tension of the handbrake is adjusted.

Preparing for work

To perform any work, as the site provaz2114.ru reports, you need to take care of the availability of tools and other devices that significantly facilitate the task. And replacing the handbrake cable of a VAZ 2114 will not seem laborious. To begin with, of course, you need the cable itself, which is available for sale in almost all relevant stores. The price is quite reasonable and depends on the manufacturer and there are no significant differences in cost, but the quality is the same. For model 2114, the handbrake cable is not a shortage. The only thing you need to do is carefully read the instructions on the cable packaging and make sure that it is the right cable. Then you need to clean the car from excess dirt.

How to change the parking brake cable on a VAZ 2114

The parking brake is an important element of the car. The main reason for unit failure is wear of the cables. Some motorists are in no hurry to make repairs, mistakenly believing that the handbrake is a secondary safety measure. Not having a parking brake can be costly. It's not just about money. It’s enough to just imagine what will happen if the car fails to stay on a high rise and rolls out of control onto a busy section of the street. Don't tempt fate. If the parking brake breaks, repair it immediately. We will tell you how to tighten the handbrake on a VAZ-2114.

The main reason for the failure of the VAZ-2114 handbrake is wear of the cables

SIGNS OF BREAKAGE

Structurally, the brake system includes two cables. As a rule, only one of them breaks. However, it is better to buy and replace both products at once. There are two reasons for this:

the second worn cable will also soon fail and will have to be replaced (again returning to the repair problem);
a set is cheaper than buying products one by one.

Depending on the manufacturer and store, purchasing a kit for a VAZ-2114 car will cost you 800–1000 rubles.

Signs that clearly indicate that it is time for repairs:

the parking brake does not hold the required traction;
it is unusual for the brake drums to overheat;
a visual inspection shows that the protective sheath of the cable is clearly frayed;
When the parking brake lever is pulled, the car does not lock. This is easy to check. Push the car while it is on the handbrake. If the car rolls, the breakdown is obvious.

Structurally, the handbrake system includes two cables, but usually only one breaks

REPAIR

Replacing the VAZ-2114 hand brake cable is carried out on an overpass or in a garage pit. Pre-clean the bottom of the car from dirt (it will be much easier to work).

Operation sequence:

remove the rear wheels;
slightly unscrew the adjusting nuts and locknuts and remove them from the rod;
remove the equalizer;
dismantle the block and brake drums;
remove the tips from the equalizer;
remove the loops of the cables from the hook of the spacer lever;
unscrew the fastening bolt and remove the shell;
We take out the cables from the holes in the brake flaps.

Replacing the VAZ-2114 parking brake cable is carried out in the reverse order.

After installing the cables, they need to be adjusted, otherwise the handbrake will not fully perform its function.

ADJUSTMENT

After installing a new product, it needs to be adjusted. Otherwise, the handbrake will not fully perform its functions.

Sequence of work:

loosen the locknut, use a lever to tighten the cable;
the working stroke of the parking brake lever is 2–4 strokes (it turns out that we tighten the locknut).

CONCLUSION

Lubricate brake system components, especially when preparing your vehicle for winter. We pay close attention to the axle, equalizer rod and tips. This will protect the products from corrosion, extend their service life and ensure reliable operation of the braking system.

Perhaps you had to tighten the handbrake? Share your experience with our readers in the comments. Any information would be very helpful.

Why the handbrake does not work on the VAZ 2107

Like any other part or mechanism, the handbrake cable tends to wear out and become unusable. The parking brake on the VAZ 2107 is activated using a lever located in the middle part of the car between the driver and passenger seats.

Periodically, the handbrake cable should be tightened, as it becomes weakened, which leads to a decrease in the efficiency of the device. The reasons why the handbrake on the “seven” may not function are due to the following factors:

Excessive cable stretch.
Damage to the cable.
Malfunction of the brake mechanism in the rear wheel drums.

During prolonged use of the car, when the handbrake is constantly used, owners are faced with the need to periodically restore the cable tension. Over time, the device in question stretches, and there is nowhere to tighten it. The only way out of the situation is to exchange the product for a new one. It is recommended to carry out work on replacing the handbrake cable in an inspection hole, but you can do without it.

Changing the handbrake cable

Replacing the handbrake cable on a VAZ 2107 car begins with the fact that it is first necessary to dismantle the brake drums of the rear wheels

After dismantling the brake drums, you should pay attention to the condition of the rear brake pads and working cylinders. The presence of traces of fluid leakage will indicate that the mechanisms also need repair

Each owner of his car decides individually when it is necessary to change the handbrake cable. It all depends on the degree of wear of the cable. The procedure for replacing the parking brake cable is divided into 2 stages: dismantling and installation, as well as adjusting the tension.

The replacement algorithm is as follows:

After the rear wheels and brake drums are removed, you need to go down into the inspection hole and find the tension adjusting rod. This rod is equipped with a spring, which must be removed using a screwdriver.
Both nuts are unscrewed, after which the adjustment bar is removed. Next, the rear and front handbrake cables are dismantled.
Using a wrench, you need to unscrew the two nuts securing the two brackets. These brackets prevent the cable from falling. There are screws under the nuts that prevent them from unscrewing on their own.
After this, you should remove the rear brake drums and remove the springs that secure the brake pads. The pads can also be replaced if they show excessive wear.
Next, you need to pull the cable to disengage it from the bracket against which it rests.
The brake pads are removed. There is no need to remove both pads on the wheel. To replace the rear cable, you only need to remove one rear brake pad.
Now you should unscrew two fixing bolts from the back of the brake shield of both wheels. With their help, the cable tip is fixed. After unscrewing these two bolts, you should pull the cable, as shown in the photo below.
Using a 10mm wrench, you need to unscrew the front cable mounting brackets. After unscrewing the bolt, carefully remove the roller. To remove the roller, you need to roll it forward in the direction of the tip.
To remove the front part of the device, you need to pull on the product to remove it from the bracket and intermediate support structure.
After this, you need to get out of the hole and go into the car interior. When performing work, the handbrake must be in its lowest position. Inside, unscrew the two screws securing the handle trim.
There are 4 bolts under the cladding that need to be unscrewed. After unscrewing them, you will need to remove the handle along with the front cable.
To disconnect the cable mount from the handle, you will need to use pliers to remove the small cotter pin that secures the device to the handbrake handle.
After this, the device can be completely removed from the car and a new cable installed in its place. The installation process of both products is carried out in the reverse order of removal. After this, you should secure them and begin the tension adjustment procedure.

Adjusting the hand brake VAZ 2107

Adjustment of the handbrake should be performed not only periodically when the parking brake is lost, but also after replacing the cable. In order to adjust the cable tension, you will need to take the following tools:

pliers;
two keys for 13;
a can of WD-40 lubricant.

Handbrake tension on VAZ 2114

The VAZ 2114 car has good performance, reliability and maintainability. But this does not allow you to completely insure yourself against possible breakdowns.

Considering the state of domestic roads, it is not surprising that most often car owners turn to service stations with problems in the braking system or suspension.

A striking example of a breakdown is problems with the handbrake. More precisely, with cables that are responsible for blocking the rear wheels and do not allow the car to move until the handbrake is returned to its original position.

Whether you use a handbrake or not, sooner or later you will need to use the system. And if the handbrake has to survive regularly, then there is no debate at all regarding the need to urgently solve the problem.

Handbrake cable

Design

Many people mistakenly believe that the handbrake is a simple lever located near the gearbox, on the right hand of the driver. In fact, it is a whole system of elements that are connected to each other.

When the hand brake fails, in 90% of cases the culprit is a cable or a pair of cables that go to the rear brake pads from the equalizer.

To determine the reasons for the failure of the handbrake, it is necessary to understand the circuit diagram of the device and its components.

Handbrake diagram

The device includes a number of structural elements. Namely:

Lever arm;
Traction;
Springs;
Lever button;
Main cable axis;
Bolts;
Washers;
Drive unit;
Equalizer;
Case;
Locknuts;
Cotter pins;
Right and left lever;
Expansion left and right strip;
Lock washer, etc.

Malfunctions and their symptoms

Determining that a cable needs adjustment or replacement is quite simple. Signs of a faulty mechanism appear as follows:

The handbrake is pressed effortlessly - the cable is loose, you need to tighten it.
The mechanism does not respond to pressing the lever - the drive is torn or flew out, or the reason may be the wear of the rear pads.
If the handbrake is stuck, the drive is damaged and needs to be replaced.

Read more: Replacing the VAZ fuel filter

Having taken out the main element, you can visually determine its condition. Replacement is required in the following cases:

Up to 2% are damaged or torn.
The cable moves with difficulty even after applying lubricant.
The drive tips have grooves.

Tension

So, having understood the diagram, you can begin the procedure of tightening the handbrake cables.

Stretch

The tensioning procedure is as follows.

Place the car on an overpass or pit. If you don’t have a garage and you have the opportunity or desire to carry out the procedure at a service station, use a jack. The rear of the car is raised on a jack. The most extreme option is a curb onto which the car is driven and all you have to do is crawl under it.
Engage the gearbox in first gear and put the car on the handbrake by pulling the lever up.
The ideal number of handbrake clicks is from 2 to 5. If there are fewer or more clicks, it is easier to take appropriate measures to tension the cable.
If there are less than 2 clicks, then the cable will need to be lengthened. If there are more than five clicks, then the cables are shortened.
Lengthening the cable means relaxing it. To do this, unscrew the locknut. When tightening the cable, the locknut must be tightened in reverse.
Before you start looking for the required nut on the bottom of the car, release the handbrake lever all the way.
Take a 13mm wrench under the car and head down.
Find the handbrake cable equalizer. This is the same element from which the main handbrake cable is divided into two cables.
In some cases, it is simply not possible to gain access to the equalizer, since the muffler holders made of rubber are in the way. In such a situation, it is better to remove them. This is not difficult to do, but working with the handbrake will be much easier.
Now there are two nuts in front of you. One is a simple nut and the other is a lock nut. Having two keys in your hands, fix the nut with the first one, and with the second one begin to unscrew or tighten the locking nut. Be careful that the nut does not start to turn.
Taking into account the condition of the handbrake and the need to loosen or tighten the lever, turn the locknut in the appropriate direction. Remember what is the optimal number of clicks.
Tighten or unscrew the locknut to obtain the required degree of tension.

Examination

But if you twisted the nuts there, this is not a guarantee that the handbrake now works perfectly. This needs to be clearly verified.

To do this, it is enough to go through a successive stage of verification activities.

Stage	Explanation
Spin the wheels after tensioning is completed	The wheels are lifted one by one on a jack. When the handbrake lever is turned off, they should rotate freely without obstacles. By squeezing the brake, the wheels should lock.
Drive up a slight slope, stop and engage the handbrake	The fact that the wheels do not spin when suspended is good. But you need to make sure that the handbrake holds the car even when exposed to gravity.

If the check shows that the handbrake still does not hold, even if the cable was tensioned exactly according to the instructions, the handbrake is probably simply worn out and the cable needs to be replaced.

Signs that replacement is needed

It is not uncommon for the VAZ 2114 handbrake cable to rust, as a result of which it breaks or weakens so much that no tightening can restore its previous functionality.

At the first sign of cable wear, you should consider replacing it. This problem may manifest itself as follows:

The handbrake is not able to withstand the required traction;
Drum brakes overheat;
When you pull the parking brake lever, the cable does not respond to your actions;
The cable sheath is seriously worn.

To check the operation of the handbrake, it is enough to perform one simple action. Place the car on a level surface, apply the handbrake, get out of the car and try to push it hard. If movement begins, the cable is dead and needs urgent replacement.

What tool is needed to replace and tighten the parking brake cable?

Prepare the tools you cannot do without during dismantling:

2 keys for 13,
hammer,
pliers,
gloves,
jack,
clamps.

And also a liquid called “liquid wrench” to unscrew rusted nuts without problems. It is advisable to have a pit or overpass. If it is not there, then, by showing ingenuity, you can build something similar from improvised means, not forgetting about safety precautions. Or use a jack.

Dismantling and replacement

It is difficult to confuse the cable from the handbrake with anything else under the bottom of your VAZ 2114, which greatly simplifies the repair and replacement procedure.

Dismantling works

We provide detailed instructions for replacement, and additionally recommend watching the video.

We advise you to get the car in order in terms of cleanliness in advance. This will make it easier for you to find all the nuts and fasteners.
Additionally, treat the nuts with the almighty WD40. This will make it much easier for you to unscrew the sometimes sticking and rusting nuts.
Place the handbrake lever all the way down.
Start with the adjusting nut and locknut that you used recently to try to tighten a loose cable. In this situation, you should loosen the nuts and remove them from the handbrake rod.
Remove the washers and cable equalizer. Although this can be done after you jack up the car. But be sure to do it before removing the wheels.
Raise the rear of the car with a jack, unscrew the wheel bolts and remove them.
Tap the brake drum locking pins. This will allow them to be removed from the brake pads.
Remove the block.
You now need to disconnect the ends of the two cables from the equalizer. The fasteners can be removed from their places with the simplest pliers, so don’t bother.
The shifted spacer lever has hooks from which the cable loop can be removed.
The cable sheath must be removed from the entire suspension of the rear of the car. To do this, the mounting bolts are first unscrewed.
Pull the cable out of the holes through the brake flaps.
We got rid of the old cable, so all that remains is to replace the old one with a new element. The procedure is performed exactly in reverse order.
Thread the new cables through the washers and hook the loops. You can additionally make bosses - this is a special clamp that allows you to fix the cable even more tightly.
Reassemble the entire disassembled wheel structure.
Route the cable along the suspension through the sheath and secure the bolts.
Pull the handbrake in the cabin.
Check the correct tension and operation of the new hand brake, or rather the cable.

It is not uncommon for the parking brake to cause an unpleasant squeaking noise from the rear. By changing the cable, you can get rid of this problem at the same time. To do this, rubber seals are installed under the cable fasteners on the body frames.