Lada Kalina 1
The first generation was produced in 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012 and 2013 under the internal serial numbers
VAZ-1117, VAZ-1118, VAZ-1119
with sedan, hatchback, and station wagon bodies. In this article we will show a description of fuses and relays of the 1st generation Lada Kalina with block diagrams and photographs. Note the fuse responsible for the cigarette lighter.
The design of the blocks and the purpose of the elements in them may differ from those presented and depend on the year of manufacture and level of equipment of your Lada Kalina. Check the description with yours, printed on the back of the protective cover, or other technical documentation.
Differences in electronics of Lada Kalina 1 from Kalina 2
These two cars, despite their external similarities and common base, have different electrical wiring structures.
The second generation used Renault's developments, which explains the appearance of a body electronics unit, like on the Lada Vesta. In addition, these cars received completely different mounting blocks and their location.
The difference in the mounting blocks is also explained by the appearance on the Lada Kalina 2 of an automatic transmission, climate control and heated windshield. In addition, almost all trim levels now have DRLs. Therefore, diagnosing faults related to blown fuses on these machines is carried out differently.
4 Why reverse gear does not engage - other reasons
If the described methods for restoring the normal functioning of the gearbox did not help, most likely we encountered problems in the mechanical part of the gearbox:
- the spring burst;
- the retaining bolt has been cut off;
- The device that secures the gearbox elements has broken.
These faults are truly complex. Such problems must be solved by car service specialists, since they will need to remove the gearbox, disassemble it, find the cause of the breakdown, and then fix the problem. All this takes more than one hour and requires the use of special tools. It is irrational to carry out such repairs at home.
Where are the fuses and relays located?
Depending on the generation of the car, the fuse blocks have differences, and, consequently, different installation locations.
Location of fuse and relay blocks on Lada Kalina 1
The first generation Kalinas were equipped with several fuse blocks at once. Their location has several places and they are all in the cabin:
- The main unit is located under the panel, to the left of the steering column.
- Another block was mounted under the cigarette lighter, next to the gearshift lever.
- Another mounting block is located under the dashboard, inside the central tunnel.
Where are the mounting blocks located in Lada Kalina 2
The second generation Lada Kalina has two fuse blocks. The main one is located inside the cabin, and in some trim levels it is also installed under the hood.
- One is located in the cabin, to the left of the steering column, under the cover.
- The additional fuse box is located in the engine compartment, to the right of the battery.
It is worth considering the location of the mounting block to avoid mistakes in diagnosing the car.
Mounting block in the engine compartment
A set of fuses is indicated for the “luxury” version. In other versions, individual fuses from this set may not be used.
Fuse no. | Current strength | Protected Circuits |
FF1 | 50A | Heated windshield |
FF2 | 60A | Generator |
FF3 | 60A | Generator |
FF4 | 40A (without air conditioning - 30A) | Electric radiator cooling fan |
FF5 | 50A | Electromechanical power steering |
FF6 | 40A | Anti-lock brake control unit |
Fuses located in the fuse box of the engine compartment of a car with the ERA-GLONASS function (in a variant):
# | Denomination | Protected circuit |
FF1 | 60A | Generator |
FF2 | 60A | Generator |
FF3 | 30A | Electric radiator cooling fan |
40A | Electric radiator cooling fan (version with air conditioning or climate control) | |
FF4 | 40A | Anti-Lock Brake Controller / Stability Control Controller |
FF5 | 25A | Anti-Lock Brake Controller / Stability Control Controller |
FF6 | 50A | Electric Power Steering Controller |
Attention!
The relay and fuse diagram may differ depending on the configuration and production date of the vehicle. Current diagrams of the mounting block are presented in the operating manual for the date of manufacture of the car (download from the official website for a hatchback or station wagon).
Let us remind you that you will find other useful instructions in the section Repair and operation of Lada Kalina 2.
Keywords: mounting block Lada Kalina | Lada Kalina torpedo
2 0 0 0 0 0
Share on social networks:
Correct selection and replacement of fuses on Kalina
The fuse in a car is a plastic product with two contacts, inside of which there is a fuse link.
Different fuses are designed for different current values and if this parameter is exceeded, the insert burns out. It is very important to install the same one in place of the required fuse and not make a mistake.
For example, if a 15 Ampere fuse is installed on the cigarette lighter, then it is no longer possible to install a 60 Ampere or 5 Ampere insert.
The fact is that with a high operating current, the device can burn out or melt the wiring in the event of a malfunction. And with a high current of 15 Amps, a 5 Ampere fuse may blow immediately after turning on the device, since it is not designed for such work.
Fuse links differ in color and amperage. Currently, the following colors and fuses are used in cars:
Color | Clearly | Operating current |
Brown-yellow | 5A | |
Brown | 7.5A | |
Red | 10A | |
Blue | 15A | |
Yellow | 20A | |
White | 25A | |
Green | 30A | |
Orange | 40A | |
Red | 50A | |
Blue | 60A |
Lada Kalina cars of the 1st and 2nd generations use blade fuses of the Norma and Maxi standards. The latter are used on Kalina 2 in the engine compartment and several of them are used on Lada Kalina 1 in the cabin.
To replace fuses, there is a special puller in the main unit, which is located in the lower right corner.
Backstage adjustment
Often after its repair, the Kalina does not engage reverse gear. The speed at which the pedal is pressed does not matter. Fifth gear will also disappear along with it. To eliminate the malfunction, it is necessary to adjust the position of the rocker. How to do it? You need to find the backstage clamp and loosen it.
Next, the lever is moved to the desired position (reverse or fifth speed). The clamp is tightened. You should check the effectiveness of the adjustment with the engine running. If after this you still cannot engage reverse gear on the Kalina, make the adjustment in first gear. Move the gearbox lever to the appropriate position, having first loosened the bolt. Turn the rocker drive counterclockwise until the lever rests against the reverse gear lock R. By adjusting the seating depth of the rocker on the gearbox driveshaft, you will restore the proper operation of the box.
How to select and replace a relay on Kalina
A relay in a car is used to remotely control consumers that require high currents.
For example, to activate the starter, the ignition switch contacts and its wiring will not be enough. Therefore, the lock serves only as a control device, and the relay closes the power contacts and the retractor relay circuit.
In cars of both generations, the most common 4 and 5-pin relays are used. However, two types of sizes are used here; this should be taken into account when selecting. It is better to look at the characteristics of the relay on the body and buy exactly the same one or show the required relay to an auto parts dealer. Automotive relays can vary in current strength, number and location of contacts.
To replace faulty relays and fuses on the Lada Kalina, use a special “pliers” tool, which is installed in the lower right corner. The larger ones are for relays, and the smaller ones are for fuses.
If, after replacing the fuse, it has blown again, you should not try to change it again; most likely there is a short circuit in the circuit and the car must be sent for more thorough diagnostics.
Replacement process
In order to change the cigarette lighter fuse of the Lada Kalina model, you need to get to the mounting block. It should be located behind the decorative panel, on the left side of the front console.
- We snap off the plastic clips.
- We take the tweezers located in the mounting block.
- We take out fuse No. 20 (first generation). Another protective element has No. 18 (second generation).
- Install a new fuse.
It is important that the value of the new part coincides with those recommended by the manufacturer (15 amps - first generation, 20 amps - second). Otherwise, there is a high probability of increased load on the circuit and tripping of the fuse. This may cause the wiring to melt, short circuit and fire.
Fuse and relay diagram in Kalina 1
As mentioned earlier, in the first generation Lada Kalina there are three fuse and relay blocks. Therefore, each should be considered separately.
Main unit
To understand which fuses are installed in the main unit and what they are responsible for, you should read the table:
Number | Operation current, A | What is he responsible for? |
F1 | 10 | Hazard alarm, direction indicators, anti-theft system (immobilizer), instrument panel |
F2 | 30 | Power windows |
F3 | 10 | Alarm |
F4 | 20 | Washer and wiper |
F5 | 25 | Electric power steering ECU and heater motor |
F6 | 20 | Horn |
F7 | 10 | Interior lamps, instrument panel |
F8 | 20 | Rear window defroster heating element |
F9 | 5 | Dimensions - right side of the vehicle |
F10 | 5 | Dimensions – left side of the vehicle |
F11 | 7,5 | Immobilizer control unit |
F12 | 7,5 | Low beam - right headlight |
F13 | 7,5 | Low beam - left headlight |
F14 | 10 | High beam - right headlight |
F15 | 10 | High beam - left block headlight |
F16 | 10 | PTF - right side |
F17 | 10 | PTF – left side |
F18 | 15 | Seat heating |
F19 | 10 | Anti-lock braking system ECU |
F20 | 15 | Cigarette lighter |
F21 | 10 | Reverse switch |
F22 | 15 | Standard alarm control unit |
F23 | 25 | EUR |
F24 | 7,5 | Email Air Conditioner Magnetic Clutch |
F25 | 30 | Power supply |
F26 | 25 | Anti-lock braking system ECU |
F27 | 50 | EUR |
F28 | 40 | ABS |
The last four fuses are backup and are necessary to replace blown ones.
To find out which relay is responsible for what in Lada Kalina 1, just study the following table:
Number | Designation |
K1 | Headlight wiper |
K2 | Power windows |
K3 | Starter |
K4 | Additional relay |
K5 | Relay-breaker for direction indicators and hazard warning lights |
K6 | Windshield wiper and washer |
K7 | High beam |
K8 | Horn |
K9 | PTF |
K10 | Heated rear window |
K11 | Seat heating element |
K12 | A/C compressor clutch |
Fuse box under the cigarette lighter
There are only three inserts installed here. The purpose of the fuses is to protect the circuits of the engine injection system.
Number | Current | Designation |
F1 | 15A | Main relay switching circuit |
F2 | 15A | Gasoline pump |
F3 | 15A | Constant “+” power supply to the ECU |
Fuse and relay box under console
Closes the power parts of the engine injection system. On the second generation of the car, almost all relays and fuses from here will go to the main mounting block.
1 | Low fan speed |
2 | Main relay |
3 | High fan speed |
4 | Fuel pump relay |
5 | Electric fan fuse |
6 | — |
Table of fuses and relays in Lada Kalina 2
Lada Kalina 2 is significantly different from its predecessor and has a slightly different block with a different arrangement of fuses.
Main unit in the cabin
To understand what the relays and fuses on Kalina 2 are responsible for, study the table:
Number | Operation current, A | Protected circuit |
F1 | 15 | Power supply to engine ECU, ignition coils, fuel injectors and electric fan |
F2 | 25 | UCH |
F3 | 15 | ECU and automatic transmission drive |
F4 | 15 | SRS ECU |
F5 | 7,5 | Engine ECU, instrument cluster, UCH, power steering, brake light, speed sensor, automatic transmission mode selector, heated window switch and relay and heated seats |
F6 | 7,5 | Reverse signal, automatic transmission controller, standard parking sensors and turn indicators |
F7 | 7,5 | Canister valve, power supply for camshaft sensor, oxygen sensor, mass air flow sensor and manifold absolute pressure sensor |
F8 | 25 | Heated mirrors and rear window |
F9 | 5 | Side lights on starboard side |
F10 | 5 | Side lights on the left side, instrument panel and key lights, license plate lights, glove box lights |
F11 | 5 | Rear PTF |
F12 | 10 | Low beam and headlight range control (right headlight) |
F13 | 10 | Low beam and headlight range control (left headlight unit) |
F14 | 10 | High beam - right side |
F15 | 10 | High beam - left side |
F16 | 10 | PTF front right |
F17 | 10 | PTF front left |
F18 | 15, 20 or 10 | Cigarette lighter and heated front seats |
F19 | 20, 7.5 or 5 | Central locking control unit and ABS unit power supply |
F20 | 15 | Horn |
F21 | 10 | Gasoline pump |
F22 | 15 | Front windows, windshield washers and rear wipers |
F23 | 5 | Power supply for instrument panel and diagnostic connector |
F24 | 7,5 | Compressor clutch and climate control unit power supply |
F25 | 7,5 | Interior lamp, brake light |
F26 | 25 or 10 | Anti-lock braking system or UCH valves |
F27 | 25 or 30 | ABS valves or heater motor |
F28 | 30 | Heater motor or climate control power supply |
F29 | Reserve | Reserve |
F30 | Reserve | Reserve |
F31 | 30 | Momentary activation of high beams, front door power windows or ABS valves |
F32 | 30 | Heater and climate control |
Relay designations in Kalina 2
Relay number | Designation |
K1 | Electric cooling fan |
K2 | Window lifters |
K3 | Starter control |
K4 | Ignition Load Relay |
K5 | Hazard warning and direction indicators |
K6 | Windshield wipers or heated front seats |
K7 | High beam |
K8 | Sound signal |
K9 | Low beam |
K10 | Heated mirrors and rear window |
K11 | Engine ECU ON Relay |
K12 | Gasoline pump |
K13 | Hazard or reverse lights |
K14 | Additional relay for emergency lights or cooling fan |
K15 | Heated windshield (two sections) |
K16 | Heated windshield (two sections) |
K17 | Air conditioning compressor |
Fuses under the hood of Kalina 2
Check out the engine compartment fuse table:
F1 | Heated glass or generator |
F2 | Generator |
F3 | Generator or cooling fans |
F4 | Cooling fan or ESP controller |
F5 | Power steering or ESP unit power supply |
F6 | Power supply for EUR or ABS pump |
Depending on the year of manufacture, different vehicle configurations may have different fuse designations.
Video instruction
Sometimes a complete replacement of the device is required. To do this, you need spare parts and a standard screwdriver. The order of work is as follows.
- Open the hood, find the battery and remove the negative terminal from it.
- We unscrew the three mounting bolts around the parking brake handle, which is located on top of the central tunnel. We dismantle the hand brake limit switch.
- We unscrew the rear fastening screw, as well as additional screws on the sides.
- Remove the cover from the gear lever, and then lift the tunnel cover.
- We disconnect the power plug coming to the electrical wiring circuit.
- We press the special latches that hold the device itself. Once it pops out, you can replace it.
- Next, we install the new part on the Lada Kalina and carry out the reassembly process.
The video below will help you understand where it is located and how to replace the cigarette lighter fuse of the Lada Kalina model.
PROMOTION: SALE OF NEW CAR 2022 PRODUCTION
Why do fuses blow and what are the symptoms?
Fuses never blow without a reason, and the Lada Kalina is no exception. Fuse links protect circuits from the following faults:
- Short circuit.
- Overload.
The task of the fuse is to save the electrical circuit: wiring, consumers and to prevent a fire caused by melting of wires or other parts of the electrical circuit.
A short circuit is one of the reasons for the melting of the insert, which most often occurs due to damage to the wires, a short circuit of the “plus” to body ground, or during an accident, as a result of which the harness or a separate wire was cut by a part of the body.
Overloads can be caused by the simultaneous operation of many consumers or when using low-quality compressors to inflate tires, powered from the cigarette lighter.
There is another reason, which occurs extremely rarely - the use of Chinese fuse-links, the operating current of which is slightly lower than that provided by the electrical circuit. Despite the fact that 15A may be indicated on the insert body, in fact, this figure may be lowered to 10.
The symptom of a blown fuse is complete failure of the consumer. For example, if the cigarette lighter does not work, then in 90% of cases, a blown fuse is to blame. To make sure of this, just open the lid, take out the fuse-link, guided by the table, and check its integrity. If this cannot be done visually, you can use a multimeter in dial mode.
A serviceable fuse should ring, but a blown fuse will show an open circuit on the device. If replacing the insert does not help, you will have to diagnose the fuse box or look for the problem elsewhere.
It is prohibited to use wire to repair the fuse! This may cause the wiring in the vehicle to catch fire.
Release bearing
This element is very reliable. But do not rule out its breakdown. How to determine that it is the release bearing that has failed? To do this, you need to squeeze the clutch with the engine running and listen to the operation of the box. If, when you release the pedal, the characteristic sound (rustling) intensifies and the reverse gear on the Kalina does not engage, the reasons are in the bearing. But not only this speed will turn on poorly. Often, due to the “squeeze”, subsequent gears do not work well. They have to be turned on with re-gas and double squeeze.