Car alarms Pandora and Pandect, developed and produced by the Kaluga NPO Telemetry since 2004, are considered one of the best representatives of their class: initially, maximum technical excellence was chosen as the main vector for product development. Back in the days when the use of primitive Microchip/Atmel controllers was the norm for top-end alarms, Pandora alarms already sported high-performance ARM Cortex controllers, which made it possible to expand the functionality and security of security systems.
But this also had a downside - Pandora alarms were created for professional installation, and it’s difficult to call them “user-friendly” in terms of settings. The power of the controllers made it possible to easily implement programming on them via a USB port without additional tricks. It is not without reason that one of the hallmarks of the installed Pandora is a hidden USB connector of unknown purpose - with its help the installer configured the system.
Alarm Pandora
Pandora is a car alarm system from a Russian manufacturer, recognized not only in our country, but also abroad. The history of car alarm production began back in 2004, and today they are already recognized technical and technological leaders among car anti-theft systems.
Pandora alarms are a combination of modern technology and a high degree of reliability.
They are equipped with a special dialogue encoding mechanism, thanks to which all data transmission is encrypted. Not a single car thief has been able to open it yet.
A wide range of devices allows you to select a security system for any car in accordance with the personal preferences and requirements of the car owner. You can find either an inexpensive kit for a budget car or create a multifunctional system with a hood lock and automatic transmission, GPS and GSM navigation for an expensive car.
Possible problems and their solutions
Like any other gadget, the Pandora alarm key fob often malfunctions. In most cases, they are associated with the inexperience of the car owner and non-compliance with programming rules.
Drivers often encounter this problem when all the settings are set correctly, the power unit starts and warms up at the appropriate temperature value or time interval, but after stopping, the autostart stops functioning. The cause of this problem may be the temperature dropping below the set parameter. As a result, the engine will refuse to start and the user will have to re-tune it. As an additional measure, you should check whether there is a temperature prohibition on starting.
Pandora security system models
Modern car alarm models are divided into two main categories: LX (Light) and DXL (DeLuxe).
- Pandora LX includes models that are the most affordable, but can easily ensure the complete safety of the car. These are LX 3030 models; LX 3050 (with auto start); LX 3257; LX 3297 (with CAN module).
- PandoraDXL is the most numerous category, representing mid- and high-end models. All devices in this category are distinguished by the mechanism of an interactive encryption algorithm, the presence of a multifunctional sensor, the ability to connect via CAN, low current consumption and the ability to connect GPS - GLONASS and GSM units.
Minuses
The above disadvantages most likely apply to cars with a manual transmission.
- Fuel consumption increases.
- In winter, icing of the exhaust pipe occurs (this occurs due to water condensation that forms in the exhaust system).
- In winter, freezing of handbrake cables or brake pads (when the car is parked in neutral).
- If the car is parked on a slope, the handbrake mechanism is weakened - there is a risk of the vehicle moving spontaneously.
- At the moment the autostart is turned on, there is a threat of vehicle theft, since the security system is turned off at this time.
The car owner, only after meaningfully weighing all the pros and cons of autostart, will be able to decide whether it is worth installing the system on his vehicle.
Automatic car start from a key fob has both fans and opponents. There is controversy surrounding this system. Many car owners refuse this car alarm system, having heard a lot of various rumors and myths that have no evidence.
Myths about autorun:
- Independent movement of the car. The most common myth about autostart. And it is not without reason. A car rollback occurs if the driver leaves the car in gear after stopping. With the installation of this car alarm, you will have to change your habits. Now, after stopping, move the lever to neutral and put the vehicle on the handbrake.
- Freezing of brake pads. This myth becomes a reality only for those car owners who do not dry their brakes after driving in wet weather. This is easier to do than it seems. It is enough to perform several intensive braking. And if this problem does affect you, then a two-liter bottle of hot water will come to the rescue. You pour the fluid onto the rear brakes, and you are ready to go.
- Hijacking. Undoubtedly, a car with a running engine is a tasty morsel for a thief. Therefore, you should not use autostart in deserted places and at a considerable distance from the vehicle.
- Steering wheel locking occurs due to human inattention. This happens as follows: the car owner gets into the vehicle with the engine already running and forgets to insert the ignition key. This, in turn, leads to the steering wheel locking. The solution to this problem is to forcefully turn off the engine before driving.
Any problem with auto start from the alarm key fob can be solved. Therefore, the main obstacle to installing a car alarm is the reluctance of the vehicle owner.
>
Specifications
Pandora car alarms differ from their competitors in the high quality of their parts and their security against code reading and interception. Most keychains are made of ABS plastic, which makes them shock-resistant. All joints of the case are sealed, and the buttons have special stops. This allows you to prevent moisture from entering the electronic components of the transmitter and reduce the load on the pressing mechanism.
The control unit is made of sealed plastic. All necessary sensors and controllers are connected to it, like other systems, via waterproof multi-pin connectors. This solution reduces the likelihood of contact oxidation and reduces the frequency of maintenance. In the latest models, the architecture of the board and microcircuits has been redesigned, which makes it possible to achieve a high response speed to the control panel command. Also, the updated circuit increased the service life of the device.
Many of the latest models, in addition to a large number of functions, are released with a label. The installed radio tag will reduce the likelihood of theft, including such a type of car theft as “hijacking”.
Unlocking the trunk on a 2011 Toyota Corolla
Since there is no way to unlock the trunk, we organize its opening by analogy using a relay.
Red in the left kick panel - power cable for trunk release
We program one of the additional channels so that a minus appears on it when arming for 5 seconds. This channel controls two relays, with the help of which we organize the folding of the side mirrors on the car. With one relay we break the mirror folding wire (gray), with the second - the mirror folding wire (brown). The first relay supplies plus through the NR contacts to the motors, the second relay supplies minus to the motors through the NR contacts. This scheme works regardless of the position in which you left the side mirror folding button.
Gray – folding mirrors, brown – unfolding mirrors
Key Features
Pandora alarms are equipped with a large number of different functions, for example, a “turbo timer” and “anti-hijack”.
Main features of car alarms with feedback:
- Supports RFID tags and app control. This eliminates the need for large key rings.
- Most sensors are built inside the control unit. This simplifies installation and makes it faster.
- Setting up the system is done using software rather than analog. This achieves high accuracy and speed of work.
- The use of a large number of semiconductor elements in the circuit, which makes the controller energy-saving and smaller in size.
- Possibility to connect additional radio modules.
- Fast and easy software update via USB interface.
- Possibility of use as a mark for special Pandora watches.
Setup via Pandora Alarm Studio
The differences of this program are support for Bluetooth connection and work with a proprietary server that provides CLONE technology (creating a software copy of the standard immobilizer chip). However, this program is more complex and, being intended for branded installation centers, will require registration. The simplest registration without confirming your work with an official Pandora partner is possible, but...
Connection diagram
Pandora DXL is a complex security system for cars, so qualified specialists must work with them. When connecting the device, you need to take into account installation requirements, safety and the developer’s recommendations.
Diagram and instructions for installing an alarm using the example of DXL 5000:
DXL 5000
Installation is done as follows:
- Removing the car's panel and steering wheel.
- Installation of the main unit, connecting buses and power.
- Checking the system's functionality.
The installation process is described in general terms, in reality everything is much more complicated and without the appropriate knowledge nothing will work. In addition, you should not trust the installation of the system to unqualified technicians - this can lead to problems with the car alarm or its breakdown, automatic cancellation of the warranty, and even damage to the car.
Key fob with feedback does not respond to button presses
How to set up auto start on a Starline alarm system
On the market of car alarms with two-way communication, Pandora is represented by the following models: DX-70, 90L, 40, DX-90 B, 50B. It happens that the key fob does not open the doors or respond to key presses. Why does this happen?
- The switch is turned off. For three seconds. hold down F.
- The battery has died. Change it.
- The pager froze. Take the battery out of the key fob for a few seconds and insert it. Check the functionality of the device.
- The remote control has become untied from the control unit. Re-write the communicator in the security system memory.
- The machine is parked in an area of active radio interference. Park your car somewhere else.
- Control module failure. Go to the specialists.
Key fob programming
The communicator is entered into the microprocessor unit using the “Valet” service button. To configure the remote control, you need to do the following:
- Disconnect the ignition circuit.
- Turn on the pager.
- Find the service button and press it the required number of times, which will correspond to the PIN code.
When you enter 1 digit, you should wait for the light indication and only then enter the next values. Depending on the signaling model, the programming principle may vary. Thus, the DXL3210, DXL3000 and DXL1870i devices are programmed according to the following instructions:
- Turn off the ignition and press the service button once.
- Hold down the remaining buttons until a sound or light appears.
- Wait for the sound to sound once.
Manual
To configure the Pandora alarm without using computer programs, you need to launch the corresponding option using the “Valet” service button. In most cases, recording and resetting the configuration is carried out by sequentially pressing “Valet” and the ignition key. The designation of all symbols and combination of settings are indicated in the instruction manual.
To link a key fob or remote control, you need to perform the following steps:
- Launch the communicator.
- Turn off the ignition.
- Enter the secret code value by pressing the service button (the number of presses depends on the numbers in the code). After this, the indication should blink red. The steps are repeated for all other values. If the entire code is entered correctly, the key fob will emit 2 light alerts, which will confirm that the programming mode has been activated.
- Next you need to click on “Jack” so that the signal sounds. If you manage to program the system within 20 seconds, the settings will be saved. Otherwise you will have to do everything all over again.
- The next step is to simultaneously press all 3 buttons on the key fob until a sound alert appears.
- When the recording is completed, all that remains is to press the service button again to confirm exiting the programming mode.
Computer
Setting up a Pandora alarm using software is also easy. For this purpose, proprietary software Pandora DXL Loader or Pandora Alarm Studio with an intuitive and comfortable interface is used. By going to the system management menu, you can independently set the necessary settings or diagnose the device for breakdowns.
Instructions for using the program are as follows:
- Connect the device to a personal computer or laptop using a USB cable.
- To configure autorun, you will need to switch option 2-1.1 to “Enabled” (“Allowed”). According to this principle, the start is activated depending on changes in the on-board network voltage or time interval.
- Open group 2-1.1 and select a number of additional settings.
- Save results using the button at the bottom of the screen.
How to bind a remote control with autostart
To register the alarm key fob, you need to make sure that it is turned on and in working order. If numbers appear on the screen when trying to start, the device is in a disabled state. To activate it, just hold down the F key until the third beep sounds.
If after pressing the antenna indication is displayed, the communicator is ready for use. Further actions consist of maintaining a secret code value to open the “Jack” mode. If authorization is successful, a green-red light alert will appear.
It is important for the user to complete programming within 20 seconds so that 1 beep sounds. Otherwise, the operation will fail and will have to be repeated.
After completing the recording, make sure that all communicators are registered in the Pandora system. This is done by removing and reinstalling the battery terminal, after which several audible alerts will sound. Their number will indicate the number of pagers registered in the system.
If there were more signals than key fobs, it means that an additional device is registered in the system. If something goes wrong, you should carefully study the instructions for using the key fob.
Installing a new key fob with GSM function
To register a communicator that supports GSM communication, follow these instructions:
- First of all, you should turn on the Pandora keychain and the mode for changing settings using the “Valet” button.
- Register the Pandora key fob by simultaneously holding 3 pager buttons for 1 second.
- Release the buttons.
- If the actions are completed without errors, 2 alerts will sound from the key fob, and 1 from the control unit.
- Using a similar principle, it is worth registering the remaining communicators.
Installation of car alarms with work algorithm
Security system installation guide:
- The control unit with a microprocessor must be installed hidden in the vehicle interior. For installation, it is recommended to select free space behind the instrument cluster; this will ensure a minimum length of wires when connecting. The installation site must be protected from external influences, including high temperatures and humidity. To further protect the device from vibrations during movement, the module can be wrapped in cellophane. It is recommended to place the unit with the block facing down to eliminate the possibility of liquid drops flowing into the “device” along the wires.
- A transceiver with a built-in antenna is installed on the vehicle window. If the front glass is equipped with a protective film, then to avoid the shielding effect, the transceiver is installed from the rear. The working surface must first be cleaned and degreased.
- The siren is placed under the hood of the car; for installation it is recommended to choose the place most protected from external influences. Do not install the device near the cylinder head or other metal parts adjacent to it. The siren should be placed with the bell facing down to prevent possible moisture accumulation inside in the future. After installation, you must make sure that there is no access to the device and its wires from under the bottom of the vehicle.
- The service button is installed discreetly inside the car. It can be placed under the instrument panel and additionally wrapped with electrical tape to disguise the key.
- Limit switches are installed on the hood, trunk and all doors. The placement of these elements is not allowed in drains or places where moisture accumulates.
- The temperature controller is installed under the hood of the car. To place it, you should select one of the cooling system pipes. You can fix the sensor on the cylinder head or other metal surface adjacent to it.
- Shock and tilt sensors are installed hidden inside the car. During installation, it must be taken into account that the consumer must always have free access to device regulators.
VALET button
The Pandora alarm system with auto-start allows you to disable the security mode using the “Valet” service button:
- Using the key, the first digit of the personal code is entered. The number of clicks must correspond to the sign.
- The next three characters are entered in the same way.
- If the password is entered correctly, the LED indicator will start blinking red and green. The security mode should be disabled.
The protection can be turned on using the service button, but the ignition must be turned off. The key is pressed and held for three seconds. Over the next 30 seconds, the user must exit the vehicle and close all doors. After thirty seconds, the security mode will be activated.
How to use the alarm (step by step instructions)
Before using the alarm, the manual recommends:
- study the instructions;
- install the device;
- study the key fob and the purpose of its buttons;
- Perform programming of the key fob and remote control.
Only after completing the above points can you begin to fully use the security system.
Control key fob
With its help, almost all available functions are activated and deactivated. This is realized by pressing certain buttons or their combinations.
Designation of symbols and buttons on the key fob
Most often, the main feedback control key fob is equipped with five keys and a liquid crystal display. Which buttons do what and their combinations are described in detail in the operating instructions.
For example, the Pandora DXL5000 buttons perform the following functions:
- activation of security;
- alarm deactivation;
- switching between modes and disabling the “Panic” mode;
- state of the system;
- special SOS button.
Pandora DXL5000
The Pandora DX50 liquid crystal display has many icons, the designation of which can be seen in the instructions.
Key fob programming
The key fob is recorded in the control unit using the “Valet” service button.
Principles of setting up autorun
Pandora security systems allow you to configure automatic engine start via CAN in two ways:
- by timer; - by temperature.
Settings are carried out from the key fob by pressing buttons.
By timer
In this case, in order to automatically start the car engine at a certain time, you need to follow the following sequence of steps:
- Hold down the power button “F” and press until you reach the “fan” icon.
- By briefly pressing the shutdown button, you need to enter the autorun settings mode.
- Select the desired menu using F.
- The on and off buttons are used to set the setting start time, daily timer and warm-up time.
- Scroll to the end of the list of possible settings and confirm the changes.
Autorun by timer has been successfully configured. Notifications about engine starting and stopping will be sent to the pager.
By temperature
It is possible to activate engine start based on temperature only if the security system is equipped with an appropriate sensor.
The action algorithm is similar to the setting for triggering by timer:
- Press F and go to the “fan”.
- Use the shutdown button to enter the autorun settings and use “F” to click on the desired menu.
- Use the on and off keys to set the start and stop temperatures when specific values are reached.
- Scroll to the bottom of the menu and confirm changes.
By time
To enable automatic start by timer, you need to do the following:
- While holding down the power button “F”, activate the option with fan indication.
- By briefly pressing the deactivation button, start the automatic start settings mode.
- Enable the desired function using “F”.
- Using the on and off buttons, select the time interval, warm-up duration and other timer parameters.
- Find the item to confirm and save settings.
Table: commands for controlling the system by phone
To control the alarm from a phone, the user must make a call to the system number and enter one of the commands through a mobile device:
| Team | Description |
| # | Return to previous menu or state |
| * | Command to repeat the last message played by the system |
| 1* | Enabling car security mode |
| 0* | Disabling the machine's protective function |
| 9* | Reference |
| 09* | Entering the event history listening menu |
| 007* | Activating the microphone for listening to the interior |
| 100* | Requesting the balance of the SIM card installed in the module |
| 500* | Command to send current vehicle coordinates |
| 258* | Obtaining data on alarm operation |
| 123* | Command to remotely start or extend the operation of the power unit |
| 321* | Stopping the engine started in autostart mode |
| 156* | Activation of the pre-heater |
| 651* | Disabling the pre-heater |
| 456* | Activation of an additional communication channel |
| 654* | Disabling additional channel |
| 789* | Command to enable automatic start of the power unit |
| 987* | Command to enable engine auto-start prohibition |
| 666* | Motor lock |
| 999* | Disabling the engine immobilizer |
Why is there no connection between the remote control and the module?
Often, when using the Pandora anti-theft complex (1870i, 3110, 3700, 3100, 3500, 3210, 5100 New, 3900, 1000), the connection between the switch and the system is lost. The following will provide instructions for correcting the causes of alarm failure:
- The battery in the key fob is dead. Install a new one;
- exposure to external radio interference. Park the car in a different location. Check the operation of the alarm;
- The keychain is broken. Repair it yourself or replace it with a new one;
- The control module has failed. Go to an electrician;
- dead battery. Charge it or install a new one.
PROMOTION: SALE OF NEW CAR 2022 PRODUCTION
How to start with key fob
Remote engine starting is possible only if several prerequisites are met. This is necessary in order to prevent unauthorized access to control the vehicle and minimize the likelihood of theft.
You can start the engine using the Pandora car alarm remote control under the following conditions:
- the security system is switched to security mode;
- handbrake is on;
- the lever is in “P” mode.
In all other cases, it will be impossible to start the engine from the key fob.
When using an automatic or manual transmission, the process of turning on the engine will be approximately the same. The vehicle owner's task is to:
- On the control panel, press the key with the image of a closed lock and hold it for 3 seconds.
- The key fob will emit 3 loud beeps, which will indicate the start of the engine.
- A flashing fan icon and a crossed out icon of the switched off shock sensor will appear on the remote control display.
- After a few seconds, the security system will start the engine.
- When the engine is started, an image of a rotating fan will appear on the screen.
- The device will notify you of the completion of the process with a long beep.
How to disable the feature
Disabling autorun is carried out according to the recommendations contained in the operating manual. You need to enter the menu by pressing the F button and clicking on the fan icon. To deactivate the daily timer, you need to switch the function to the inactive St Of mode by clicking on the “Off” button. When you disable temperature triggering, you should go to menu item 3 by pressing the F button twice more. The option is switched to Sº Of mode.
Disabling periodic heating is done in menu item 6, which can be accessed by pressing the F key three times.
Here the checkbox is set to Sd Of mode. To completely disable the autorun function, you need to press the F button and the fan icon (for a few seconds). In the window that appears, select the key with the image of a closed lock. The system will reset all previously set settings.
Troubleshooting
Autorun may not work well for the following reasons:
- the mode is set incorrectly;
- no handbrake control;
- The battery is dead.
To properly configure autostart from your communicator, it is recommended to turn off the car and arm it for 5 seconds. Then press the security mode activation key three times. The engine will start. The actions are repeated and the engine stalls. Now you can program the remote start of the power plant based on temperature and timer.
If autostart based on temperature does not work, the reasons may be different. You need to carefully check all settings. The engine temperature sensor may be faulty. Some models will require a firmware update to restore automatic startup. The cause of the problem may be oxidation of the contacts. In case of major problems, it is recommended to contact a service center.
- Phone alarm for car
- How to enable autorun
- How to set up a Pandora alarm
- Alarm Pandora key fob operating instructions
Identification of symbols and buttons
If we consider the Pandora DXL model, the key fob will have 5 buttons and an informative LCD monitor, where symbols of basic functions are indicated. To understand what these icons mean, you need to study each icon separately and become familiar with the indications.
On the DXL5000 signaling the buttons are designed for the following tasks:
- Enabling security functions.
- Disabling security.
- Switching modes and deactivating the “Panic” option.
- Checking the status.
- Emergency call.
There are a large number of icons on the LCD screen. Their designation is indicated in the operating instructions.
Table: model range and advantages of Pandora alarms
Description of the main advantages characteristic of individual versions of Pandora alarms:
| Model name | Description of features |
| Pandora DX50 | List of benefits:
|
| Pandora 3000 | List of the main advantages of security systems 3000:
|
| Pandora 3210 and 3210i | The main advantages of these versions of Pandora alarms:
|
| Pandora 3500 | Advantages characteristic of these models:
|
| Pandora 5000S | Advantages of these models:
|
Sources
- https://remontautomobilya.ru/signalizaciya-pandora-instrukcii-po-ekspluatacii-ko-vsem-modelyam.html
- https://bezopasnik.info/%D1%81%D0%B8%D0%B3%D0%BD%D0%B0%D0%BB%D0%B8%D0%B7%D0%B0%D1%86%D0 %B8%D0%B8-pandora-%D1%81-%D0%B0%D0%B2%D1%82%D0%BE%D0%B7%D0%B0%D0%BF%D1%83%D1%81 %D0%BA%D0%BE%D0%BC-%D0%BA%D0%B0%D0%BA-%D0%BD%D0%B0%D1%81/
- https://remont-avtovaz.ru/obzor-avtosignalizatsij-pandora-serii-dxl/
- https://AutoTuning.expert/avtosignalizatsiya/pandora-instruktsiya-po-ekspluatatsii-brelka.html
- https://autodvig.com/alert/signalizatsiya-pandora-s-avtozapuskom-82363/
- https://avtomaster-ekspert.ru/signalka/pandora-kak-zavesti-s-brelka.html
- https://AutoTuning.expert/avtosignalizatsiya/pandora-s-avtozapuskom.html
Table: causes and methods of eliminating autorun not working
If the remote starting of the motor does not work or difficulties arise in the operation of the option, it is necessary to determine the reason:
| Problem | Corrective Actions |
| Low battery in remote control | The battery changes:
|
| Failure of the key fob | You can fix the problem yourself only if the defect is not serious:
|
| Incorrect installation of system elements | You need to make sure that all components are installed correctly. The antenna module must be fixed on the glass as high as possible to ensure high-quality signal transmission. The temperature sensor must be mounted directly to the engine or adjacent components. If necessary, the controller is reinstalled. A possible reason may be that the locking relay is connected incorrectly; you need to check the quality of the connection. |
| Conflict between the standard immobilizer and the alarm blocker | To fix this problem, there are two ways:
|
| Malfunction of the components of the ignition system | To fix the problem, you need to diagnose and replace damaged components, meaning:
|
| Lack of preparation of the car for autostart | To fix the problem, you need to configure the “Software Neutral” option |
| Service mode enabled | This feature must be disabled |
| Damage to alarm wires | To resolve the problem, follow these steps:
|
| Low battery | When the mains voltage drops, the battery may not have enough capacity to start the engine. You need to visually check the battery. If there are cracks on its body, the device is replaced with a new one. The battery voltage is also diagnosed using a multimeter. With the engine turned off, the operating parameter should be about 12.5-13 volts, and on a car with the engine running - about 13.4 V. |
IMPORT SUBSTITUTION NOT IN WORDS, BUT IN ACTION!
This is the “correct” and patriotic import substitution from Kaluga that happened. We don’t buy imported goods, save money, and improve the consumer properties of the product at the same time! And at the same time we work for the benefit of our country. More such import substitution!
Of course, our engineers continue to work on bypass algorithms and soon owners of other popular cars in Russia will also have the opportunity to save money when installing a car alarm with automatic engine start, while simultaneously receiving unrivaled service from the technological market leader - Pandora.
RUSSIAN RESPONSE FROM PANDORA
This was probably the most compelling reason for us to introduce these functions into our car alarms for FREE. Now there is no reason to spend money on imported modules for algorithmic bypass of built-in immobilizers. Of course, while we are able to bypass the immobilizers of not all cars that Canadians “bypass”; but today there are already more than a hundred popular brands in Russia - more than 80% of modern cars on our market.
We have been doing this for a short time – a little over a year, and a team of engineers for this task was formed quite recently. Before this, our engineers worked as linemen “in between jobs.”
We have just completed a series of developments that allows us to bypass immobilizers and start the engines of all modern TOYOTA/LEXUS cars equipped with Start&Stop buttons, which the Canadians knew how to bypass, including the latest cars of 2016. And this is very serious news. Of course, our engineers spent a little more time on this algorithm than on other brands, but still its fairly quick successful implementation speaks of powerful potential.
Military technology to protect a civilian vehicle
The Pandora 5000 alarm system with auto start can be considered the most advanced security system for a car. The maximum degree of vehicle protection is ensured by using a proprietary dialogue code - this encryption technology is used in our country's military aviation. The Pandora 5000 new alarm system cannot be hacked using a code grabber (not a single such case has been recorded), and it is also impossible to “interfere” in the communication process between the units of the complex, since 128-bit AES encryption is used here.
Installation of the Pandora 5000 alarm system will require minimal “disassembly” of the car’s interior trim, since its main units “communicate” with each other via a secure wireless communication channel. The main key fob for the Pandora car alarm deserves special attention - it is equipped with an LCD display, has the ability to set different melodies for each event, allows you to control 12 security zones simultaneously and adjust the sensitivity of the sensors, displays the current temperature and state of the car battery. Naturally, the Pandora alarm system is equipped with instructions for operating the key fob.
The innovative (digital) interface of the Pandora car alarm allows you to connect directly to 2 digital buses of the vehicle. Unlike previous versions of the complex, Pandora 5000 new has a more advanced non-volatile memory unit, and overall power consumption has been kept to a minimum. This complex has a built-in GSM module and the ability to integrate into the GLONASS/GPS receiver system. Installing a Pandora alarm system allows you to control online car parameters such as:
- its location;
- cabin temperature;
- power system parameters;
- turn on wiretapping in the cabin;
- track the locations and number of refills.
Despite the presence of a convenient key fob in the Pandora DXL 5000 alarm system, you can control the entire system via a smartphone; just install a specially designed mobile application on it, which can be downloaded on the official website for iOS and Android devices, and you can watch the process of managing the system in the video:
In addition to the fact that control of the Pandora alarm system via a smartphone has no range restrictions, it will be indispensable if it turns out that the key fob does not work (for example, the battery is dead). The mobile phone screen displays all current information about the car’s condition, and the owner can issue absolutely any supported commands, for example, remotely start the engine or turn on the air conditioning. This security system comes standard with two additional immobilizer tags, which allow you to unlock the car in Hands Free mode. Their use will prevent a situation where the driver is simply thrown out of a running car - the tag remains with him, and the car's immobilizer, having stopped receiving a signal from it, will simply block the engine.
- The ideal option for car protection is a combined anti-theft system.
- Individual theft protection for each car
- Advantages of modern car alarms
- What to consider when installing a GSM alarm
Alarm for those who don't need a key fob
Practice shows that the Pandora alarm system, installed in accordance with the operating instructions, is suitable for any car - both domestic and imported. One of the most budget-friendly is the Pandora 3910 alarm system, which, nevertheless, provides a high level of vehicle protection. This version of the security complex has several control options:
- car owner's smartphone;
- special immobilizer tags;
- separate Internet service;
- standard vehicle key.
The fact that there is no control key fob in the Pandora 3910 alarm system, according to reviews from car owners, does not limit the functionality of the system at all, and allows you to get rid of a fairly large “add-on” that you will need to constantly carry with you.
A smartphone, which almost every person keeps with them at all times, in this case will be an almost ideal alarm control device. The undoubted advantage of such a “remote control” is the fact that you can control an abandoned car from any distance from it. Using a smartphone, it is easy to control the temperature of the engine or interior, receive real-time information about the voltage value in the on-board network, send commands to autostart or turn on the preheater. In addition, you can additionally install a GPS module, which will make it possible to always have the exact coordinates of your car.
The control process can be carried out either by making calls to the system number, or by installing a special mobile application on your smartphone, available for iOS and Android platforms. The Pandora 3910 alarm system can be installed on any car. If there is a digital bus, this can be done using a CAN or 2CAN bus, and if there is no “digital”, the alarm can be installed analogue. The presence in this modification of special tags, which must be constantly with the driver, allow the immobilizer to recognize “its own” and not block the car’s engine.
How to enter system programming mode?
Self-programming of the Pandora 3910 alarm system by car owners is not approved by the manufacturer, since this procedure is quite complicated and can make serious changes to the factory configuration.
Programming can be done in several ways:
- using the Valet service mode key;
- via laptop and software;
- using a smartphone on which you must first install a mobile application.
To use the service button, the car owner must know the password. Initially, the complex is assigned code 1111. To program the system, open the doors and press the Jack key four times, between each click you must pause for one second. When you press the buttons quickly, the complex will perceive these actions as a double or triple click. When each digit of the password is entered correctly, the LED indicator will blink once. If the light blinks four times, this indicates successful entry into the setup mode.
If you want to use a computer for setup, you must first download the DXL Loader application onto it. The laptop is connected to the system via a mini-USB cable. After starting the software, a password is entered to enter programming mode. After programming, you just need to turn off the ignition, this will save the configuration.
User BaronKorf spoke about the features of the mobile application, as well as the web monitoring resource from Pandora.
Distinctive parameters of dx50 and dx50b
Pandora line 50 anti-theft systems are developed based on the same technologies and solutions. The main differences are in the configuration, but they are not significant. DX50b models come with a redesigned main communicator.
Pandora DX-50 B, initially has a low price, allows the car owner to save money when connecting an autostart, since there is no need to give away one of the standard keys or order a duplicate of it. The new LCD key fob D-078 is similar in appearance to its predecessor, but has a black body and is more economical and has a more informative screen.
New in the DX-50 B LCD:
- separate door indications are displayed, as on the flagship Pandora models;
- there is an icon for the preheater operation;
- a convenient system of widgets that help you quickly assess the current state of the car and alarm system.
Keychain Pandora DX-50 B
Description and equipment
The Pandora DXL Pro car alarm is a premium anti-theft system. It is designed specifically for installation on class B, C, D machines
Alarm equipment with auto start:
- A set of wires that will ensure the connection of all modules and devices of the complex.
- LED indicator. It shows the status of the car alarm.
- Temperature sensor. With its help, you can connect and configure the option of automatically starting the motor based on temperature.
- Valet security service mode button. After its activation, the system will operate in an emergency state. This will allow you to turn off the alarm and configure the key fobs.
- USB cable for connection.
- Tags designed to identify the car owner.
- Auxiliary controller plug with wiring.
- A case for installing tags in it.
- Limit switch.
- A special block designed to implement the autorun option.
- GSM module.
- Microphone used to listen to the interior.
- A set of ties for combining and fixing electrical circuits.
- Main and additional remote control.
- User's manual for installation and operation of the complex.
The Stal63 channel reviewed the operation of the security system on the Toyota Camry.
Why doesn't autorun work?
There are a fairly large number of problems with car alarms that can be eliminated, for example, by simply turning off the power.
Causes
Most often, the engine will not start automatically for the following reasons:
- incorrect setting;
- controller software failure;
- failure of the control unit;
- temperature sensor failure.
How to fix?
To get rid of difficulties with automatic starting yourself, you need to:
- Correctly adjust the mode and set the intervals between starts.
- Check whether autorun is prohibited by the system.
- Make sure the temperature sensor is working properly.
- Reboot the system by disconnecting the battery for 30 minutes.
- Send the control unit to a service center for diagnostics.
The Pandora DXL system allows the owner to set automatic engine start and stop modes to warm up the engine and vehicle interior, charge the battery, prepare the vehicle for intense driving, or to cool the vehicle interior with air conditioning. The synchronized real-time clock of the key fob and the base unit of the system, and other autonomous system settings make it possible to implement many conditions for starting and operating the engine, regardless of whether the key fob is in the operational zone of the command radio channel or not. Programming of automatic start modes and engine operating conditions is carried out on a key fob with an LCD display. To program these modes, you need to quickly press the button
select the icon, press the button and go to the automatic start functions menu. The menu has eight sublevels, which can be moved between by pressing the button. Changing the sublevel value is done using the and buttons.
When changing the values of functions for their execution by the system, before exiting the menu, you must save their value by pressing the button
go to the “Send” sublevel and click the button to save or the button to cancel the changes made. The results of the changes will be transmitted to the base unit of the system, which will be confirmed by a short double beep from the key fob.
NOTE: If you do not press the or button, the engine operation settings in the remote and automatic engine start modes will remain the same.
To go to the next engine settings parameter, briefly press the button
.
To exit the engine operation setup mode at any time, press and hold the button
for 1 sec. (or exit will occur automatically after 10 seconds), but all settings changes made will not be saved.
Automatic engine start at a set time (daily timer)
The mode allows you to start the engine according to the set daily time and will operate if the mode is turned on in the key fob settings (START menu) and the start time is set.
In this case, the launch will be repeated for 5, 7, 14 days or an unlimited number of times (set programmatically in the system programming menu), regardless of the number of security cycles during this time, after which the mode is automatically deactivated.
Automatic engine start based on engine temperature
The mode allows you to automatically start the engine based on its temperature and will operate if the mode is turned on in the key fob settings (START menu) and the start temperature is set.
Setting the engine warm-up time for automatic or remote engine start
The engine warm-up time limit is set in the “START” menu of the key fob within the range of 0 – 60 minutes. It must be borne in mind that if the condition of stopping the engine upon reaching the set temperature is also activated, then the engine will stop if an earlier event occurs. The maximum warm-up time can be limited (Adjustable in the system programming menu. Factory default is 30 minutes).
