The coolant light is on VAZ 2114 injector 8 valves

Coolant level sensor for VAZ 2114: device, check and replacement

Probably every experienced owner of the fourteenth model has encountered a yellow icon in the form of a cup with a scale burning in the signal lamp block.
This is the coolant light on the VAZ 2114. This article is dedicated to those who encountered this problem for the first time and those who have already solved it. The on-board control system warning lamp unit is located to the driver's right above the central ventilation system nozzles.

It is a narrow plastic panel with seven indicators:

1. - little oil;
2. -insufficient level of windshield washer fluid;
3. -low coolant level;
4. -one of the doors is unlocked;
5. - there is a malfunction of the brake lights and dimensions;
6. - pad wear;
7. -belts are not fastened.

You saw the light on and, first of all, checked the fluid level in the expansion tank (usually it can be seen through it). On a cold engine, the antifreeze is located exactly between the minimum and maximum marks, and the light is still on. This indicates that the VAZ 2114 coolant level sensor is not working.

INDICATOR BUGS

Also, the instrument panel on the VAZ 2114 has a block of light indicators, which includes the following icons:

Indicators

Let's look at the designation of the icons on the instrument panel in more detail:

1. An indicator that displays information about the current engine oil level. When the amount of lubricating fluid is critically low, the light turns orange. Oil must be added immediately after this indicator becomes active;
2. This indicator indicates a low amount of working fluid in the windshield washer reservoir. The tank is designed for 5 liters of liquid, the indicator turns on when its quantity drops below 1 liter;
3. Fluid quantity sensor in the engine cooling system. One of the most important indicators that needs to be closely monitored;
4. Indicates the presence of unlocked doors. Lights up red;
5. An indicator that lights up if the dimensions or brake lights are out of order. The active indicator color is red;
6. A light that lights up in case of critical wear of the brake pads (1.5 mm). Lights up from the moment you first press the brakes until the car is turned off;
7. An indicator indicating that the driver is not wearing seat belts.

An exclamation mark on the instrument panel of a VAZ 2114 can light up in two cases: when the car’s starter is turned on, and when the brake fluid level is low. As a rule, the reason is in the second option.

To eliminate the problem, completely fill the tank and check the contacts of the TZ level sensor, which are located on the container lid, for oxidation.

If the engine icon on the panel is on, it means something is wrong with the power unit of the fourteenth. There are many reasons why the Check Engine light comes on; it often stays on even when there are no visible faults. It is best to go to a service station for diagnostics, this way you will be protected from possible problems.

Replacing the coolant level sensor

Unfortunately, plastic sensors often break, and it even happens that newly installed new elements fail. This is a sore spot of the VAZ 2114, so in subsequent models (such as Granta, Priora) they were completely removed. You can do the same.

To no longer deal with broken sensors, buy a new expansion tank with only a cap and install it in place of yours. And you either remove the wires from the mounting block chip, or simply insulate them and leave them as is.

1. Go to the store and buy a VAZ 2114 coolant level sensor (90 rubles).
2. Disconnect the terminal from the battery.
3. Remove the block from the old sensor.
4. Unscrew it from the tank.
5. Screw in a new one.
6. Connect the block and place the terminal on the battery.

Installation

Install the new sensor in reverse order.

Such a simple component of the cooling system as the VAZ 2114 expansion tank can cause a lot of trouble for the motorist. Let's look at which ones exactly to be in the know. There are not very many major problems, but the price of repairs may differ, and significantly. The most common breakdown is rubbing of the tank body. A small hole appears through which liquid seeps out. But there are more serious problems.

Coolant level sensor repair

If the sensor contacts are intact, but the sensor itself does not function as it should, then it can be repaired.

1. Remove the sensor from the car.
2. Remove the amendments.
3. Using sealant, glue it well to the body.
4. Then solder the joint (isolate it from antifreeze).

This way you can repair the plastic float. The porous float must be replaced, however, you can find a similar part and install it in its place.

Source

How is the coolant level sensor connected to the VAZ 2114?

Some VAZ 2114 vehicles were equipped with a coolant level sensor (antifreeze, antifreeze).

It is located in the expansion tank of the engine cooling system and sends signals to the driver (through a lamp in the display unit) that it is time to add coolant, because the level has dropped. Here is the connection diagram for this sensor with its description of the elements and operating procedure.

Connection diagram for the coolant level sensor for a VAZ 2114 car

Description of the coolant level sensor connection diagram

— On a VAZ 2114 car, the coolant level sensor is built into the gap in the negative wire of the low coolant level warning lamp in the expansion tank of the engine cooling system.

— Plus (voltage) is supplied to the warning lamp in the display unit of the on-board control system of the front panel of the vehicle. After turning the key in the ignition.

Execution Sequence

2. Disconnect the wiring harness block from the sensor.

3. Using a piece of wire or a metal clip, we close the terminals of the connecting block. If the warning lamp for insufficient coolant level comes on, the sensor is faulty. If the lamp does not light, then with the ignition on, use a voltmeter to measure the voltage at the terminals of the connecting block. The voltage should be about 12 V. If voltage does not flow to the block, then there may be poor contact or a broken wire in the sensor circuit or the light indication unit is faulty.

4. Unscrew the sensor cover. Remove the sensor float from the tank and remove the sensor.

5. Connect the multimeter (in ohmmeter mode) to the sensor terminals.

6. By moving the float from one extreme position to another, we monitor the readings of the device. The electrical resistance of a working sensor in the upper position of the float should be infinitely large, and in others it should be close to zero.

Recommendation: Oxidized leads in the block should be cleaned with an awl or a thin file. Damaged sections of wires must be repaired. The faulty sensor and display unit are replaced (see “On-board monitoring system display unit - removal and installation”).

The light on the panel of the VAZ 2114 came on - who knows?

Who knows what kind of light came on on the central panel of the VAZ 2114, not where the odometer is, there is an oil light there of course, but on the central panel?

What does this mean, how scary is it and is it possible to drive like this?

Urgent car purchase and car pawnshop

Who knows what kind of light came on on the central panel of the VAZ 2114, not where the odometer is, there is an oil light there of course, but on the central panel?

What does this mean, how scary is it and is it possible to drive like this?

Low oil level light. Check the level on the dipstick - if it’s normal, then most likely the sensor is just messing around. If it doesn't bother you, drive like this.

Probably every experienced owner of the fourteenth model has encountered a yellow icon in the form of a cup with a scale burning in the signal lamp block. This is the coolant light on the VAZ 2114. This article is dedicated to those who encountered this problem for the first time and those who have already solved it.

The on-board control system warning lamp unit is located to the driver's right above the central ventilation system nozzles.

It is a narrow plastic panel with seven indicators:

1. - little oil;
2. -insufficient level of windshield washer fluid;
3. -low coolant level;
4. -one of the doors is unlocked;
5. - there is a malfunction of the brake lights and dimensions;
6. - pad wear;
7. -belts are not fastened.

You saw the light on and, first of all, checked the fluid level in the expansion tank (usually it can be seen through it). On a cold engine, the antifreeze is located exactly between the minimum and maximum marks, and the light is still on. This indicates that the VAZ 2114 coolant level sensor is not working.

Preventing problems in the cooling system

Many problems can be prevented if the right preventive measures are taken. For long and stable operation of the cooling system, it is recommended:

1. Use only high-quality branded antifreeze that is suitable for your car. You can find out the recommended parameters in the official operating instructions.
2. Do not mix several coolants with different chemical compositions, even if they are the same color.
3. Change the coolant promptly before it loses its properties.
4. Monitor the level in the tank and do not allow it to drop or rise excessively.
5. When replacing old antifreeze with a new one, flush the system with clean water or special chemicals.

How to check the coolant level sensor on a VAZ 2114

1. Disconnect the electrical connector (latch) from the sensor.
2. Unscrew the sensor from the tank.
3. Close both terminals of the sensor into an electrical circuit with a 12 V current source and a control light.
4. When the float is lowered down, the light should be on, when raised up it should go out.

If the “control” showed that the reed switch sensor is faulty, then there are three possible options for resolving the situation.

Replacing the coolant level sensor

Unfortunately, plastic sensors often break, and it even happens that newly installed new elements fail. This is a sore spot of the VAZ 2114, so in subsequent models (such as Granta, Priora) they were completely removed. You can do the same.

To no longer deal with broken sensors, buy a new expansion tank with only a cap and install it in place of yours. And you either remove the wires from the mounting block chip, or simply insulate them and leave them as is.

1. Go to the store and buy a VAZ 2114 coolant level sensor (90 rubles).
2. Disconnect the terminal from the battery.
3. Remove the block from the old sensor.
4. Unscrew it from the tank.
5. Screw in a new one.
6. Connect the block and place the terminal on the battery.

Signs of trouble

Typical symptoms of DTOZ failure are as follows:

• Turning on the fan when the engine is not warmed up;
• A warm engine does not start well;
• Unstable engine speed at idle;
• Unstable engine operation (triggering, lack of traction)
• Gasoline consumption increases;

If the DTUOZH fails, the engine runs stably, without interruptions, but on the dashboard you see that the liquid does not heat up or does not cool down at all. These are all signs of a faulty DTOZH on a VAZ 2114.

Coolant level sensor repair

If the sensor contacts are intact, but the sensor itself does not function as it should, then it can be repaired.

1. Remove the sensor from the car.
2. Remove the amendments.
3. Using sealant, glue it well to the body.
4. Then solder the joint (isolate it from antifreeze).

This way you can repair the plastic float. The porous float must be replaced, however, you can find a similar part and install it in its place.

1) Good afternoon! VAZ 2114 2013, lately the high coolant temperature sensor (which is yellow) has been lighting up, I can’t understand why, the on-board driver writes that the temperature is normal, the fan turns on. What could be the reason? . 2) Hello everyone, please tell me why maybe you are driving 80 km, everything works fine, you give gas and the VAZ 2109 carb starts to twitch. Write the number of the question you are answering! The coolant sensor on the VAZ 2114 is on.

Similar articles

11 comments on “The coolant sensor on the VAZ 2114 is on. Lately the high coolant temperature sensor has been on.”

1... maybe this is a low fluid level sensor?...

2 clean the carb, or you will change the fuel pump, change the fuel filter.

Andrey, I have antifreeze and it’s normal, everything is at the level. When this light is on, does it mean there is low antifreeze?

1) this is not a high temperature sensor, but a low coolant level sensor

Share...

1 it gets dull for every second one, like the rest of the sensors

1) I agree with Alexey, he either fucks up or doesn’t work

1 unscrew the sensor in the expansion tank and clean the leg on which the float runs. You can also glue a piece of foam or other material that will easily float to the float

2. Clean the carb. Or maybe the accelerator is dead.

1) To start delivery, see if the rod is worn out, then check the fuel pump and then get into the carb.

Source

Possible breakdowns of DTOZH

We will name the most common malfunctions that are associated with malfunctions in the operation of the device: contact failures or breaks in which insulation is lost, the fan does not function as required.

Signs of failure include the following:

• When the engine is not warmed up, the fan starts to work;
• The engine is warm enough, but its performance can be considered unsatisfactory;
• Excessive fuel consumption is observed.

Among the common erroneous beliefs, there is one: young and inexperienced motorists do not see the difference between two concepts: DTOZH and coolant temperature indicator sensor.

The light on the panel of the VAZ 2114 came on - who knows?

Who knows what kind of light came on on the central panel of the VAZ 2114, not where the odometer is, there is an oil light there of course, but on the central panel?

What does this mean, how scary is it and is it possible to drive like this?

Urgent car purchase and car pawnshop

Who knows what kind of light came on on the central panel of the VAZ 2114, not where the odometer is, there is an oil light there of course, but on the central panel?

What does this mean, how scary is it and is it possible to drive like this?

Low oil level light. Check the level on the dipstick - if it’s normal, then most likely the sensor is just messing around. If it doesn't bother you, drive like this.

Probably every experienced owner of the fourteenth model has encountered a yellow icon in the form of a cup with a scale burning in the signal lamp block. This is the coolant light on the VAZ 2114. This article is dedicated to those who encountered this problem for the first time and those who have already solved it.

The on-board control system warning lamp unit is located to the driver's right above the central ventilation system nozzles.

It is a narrow plastic panel with seven indicators:

1. - little oil;
2. -insufficient level of windshield washer fluid;
3. -low coolant level;
4. -one of the doors is unlocked;
5. - there is a malfunction of the brake lights and dimensions;
6. - pad wear;
7. -belts are not fastened.

What you need to know about DDM?

If the indicator lights up indicating low oil pressure, this does not always mean that there is not enough lubrication in the system. It is possible that the DDM is faulty. In order to find the true cause, you need to know what the device is and how it can be checked.

Purpose and location

The DDM consists of a housing, a membrane and a transmitting device. The membrane becomes deformed when oil begins to press on it. Deformation of the membrane is reflected in the rheostat, whose resistance changes. The ECU records changes and reflects them thanks to an indicator on the instrument panel. The controller on the VAZ 2109 is located under the oil filter on the cylinder head on the side where the carburetor is located.

DDM location

Diagnostic features

Before diagnosing the DDM, you should check the oil level in the system using a special dipstick and an oil filter.

One of the simplest diagnostic methods is to check the presence of pressure in the lubrication system. To do this, you need to unscrew the DDM from the socket and manually turn the crankshaft several times. If grease flows or splashes out of the socket and the control light remains on, this means that the pressure is OK and the cause of the malfunction is in the controller.

The process of unscrewing the DDM from the socket

Next, you should visually inspect the device itself. If no mechanical damage is detected, it must be cleaned with gasoline and screwed into the old place. If after this the light does not go out, this indicates that the device is broken and must be replaced.

For the second method of checking, a pressure gauge is required. The controller is removed from the warm engine and screwed into the pressure gauge; the adapter from the pressure gauge is screwed into its place. The control LED is connected to the positive terminal of the battery and the controller contacts. Then the running engine should gradually pick up speed until the pressure gauge shows a value of 1.2-1.6 bar. If the controller is working properly, the LED will go out. Otherwise the device is faulty.

Replacement instructions

To replace the DDM with a VAZ 2109, you will only need one key for “21” and a new device (the author of the video is Avto_Remont).

The procedure consists of a sequence of steps:

1. You need to start work by disconnecting the negative terminal of the battery.
2. Next, you need to disconnect the supply wire from the lubricant pressure controller.
3. Then use the key to “21” to unscrew the faulty device.
4. For sealing, aluminum foil in the shape of a ring is placed in the sensor socket.
5. Now the new device is screwed in.
6. All that remains is to connect the wire, and this completes the procedure.

Thus, there is nothing complicated in replacing; more time is spent on diagnostics.

How to check the coolant level sensor on a VAZ 2114

1. Disconnect the electrical connector (latch) from the sensor.
2. Unscrew the sensor from the tank.
3. Close both terminals of the sensor into an electrical circuit with a 12 V current source and a control light.
4. When the float is lowered down, the light should be on, when raised up it should go out.

If the “control” showed that the reed switch sensor is faulty, then there are three possible options for resolving the situation.

Replacing the coolant level sensor

Unfortunately, plastic sensors often break, and it even happens that newly installed new elements fail. This is a sore spot of the VAZ 2114, so in subsequent models (such as Granta, Priora) they were completely removed. You can do the same.

To no longer deal with broken sensors, buy a new expansion tank with only a cap and install it in place of yours. And you either remove the wires from the mounting block chip, or simply insulate them and leave them as is.

1. Go to the store and buy a VAZ 2114 coolant level sensor (90 rubles).
2. Disconnect the terminal from the battery.
3. Remove the block from the old sensor.
4. Unscrew it from the tank.
5. Screw in a new one.
6. Connect the block and place the terminal on the battery.

Coolant level sensor repair

If the sensor contacts are intact, but the sensor itself does not function as it should, then it can be repaired.

1. Remove the sensor from the car.
2. Remove the amendments.
3. Using sealant, glue it well to the body.
4. Then solder the joint (isolate it from antifreeze).

This way you can repair the plastic float. The porous float must be replaced, however, you can find a similar part and install it in its place.

1) Good afternoon! VAZ 2114 2013, lately the high coolant temperature sensor (which is yellow) has been lighting up, I can’t understand why, the on-board driver writes that the temperature is normal, the fan turns on. What could be the reason? . 2) Hello everyone, please tell me why maybe you are driving 80 km, everything works fine, you give gas and the VAZ 2109 carb starts to twitch. Write the number of the question you are answering! The coolant sensor on the VAZ 2114 is on.

Similar articles

Examination

Today, VAZ 2109 car owners use two methods to check the condition of the coolant temperature sensor. Let's say right away that the second one is more reliable, but the first one is easier. Decide for yourself which of the methods presented below to use.

Verification method

Your actions

According to the table, check whether the resistance corresponds to that required at a particular temperature of coolant or boiling water.

Temperature (in degrees Celsius)

Resistance (Ohm)

If there are deviations from the norm, we conclude that the sensor no longer performs its functions properly and therefore requires mandatory replacement.

Replacement