Replacing the front wheel bearing of a VAZ 2107 “Classic”

Diagnostics - causes and symptoms of malfunction

The condition of a wheel bearing is assessed based on a number of factors. The main signs of a node malfunction include:

1. noticeable wheel play;
2. hum, rustle, crunch from a spinning wheel;
3. the suspended axis rotates unevenly, there is wedging;
4. excessive heating of the disk;
5. increased noise when cornering.

The main reason for replacing a wheel bearing is due to normal wear and tear. The gap increases and eventually stops responding to adjustment.

How to check the wheel bearing of a VAZ-2107:

How to determine front wheel bearing wear:

Other causes of failure:

1. wheel impacts;
2. technological violations during the previous replacement;
3. entry of foreign particles into the separator cavity (dust, dirt, metal shavings);
4. aggressive driving style.

If at least one malfunction is detected, it is necessary to replace the parts. Continued operation of the vehicle is dangerous.

Steering knuckle on the VAZ 2107: what is it for?

Even the uninitiated can answer what a steering knuckle is: obviously, it is a mechanism that ensures the wheels turn while driving. The steering knuckle secures the hub elements of the front row of wheels on the VAZ 2107 and is mounted on the upper and lower suspension arms.

As soon as the driver begins to turn the steering wheel in the cabin, the gear lever acts on the steering rods, which, in turn, pull the steering knuckle to the left or right. This ensures that the front wheels turn in one direction or another.

The main purpose of the steering knuckle in the design of the VAZ 2107 is to quickly and without failure ensure that the front pair of wheels turns in the direction desired by the driver.

Steering knuckle device

The mechanism itself is made of high-strength cast iron, and therefore has a long service life. According to the designers, this unit should withstand serious loads and not “wedge” at the most crucial moment. It is worth emphasizing that on the VAZ 2107 the steering knuckle is indeed one of the most reliable elements: most drivers never change it throughout the entire period of operation of the car.

The design of the front suspension of the “seven” uses two steering knuckles at once - left and right. Accordingly, the elements have slight differences in fasteners, but in other respects they are completely identical:

• manufacturer - AvtoVAZ;
• weight - 1578 g;
• length - 200 mm;
• width - 145 mm;
• height - 90 mm.

The main elements of the steering knuckle are:

1. The axle is the part of the axle on which the bearing is located. That is, the axle serves as a support for the rotational movement of the wheels.
2. The kingpin is the pivot rod of the swivel joint.
3. A wheel rotation limiter is a device that prevents the fist from turning to its maximum due to the risk of loss of control.

Design of the unit being repaired

The VAZ 2107 hub consists of the following elements:

The diagram shows:

1 — steering fist; 2 — hub seal; 3 — remote ring of the front wheel hub oil seal; 4.5 — hub bearing; 6 — washer 2101; 7 — nut M18x1.5 left; 8 — hub cap.

All parts are located inside the hub housing.

Front-wheel drive features

For example, let’s take two cars – a “nine” and a “ten”. Let's first study the procedure for changing the bearing on the rear hub on a VAZ 2109 car. Breakage of our part in this car can occur due to the following factors.

1. Reckless driving with constant sharp braking and acceleration.
2. End of service life, shortened due to bad roads.
3. Violation of the integrity of the oil seal.

Diagnostics is carried out according to the well-known principle: you need to shake the wheel. We list the tools and supplies needed for repairs in the following list:

• wrenches;
• hammer, round timber, wooden block;
• puller;
• Litol lubricant.

1. Using wrenches, remove the wheel nuts and the central hub nut.
2. We lift part of the car on a jack and remove the wheel (here there is no need to hang up the entire half of the car).
3. The handbrake must not be applied!
4. We twist the pins of the brake drum and dismantle it, you can use a hammer and a block.
5. Unscrew the hub nut and tighten the hub with a puller.
6. If the inner ring of our replacement part remains on the suspension axle, we pull it off using a puller.
7. We take the removed assembly, remove the retaining ring, and use a round timber and a hammer to knock out the broken part.
8. After applying lubricant, we press in new parts.
9. We do the assembly by moving point by point backwards.

Now, if we compare the two instructions we have given, it turns out that the presence or absence of a wheel drive under the trunk has little effect on the number of stages, as well as their essence.

Without puller

In order to confirm this assumption, let’s consider another replacement on a VAZ 2110 car. The reasons for the breakdown are the same.

1. Ruthless operation of the car on bad roads.
2. Incorrect driving.
3. Wear of the oil seal and the part itself.

The fact is that its cost is higher than the cost of the spare part that we are replacing, by about two or three hundred rubles, that is, at a hundred-ruble price, the bearing is three times more expensive

Therefore, the purchase of such an important device for our operation is not entirely justified. But on the other hand, the puller will be useful for many other types of work, therefore, if further DIY repairs are planned, the purchase becomes justified

So, let’s try to do without this device using a chisel and a hammer. The same could have been done according to the previously described procedure. Thus, we will need:

• wrenches - standard set;
• hammer;
• chisel;
• round timber of suitable diameter;
• Litol type lubricant.

At the initial stage, we prepare new spare parts. Next we follow the beaten path.

1. Just like with the “nine”, we first loosen the hub nut and wheel nuts.
2. We turn off the handbrake, jack up the car, and then remove the wheel.
3. We dismantle the brake drum similarly to the corresponding paragraph of the previous instructions.
4. Unscrew the hub nut.
5. We screw the bolts into two opposite holes in the hub one by one and pull the assembly necessary for disassembly towards ourselves - this is a way to do without a puller.
6. The inner race of our replacement part almost always remains on the axle. We pull it off using a chisel and a hammer, after removing the brake pads.
7. Having removed the retaining ring, as well as the oil seal, use a hammer to knock out the remaining part of the broken part using a round timber.

After lubrication, new spare parts are installed and reassembly is done.

So, we have described the process of replacing a VAZ 2110 bearing, you can study it in the video. One thing is clear: in a VAZ with front-wheel drive, changing a treasured part is also not so easy.

The same applies to replacing the bearing on a Kalina car. The technology is very close to what we described. Only the sizes of the turnkey nuts differ.

Well, those who had the opportunity to perform the operation we are describing in the unit of the corresponding Kalina suspension will easily be able to repeat the same thing on a car that is completely similar in design. More specifically, replacing a bearing on a Lada Granta car will not be difficult for them.

Repair prices by city

But not all car owners can or want to do such manipulations with their own hands. Many people find it easier to go to a car service center.

For such people, we have compiled a summary table of the average cost of replacing bearings in the rear hub of a VAZ in relation to different large cities of the Russian Federation. This is what happened.

It turns out that the price for repairing the rear suspension of VAZ cars is relatively quite low, even in the capitals. Therefore, it is worth thinking about whether to perform the operation yourself or go to the experts.

At the same time, as we found out, its cost to craftsmen is low, so all that remains is to weigh the pros and cons before you start doing the procedure yourself.

Wheel Bearing Adjustment

The main parameter when carrying out a replacement is setting the correct hub clearance. The procedure is performed in two ways: using a dial indicator or by touch.

First option:

1. Prepare an indicator stand.
2. Place the device on the brake disc and secure with bolts.
3. Place the end of the indicator against the end of the trunnion, as shown in the figure.
4. Rotate the hub to measure the play.
5. If the value is more than 0.15 mm, it is necessary to loosen the nut and tighten it with a torque of 9.6 N*m. Spin the disk several times. Loosen the nut (approximately 20-25 degrees), tighten with a torque of 6.8 N*m.
6. Check the backlash value.
7. Lock the nut.

Setting the gap without an indicator:

1. Put on the wheel.
2. Evenly tighten the nut while rotating the hub.

1. Rock the wheel in a vertical plane to “feel” for play. To do this, place your finger on the end of the trunnion. A barely noticeable gap should be felt when the wheel rocks.

1. If the play is caught, tighten the nut to a torque of 19.6 N*m. Don't counter.

1. Rotate the assembly several times in both directions (to self-install the bearing). Check the gap.
2. Lock the nut.

The rebuilt unit should rotate easily, without wedging.

Thematic videos:

Adjusting the hub clearance of the VAZ-2107:

How to adjust the backlash:

Manufacturers.

Domestic manufacturers:

• SPZ-Group
• LADA
• VBF
• Volzhsky standard

Foreign manufacturers:

• SNR (NTN)
• SKF
• INA
• NSK
• KOYO
• Timken

When choosing a quality product, it is better to buy from manufacturers of foreign brands. Domestic brands have a low price and are more widespread on the market than their foreign counterparts.

When replacing a product, it is extremely important to use high quality replacement parts. Low quality aftermarket products may not be sufficiently suitable for the application, causing end play problems. This can cause drivability problems that lead to costly returns. It is recommended to purchase only from official dealers or directly from the manufacturer.

Important Notes

A few points:

• When seating the clips using the impact method, it is necessary to carefully orient the plane of the spacer, avoiding accidental slipping;
• excessive application of the lubricant promises squeezing out the oil seal;
• Old bearing housings are suitable as a mandrel.

After adjusting the gap, you need to drive the car and listen to the bearing. If noise is noticeable or the wheel gets hot, you need to unscrew the nut, correct the play and tighten a new one.

Steering knuckle repair

Repair of the steering knuckle is possible with minor wear or minor damage. As a rule, if a unit is seriously damaged after an accident, car enthusiasts simply replace it with a new one.

Repair work is only possible after the steering knuckle has been completely removed from the vehicle. The repair schedule looks like this:

1. Clean the surfaces of the fist from dirt and dust, wipe it with a clean cloth, and blow with compressed air.
2. Clean the grooves for the retaining rings.
3. Inspect the steering knuckle after dismantling for signs of deformation and wear.
4. Install a new retaining ring and press the new bearing in until it stops.
5. If it is necessary to replace the trunnion, replace it. If the axle and kingpin are severely worn, it is recommended to replace the steering knuckle assembly.

Repairing the steering knuckle involves replacing the retaining rings and bearing. In case of extensive damage, only replacement is recommended.

Spare parts sizes

List of suitable spare parts with nominal size:

Installation of parts of other configurations is unacceptable by design.