Instructions for operation and installation of the Scher Khan Logicar 1 alarm system: how to enable autostart, connection diagram, key fob programming and video

The Scher Khan Mobicar 1 security system today is one of the most progressive and reliable alarm systems on the market.

The system is equipped with a variety of high-tech devices that make it possible to implement both the main functions of protecting the vehicle and additional ones related to eliminating the consequences of user inattention. Not many people know what this model is capable of.

We'll talk about this in more detail later in the article.

Equipment

First, let's look at the components that are included in the car alarm kit:

User's manual for installation. The documentation describes in detail how to install and connect the elements of the complex to the on-board network of the machine.
Instructions for use. Allows you to configure and correctly program the main options of Scher Khan Logicar.
Installation and connection map.
Main control module.
Pager. Used to control and adjust basic parameters and functions. Using the key fob, you not only turn alarm signals on and off, but also configure the complex.
Spare communicator. The device does not have a screen, but it also allows you to perform basic functions.
Installation kit. Includes power leads with connectors.
Impact controller. Used to record any physical impacts on the car body and send information about this to a pager.
The Valet button is intended to switch the system to service mode. Equipped with a wire with a connector for connection.
Transceiver with plug connected.
Engine blocking relay.
One limit switch. Can be used for installation on the hood or trunk door.
Siren.
Sticker for attaching the transceiver to the glass.

Scope of supply for scher khan alarm system

The kit includes:

Main key fob with LCD display and remote control;
Additional key fob – no screen, limited range;
Battery;
Case;
User guide;
Antenna module;
Shock sensor;
Car owner call sensor;
Thermal sensor;
Mounting block;
Siren.

The owner's manual explains the settings in detail, including setting the motor to start automatically, activating the clock, etc. After carefully studying the instructions, the driver will be able to configure the system independently.

Technical properties

Properties of car alarm Logicar 1:

the “signaling” uses Magic Code PRO 2 technology, which allows for protection against signal interception;
the operating range of the remote control with the control device is up to 1500 meters in alert mode and up to 500 meters when sending commands;
if the communicator is lost, the procedure for disabling the security mode can be carried out using a special password;
another code can be used to gradually disable the protection mode;
the turbocharged mode can be configured so that during its operation the cooling time of the engine turbine changes.

The Auto Project video shows how to hack the Sherkhan anti-theft system.

Security and safety

Ensuring vehicle security is the main reason for purchasing a security system. The creators of Mobicar 1 took this issue seriously, not forgetting to fill the system with many innovative solutions. These include:

Preventing road accidents. This is achieved by triggering an alarm when the vehicle brakes sharply. Other road users will be able to make a decision in time to avoid an accident.
Encryption of signals and use of a special radio frequency;
Sensors that allow you to monitor the possible movement of a car in space from a distance;
"Parking with engine running" function. Based on the name, you can imagine what this mode is like. It allows you to leave the vehicle with the ignition keys, leaving the engine on. Any abnormal event will shut down the engine.

Logicar 1 functionality

The main function of the alarm is to ensure the safety of the machine.

The system is equipped with the ability to start a car engine from a distance, the features of which are as follows:

the use of this option is allowed on cars with manual transmission and automatic transmission, as well as on cars equipped with an ignition with a Start/Stop button;
This option can be used on vehicles with engines powered by diesel fuel or gasoline;
you can adjust the start time of the internal combustion engine;
the option can be implemented in a time interval every two, four or eight hours;
You can start the internal combustion engine remotely by sending a command from the communicator.

Separately, we should talk about the functions of a pager with a screen:

as confirmation of completed or unexecuted options, a message is sent to the pager from the central module;
if you have a second car, then the pager can be linked to its alarm system, of course, when Sherkhan Logicar 1 is used on it;
the pager screen displays the operating time of the internal combustion engine when the Turbo mode, Pit Stop function or remote start is activated;
the communicator displays a two-way signal indication;
the screen displays the temperature level in the car interior;
the communicator can inform the car owner about changes in the voltage of the car's electrical network, the diagnostic command is sent from the pager;
the key fob allows you to determine the charge level in the gadget’s power source;
vibration alert option;
The energy saving mode will prevent rapid discharge of the power source in the key fob.

Anton Kovalev showed how the Logicar model works on Renault Duster.

Setting the time on the key fob Sherkhan 7 and 5, etc.

Simultaneously pressing keys I and III will allow you to set the clock on Medjicar car alarm models. Actions will be confirmed if Pro9 is displayed on the screen and a tone sounds. Next, a window will automatically appear where you can set the desired time. The dial that appears will blink continuously. Key 1 will adjust the hours, and key 2 will adjust the minutes. To exit the time setting mode, press these two keys simultaneously and hold them for two seconds.

Advantages and disadvantages

Advantages of Sherkhan Logicar 1:

Wide functionality. The model has the necessary options to protect the car.
Reliability. As a result of the installation, the consumer does not have to worry about the safety of the vehicle.
Low price. The cost of an anti-theft agent ranges from 3,800 to 5,000 rubles on average.
High build quality. All components of Sherkhan Logicar 1 are made in a durable casing, which prevents them from breaking as a result of falls or other physical impacts.

The disadvantages include the fact that, judging by consumer reviews, malfunctions may occur in the operation of the Sherkhan Logicar 1 alarm system. Usually this drawback is due to the fact that during installation the requirements that the car must meet were not met.

Alarm Sherkhan Magikar

A quality product does not need advertising. And the product that we will talk about today is complete confirmation of this. Sherkhan Magikar is a professional security system designed to service vehicles with diesel or gasoline engines, the on-board voltage of which is 12 V, in order to provide reliable protection and security.

The alarm system is based on three-stage vehicle protection and two-way communication via radio channels. It should be noted that it is possible to remotely turn on a car engine.

When the question arises about the safety of their own vehicles, car owners begin to look for advice on the Internet. We hope our review will help you understand some of the nuances and get to know the technology better. What to expect from the Sherkhan Magikar alarm system? Let's find out right now!

How to install an alarm?

Installation is done like this:

The battery turns off. This is required to deactivate the voltage in the on-board network. Otherwise, during installation, you may accidentally short the contacts on one of the devices to ground, which will lead to breakdown. To disconnect voltage from the battery, disconnect the cables with terminals.
Install the processor module in the cabin. Choose a location for installation so that the device is inaccessible to a criminal if the car is broken into. It is best to install the device behind the control panel; this place is the most difficult to access, and you will also have to disassemble the center console. Remove the steering wheel and dashboard trim, disconnect the plugs with wires from the device. Determine a free space behind the dashboard and install the unit in it. To eliminate the negative impact of vibrations on the device while driving, the module can be wrapped with foam rubber.
At the next stage, a siren is installed; it must be placed under the hood. Choose a location that will be least exposed to moisture and high temperatures. Installation of the device near the cylinder block is not allowed; subsequently the siren will melt and will not be able to perform its functions.
The shock sensor is mounted in the passenger compartment. It cannot be placed under the bottom; the controller will quickly fail as a result of exposure to dirt and moisture. Install the sensor in the center of the body, this will allow it to effectively detect impacts on the car from all sides. You can place the device on the partition that separates the engine compartment and the interior.
Install the antenna on the inside of the windshield. You can mount the transceiver under glass on the dashboard, but it is advisable that this element be located as high as possible in the cabin. This will ensure efficient reception and transmission of signals. Please note that the quality of the pulses is affected by the presence of metal objects near the antenna. It is advisable that they be located no closer than 4 cm from the device.
Install the limit switch to the hood. After installation, route the connection cable to the switch into the car interior.
Install the service key. The Valet button must be disguised, since it can be used to disable Sherkhan Logicar 1. You can hide the key in a bundle with standard wiring.

Video

The “Scherkhanalarm” channel spoke in detail about the security options of the Logicar 1 anti-theft system.

Do you have any questions? Specialists and readers of the AUTODVIG website will help you ask a question

Was this article helpful?

Thank you for your opinion!

The article was useful. Please share the information with your friends.

Yes (75.00%)

No (25.00%)

Please write what is wrong and leave recommendations on the article

Cancel reply

Rate this article: ( 4 votes, average: 4.75 out of 5)

Discuss the article:

User manual

Below we will analyze the main nuances from the technical manual for using and setting up Sherkhan Logicar 1.

Designations of buttons and symbols on the key fob

The designation of the buttons and indicators of the Sherkhan Logicar 1 key fob is presented below.

Purpose of indicators on the communicator

Purpose of buttons on the communicator

Communicator binding

Pager programming:

Turn off the protective mode of Sherkhan Logicar 1. With the ignition off, press the button located on the body of the diode element; the button is pressed for two seconds. The car's lights should blink once.
Then within five seconds you need to click on the button again. The lights will blink twice if no password is used. If there is a code, then the lighting devices will blink once.
If you use a password, then you need to enter its value. The lights in the car will flash twice.
After five seconds, the diode light will light continuously. This suggests that the consumer can register a new remote control. In total, Sherkhan Logicar 1 allows you to link no more than three communicators.
Within five seconds, click on the first key of the communicator. The procedure for binding the remaining remote controls is repeated in the same way.

Autorun programming

How to enable autorun:

Using the settings table, move option 2-13 to position 3. Thanks to this, you can change the assignment of channels for controlling the starter mechanism and ignition.
Using the remote control, set the time interval from the moment the starter is activated until the moment the engine starts. It is recommended to set the closest parameter from the table to option 2-20. If you are setting up a function for a car with a diesel engine, then you should specify the time interval for 2-21. When setting the parameter on vehicles equipped with an ignition system with a Start/Stop button, it is necessary to adjust option 2-25. If the vehicle is equipped with a turbocharged unit, then function 2-24 should be adjusted.
At the next stage, you need to configure several parameters that will ensure the correct operation of the function. We are talking about the time it takes to warm up the engine and the operation of the car's lights during automatic start. You also need to set the activation interval for the timer option and make adjustments to the number of engine startup cycles. If the engine is not working, then there is no point in draining the battery by endlessly trying to start it. Typically, specialists configure four start-up cycles.
After setting the parameters, click on buttons 2 and 4 of the communicator at the same time. This will activate the timer.
After setting the time, you need to press the fourth key ten times in a row. This will allow you to adjust the parameters. When the settings are determined, you need to click on keys 2 and 4. This will activate the option.

Repeat the setup steps in Sherkhan LogiCar 1 to disable the autorun option.

Modes

Description of the modes in which Sherkhan Logicar 1 can operate:

Activation of protection is carried out by pressing the first key; to deactivate, use button 2 of the communicator. When disconnected, the locking devices on the doors will open and the starter mechanism and motor will be unlocked. If the siren beeps six times during a shutdown, this indicates that an alarm has been triggered. Its operation is due to the activation of limit switches on the doors or hood. When the siren emitted five beeps when turned off, the system was triggered by a command from the shock controller. If the siren gives four signals, this indicates that the warning zone of the sensitivity controller has been activated.
To activate the car search mode in the parking lot, you need to click on button 1 of the communicator with the protection function turned on. The car's lights will flash five times and the pager will emit one melodic signal.
To open the tailgate, you need to hold down key 3 on the communicator for two seconds. If the security mode is activated, it will automatically turn off, but the door locks will not unlock. You can configure the trunk to open with the door locks unlocked.
The Sherkhan Logicar 1 status check mode is launched by briefly clicking on button 4. Information about the status of the complex will be displayed on the pager screen.
Activation of the Panic mode is carried out by holding the first key of the communicator for two seconds. To disable the function, press the first or second button.
To enable or disable the siren alarms, you can hold down the first and second buttons of the communicator.

Photo gallery “Tuning tables”

Options settings table part 1

Options settings table part 2

Options settings table part 3

Options settings table part 4

Alarm functionality Sherkhan

Important functions of Sherkhan Magikar

List of functions:

Remote control of a car engine;
The key fob screen contains information about the current state of the vehicle;
Measuring engine speed;
Turbo timer operating in intelligent mode;
Vehicle safety system with engine running;
Battery saving mode;
Parking timer, capable of recording the time a vehicle is left in a parking lot;
Locking the communicator keys;
Alarm.

Key fob functions

Displays the battery charge of the communicator;
“Battery Save Mode” - energy-saving operating mode;
Display current time;
Built-in alarm clock;
Parking timer;
Possible driving of a second vehicle;
Automatic screen backlight mode;
Inability to intercept MAGIC CODE;
Ability to turn security mode on and off using several buttons;
Commands are confirmed audiovisually;
Call with vibration;
High range of action – 1500 m;
Several key fobs can be stored in the system memory, the readings of which are synchronized;
Battery low display;
Display of temperature conditions inside the car interior;
Display of vehicle battery charge;
Displaying the time that the car engine has worked in autostart modes: “Pit-Stop” and “Turbo”;
Ability to set the engine auto start time;
Alarm messages come with a sound signal.

Functions of the processor unit

Automatic engine start with manual and automatic transmission;
Possibility of installing the system on diesel and gasoline engines;
Turning on the car engine using a remote control at a long distance;
Automatic engine start every 2, 4 or 8 hours;
Automatic switching on of the motor once a day at preset hours;
Automatic switching on of the motor, associated with certain temperature indicators, on-board network voltage or upon command from external devices;
Monitoring the start of a car engine using tachometer signals;
Automatic start of engines of vehicles equipped with the “Virtual Key” system;
PIN code for disarming the vehicle if the key fob is lost;
PIN code to open the vehicle if the keys are lost;
Two-stage security shutdown system;
Protection of a vehicle with the engine running;
Possibility of installing “hidden security” - without the use of alarm and warning signals;
Hands-free function - the owner can automatically open or close the car when moving away/approaching;
Priority opening of the driver's door;
Interior light delay control;
Positive or negative door sensors can be connected;
Setting the duration and number of door lock control pulses;
The ability to open or close door locks when the ignition is turned on/off;
Turbo timer with adjustable engine turbine cooling time;
Automatic activation of the security system;
Warning with an alarm signal about a possible emergency situation due to a door left open;
A warning signal and the lights are on when the system is armed;
Panic mode.

Basic faults

Errors and problems that the user may encounter:

Communicator failure. Failure to operate the pager may be due to low power supplies, so when the first problems appear in transmitting commands, check the battery. If it sits down, it needs to be changed. Open the back cover and replace the power supply, observing the polarity. If the problem is mechanical damage to the communicator or exposure to moisture, you need to disassemble the case and assess the condition of the board. Damaged components such as capacitors and contacts must be replaced and re-soldered, and contact elements must be cleaned in case of oxidation.
Damage to wires. During prolonged use, electrical circuits may be damaged, especially if they were laid in the area of moving parts of the body. Diagnostics will require the help of an electrician. If you have experience and skills, you can use a tester to find damaged wires. Electrical circuits must be replaced regardless of the nature of the damage.
Failure of one of the components. This could be a shock sensor, a processor module, or an antenna adapter. It is necessary to diagnose the contacts on these devices, and clean the oxidized connectors. For more serious problems, detailed diagnostics of the devices will be required. You can fix control unit malfunctions yourself if they are related to the hardware. When water gets on the device, it must be disassembled and dried. But in the case of software failures, it is recommended to entrust troubleshooting to experts, since the unit may need to be reflashed.
False positives. This problem is caused by errors made when adjusting the shock controller. In accordance with the instructions and installation diagram, it is necessary to adjust the sensor. It is necessary to reduce the sensitivity so that the controller is not triggered by passing cars. But the sensitivity threshold cannot be set to a minimum, since this will lead to the fact that Sherkhan Logicar 1 will not detect impacts on the car body at all.

Reviews about SherkhanLogicar 1

№	Positive
1.	Vitaly (avtozvuk.ua): my comrades recommended this configuration of the signaling system. Good price-quality ratio, manufacturer's warranty. I installed it at a service station and it works like a clock. The review is positive, my recommendations to car enthusiasts.
2.	Nikiforovich (rozetka.ua): I recently bought Sherkhan Logicar 1, I chose it based on the criteria of price - quality, customer reviews, availability of consumables for repairs. You won't find a better one in your price category.
3.	Dmitry (hotline.ru): I’m happy with the purchase of the secret police Sherkhan Logicar 1, there are no complaints. It’s not buggy, there were no false alarms. I installed it myself and did not contact service.
4.	Vladlen (avtozvuk.ua): installed security on Renault Traffic, the sensors are sensitive, overdid it with the settings. I loosened the sensors, now it's just right. I gained experience so that I can install alarms with my eyes closed.
5.	Ivan (ugonavto.net): I like the Shere Khan Logicar 1 signaling system, especially the buttons on the key fob. When your hands are full, you can always press and open the trunk lid.
6.	Konstantin (ugonavto.net): my positive review of Shere Khan Logicar 1. I bought it a year ago, it works flawlessly.
7.	Negative
8.	Vasily (avtozvuk.ua): I have been actively using the alarm system for more than a year, I installed it myself, without the help of service station workers. Lately it has often started to trigger randomly, even at night. I contacted the electrician at the workshop and said that there was a manufacturing defect. I will change it.
9.	Gennady (ugonavto.net): I installed a Chinese signaling system six months ago, and was disappointed in the quality and accuracy of the operation. I will change it to something more serious.
10.	Alexander (hotline.ru): the workmanship is poor, the belt is leatherette, worn out in the first month. I do not recommend the secret police Shere Khan.
11.	Viktor Petrovich (ugonavto.net): I bought a Chinese secret police - it was a waste of money. The wires are thin, the insulation is flimsy, the contacts are weak and not reliable.