How to reset the service interval on Skoda cars

According to the maintenance regulations, Skoda Rapid cars are operated at intervals of 1 year or 15 thousand kilometers. The maintenance interval must be reset at the same time as maintenance.

As you approach the service sign, an information message appears on the on-board computer display. The car's electronics remind the car owner that it is time to replace some consumables and check the condition of the car.

If you perform maintenance but do not reset the counter, the automatic reset will not occur. To do this, you will need to go into the menu yourself, follow the steps prescribed in the instructions, and again set the maintenance interval on the countdown of the next 15 thousand km.

Despite the release of a restyled version, the nuances of restoring the range on Skoda Rapid cars of the same model year 2014 and 2022 do not differ. Therefore, the instructions presented will be equally relevant for model samples of 2015, 2016, 2022 and even 2022.

In addition to the basic concept of maintenance intervals, there is also a technical inspection service. Resetting it to zero occurs in almost the same way as normal resetting. But there is one nuance that is important to remember.

The procedure for resetting the maintenance interval on Czech Skoda Rapid sedans and station wagons may differ slightly depending on the configuration. They share cars with a conventional on-board computer and a multifunction display on the dashboard.

Depending on this, appropriate instructions and different sequences of operations to reset the counter are applied.

How to reset the service interval on a Skoda Fabia

If the car was produced no later than 2010, it is enough to proceed according to the following scheme:

When the data is restored, turn off the ignition.
With the engine off, press the button next to the speedometer.
While holding the button, turn on the ignition.
The key must be turned to the right.

Video for cars before 2013:

For Fabia 3 New models from 2014, the reset occurs in the same way as described above. In Skoda Fabia cars starting from 2011, when the oil needs to be changed, an icon with a button appears on the display. The operation of resetting maintenance intervals is even simpler:

Now press the left button and the on-screen button should disappear.
Click the "Daily Mileage" button located on the right.
Release the daily mileage button.
Without releasing the key, turn the ignition key.
The ignition must be turned off.

To check whether the measures taken helped, you need to wait a few minutes. Then turn the ignition key again and look at the display. If everything works, there will be no icon on the screen.

Second method for vehicles with a multifunction display manufactured since 2011:

To reset, confirm the action by pressing the left button.
With the ignition on, press and hold the button on the right until the main menu opens.
Quickly press the second key, then press and hold the first.
Now you need to press and hold the first button again for a few seconds. When "Service Interval" is highlighted, release.
Press and hold the same button again. When the Setup message appears, release the button and press the Center button.
you can release the button once Reset is highlighted.
Turn off the ignition.

If you reset reminders on Skoda Fabia 2, produced from 2007 to 2014, the methods presented above will not work. The procedure is as follows:

The key icon should disappear from the screen. Immediately after this, turn off the ignition and wait until the display goes off.
you must hold down the key used to cancel the run.
Without releasing the button, insert the key into the ignition.
After this, you need to release the mileage clearing and press the button with the image of the folder.

Video instruction:

Manual Resetting the service interval indicator for maintenance and oil service

Resetting the service interval indicator (SIA) in modern VW, Skoda, Audi, Seat cars.

Remaining mileage or number of days until the next inspection service – Turn on the ignition.

Vehicles without information display MY 2013

– Press the -1- key 4 times. The remaining number of kilometers and days until the next service will be shown on the display -2-.

Vehicles with information display MY 2013

– Press button -2- on the windshield wiper mode switch lever for more than 1 second. The information display then shows MAIN MENU, follow the instructions. – Select the item Setup using the -B- key, briefly press this key and then select the item Service interval. – Display information about the remaining number of kilometers and days until the next service. The following appears in the instrument cluster display: Service in. km or . days. (TO in . km or . days.)

The remaining number of kilometers and days until the next service will be shown on the display -2-. The display will show the open-end wrench symbol and the number of days and kilometers remaining until the next inspection service for approximately 10 seconds. First, the remaining mileage and the number of days until the oil change service are displayed; after pressing the -1- key again, the remaining mileage and the number of days until the next inspection service are displayed.

If, after turning on the ignition, the “wrench” symbol -D- is displayed on the display for approximately 10 seconds, and the number -1- is displayed in position -A-, then the oil change service is approaching.

For vehicles with information display from model year 2014

Resetting the maintenance indicator in cars of the 2013 model year

The service indicator is reset using the tester -VAS- with the appropriate diagnostic cable. The maintenance indicator can also be reset using the buttons in the instrument cluster or on the windshield wiper switch

Resetting the maintenance indicator using the instrument cluster keys or controls on the wiper arm

– Turn off the ignition. – Keep button -3- pressed and turn on the ignition. – Release the -3- button and, no later than 20 seconds later, briefly press the -1- button once. After a short time, the indicator will switch to the normal image.

For vehicles with information display

– Press button -2- on the windshield wiper mode switch lever for more than 1 second. The information display then shows MAIN MENU, follow the instructions. – Select Setup using the -1- key, briefly press this key and then select Service interval and then select Reset.

During the inspection service, it is necessary to reset the service interval indicator for the inspection service. Select further in the tester: “Instrument cluster J285” → “Instrument cluster functions” → 17. Call for service”, and then “Check” or “Inspection service”. Follow the tester's instructions.

In the case of an inspection service in combination with an oil change, both maintenance indicators must be reset.

Vehicles without information display

– Turn off the ignition. – Press and hold button -3- while turning on the ignition until the “open-end wrench” symbol appears on the instrument cluster display: – Press button -1-. The “oil change service” indicator is now reset to zero.

Vehicles with information display

Vehicles without information display – Switch off the ignition. – Turn on the hazard warning lights by pressing the -arrow- button on the center console of the front panel.

– Press and hold button -3- while turning on the ignition until the “open-end wrench” symbol appears on the instrument cluster display:

– Press key -1-. The "inspection service" indicator is now reset to zero.

Vehicles with information display

– Turn off the ignition. – Turn on the hazard warning lights by pressing the -arrow- button on the center console of the front panel.

– Select OK in the information display to confirm the reset. The "inspection service" indicator is now reset to zero.

Resetting the service indicator from the 2016 model year

Resetting the service indicator using the instrument cluster key

When resetting the maintenance indicator using the instrument cluster key, the following must be taken into account: ATTENTION! Vehicles with flexible maintenance intervals (QI6) are automatically recoded in this way to fixed service intervals from the moment they leave production. Recoding back to flexible service intervals (QI6) is only possible using -VAS- After an oil change, the service indicator must be reset for the oil change service. During the inspection service, it is necessary to reset the service interval indicator for the inspection service. After the inspection service with a simultaneous oil change, it is necessary to reset both service indicators.

Vehicles equipped with the KESSY system: Close all vehicle doors. Close the luggage compartment lid and hood.

Resetting the “Oil change service” indication

Resetting the maintenance indicator for the “inspection service”

How to reset the service interval on a Skoda Superb

The service indicator shows how many kilometers are left until the scheduled service. A wrench icon will appear on the screen. The display shows a message after how many kilometers or days maintenance is required. If this time has arrived, the key icon will flash for 20 seconds when turned on. The message “Support Now!” will appear on the screen.

It is not difficult to restore data on Skoda Superb cars starting from 2008. But first you need to understand the location of the buttons on the multifunction steering wheel. On the right is a wheel with which you select menu items. You will also need a switch in the lower left corner with an arrow image, it is used to go to the settings section. The interval is reset as follows:

Turn on the ignition.
Press the switch under the steering wheel down and wait for the main menu to open.
The steering wheel switches will be used as arrows when navigating through menus.
you need to select “Settings”, then go to section “A”.
Next, you need to click on the word “Reset” when the screen asks you to answer “Yes.”

If an LCD display is installed, you will need to enter the menu to get information about how many kilometers are left before service. To do this, go to the “Settings” section. The operation is carried out as on the Fabia model with LCD screen.

Third method

If your Volkswagen Tiguan comes with a multifunction steering wheel from the factory, you can use it to reset the service interval.

In the case of a reset via the multifunction steering wheel, you must:

start the ignition on the Tiguan;
Press the arrows on the steering wheel several times to display the settings menu;
select the Service section;
then call the Reset menu;
confirm the action by clicking on the Ok button;
wait for the interval to reset;
press the OK confirmation button again;
exit the menu.

The procedure is quite simple, and therefore it should not cause any difficulties for the motorist.

How to reset the inspection service on a Skoda Rapid

The action algorithm is selected based on the installed on-board computer. Difficulties may arise if the manufacturer supplied the Maxi Dot system with a built-in VAG scanner. You can quickly restore readings if you follow the steps in this order:

With the ignition off, press the mileage switch for one day and do not release.
Turn on the ignition without pressing the button.
When the message to reset the service light by changing the oil appears on the screen, press the left button located at the bottom of the wiper arm.
The information should be cleared, you can remove the ignition key.

Skoda cars with a standard on-board computer have two separate reset buttons. The fast model uses a double button with the following symbols: Set - to change the display mode and reset data, 0.0 - reset the TO indicator.

If the car was manufactured after 2013, you must enable
You need to turn everything off, then press the “install” button, it’s on the right.
After a few seconds, turn on the ignition
Release the button.

It is not necessary to use the left side of the key named "0.0". Clicking sound when resetting the oil interval. The procedure is different for models equipped with a multifunction display. You need to turn on the ignition and follow the instructions:

Press and hold the lower right button until the menu opens.
Quickly press the bottom left button.
Press and hold the right button again until the “Setup” message appears.
Then briefly press the second key.
Repeat from step 3. A Help message should appear on the screen.
Repeat steps 4 and 5, wait until the “Reset” line appears
Click the button at the bottom left.
Turn off the ignition.

Step by step video:

Resetting the trip odometer to zero on a Volkswagen Tiguan

. Now let's move on to the most important step, how to reset the daily odometer of your Volkswagen Tiguan? However, this step is generally easy to complete; some of you, such as new Volkswagen Tiguan buyers, may not be familiar with how to go about this process. Now we will look at different approaches to resetting the trip meter on a Volkswagen Tiguan:

Hold the right button on the instrument panel for a few seconds until the trip odometer displays zero.
If this button does not work, you can use the right comodo meter by pressing the button on the end of it for a few seconds until the odometer of your Volkswagen Tiguan is reset to zero.
Finally, on some newer models you may need to go through your vehicle's center console and display, going through your vehicle's configurations to reset it to zero

Skoda Rapid Severyanochka › Logbook › Resetting the oil change reminder / then UPDATED

Good afternoon. Last night the car gave a warning and 30 days later I changed the oil. I immediately went online to find a way to reset this reminder. But of all the options, not one helped. It was possible to reset the inspection service, for example it will arrive in 365 days or 15,000 km. But I still haven’t figured out how to get rid of the oil change notification. I spent the entire evening, but the proposed options (with and without an emergency lane) did not work out.

UPDATED Thanks to the post by oleg32-71, I was able to reset the oil change reminder.

INSTRUCTIONS Six months ago I did this on my car, I found a recording on the disk. Procedure: - insert the ignition key, - press the button on the dashboard - without releasing the button, turn the ignition key and release the button - the message “Reset service data” will appear - press the button on the dashboard - the data will be restored. Oil service is restored in the same way. A second after releasing the button with the panel already inserted, the message “Reset oil change” appears, and after another second, “Reset inspection service”. Pressing again resets the selection. The changes will take effect the next time you turn on. It turns out that the messages come one after another, and in a second you need to have time to click the desired message.

Skoda Rapid oil

the Skoda power plant directly depends on the correct choice of engine lubricant and compliance with the timing of its replacement. The oil serves to protect the contact area of the engine's rubbing components from excessive wear and scuffing.

In addition, lubrication reduces shock loads. vibration, noise and plays a major role in heat transfer. For these reasons, it is forbidden to be careless in choosing engine oil, as this may lead to early major repairs.

Interval reset with Rapid multifunction display

1. Turn on the ignition. 2.

Press and hold button Fig127475. A more than 1 second to return to the main menu.

3. Press button Fig127475. A until Settings is highlighted.

4. Quickly press button Fig127475. B.

5. Press button Fig127475. A until “Service” is highlighted.

6. Quickly press button Fig127475. B.

7. Press button Fig127475. A until Reset is highlighted.

8. Briefly press button Fig127475. B to confirm.

9. The maintenance interval has been reset. 10. Turn off the ignition.

Replacement Regulations

In countries where LongLife maintenance periods are allowed, change is required every 30 thousand km. Due to the low quality of the fuel, the manufacturer does not advise Russian motorists to focus on this period. A replacement interval is set for them, which is every 15 thousand kilometers. Experienced owners advise reducing it to 8-10 thousand km. In addition, unscheduled replacement is needed in the following cases:

antifreeze started to boil;
water or other technical liquid has entered the engine lubricant;
in ignorance of when the last lubricant change was made and what consumables were used, for example, after purchasing the car.

Maintenance regulations or how is a car serviced?

The routine inspection procedure takes from 6 to 12 hours, depending on the workload of the official dealer’s booth in your region, and proceeds as follows:

Body inspection: Visual inspection of the integrity of the paintwork and anti-corrosion coating of body elements, as well as the windshield and all glass. Then the hood lock is lubricated and replaced with a new cabin filter, after which the exhaust pipes and fuel system are checked. Finally, clean the drain holes and drain box;
Diagnostics of the engine and transmission - replacing the oil and air filters and technical oil, then adding fuel additive G Next, replacing the spark plugs and refractor on the engine, after which the engine is checked for deformation and leaks. Also, on models with an automatic transmission, add new ATF fluid;
Checking the carriage: This is where the ball joints and tie rod ends are checked for distortion, then the bearings are checked for play. Additional diagnostics of the brake system and brake pads for damage and corrosion, after filling the brake fluid to the mark and cleaning the brake drum linings from dirt. Upon completion of the truck diagnostics, the suspension system is checked for leaks and deformation;
Gait analysis - measuring tire pressure and monitoring tread depth, after which the tire's expiration date is checked;
Electrical equipment monitoring - monitoring the condition of external lighting devices, diagnostics of batteries and electrical equipment control levers. Subsequently, the light optics and sound signal are checked and calibrated. Finally, the interior lighting is checked and the check count sensor data is reset. The sensor of the Era-Glonass system is also monitored;
Final work and control inspection: This stage includes a control train in the car, as well as filling out a service book and a technological inspection checklist.

Possible errors and problems

The recommendation is suitable for used Volkswagen Polo models, especially those imported from abroad or for those whose warranty period has expired. This error occurs due to a mismatch between the maintenance schedule and what is built into the computer.

If the sedan is new and under warranty, you cannot reset the counter. On the contrary, you need to contact the dealership and sign up for a scheduled service station. Otherwise, if the service book is not marked, the car will be void of warranty.

Reset on a regular on-board computer

First, let's talk about the nuances of resetting the service interval on a Skoda Rapid equipped with a conventional on-board computer. This is a fairly common configuration, since many Russians prefer the basic and medium version of the Skoda Rapid model.

And the multifunctional display of the on-board computer is already appearing in more expensive trim levels.

Maintenance information for Skoda Rapid

To reset the counter informing about the required service and remove the annoying notification on the on-board computer screen, you must follow the following sequence:

There you are asked to click “Yes” or “Cancel”. To select the desired item, use the shift lever on the steering column or use the gear shift buttons directly on the steering wheel. This already depends on the configuration of a particular model.
Switch off the ignition of the Skoda Rapid. Then press and hold the reset button.
After this, you should reset the mileage, then the previous value will appear on the display again.
Press and hold the 0,0 button for a few seconds.
On the instrument panel, directly below the on-board computer display and between the speedometer and tachometer wells, there are two physical buttons. Left and right. The driver should be interested in the one with the image 0.0 on it.
A message should appear on the trip computer screen prompting you to reset the maintenance interval.
Once the reset is confirmed, the counter is reset.
While holding the reset button, turn on the ignition. You just don't need to start the engine.

Now a few words about how to cancel a service inspection. In fact, the procedure for resetting the inspection is no different from resetting the maintenance interval on Skoda Rapid cars.

The only difference is that this inspection service resets with the emergency range pre-activated. First, turn on the alarm, then repeat all the procedures described above.

Maintenance Interval Reset Menu

Maintenance warning

According to the regulations, maintenance on Skoda Rapid cars is carried out at intervals of 1 year or 15 thousand kilometers. Simultaneously with the maintenance, it is necessary to reset the service interval.

As you approach the service mark, an information message appears on the on-board computer display. The car's electronics remind the car owner that it is time to replace some consumables and check the condition of the car.

If you carry out maintenance but do not reset the counter, the reset will not occur automatically. To do this, you will have to go into the menu yourself, carry out the actions prescribed in the instructions, and again set the service interval to the next 15 thousand km.

Despite the release of the restyled version, the nuances of resetting the interval on Skoda Rapid cars of the same 2014 and 2022 model years are no different. Therefore, the instructions presented will be equally relevant for models of 2015, 2016, 2022 and even 2019.

In addition to the basic concept of the service interval, there is also an inspection service. Resetting it is performed almost in the same way as normal zeroing. But there is one nuance that is important to remember.

The procedure for resetting the service interval on Czech Skoda Rapid sedans and station wagons may have some differences depending on the configuration. They separate cars with a regular on-board computer and a multifunction display on the dashboard.

Depending on this, the corresponding instructions are applied and the sequence of operations to reset the counter is different.

How to reset the service interval on a Skoda Fabia

When the data is restored, turn off the ignition.
With the engine off, press the button next to the speedometer.
While holding the button, turn on the ignition.
The key must be turned to the right.

Now press the left button and the on-screen button should disappear.
Click the "Daily Mileage" button located on the right.
Release the daily mileage button.
Without releasing the key, turn the ignition key.
The ignition must be turned off.

To check whether the measures taken helped, you need to wait a few minutes. Then turn the ignition key again and look at the display. If everything works, there will be no icon on the screen.

Second method for vehicles with a multifunction display manufactured since 2011:

To reset, confirm the action by pressing the left button.
With the ignition on, press and hold the button on the right until the main menu opens.
Quickly press the second key, then press and hold the first.
Now you need to press and hold the first button again for a few seconds. When "Service Interval" is highlighted, release.
Press and hold the same button again. When the Setup message appears, release the button and press the Center button.
you can release the button once Reset is highlighted.
Turn off the ignition.

If you reset reminders on Skoda Fabia 2, produced from 2007 to 2014, the methods presented above will not work. The procedure is as follows:

The key icon should disappear from the screen. Immediately after this, turn off the ignition and wait until the display goes off.
you must hold down the key used to cancel the run.
Without releasing the button, insert the key into the ignition.
After this, you need to release the mileage clearing and press the button with the image of the folder.

The choice of oil for filling into the Skoda Rapid engine and its cost

Depending on which power unit is equipped with the Skoda Rapid , the choice of engine oil that needs to be used during maintenance varies. VW long Life III 5W-30 oil from the factory and during maintenance

In a more powerful naturally aspirated engine with 105 hp. with a volume of 1.6 liters and a 75-horsepower 1.2 naturally aspirated engine should be filled with original VW Special Plus 5W-40 oil

The oil used in power plants must have VW 502.00 or VW 504 00 approvals. When serviced by an authorized dealer, VW 502.00 motor lubricant is poured into the engine. Oil with VW 504 00 approval is mainly used in vehicles serviced by LongLife service. Due to low-quality gasoline in domestic realities, the use of extended LongLife maintenance intervals is not provided for by the official manufacturer.

The Skoda Rapid uses a proprietary system for organizing and classifying motor lubricants from Volkswagen. It is not widely used among major oil manufacturers. For these reasons, it is difficult to find the required inscriptions VW 502.00 or VW 504 00 on many labels. If it is impossible to detect them, it is recommended to check for the presence of oil indexes ACEA, A2 or A3 on the canister. It is also necessary to check the viscosity. Its required value depends on the ambient temperature, time of year and wear of the engine. Approximate viscosities for the Skoda Rapid powerplant are shown in the diagram below.

In addition to the above criteria, you should pay attention to the manufacturer or brand of oil. The most effective lubricants in Skoda Rapid power units are shown in the table below.

How much does maintenance cost for a Skoda Rapid?

The first service, according to the concern’s regulations, will cost 7,500 rubles, and the second will have to spend at least 10 thousand. The cost of subsequent maintenance will depend on the intensity of use and the degree of wear of the vehicle components - the main cost of the procedure is the purchase of original spare parts and consumables.

The manufacturer also offers drivers a package of additional services ŠKODA Service Plus, which includes monitoring and diagnostic capabilities. Thanks to this package, drivers are guaranteed more comfortable driving and an additional guarantee of safety.

If you are servicing your vehicle yourself or have purchased a vehicle that displays a servicing message on your instrument panel display, you will need the instructions below. How to reset the service interval on a Skoda Rapid yourself.

Normal oil consumption in the Skoda Rapid engine

The official manufacturer sets the oil consumption rate for the entire line of engines at 1 liter per 1000 km. Experienced car enthusiasts consider this consumption to be very high. A good situation is when adding lubricant is not required from replacement to replacement.

Acceptable oil consumption can be considered consumption of 100-200 grams of lubricant per 1000 km. If the engine consumes of oil per 1000 km, then this is a reason to pay attention to the power plant and eliminate excess consumption.

How to reset service on Skoda Yeti

Drivers often have difficulties with this car. Reason: Yeti has different configurations and the range resets differently each time. Cars manufactured after 2013 have a clock button on the right and a reset button on the left. Below are detailed instructions for zeroing:

The service indicator should disappear. The ignition must be turned off and on again immediately.
Turn off the ignition.
If the message does not appear on the screen, you must press the button to set the clock.
you need to turn the ignition key and then release the switch.
Press and hold the service interval reset button for 5 seconds.
The program will ask if you need to clear the data. You need to turn the wheel to the right to the “Yes” sign and click on the center.
When it burns, the word “service oil” should disappear.”

Second method

There is another way to reduce the service interval.

In this case, you will need to carry out the following operations:

turn off the ignition on the crossover;
press the service reset button;
then start the ignition;
release the demand button;
briefly press the clock setting button and hold it for 20 seconds;
wait until the maintenance instruction goes out on the display;
turn off the ignition.

If, when resetting, the display returned to its basic information display configurations, you did everything correctly, and the reset on the Volkswagen Tiguan crossover was performed correctly.

How to correctly reset the service interval on Skoda Rapid cars

The Skoda Rapid model belongs to the subcompact class B according to the European classification. At one time, Rapid turned out to be a long-awaited new product from the Czech manufacturer. A high-quality car with German roots and an affordable price is quickly beginning to conquer the markets, starting with India.

The car is economical in price and has similar maintenance costs. As part of each scheduled maintenance, it is planned to carry out certain work to replace and diagnose the condition of the machine and its components.

After maintenance, car service technicians reset the maintenance interval. If you perform maintenance yourself, you will have to reset the meter yourself. It is not so difficult.

Maintenance schedule for Skoda Rapid: when should I take the car for diagnostics?

A scheduled technical inspection allows you to obtain a comprehensive assessment of the condition of the vehicle, which guarantees timely diagnosis of components for wear and replacement of parts with new ones. The Skoda Rapid technical data sheet specifies the following service periods:

The first maintenance is carried out after 15,000 km;
The second maintenance must be done after 30,000 km;
Third maintenance – after 45,000.

At the fourth maintenance, the dealer’s warranty expires and diagnostics are performed purely at the request of the owner. It is also important to know that after reaching a mileage of 100,000 km, it is recommended to carry out a diagnostic inspection either every 10,000 km or after 2 years from the previous one. After a major overhaul of the engine and transfer case, maintenance is performed again according to the algorithm described above.

Note! The timing of a complete vehicle diagnostic is only the manufacturer’s recommendations, until which the vehicle is guaranteed to operate without breakdowns or the need for repairs.

An expired note on scheduled maintenance in the vehicle registration certificate can only deprive the right to free service under warranty within the first 45-60,000 km and does not in any way affect the price of the car in the secondary market or the cost of repairs from official dealers.

This is interesting: How to use a tomahawk alarm key fob

How to reset the service interval

The appearance of a warning about the need for maintenance is a common problem that almost all motorists face. In this case, the display may flicker or the device may make annoying beeping sounds. In service centers, when resetting, they make an entry in the service book and attach a sticker indicating the date of the next maintenance. Manufacturers do not recommend downloading data yourself, as the indicator settings may be lost. But more often than not, there are no malfunctions in the operation of automotive systems.

Typically the service notice appears after approximately 15,000 kilometers or 372 days. But most drivers perform maintenance much more often, approximately every 5-7 thousand kilometers. After changing the oil and filters yourself, the “Service” message is displayed. After all, the system cannot recognize that the fluid has already been replaced. You can cancel this membership yourself without overpaying at the service station. You can restore the registered information if the “Service” indicator lights up on the screen.

Methods for resetting the maintenance interval in Skoda cars
System type	Check	Methods for recovering service data
Standard on-board computer	set and 0,0 buttons (change display and reset service)	folder button and 0,0 button	buttons on the windshield wiper stop lever	press and hold the right button for 5 seconds, turn on the ignition and turn the knob to the right or left	press and hold the right button, after 15 seconds insert a contact; release the button and select "Restore Service"
On-board computer Maxi Dot	buttons on the windshield wiper stop lever	multifunction buttons on the steering wheel	reset the service indicator without going into the menu
On-board computer with multifunction display	multifunction buttons on the steering wheel	buttons on the windshield wiper stop lever	go to the settings section from the menu and select "Reset"

Second way:

This method of resetting the service interval is applicable for the 2008 Skoda Superb, which is equipped with devices such as Yeti:

after which the display will return to working condition, you can turn off the ignition.
TURN ignition ON;
Using button No. 2, enter the menu and select “SERVICE”;
hold and hold button No. 1 until the service interval is reset;

Resetting service on Rapid 2014

Forum about the operation of Skoda Rapid cars (Skoda Rapid) 2012 – present.

Moderator: Conference moderators

Reply with a quote

Resetting service on Rapid 2014

Can someone tell me how to manually ask for olive oil and inspection at Rapid ’14. Thanks to everyone who responded.

dred3
Messages: 1 Joined: Fri Jul 31, 2015 11:49
AM Return to top

Reply with a quote

Re: Resetting service on Rapid 2014

Winny » Fri, 04 Sep 2015, 17:16

If I’m not mistaken, then I’ve already driven 40 thousand using the “lace” without resetting, I’m used to it)

Rapid 1.6 Elegance manual transmission + Nissan Tiida 1.6 Tekna AT Former Octavia 1.6 BSE manual transmission Was Opel Zafira 1.8 robot + Opel Corsa 1.2 manual transmission - Octavia Tour 1.6 AKL WTS manual transmission

Winny
Messages: 191 Registered: Wed, Aug 13, 2008, 0:09 AM From: Vidnoye, MO
Return to top

Reply with a quote

Re: Resetting service on Rapid 2014

papa1 » Fri, 04 Sep 2015, 19:17

dred3 wrote: Maybe someone can tell me how to manually ask for olive oil and inspection at Rapid ’14. Thanks to everyone who responded.

I might be wrong. at Off We press the ignition and keep the daily mileage. turn on the ignition but do not start it and press the buttons. turn on the ignition. If it does not work out . everything is the same, we just change places (daily and folders) hold the folders, turn on the ignition (hold everything) press the daily mileage, I threw it off for myself! It’s just that the whole circuit is left over from the VW Passata B5. It turned out that apparently everyone has the same vag! Please !

VAZ-011,099. Passat B5 were. Now - Rapid 1.6MPI manual transmission AMBI. + WR2 + RAD + 6E3 + PW1

papa1
Messages: 149 Registered: Wed, 02 Jul 2014, 8:29 am From: M.O.G.Dzerzhinsky

Website

to come back to the beginning

Reply with a quote

Re: Resetting service on Rapid 2014

novik67 » Fri, 04 Sep 2015, 19:41

what kind of daddies?

novik67
Posts: 53 Joined: Tue Jun 16, 2015 8:14 pm
Return to top

Reply with a quote

Re: Resetting service on Rapid 2014

alexiv » Fri, 04 Sep 2015, 20:52

alexiv
Messages: 2376 Registered: Wed, 08 Sep 2010, 12:49 From: Moscow SAO Begovoi
Return to top

Reply with a quote

Re: Resetting service on Rapid 2014

Winny » Fri, 04 Sep 2015, 22:06

Thanks papa1! It helped, everything worked out. First we hold down “0.0”, then ignition, then “folders”. But the video from YouTube is only for maxidot owners!

Winny
Messages: 191 Registered: Wed, Aug 13, 2008, 0:09 AM From: Vidnoye, MO
Return to top