Review of the instrument panel on the Lada Kalina: description of lamps and indicators

January 14, 2015 Lada.Online 559 915 0

The Lada Priora/Kalina instrument cluster is designed to display driving characteristics, the current state of vehicle systems that ensure traffic safety, as well as the correct operation of the entire vehicle as a whole. If you are a novice driver, then this description of the dashboard will help you understand the readings of instruments and indicators.

1. Tachometer. Shows engine speed in real time. The red scale zone indicates a dangerous operating mode for the engine;
2. Malfunction lamp of the electronic brake force distributor. To check, the lamp lights up red for a few seconds when the ignition is turned on. The burning of the lamp in other cases indicates a malfunction; when driving with a burning lamp, increased safety measures must be observed;
3. Battery charge lamp. To check, the lamp lights up red when the ignition is turned on and goes out after the engine starts. If the lamp is lit in other cases, it indicates a lack of battery charge;
4. Left turn signal lamp. Flashes when the turn signal or hazard lights are on;
5. Speedometer. Shows at what speed the car is currently moving;
6. Engine oil pressure warning lamp. To check, the lamp lights up when the ignition is turned on and goes out after the engine starts. In other cases, the lamp is lit indicating low pressure in the engine lubrication system. It is not recommended to operate the engine in such conditions;
7. Right turn signal lamp. Flashes when the turn signal or hazard lights are on;
8. Handbrake lamp. Lights up red when the parking brake is applied;
9. Coolant temperature gauge. Engine operating temperature is 90 degrees and above to the red zone. It is prohibited to operate the vehicle if it overheats. When the arrow reaches the red zone, a buzzer will sound. To extend engine life, it is recommended not to operate the engine at high speeds until the coolant temperature reaches operating temperature;
10. Gasoline level indicator in the tank. The arrow shows the fuel level. Lack of gasoline can damage the fuel pump;
11. Fuel reserve lamp. Lights up with an accompanying buzzer signal when there is less than 10 liters of fuel left in the tank;
12. Button for switching display modes and resetting daily mileage readings. A short press switches between daily and total mileage. When you hold the button, the daily mileage is reset, accompanied by a sound;
13. Hazard warning light. Flashes red when the emergency lights are turned on simultaneously with the turn signals.
14. Electric power steering (EPS) malfunction lamp. To check, the lamp lights up yellow when the ignition is turned on for a few seconds. Lighting of the lamp in other cases indicates a malfunction of the EUR;
15. Headlight high beam lamp. Lights up when the high beam headlights are turned on;
16. Lamp for turning on external lighting. Lights up when the headlights are turned on or the headlights are low beam;
17. Airbag system malfunction lamp. To check, the lamp lights up yellow when the ignition is turned on for a few seconds. In other cases, if the lamp is illuminated, it indicates a malfunction in the airbag system. In this case, in the event of an accident, the airbags will not deploy;
18. Immobilizer lamp. If the system is working properly and the engine is allowed to start, when the ignition is turned on, the lamp flashes once and goes out. If the lamp flashes constantly (accompanied by short beeps), then the system is faulty. If, after turning on the ignition, the lamp lights up for 15 seconds and goes out, then the anti-theft system is not activated;
19. Liquid crystal display of the on-board computer (BC). Displays daily and total mileage, as well as information from the BC;
20. Seat belt warning light (optional). The lamp lights up when the driver's seat belt is not fastened, accompanied by buzzer signals for 1.5 minutes;
21. Brake system emergency lamp. To check, the lamp lights up red when the ignition is turned on for 4 seconds. In other cases, the lamp is lit indicating an insufficient level of brake fluid, or another malfunction of the brake system;
22. Front passenger airbag lamp (optional). Passenger airbag deactivation lamp;
23. Anti-lock braking system fault lamp (optional). To check, the lamp lights up when the ignition is turned on and goes out after a few seconds or after the engine starts. When the lamp is lit, there is a malfunction in the ABS system, but the brakes remain fully operational;
24. Engine management system malfunction lamp (Check Engine). To check, it lights up when the ignition is turned on and goes out after the engine starts. In other cases, the lamp is lit indicating a malfunction in the system. See the error code.

Error codes

Self-diagnosis mode displays certain codes. Due to the simplicity of the design of the diagnostic unit, digital values ​​only indicate the area where the fault occurs. The most popular encodings:

• 2 – there is a short circuit in the on-board network with a critical increase in voltage;
• 3 – open circuit or malfunction of the float in the gas tank;
• 4-5 – error or breakdown of the antifreeze or ambient temperature sensor, respectively;
• 6 – the motor is very overheated;
• 7 – too low oil pressure in the engine boat;
• 8 – the brake system is not working properly;
• 9 – the battery is faulty or severely discharged;
• E – standard error of the firmware data package;
• 0 – no errors – all on-board systems are operational.

Specialization : Graduated from the State Automobile University, worked for 20 years at GAZ-56, now I drive a Zhiguli.

Source

Correct installation of the Kalina 2 dashboard

Mount the instrument panel according to the standard scheme. First, clean the parts from dust and clogging. Check the integrity of the housing and replace the light bulbs if necessary. The temperature in the cabin should not fall below +15°C. In winter, it is recommended to carry out work in a heated garage or similar room.

Installation of the instrument panel:

1. Connect the electrical connector and battery.
2. Check the operation of the instrument module.
3. Disconnect the battery.
4. Screw the shield with 4 bolts.
5. Install the decorative panel and secure it with 2 screws.
6. Replace the protective plug or fuse box cover.

see also

Comments 182

Please tell me how to solve the problem? . The problem is that the warning lights (!), (ABS), (ESP) are constantly on, so these systems are not included in my configuration. Some people advise to reflash the device, others say that the problem can be solved in 5 minutes using a programmer. What needs to be done to keep the warning lights off?

And another question, in order for this dashboard to work correctly on Kalina Cross, do I need firmware 2192-50 1.2? The photo shows what it is like now. Now my low beam and high beam are not working at the same time, and the emergency lights are not working properly.

Is it the same with two screens? Why connect to the power supply when you can rearrange the jumpers, what is the difference?

I flashed grants for the tidy, everything works except for the backlight, that is, the screen lights up but where the arrows are there are no numbers, if you do a test of the tidy, everything lights up

Hello . Is it possible to flash a Priora 2 tidy with firmware 17 to 19?

Hello, I ordered USBDM v-4.95, but the Chinese sent USBDM-jb16-001, not USBDM-js16-001. Will it be possible to flash the KALINA 2 tidy and what needs to be done. THANK YOU.

I have USBDM-jb16-001. Still doesn't want to sew. It just doesn’t select the firmware, it gives an error

Thanks for the article and the used firmware! I edited the mileage, flashed the tidy from Granta Lux and put it in Kalina!

I don’t think it’s relevant anymore, but still. you need to reset the device. because this abs data is recorded when the device is connected to the car. I did that, everything is fine

Yes that's right. The problem has already been solved. Nevertheless thank you.

I don’t think it’s relevant anymore, but still. you need to reset the device. because this abs data is recorded when the device is connected to the car. I did that, everything is fine

You need to do everything as written in the article above. Select EraseSelective and check the box. (if you want to reset the mileage and erase the immo, use EraseMass or erase all)

Expert opinion

It-Technology, Electrical power and electronics specialist

Ask questions to the “Specialist for modernization of energy generation systems”

Fuses and relays of the mounting block To obtain four-digit combinations of faults, you need to use special equipment or resort to the services of service station specialists. Ask, I'm in touch!

Why did it happen so?

Perhaps the automatic requests do not belong to you, but to another user accessing the network from the same IP address as you. You need to enter the characters into the form once, after which we will remember you and be able to distinguish you from other users exiting from this IP. In this case, the page with the captcha will not bother you for quite a long time.

You may have add-ons installed in your browser that can make automatic search requests. In this case, we recommend that you disable them.

It is also possible that your computer is infected with a virus program that is using it to collect information. Maybe you should check your system for viruses.

If you have any problems or would like our support team, please use the feedback form.

The instrument panel serves to inform the driver about all important processes occurring in his car. It is by using the scales, indicators, symbols and lamps located on this device that the person sitting behind the wheel is able to monitor the performance of components and systems. For the shield to function correctly as a single system, it requires regular diagnostics. It consists not only of scanning by connecting electronic reading devices to the computer, but also by visually monitoring the performance of all specified components of the dashboard (lamps, etc.).

About tuning the instrument cluster

The instrument panel in the LADA Kalina car is covered with a cover, which is made in the form of an overlay on the adjacent area of ​​the panel. If there is a need to dismantle the trim, then this is not at all difficult to do, and then the instrument cluster can be easily changed.

The instrument panel can be upgraded by changing its exterior.

Important! The combination of instruments that the manufacturer uses in the LADA Kalina is identical to those installed on the VAZ 2118 and VAZ 2119 modifications.

There is a very popular variant of the combination “GF 618” on sale. The functionality of this product is implemented using diode technology, in addition to which the interface contains a route controller. Many owners get tired of the standard dashboard and are haunted by the thought of tuning the LADA Kalina. Alternatively, you can take your time purchasing a fancy diode combination, the cost of which can easily shock you.

Do-it-yourself upgrades are also available to most enthusiasts. Among the simplest transformative measures is the purchase of an inexpensive overlay, which can be ordered in many online stores.

If we look at the instrument panel, Kalina presents a coherent design that combines the main indicators of the vehicle’s performance. There is not a single car that does not have such informative signs. Knowing the Kalina instrument cluster allows you to determine what condition the car is in.

About controls that do not touch the dashboard

The main elements include the following attributes of the driver's seat:

• clutch pedal;
• pedal drive brakes;
• accelerator pedal;
• of course, the steering wheel.

The central part of the panel also has additional “organs”:

• levers and regulators that control the heating and ventilation modes of the interior;
• climate system activation organ;
• Lada Kalina stern glass heating button;
• mechanism for opening and removing the ashtray.

Why you should know the pinout

But before you start this kind of upgrade, you need to understand which wire leads where. The pinout of the instrument panel of a VAZ-2110 car is a very important point when “tuning”. Without this, you risk simply getting confused in a fairly large number of wires, buttons and various sensors. The pinout will be useful in any case - both when making minor improvements and when completely replacing the instrument panel.

The process of installation and dismantling itself is quite labor-intensive, but if you know the correct sequence of actions, then there is nothing particularly difficult about it.

For these works you will need a minimum set of tools - a screwdriver and pliers.

For those who are doing this for the first time, it is best to stock up on self-adhesive pieces of paper, like those on which prices are written in stores, and a pen. With their help, at the time of disassembly, you will indicate, firstly, the sequence of dismantling the parts, and secondly, which wire is connected where. At first glance, this may seem time-consuming, but in fact, for beginners, such markings will help them put the panel back together faster.

At the same time, before starting work, it is best to stock up on a pinout diagram - at least conditional. After all, during the work process you need not to confuse anything and correctly understand each wire and connection during the reassembly process. It is worth noting one very important point. By and large, understanding the pinout of the panel of the “tenth” family will not be difficult even for a beginner.

But you need to remember that there are certain differences here, depending on the plant where the car was manufactured and the year of its manufacture. For example, the instrument panel may be an old model, with a mechanical odometer. If the odometer is electronic, then this is a newer version. Accordingly, there are certain differences in pinout between these panels.

Indicators included in the panel

The Kalina dashboard consists of 23 main elements. These include:

• rotation speed meter;
• indicator showing battery charge;
• speed meter;
• indicator displaying lubricant pressure in the engine;
• temperature indicator;
• turn signals;
• fuel level sensor in the tank;
• hand brake;
• daily mileage reset;
• reserve fuel quantity lamp;
• computer display.

Possible faults

The following malfunctions are possible with the dashboard:

1. Fuel level or temperature gauges do not work. The reason may be faulty sensors or damaged wiring.
2. When the tank is full, the fuel level needle drops to the zero position.
3. The arrow on the fuel level indicator moves abruptly and often drops to the zero position.
4. The fuel reserve indicator does not go out.
5. If any indicators on the device do not light up, the reason may be burnt out light bulbs, insufficient contact between the light bulb socket and the printed circuit board, oxidation of contacts, broken wires, or a malfunction of the indicator sensor.
6. If the speedometer is not working, the reason may be in the flexible drive shaft of the device: the nuts are poorly tightened, a break, mechanical damage, etc. (video author - RasH19).

What do the icons on Kalina's dashboard mean?

• 1 – standard tachometer. The dial indicator is divided up to 7000 rpm with a threshold of 500 rpm;
• 2 – Check the engine. A standard lamp found on all modern cars. Indicates a serious engine breakdown and the need for urgent repairs;
• 3/9 – indicators indicate the turn signals are turned on;
• 4 – the oil pressure in the engine has greatly decreased;
• 5 – ABC is faulty and usually goes out when you turn the key;
• 6 – immobilizer operation indicator;
• 7 – the indicator has a simple meaning, it indicates that the motor is overheating;
• 8 – parking brake status indicator;
• 10 – the battery symbol shows the battery charge status;
• 11 – odometer;
• 12 – indicator of the state of the exchange rate stability system;
• 13 – the need to shift to a higher gear is not established in most versions;
• 14 – high beam indicator lamp;
• 15/17 – indicator of normal operation of stern/front fog lights;
• 16 – low beam indicator;
• 18 – daily mileage reset key;
• 19 – standard display;
• 20 – icon indicating that the doors are closed correctly;
• 21 – critical drop in fuel level in the gas tank;
• 22 – an exclamation mark inscribed in the tire profile indicates a punctured wheel;
• 23 – if the lamp goes out after starting the engine, the power steering is working normally;
• 24 – requirement to fasten seat belts;
• 25 – exclamation mark is used only in some vehicle configurations;
• 26 – airbag operation indicator.

The badges are only relevant for hatchback and sedan versions of certain versions. Depending on the year of manufacture and configuration, the symbol designation may differ from the nominal value.