Replaced the speed sensor but the speedometer does not work


Why the speedometer on the Lada Priora may not work

The stable operation of injection power units depends on the synchronous functionality of all electronic components.

One of these important components is the electronic speedometer. The article will answer the question why the speedometer on a Lada Priora car does not work. Symptoms, causes of failure, and methods for checking damaged elements of the entire system will also be described.

Private situations

General signs do not always indicate specific breakdowns. There may be exceptions.

If individual devices refuse to work, it is quite possible that this is their personal problem. You'll have to parse the specific pointer. It may have a cracked gear that needs to be replaced.

Also, why doesn’t the instrument panel of the VAZ 2114 work? If the fuel gauge and tachometer are capricious (either they function, or they don’t react at all), the contacts and the mounting block are normal - you need to do a small check.

Reset is pressed and held, and the ignition is turned on at the same time. Raised arrows indicate the need for further searches. Lifeless - that microcracks have appeared in the shield itself. You will have to remove it and examine all soldering and traces under a magnifying glass. In principle, these are all the main options. If calling all the listed components and parts did not lead to the revival of the instrument panel, your case is individual, and you will have to determine the situation in the company of an experienced auto mechanic.

Layout and operating principle

The Lada Priora model is equipped with a fully electronic speed calculation system. It consists of the following elements:

  1. Speed ​​sensor (EMF). Its function is to create electrical impulses.
  2. Electrical wiring. Powers the speedometer system with electric current.
  3. Fuse. Protects the system from voltage surges.
  4. On-board computer. Monitors work and analyzes incoming data.
  5. The speedometer itself. Necessary for visual speed control.

There are not many components in the system. The system works as follows:

  1. The speed sensor produces electrical impulses. It is installed on the gearbox housing. On power units with 16 valves, the EMF is located on the side of the expansion tank. The EMF is installed opposite the flywheel. This gear has teeth along its entire diameter. There is only one tooth missing in one place. It is to this place that the magnetic speedometer sensor reacts. During the passage of an empty space, the EMF opens, thereby creating an electrical impulse.
  2. The pulses generated by the opening are sent through wires to the ECU. The computer calculates the speed at which the signals arrive and converts them into an electrical voltage of a certain strength.
  3. Voltage is supplied to the instrument panel, activating the speedometer drive motor.
  4. The electric motor deflects the speedometer needle by a certain degree.

In addition to needle deflection, electrical impulses from the speed sensor are necessary to calculate the fuel supply to the engine. Based on the data received, the on-board computer determines the required amount of combustible mixture and its filling with air. In this way, the required, stable engine speed is maintained for the current speed limit.

The speedometer on the Priora does not work for several reasons. But this is always preceded by the appearance of a number of symptoms of a malfunction. They will be described below.

Checking the condition of the wires

When operating the car on not very good roads, one of the wires that goes to the dashboard from the speed sensor may break, which leads to damage to the speedometer. A special tester will help determine the integrity of the wires; if the wires are not damaged, the device will notify you of this with a signal, but if the signal does not arrive, the wire must be replaced with a new one.

Experts recommend not only checking the integrity of the wires, but also analyzing the functionality of the following elements:

  1. Check whether the contact goes to the column that connects the wires to the speed sensor. Quite often, contact is lost due to oxidation, and it will be possible to resume the operation of this element after the plaque has been thoroughly removed.
  2. Check the functionality of the motion sensor using a special scanner. If during the test the device reveals interruptions in operation, the element will need to be replaced with a new one.
  3. Check the functionality of the dashboard. To do this, you need to remove the printed circuit board from the dashboard and visually inspect its condition. If traces of oxidation are noticed at the connection point or a so-called “track break” is detected, the board must be replaced.

Symptoms

Drivers accustomed to carburetor engines often do not react to the appearance of symptoms of speedometer failure. On injection engines, you need to pay attention to the behavior of this device. Symptoms of failure are as follows:

  1. The instrument needle does not work completely or partially. It can periodically turn on, tremble, freeze at a certain level.
  2. Complete failure of the instrument panel.
  3. The speedometer determines the speed limit with a large error.
  4. The engine is losing power.
  5. Fuel consumption increases noticeably.
  6. The stability of the power unit at idle speed is lost.

All these signs are the result of a breakdown or malfunction of the components of the speed calculation system. A detailed analysis of the reasons will be given below.

Malfunctions

If the speedometer on a Priora stops working, then you need to check each of its components step by step. It's better to start with the device itself.

Drive unit

The drive is checked by simply disconnecting the negative terminal of the battery. After reconnecting the terminal, the on-board computer reboots the system. Next, you need to reset the odometer, hold down the reset button and turn on the ignition. The tachometer and speedometer needles should deflect to the maximum. If this does not happen, then electrical voltage is not passing through these devices.

You can conduct an additional test of the speedometer's performance. On a Priora, the speedometer may not work due to a failure of the signal receiver drive. To check you need:

  1. From the “+” terminal of the battery, run a wire to terminal “26” of the red connector.
  2. With short touches you need to simulate the arrival of signals from the EMF.
  3. The arrow should deflect each time terminal “26” is touched.

If there is no response to the incoming voltage, you will have to dismantle the panel and remove the instrument printed circuit board. It needs to be inspected for breaks or oxidation of soldering and tracks. The oxidation needs to be cleaned, and the broken tracks need to be soldered with jumpers. Next, perform the following test:

  1. Set the tester to resistance measurement mode.
  2. Connect the red measuring probe to terminal “26”.
  3. Apply the black test lead to ground.
  4. The pulse input should show an operating resistance of up to 3 ohms.

If these readings are not present, then the fault lies in the radio components of the drive or its motor has burned out. Without special knowledge, such breakdowns cannot be repaired on your own. You'll have to change the drive.

Fuse

The speedometer is protected by fuse “F1”. It is located in the safety block under the dashboard, on the driver's side. It is necessary to remove the element and check the condition of the internal jumper.

If it is broken, you need to replace the element with a 10 Ampere analogue. Before replacing, it is important to clean the fuse contacts from oxidation and possible carbon deposits.

After replacement, you need to check the operation of the speedometer again.

Wiring

It's just that fuses don't blow. This was preceded by a short circuit or high voltage.

It is necessary to carefully check the wiring for breaks, deformation, and lack of insulation. All defects found must be eliminated.

If the Priora's speedometer does not work, the cause may be the speed sensor. Its verification is carried out sequentially. First you need to check the condition of the connecting plug. It is necessary to open it and inspect the contacts of both parts of the socket. If dirt, moisture, or oxidation is detected, clean with a solvent. Next, you need to check whether the electrical voltage reaches the sensor itself. Necessary:

  1. Set the multimeter to voltmeter mode to measure DC voltage.
  2. Connect the red test probe to terminal “1” of the wiring cable.
  3. Connect the black probe to terminal “3”.
  4. Turn on the ignition.

The voltmeter should show a result equal to the battery voltage. If voltage is supplied, then the sensor’s ability to generate electrical impulses is checked. This test requires:

  1. Raise the drive wheel of the vehicle on a jack.
  2. Connect one end of the control wire to terminal “2” of the sensor.
  3. Connect the red probe of the multimeter to the second end of the control wire.
  4. Connect the black test lead to ground.
  5. Insert the plug into the EMF socket.
  6. Turn on the ignition.
  7. Rotate the drive wheel of the machine.

As electrical voltage is applied to the sensor, it must produce electrical signals. The tester defines them as a pulse voltage from 0.6 to 12 volts. If there is no response from the tester, then you will have to dismantle the EMF to check.

To dismantle, you need to loosen the air purification filter pipe. The EMF is immediately visible directly below it. Its dismantling is carried out using the “10” key. You need to unscrew the mounting bolt and turn the sensor a little. Next, you need to pry the device with a screwdriver and remove it from its seat.

The main reasons for speedometer failure

First, you need to make sure that the source of the trouble is not bugs in the chip itself, on which the vehicle operates. While the machine is in use, the so-called cache in these chips is filled with information. This is why failures occur, including temporary ones. The “mass” from the battery is simply reset in this case. Otherwise, you will not be able to reset your data. In this case, the on-board network in the vehicle is completely de-energized.


What should you do if your car smells like burnt oil? You will find the answer in our material.

How to remove the bumper on a Priora and how difficult it is to replace it - find out here.

If resetting does not help get rid of the problems, conduct a full system check:

  1. Check the fuse plate installed on the board in the power circuit. The required part will have the designation “IGMETER”.
  2. After this, it is necessary to diagnose the serviceability of the wiring located in the area, starting with the speed registration sensor and ending with the instrument panel. It is in this section that the wires begin to break. Clinching may occur and other types of defects may appear. This usually occurs due to heavy use of the vehicle.
  3. The contacts located in the connectors require special attention. And they can become unsuitable for use due to the formation of rust and high acidity. In this case, the contacts of the sensor and connectors can be easily cleaned to get rid of defects.
  4. The next step is to check the monitoring sensor based on the distance traveled by the vehicle. If you contact a service center, special equipment is used to check this part. If it is missing, then the check is performed when the car drives several kilometers. As the countdown continues, we can say for sure that the system is working properly.

What to do if the speedometer on a Priora does not work due to the dashboard

If this is where the malfunction lies, then you will need to get to the mechanism that rotates the arrows. And conduct a thorough inspection. It is recommended to drive the car into a garage box and set the vehicle's parking brake. After this, open the hood of the car and disconnect the terminal marked with a minus from the battery. Thanks to this action, you will not be afraid of a short circuit in the on-board network.

Almost anyone can remove the dashboard on a Lada Priora. Photo: tuningtaza.ru

The next stage is careful dismantling of the torpedo. And here we need to perform several actions.

  1. First, remove all the pads completely.
  2. Then carefully unscrew the steering wheel.
  3. Remove the switches located under the steering wheel.

The next stage is detection and unscrewing of self-tapping bolts. They allow the torpedo to gain a foothold in its place. Only when all these steps have been completed can you begin dismantling the torpedo itself. To do this, just grab the part, pulling it slightly towards you. Then the wires are disconnected. But before that they are marked so as not to be confused later. The torpedo is pulled out and carried through the passenger door.

Other causes of malfunction

It is not yet known how problems with the speedometer will persist in the new generation of Priora. Photo: smolmotor.ru

Deflection of the arrow axis is another reason why the device may fail ahead of time.

In this case, several recommendations are also given:

  • First, remove the arrow itself, very carefully.
  • To do this, place a small fork made of plastic under the arrow.
  • The device must be lifted up, carefully, without haste.
  • If the arrow was indeed bent, then it is enough to simply replace it.

The rotation of the speedometer is ensured by special gears located on the back of the dashboard, at the rear. Each gear requires inspection if there are any problems with the speedometer. If necessary, parts are replaced, there should be no problems with this.

Speed ​​sensor malfunction

Failure of the speed sensor (in diagram No. 11) is one of the reasons for the speedometer not working. The sensor is located on the gearbox, where it is screwed with one screw, and three wires go to it. On a Lada Kalina with a 16kL engine, you can find the sensor on the side of the washer reservoir. In a car with an 8-valve engine, it is recommended to remove the bellows of the engine air filter to access the sensor.

The sensor catalog number can be: 1118-3843010, 2170-3843010, 2170-3843010-02. The surest way to find out which speed sensor is installed on your car is to remove it and look at the part number. However, do not rush to buy a new sensor, first check the contact in the plug; the speedometer may not work due to oxidation of the contacts, or the wiring is damaged. Also, the cause of a malfunction of the speed sensor may be the presence of metal shavings or other foreign particles on its surface.

Car enthusiasts have noticed that if the speed sensor malfunctions, the electric power steering also does not work (the steering wheel becomes very light, or vice versa, heavy) and the CheckEngine lights up. In addition, there are problems with speed (E-Gas).

If after replacing the speed sensor the speedometer still does not work, then it is possible:

  1. speed sensor turned out to be defective
  2. The speed sensor does not fit this vehicle.
  3. The cause of the malfunction is not the speed sensor

Complete failure of the speedometer

The easiest way to check the condition of the electrical circuit is to disconnect the battery for a short time. As a result of this action, the on-board computer settings will be reset and restored to their original settings. If after the operation the fault has not been eliminated, then one of the components of the circuit responsible for the operation of the speedometer has failed. Therefore, it will be necessary to find the cause of the current situation and eliminate it. As with any electrical circuit, troubleshooting should start from the simplest.

Often this problem occurs after the car has been parked in the rain, which has led to water flowing into the contacts, which causes interruptions in the operation of the circuit.

Car speed sensor

ExaminationDescription
1FuseYou need to check the condition of the fuse responsible for the operation of the instrument panel in the fuse box. This fuse is designated “IG/METER” in the circuit. There are often cases when this fuse blows. If it is damaged, it needs to be replaced and then checked to see if the original problem has gone away. If after replacing the fuse the problem does not disappear, you should look further for the cause.
2WiresThe next step will be to check the condition of the wires running from the speed sensor to the dashboard. Driving on poorly paved roads may cause one of the wires to break. A tester can quickly check the condition of this wiring. If one of the wires breaks, it should be replaced.
3ContactsIt is also worth checking the contact in the block through which the wires are connected to the speed sensor. Very often they oxidize, thereby disrupting the connection between the sensor and the wiring. If plaque is noticed on the contacts, it should be cleaned off. After the operations, you need to check whether these procedures gave a positive result.
4Motion SensorThis can be done by connecting a scanner to it. If, after diagnostics, malfunctions in the operation of the sensor are identified, it is replaced. If it is not possible to connect the scanner to the network, you can determine its performance using the kilometers traveled counter, which is located on the instrument panel. When the speedometer does not work, and the counter counts kilometers while driving, the motion sensor is working properly and the reason needs to be looked for further.

If all the above work has been completed and it does not bring a positive result, you should look for the cause of the problem in the dashboard.

First you need to check the condition of the instrument panel circuit board. To do this, you need to remove it from the car and carry out a visual inspection. If melting areas on the board or broken tracks are detected, the board should be replaced. If no signs of damage were noticed during inspection of the printed circuit board, it is worth “ringing” it. To do this, it is better to contact a qualified radio electronics specialist. If faults are detected during the “ringing” of the board, you can try to restore its functionality or simply replace it.

If no faults are found in the printed circuit board, it is worth checking the speedometer itself. It is quite possible that the pointer drive has failed. In this case, the speedometer is replaced.

There are cases when on a Lada Priora, checking the entire circuit responsible for the operation of the speedometer indicates that it is working properly. This means that the reason lies much deeper, namely in the gearbox. To fix this problem, it is better to contact the service. The speed sensor operates on the Hall principle, and if there is a malfunction in the operation of the gearbox, it will also be reflected in the operation of the speed sensor.

Malfunction in the instrument cluster

Often the speedometer stops working due to a malfunction of the instrument panel itself. The easiest way to check this is to temporarily connect a known working panel. It is also worth checking the reliability of the contacts on the back of the dashboard. You can also check the vehicle speed readings on the on-board computer.

If the dashboard was tuned (disassembled), then the arrow motor may have been damaged during the work, or the speed arrow is set too deep (the arrow touches the panel trim).

Have you encountered speedometer problems? How did you manage to solve it? Let us remind you that solutions to other faults can be found in the category repair and operation of Lada Granta, Lada Kalina or Lada Priora.

Share on social networks:

Found an error? Select it and press Ctrl+Enter..

Source

Checking fuses

Often the cause of a speedometer malfunction is a blown fuse. Most often, a fuse fails due to water getting on it, which flows onto the contacts, which leads to an interruption in the operation of the electrical circuit. If the check reveals that the fuse responsible for the operation of the dashboard has blown, then the car owner will simply need to replace it with a new one. Finding the right fuse is quite simple by marking “IG/METER”, but if the replacement process does not help solve the problem, then you will have to check the integrity of the wires that go to the dashboard from the speed sensor.

Speed ​​sensor on Priora: purpose and principle of operation

A speed sensor or DSA is needed to measure the speed of a vehicle. Such devices are also called speed detectors, which on Priora and other modern cars are presented in the form of electrical devices operating through a control unit.

Many drivers know that it is through the speed sensor that the speedometer on a car functions, but how the readings are recorded, few even think about it. If your DS fails, replacing it will eliminate the problem. However, knowing the operating principle of such a device will be useful for all car owners in order to be able to determine the reasons why the device failed and how to prevent such consequences in the future.

The speedometer needle jumps and twitches

In this situation, the diagnostic adapter will once again help us. It costs a penny, but with the right approach it often helps out.

The bottom line is that on cars with an engine management system, the signal from the speed sensor is supplied in parallel to the instrument panel and to the engine control unit (ECU). And in some cases, to the ECU, and from the ECU to the instrument panel.

Here I drew it in red for clarity

And as I always say, when we connect the adapter to the diagnostic connector, we begin to see everything “through the eyes of the computer.”

Therefore, it is no longer difficult to guess how to determine the direction of searching for the cause of the jumping speedometer needle.

A man is driving and watching the speedometer. I sit next to you and monitor the speed readings in the diagnostic program.

If the speedometer needle jumps, but the speed graph in the program is smooth, then the problem is in the direction of the instrument panel.

And if the arrow twitches, and the graph also has “dips,” then the problem is in the direction of the speed sensor and its drive.

This is exactly what happened in our case. These dips mean an unstable signal from the speed sensor.

This means that there is no point in going into the instrument panel. You need to move towards the speed sensor.

Diagram and pinout of DS Priora

Three wires are connected to the DS Priora plug. One of them is positive 12V, the second or central one is the signal wire that supplies impulses to the control unit, and the third is ground.

The speed sensor power supply circuit is shown in the photo below.

The DS pinout diagram on a Priora may be needed when replacing a plug or checking the incoming power.

What is the effect of a DS malfunction on a Priora?

All Priora car owners are familiar with the situation when the speedometer begins to act up. The arrow either shows the wrong speed value, freezes at some position or shows no signs of life at all. The reasons for this behavior are often related to the speed sensor. Such a device affects not only the operation of the speedometer, but also the engine.

If the speed sensor on the Priora is faulty, the engine will function, but the possibility of it going into emergency mode is possible when the fuel-air mixture is prepared at average values. Even on a Priora with electric power steering, if the speed sensor malfunctions, the power will not work (or work intermittently).

Let's immediately look at how the speed sensor affects engine operation. When the vehicle speed increases, the ECU understands that frequent fuel supply through the injectors is required. Naturally, the rapid movement of the car is also recorded by the level of throttle opening, for which the throttle position sensor is responsible.

If the car is coasting (downhill), then approximately the following picture occurs:

  • the speed of the car increases, as evidenced by the DS readings;
  • however, intensive fuel supply to the manifold is not necessary, since the ECU records the closed position of the throttle valve;
  • Thus, the ECU understands that the car is coasting, which means that fuel consumption at such a moment is minimal.

In modern cars, DS play a very important role, and if you could drive a carburetor car with a broken cable as much as you like, then on injection cars, where the DS is presented in the form of an electrical element, such a breakdown will entail an increase in fuel consumption, as well as interrupted operation of the engine . That is why it is very important, if such a malfunction occurs, to eliminate it as quickly as possible.

VAZ-2114 - searching for the cause of tachometer failure

To find out why the device in question does not work, diagnostics should be carried out. For this you will need a multimeter. With its help, first of all, ring the wire that supplies power to the VAZ-2114 tachometer, and then ground. This way you can easily detect a break in the electrical network. The tester should be set to ohms.

Before testing the circuit, make sure the multimeter is operating at up to 20 volts direct current.

Please note that the minus is always present in the circuit, but the plus appears only when the ignition is started. In this case, the tester will show pulses (regular voltage surges) if the crankshaft is spinning

During this process, be sure to inspect all connectors and make sure that the wires attached to them are held properly.

A blown fuse is the most obvious reason when the tachometer suddenly fails, and along with it they “die”:

  • odometer;
  • speedometer;
  • sensor that monitors coolant temperature;
  • fuel level indicator.

In this case, they function normally:

  • panel lighting;
  • indicators;
  • multimedia center;
  • optics;
  • ignition.

With such symptoms, you should first look at the fuse, indicated in the diagram as F3. Its location is the mounting block. Keep in mind that installing a new one without finding out the reason for the burnout of its predecessor is pointless. Most often the culprit is a short circuit. Experts have noticed that old VAZ model 2114 very often puzzles its owners with this breakdown after washing.

Even if you do not find a short circuit, do not rush to forget about the fuse. Check the condition of its connector. It may burn, oxidize, or become dirty. All this creates a high contact resistance, which overheats the fuse-link and contributes to its destruction.

Reasons for failure of the speed sensor on a Priora

As mentioned above, on a Priora the speed sensor is a pain. Moreover, its malfunctions do not appear after 100 thousand kilometers, but literally from the first days of operation of the new car. The reason for this is various factors:

  1. Oxidation of contacts - this phenomenon occurs due to a violation of the seal of the plug.

  2. Liquids getting inside - and although the sensor’s power supply chip (plug) is sealed, the possibility of oil and other aggressive substances (antifreeze, water) getting inside the connection cannot be ruled out.

  3. Damage to contacts - oxidized contacts simply fall off over time, breaking the electrical connection. Moreover, this happens even if the chip was not disconnected from the sensor.
  4. Violation of the integrity of the plastic housing - if the sensor housing is damaged, the product will not function.
  5. Damage to power cords. On Prioras, this phenomenon is very common, and if you determine that the sensor is working, then you should check the quality of the wires in the area where they enter the chip.

  6. The presence of dirt on the sensor body, which is a common cause of interruptions in the speed indicator. Small metal particles act as contaminants (production of gearbox gears). The particles are magnetized to the DS body.

Although the speed sensor on the Priora is relatively inexpensive (500-800 rubles), you should not rush to buy a new element. After all, the reason can only be contamination of this device or damage to the supply wires. That is why you first need to identify the cause of the breakdown, and only after that resort to eliminating it.

How to check and replace the sensor

This type of speed sensor is present in all VAZ cars

Check the continuity of the electrical circuit, because a break in it can lead to a malfunction of the DSA. Disconnect power. Inspect the contacts carefully. If there is oxidation or dirt, they need to be cleaned.

Pay special attention to the wires located near the plug, they are bent in this place and can fray the insulation

We measure the resistance in the grounding circuit. Should be 1 ohm. If the circuit and resistance are normal, we check the operation of the DS itself.

The Lada speed sensor, installed on all AvtoVAZ cars, operates using the Hall effect, i.e. one full revolution is equal to 6 pulses. It has 3 contacts: ground, voltage, pulse signal. We ring the contacts for the presence of grounding and voltage (12 V). If the voltage is absent or less than 12 V, it means that either the power circuit is faulty, or the battery is discharged, or the ECU is broken. The output-to-ground voltage should be in the range of 0.5-10 V. The easiest way to check the operation of the device is to replace it with a properly functioning one.

To remove the DS you will need: a flat screwdriver, a 10mm wrench (ideally a head with a ratchet). In a Lada Granta car, the sensor responsible for speed is located extremely inconveniently, so replacing it is quite difficult. To improve access, first disconnect the thick pipe going to the throttle body from the air filter. Then:

  1. Disconnect the power plug from the DS. Bend the plastic retainer and immediately pull the shoe up to remove it.
  2. Unscrew the DS mounting bolt with a wrench.
  3. Pry up the DS body, because it is tight, and remove it.

We install a working speed sensor in the reverse order and carry out diagnostics.

Some car enthusiasts advise that after removing the DS, carefully inspect it, dry it and apply sealant around its perimeter. After this, reinstall the sensor. But it is better, of course, to replace it with a new one.

For the information of car owners of cars equipped with ABS: on your Lada, the DS on the gearbox is disabled, and the speed is read from the anti-lock braking system sensors.

https://youtube.com/watch?v=AId86BbNqS0

Signs of a malfunctioning speed sensor on a Priora

The main consequence of problems with the DSA is interruptions with the speed indicator, or more precisely, with the arrow. It can not only be motionless, but also “act up”, namely:

  • indicate an incorrect speed value;
  • “freeze” at one value (not just zero);
  • twitch periodically.

The following types of manifestations may indicate a malfunction of the DS on the Priora:

  • The electric power steering does not work (on Priors with electric power steering);
  • The fuel level indicator in the tank does not work;
  • unstable engine operation, which is especially evident at idle;
  • loss of engine power and increase in consumption;
  • jerks when changing gears;
  • when coasting, the car may stall;
  • motor vibrations.

If the speed sensor is faulty, the Check Engine light may light up on the dash. However, the indicator lights up only when the pulses (signal) completely stop arriving at the ECU. This is why the indicator often does not light up, although there is a sensor malfunction. The following error codes may indicate that the DS on the Priora has failed:

  1. 0500 - no speed sensor signal. When such an error occurs, the “CHECK” light comes on.
  2. 0501 - DS error.
  3. 0503 - if the signal from the DS is interrupted.

Private situations

General signs do not always indicate specific breakdowns. There may be exceptions.

If individual devices refuse to work, it is quite possible that this is their personal problem. You'll have to parse the specific pointer. It may have a cracked gear that needs to be replaced.

Also, why doesn’t the instrument panel of the VAZ 2114 work? If the fuel gauge and tachometer are capricious (either they function, or they don’t react at all), the contacts and the mounting block are normal - you need to do a small check.

Reset is pressed and held, and the ignition is turned on at the same time. Raised arrows indicate the need for further searches. Lifeless - that microcracks have appeared in the shield itself. You will have to remove it and examine all soldering and traces under a magnifying glass. In principle, these are all the main options. If calling all the listed components and parts did not lead to the revival of the instrument panel, your case is individual, and you will have to determine the situation in the company of an experienced auto mechanic.

Where is the speed sensor on Priora?

An element such as a speed sensor is located on the gearbox housing, or more precisely, on the clutch housing under the housing of the internal joint of the right wheel drive. It is installed in this place on almost all car models. The photo below shows the place on the gearbox where the DSA is located on a Priora.

The photo below shows the place where the speed sensor is located on a Priora in the engine compartment.

No previous dismantling is required to access it for removal, inspection or replacement. It is better to get to it from the engine compartment (not from the pit), although this is not entirely convenient.

Characteristics of the control and measuring device

The Lada Priora has an electronic speed sensor (DS). Its design consists of a plastic housing, inside of which there is a sensitive element.

Location

In order to perform diagnostics, you need to know where the speed sensor is located. On the Lada Priora it is located in the upper part of the gearbox to the right of the exhaust manifold.

Functions and principle of operation

The main function of the DS is to determine the speed of rotation of the front wheels and transmit this data to the controller. Based on the information received, the controller regulates the quantity and quality of the fuel-air mixture that enters the cylinders. This data is reflected on the speedometer and odometer, which are located on the dashboard.

The operating principle of the device is based on the Hall effect. The DS transmits pulse signals of a certain frequency to the controller.

Errors and symptoms

You should know the main signs of malfunctions:

  • increased fuel consumption;
  • incorrect readings on the speedometer and odometer or their absence;
  • the engine is unstable at idle;
  • power decreases.

If the Priora speed sensor is faulty, it must be replaced immediately.

Which speed sensor to buy on Priora: types of products

Priora is equipped with three types of speed sensors from the factory. This is important to consider before purchasing a new product. To avoid mistakes, you should first remove the product and, having copied the serial number (you can take a photo), buy a similar option. This approach will ensure that you do not make a mistake with your purchase and buy the right type of sensor.

The second note when buying a DSA for Priora is to choose only original products. Chinese devices may cost 100-200 rubles cheaper, but they may not only not be suitable for installation, as evidenced by the photo below, but also not work correctly (or not work at all).

If you bought a DS, but during installation it fits tightly into the hole, it means that the product was chosen incorrectly. Compare the diameters of the standard and new products, and only then install the part.

In order not to make a mistake with your choice and buy an original DSA for Priora, you should pay attention to the presence of the serial number:

  • 2170-3843010-04;

  • 2170-3843010-02;

  • 2170-3843010.

The main difference between them is in the calibration (the type of signal perceived by the controller) and the shape of the working part where the semiconductor element is located. Choose the products correctly, as the correctness of their operation depends on this.

Features of replacing DSA on Priora: what is important and need to know

To replace the speed sensor on a Priora, you will need to arm yourself with a “10” key. It is recommended to use a ratchet or L-shaped wrench. You must first disconnect the power supply by pressing the latch and pulling it up.

After this, the nut is unscrewed to “10” and the DS is removed. You may need to pry it off with a screwdriver to remove it, as it has a sealing collar to keep the transmission sealed. The video below describes the detailed process of removing and replacing the speed sensor on a Priora.

It is important to note one point - when installing, it is recommended to treat the upper part of the device, namely the sealing element, with oil. This will simplify the process of not only installing the product in the hole, but also removing it back in the future.

It is worth noting once again that on Priors this is a sore when the DC power wires fray. If there is damage to the insulation, you should buy a new chip for the sensor and replace it. Do not try to wrap it with electrical tape, as this will not help. When replacing the chip, be sure to make sure not to mix up the wires. It is recommended to tin the junction of the wires with tin, and then insulate them with heat shrink, which will ensure a high level of tightness. Finally, you can carefully insulate the wires with electrical tape.

Having done it once and well, you will definitely not encounter a malfunction in the near future in the form of a failure of the speed sensor on the Priora. Take the DS replacement procedure responsibly to prevent such breakdowns in the future.

Source

Partial interruptions in work

This is where the speed sensor is located.
But it happens when the speedometer periodically refuses to perform its functions, and this is often accompanied by a failure of the electric booster, the fuel quantity sensor, and warning lights on the dashboard light up.

In most cases, this malfunction indicates a failure of the speed sensor. But before checking it, you should first check the pad contacts for oxidation.

Then you should remove the speed sensor itself. If severe contamination is noticed, then you should try to clean it and check its functionality again. If these actions do not bring positive results, the sensor should be replaced.

In most cases, carrying out the described operations leads to eliminating the speedometer malfunction.

Rating
( 1 rating, average 4 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]