The domestic car Lada Granta (in Russian Lada Granta) is equipped with a power unit with fuel injection. This configuration requires clear interaction of all sensors.
One of the most important controllers of the electronic system of this car is the speedometer. The article will answer the question - why the speedometer does not work on the Lada Granta. The principle of operation of the entire speed calculation system, symptoms of malfunction and causes of breakdowns will be considered.
Types of speedometers
There are currently three types of speedometers:
- mechanical;
- electrical;
- electromechanical.
On a mechanical type device, speed is transmitted from the gearbox using a cable. The distance traveled on the odometer is set by measuring the revolutions. Each revolution corresponds to a certain amount of mileage. The mileage traveled is reflected on the dial.
Mechanical device dial
In the electromechanical version, improvements have been made that eliminate the shortcomings of the mechanical device. The mechanical flaw was the cable, due to which the information was often incorrect. The electromechanical device is supplemented with a speed sensor, the signals from which are transmitted to the electric motor that rotates the gearbox.
All modern cars are equipped with an electronic device. The electronic speedometer measures the number of revolutions of the wheel. The mileage traveled is calculated by analyzing the wheel circumference and the number of revolutions. The information is reflected on the display.
Photo gallery “Speed indicators”
Possible device malfunctions: signs and causes
One of the reasons for speedometer and odometer malfunction is a broken cable. This can be detected by the characteristic sound that is heard in the area of the shield. After a break, the steel ends of the cable touch the sheath, and noise appears.
If the pointer is faulty, the needle either shows incorrect readings or it lies down and does not rise. The cause may be the speed sensor. If it is broken, you need to replace it.
If the speedometer on a Priora does not work, first of all you should check the fuses, they could have blown. In addition, you need to test the wiring and make sure the quality of the contact connections. If the device does not work, it must be replaced.
How to check the device for functionality?
Before changing or repairing the speedometer, you should find the reason why it is not working. First you need to diagnose the speed sensor, since it is most often the cause of the pointer not working.
First of all, you should inspect the regulator for mechanical damage. In addition, you need to check the integrity of the wires and the quality of the connections. In the event of electrical failures, a “Check” warning is usually displayed on the dashboard.
It is difficult to check the functionality of the controller board at home, since special equipment is required. You can check the condition of the gears. If there are nicks or chips, parts need to be replaced (the author of the video is Avtoelektika HF).
Basic faults
The Lada Kalina speed sensor can easily fail. Every car enthusiast can notice the problem. The main “symptoms” indicating the development of the problem are identified, including:
- lack of movement of the arrow (it just lies there);
- the pointer makes sharp jumps;
- the arrow freezes at speed even in the absence of movement;
- The electric power steering fault icon is on.
If the speedometer does not work, the most common reason for this phenomenon is a malfunction of the speed sensor. It is located on the gearbox, secured with one screw. There are three main wires connected to it. If it is a Lada Kalina with a 16-valve engine, you can find the device on the washer side. In the version with 8 valves, it is necessary to remove the bellows of the engine air filter.
To determine the device number, simply remove it and rewrite the numbers. There is no need to rush into buying a new part; first you need to check all contacts. In some cases, the malfunction is due to oxidation of the wires or damage to the wiring. Perhaps the problem is hidden in the presence of metal shavings or other particles.
Many experts have noticed that the malfunction of the speed sensor on Kalina is associated with problems with the electric power steering. If, after replacing the element, it still does not work, the device may be defective or unsuitable for the vehicle. Therefore, it is necessary to select it according to the assigned number.
Instructions for replacing the device yourself
Replacing the drive on Kalina is simple, you need to perform the following steps:
- Using a wrench, unscrew the screw securing the device to the gearbox.
- Next, use a screwdriver to carefully pry the hole and remove the speedometer.
- At the next stage, the removed drive should be inspected for defects and contamination. It is also necessary to check the seat and clean it of dirt.
- When inspecting, pay attention to the gearbox. If oil stains are found, the O-ring must be replaced.
- We install the repaired or new speedometer in its original place.
- We assemble the drive in the reverse order of removal.
After final assembly, the operation of the drive should be checked.
Repair
For convenience, the device is dismantled before repair. Further repair actions will depend on the cause of the malfunction. In some situations, the actuator or O-ring will need to be replaced.
Sometimes, if the speedometer has stopped working, it is enough to remove it, inspect it, clean it, dry it for some time and treat it with sealant around the perimeter. In most cases, repairs will require replacing the speed sensor.
What to do if the instrument panel fails?
If the speedometer on the Lada Kalina does not work, this may be due to a breakdown of the instrument panel. It is supplied to the automotive market only assembled, so it needs to be changed completely.
Before replacing, you should check the reliability of the fasteners that go to ground; this may be the cause of the breakdown.
The procedure for removing and replacing the instrument panel consists of the following steps:
- The steering wheel must be moved to the down position.
- Next, the mounting bolts are unscrewed.
- Then, overcoming the resistance of the latches, we pull the cover towards ourselves and remove it.
- Use a Phillips screwdriver to unscrew the center console mounting bolts.
- Having tilted the shield, we disconnect the connector with wires from it. To do this, you need to move the latch.
- We carry out the installation in reverse order.
The procedures for replacing the instrument panel and speedometer are simple and can be done independently. Thus, there is no need to waste time and money visiting a service station.
Malfunction in the instrument cluster
Often the speedometer stops working due to a malfunction of the instrument panel itself. The easiest way to check this is to temporarily connect a known working panel. It is also worth checking the reliability of the contacts on the back of the dashboard. You can also check the vehicle speed readings on the on-board computer.
If the dashboard was tuned (disassembled), then the arrow motor may have been damaged during the work, or the speed arrow is set too deep (the arrow touches the panel trim).
Have you encountered speedometer problems? How did you manage to solve it? Let us remind you that solutions to other faults can be found in the category repair and operation of Lada Granta, Lada Kalina or Lada Priora.
Keywords: instrument panel Lada Kalina | dashboard of Lada Granta | dashboard of Lada Priora
10
0
Video “Removing the instrument panel on the Lada Priora”
This video shows the process of removing and replacing the Priora instrument panel (the author of the video is “In Sandro’s Garage”).
To record the exact speed of movement, use the Lada Granta speed sensor (abbreviated as DS or DSA). It is located at the gearbox. Despite its small size, it is one of the main devices of the vehicle.
The Lada Granta engine management system is equipped with 7 main sensors: engine temperature sensor, oxygen sensor, speed sensor, as well as crankshaft position, phase, detonation and mass air flow sensors. The reliability and safety of the vehicle unit directly depend on the condition of these devices.
Principle of operation
Manufacturers have equipped the car model in question with an electronic speedometer. Such a system calculates speed as accurately as possible with a minimum percentage of errors. The system consists of the following elements:
- The speedometer itself is a completely electronic device with a minimum number of mechanical parts. It works using signals received from the on-board computer.
- An on-board computer, a device necessary for calculating incoming data.
- A system of electrical wires that provide power to the speedometer components.
- A fuse is necessary to protect against electrical overloads and short circuits.
- Speed sensor, the main element of the system. It is used to calculate the speed characteristics while driving.
So, next we’ll look at how the whole system works. Its main element is the speed sensor or EMF. The device operates on the principle of a Hall ignition and distribution system. The EMF is installed on the gearbox near the flywheel. The flywheel has a special risk. When this risk passes by the EMF, the contact inside the sensor opens. This creates an electrical impulse. As the speed of the vehicle increases, the number of such “openings” increases, which means more pulse discharges are created.
The pulses are sent through the wire to the computer, where the number of signals per unit of time is automatically calculated. Secondary confirmation comes in the form of pulses from the crankshaft position sensor. The on-board computer transmits the received data to the receiver - the speedometer drive. Depending on the magnitude of the received signals, the drive deflects the instrument needle by a certain degree.
The system is very reliable; it allows the on-board computer, based on the data received, to distribute the amount of combustible mixture into the engine, regulate the mixture of gasoline and air, maintaining optimal engine speed. Next, the symptoms of damage to the electronic speedometer of a Lada Granta will be described.
How to determine that the DS is faulty
The principle of operation of the speed sensor is as follows: there is a certain mark on the gear wheel of the gearbox that generates an impulse using the DS when the wheel rotates. The speed of the vehicle is determined based on the frequency of the received pulses. As the frequency increases, the speed of the machine increases. The signal from the speed sensor, as well as from many others, is displayed on the instrument panel.
The fact that the DS on the Lada Granta is located low indicates that it is strongly exposed to water, sand and dirt. This is the main reason for its failure. The following symptoms indicate that the sensor responsible for the speed of the Lada Granta car is faulty:
- the speedometer needle is at zero while driving or does not always work;
- unstable idling;
- The speedometer readings do not correspond to reality;
- fuel consumption increases;
- engine thrust decreases.
List of online stores, addresses of companies providing services
| № | Name | Contacts, address |
| 1. | STO "A1-Motors" | Moscow, st. 1st Dubrovskaya, 13a, building 4, phone: 8 (495) 120-15-38 |
Reviews of companies
- Vasily: six months ago I installed a servo drive on Grant at the A1-Motors service station. The guys did everything quickly and professionally. My recommendations.
- Ivan: after buying the Lada, I replaced the power steering with an electric power steering. I ordered the work from the service station “Auto Service on Sedova”. New equipment, many repair boxes, work professionally.
- Innokenty: comrades recommended installing an electric power steering system. I bought it at the Motel Varshavsky parts store. Good quality, reasonable prices, bonuses when purchasing.
- Vladlen: I drove the power steering for two years and decided to switch to the electric power steering. They advised to buy from Expert-Auto. Six months have passed since installation, no complaints, my recommendations.
- Vyacheslav: I’m leaving my positive review about the auto parts store “Spare Parts on Wheels”. Professional advice, reasonable prices, friendly staff.
How to check and replace the sensor
This type of speed sensor is present in all VAZ cars
Check the continuity of the electrical circuit, because a break in it can lead to a malfunction of the DSA. Disconnect power. Inspect the contacts carefully. If there is oxidation or dirt, they need to be cleaned. Pay special attention to the wires located near the plug; they are bent in this place and can fray the insulation.
- We measure the resistance in the grounding circuit. Should be 1 ohm.
- If the circuit and resistance are normal, we check the operation of the DS itself.
The Lada speed sensor, installed on all AvtoVAZ cars, operates using the Hall effect, i.e. one full revolution is equal to 6 pulses. It has 3 contacts: ground, voltage, pulse signal. We ring the contacts for the presence of grounding and voltage (12 V). If the voltage is absent or less than 12 V, it means that either the power circuit is faulty, or the battery is discharged, or the ECU is broken. The output-to-ground voltage should be in the range of 0.5-10 V. The easiest way to check the operation of the device is to replace it with a properly functioning one.
To remove the DS you will need: a flat screwdriver, a 10mm wrench (ideally a head with a ratchet). In a Lada Granta car, the sensor responsible for speed is located extremely inconveniently, so replacing it is quite difficult. To improve access, first disconnect the thick pipe going to the throttle body from the air filter. Then:
- Disconnect the power plug from the DS. Bend the plastic retainer and immediately pull the shoe up to remove it.
- Unscrew the DS mounting bolt with a wrench.
- Pry up the DS body, because it is tight, and remove it.
We install a working speed sensor in the reverse order and carry out diagnostics.
Some car enthusiasts advise that after removing the DS, carefully inspect it, dry it and apply sealant around its perimeter. After this, reinstall the sensor. But it is better, of course, to replace it with a new one.
It must be remembered that erroneous data from the Lada Granta speed sensor can lead to significant malfunctions in the operation of the engine and vehicle components.
For the information of car owners of cars equipped with ABS: on your Lada, the DS on the gearbox is disabled, and the speed is read from the anti-lock braking system sensors.
How to tighten the electric power steering rack?
The appearance of a knocking sound in the operation of the electric power steering is associated with the need to tighten the steering rack.
New Lada: Grant generator mount 8 valve
How to do it right:
- First you need to disconnect the battery; to do this, disconnect the terminals from it. Unscrew the battery mount; to do this, you need to unscrew two more nuts located at the edges. After this, the battery is removed and put aside.
- Then you need to lift the plastic stand, there are four more screws under it, they can also be unscrewed.
- Having done this, it is necessary to move this stand forward until the platform is disconnected from the air filter housing retainer pad. After this, the trim can be moved back, this will provide freer access to the rail itself.
- At the next stage, you will need to crawl your hand under the rail. Directly below it, as shown in the photo, there is a rubberized cap; it will need to be removed, this will allow the key to access the adjusting nut.
- To perform adjustment work, you will need a special wrench to tighten the rack; without it, the adjustment procedure will not be possible. Using this wrench, you need to crawl under the car rail to install the tool in the required hole.
- When adjusting, be careful not to overtighten the rack. If its tightening is very strong, then when cornering the rack will bite, and this, in turn, may affect the safety of movement. The angle of adjustment is always different, it depends on how much the nut is loose, but usually when performing such work the nut is tightened by approximately 30 degrees. This should be enough to get everything right. After the adjustment is completed, it will be necessary to check that this task was performed correctly. That is, you will need to make sure that the steering wheel turns normally to any position all the way and there is no knocking. If the knock remains, then the adjustment continues.
Lada Granta speed sensor: how to check and replace
To record the exact speed of movement, use the Lada Granta speed sensor (abbreviated as DS or DSA). It is located at the gearbox. Despite its small size, it is one of the main devices of the vehicle.
The Lada Granta engine management system is equipped with 7 main sensors: engine temperature sensor, oxygen sensor, speed sensor, as well as crankshaft position, phase, detonation and mass air flow sensors. The reliability and safety of the vehicle unit directly depend on the condition of these devices.
How to determine that the DS is faulty
The principle of operation of the speed sensor is as follows: there is a certain mark on the gear wheel of the gearbox that generates an impulse using the DS when the wheel rotates. The speed of the vehicle is determined based on the frequency of the received pulses. As the frequency increases, the speed of the machine increases. The signal from the speed sensor, as well as from many others, is displayed on the instrument panel.
The fact that the DS on the Lada Granta is located low indicates that it is strongly exposed to water, sand and dirt. This is the main reason for its failure. The following symptoms indicate that the sensor responsible for the speed of the Lada Granta car is faulty:
Please note that unstable engine idling and increased fuel consumption can also be due to a malfunction of the Lada Granta oxygen sensor, which consists of two devices: a control catenary collector located in the upper part, and a diagnostic one installed in the catenary collector behind the converter. They operate on the same principle and are interchangeable. The control oxygen sensor monitors the adjustment of the composition of the air mixture supplied to the injectors. The diagnostic oxygen sensor signals the presence of oxygen in the exhaust gases after the converter.
How to check and replace the sensor
This type of speed sensor is present in all VAZ cars
Check the continuity of the electrical circuit, because a break in it can lead to a malfunction of the DSA. Disconnect power. Inspect the contacts carefully. If there is oxidation or dirt, they need to be cleaned. Pay special attention to the wires located near the plug; they are bent in this place and can fray the insulation.
The Lada speed sensor, installed on all AvtoVAZ cars, operates using the Hall effect, i.e. one full revolution is equal to 6 pulses. It has 3 contacts: ground, voltage, pulse signal. We ring the contacts for the presence of grounding and voltage (12 V). If the voltage is absent or less than 12 V, it means that either the power circuit is faulty, or the battery is discharged, or the ECU is broken. The output-to-ground voltage should be in the range of 0.5-10 V. The easiest way to check the operation of the device is to replace it with a properly functioning one.
To remove the DS you will need: a flat screwdriver, a 10mm wrench (ideally a head with a ratchet). In a Lada Granta car, the sensor responsible for speed is located extremely inconveniently, so replacing it is quite difficult. To improve access, first disconnect the thick pipe going to the throttle body from the air filter. Then:
- Disconnect the power plug from the DS. Bend the plastic retainer and immediately pull the shoe up to remove it.
- Unscrew the DS mounting bolt with a wrench.
- Pry up the DS body, because it is tight, and remove it.
Possible breakdowns
Troubleshooting in the speed calculation system must be looked for in the electrical circuit. It is better to start work with the fuse.
Fuse
A 10 A fuse is responsible for protecting the instrument panel. It is located in the fuse block and is marked “F1”. It is necessary to remove the element and visually inspect for a break in the internal jumper. If there is no break, but there is melting of the case, then the protection device must be replaced with an exact analogue of 10 amperes. Additionally, you need to inspect the fuse contacts, eliminate any defects, and clean them.
After installing a new fuse, you need to check the circuit for electric current. To do this you need:
- Turn on the ignition.
- Set the multimeter to DC voltage measurement mode.
- Connect the red test probe to the fuse output.
- Black dipstick with ground.
The tester should show a voltage similar to the battery charge. It is prohibited to connect the power circuit directly without a protective device, through twisting, or to insert foreign metal objects between the contacts, as this may lead to a fire.
Sensor
If after replacing the fuse and checking the circuit, the problem with the speedometer does not go away, you need to check the speed sensor. This requires:
- Loosen the clamps securing the air purification filter pipe and remove it.
- Disconnect the EMF power plug.
Both halves of the connecting plug must be checked for dirt, oxidation, and broken contacts. Next, the voltage supply to this plug is checked. Necessary:
- Connect the red measuring probe to terminal “1”.
- Black probe to terminal “3”.
- Turn on the tester in DC voltage measurement mode.
- Start the power unit.
The tester should give a result of 12 volts. Such data will indicate the supply of voltage to the sensor terminals. If there is no voltage, then you need to determine the damage by inspecting the wires for a break. Any damage should be repaired by replacing the faulty wire.
Terminals “1” and “3” can be checked for resistance. Switch the tester to resistance measurement mode and connect the test probes to the indicated terminals. The operating resistance of the sensor varies between 3–10 ohms. Any deviations confirm a malfunction of the EMF.
After checking the incoming voltage, it is necessary to test the operation of the EMF. First, you need to inspect the device. If there are cracks, chips or complete breakage of the plastic housing of the sensor, it must be replaced with an exact analogue. If the case has no visible damage, then a performance test is carried out. To do this you need:
- Raise the drive wheel on a jack.
- Connect the wire from the “+” battery to terminal “1” of the sensor.
- Connect the ground wire to terminal “3”.
- Switch the tester to constant voltage testing mode.
- Connect the red test probe to terminal “2” on the sensor itself.
- Connect the black test probe to ground.
- Spin the drive wheel of the car.
The tester should show voltage that increases as wheel speed increases. The voltage is not stable, since it will be output in jumps due to the fact that the sensor creates pulses.
Similar testing can be done using a 9 volt light bulb. It needs to be connected in the same way as the tester. As the drive wheel rotates, the lamp will blink, increasing the cleanliness parallel to the speed of rotation of the wheel.
If there is no pulse voltage, the sensor will have to be replaced. This is not difficult to do. You need to unscrew the mounting bolt to “10”, turn the sensor slightly and remove it from its seat. When replacing, it is also necessary to change the spacer ring, having first cleaned its seat from oil and dirt. It is also recommended to insulate the sensor connector. This is done using silicone sealant.
Wiring
Often the cause of electronic speedometer malfunction is wiring. It needs to be inspected for the integrity of the insulation. Any damage must be repaired. Damage to the insulation leads to short circuits to ground. This happens especially often after washing the car or in damp weather. If there are broken connections or oxidation on the contacts, install new wiring or solder the old one with insulation of the connections.
Drive unit
There are 2 ways to check the operation of the drive. The first involves simply resetting the odometer. After resetting, the button must be kept closed and the ignition turned on.
The tachometer and speedometer needles must go from 0 to maximum and return to their original position. If this does not happen, then the reason lies in the device itself. Additionally, you can check by disconnecting the speedometer power plug. Next, you need to connect “+” from the battery to terminal “26”. The arrow should respond to a light touch with the wire by deflecting. If this does not happen, the problem lies in the drive - the receiver.
Also, the cause of the speedometer needle “freezing” may be a previous replacement or repair of the dashboard. Insufficiently deep seating of the arrow on the stem may cause it to touch the protective glass. Also, a deep landing may result in touching the scoreboard itself. Dismantling and reassembling the dashboard will help resolve the problem.
Where is the speed sensor on the Lada Granta: photo and price
Car: Lada Granta. Engine: 21116. Asked by: Damir.
Yesterday I came home, started climbing onto the curb and slightly hit the bottom of the car. And then it started. The speedometer needle began to dance, at first it seemed to me that it was even accompanied by music. Then it twitched at zero, twitched to 200, and fell again. No errors occurred; the engine warning light did not light up on the instrument panel.
She didn't get up again. I drove around the yard, looked smartly under the hood, and screwed in all the chips I saw. Did not help.
Knowledgeable people said that the speed sensor was broken, quite logical, but where is it located? I went to a car store to buy a new one to check, the store is good, they accept returns if there was no loss of presentation. And the seller told me that when the speed sensor breaks down, the electric power steering also doesn’t work, but for me it works.
Speed sensor location
An expert on Lada cars with many years of experience. I own a Lada Granta car, I collect cramps based on the Priora. Sometimes I stay overnight in the garage. My wife is more jealous of cars than of women.
The speed sensor on the Lada Granta is located between the BDZ (throttle valve unit) and the brake fluid reservoir.
Replacing the speed sensor
- The sensor can be removed by removing the air filter and inlet pipe.
Remove the pipe and move the air filter housing to the side
Nut 10 and the chip is removed
After you have removed the sensor, clean it; debris may have gotten on it. Since its body consists of a magnet, it could become clogged when it hits a curb.
New and old speed sensor
However, this is unlikely; most likely it has failed and requires replacement. But if there was dirt on it, then there is a chance that it is working. Put it back, connect the chip and test drive it to check.
Electric power steering failure due to speed sensor failure
Indeed, if the speed sensor breaks down, the electric power steering in some cars fails, and error P-0501 (Vehicle speed sensor signal outside the permissible range) should appear on the instrument panel. That's why the steering wheel refuses, so that the car understands that the sensor is broken. In your case, the nature of the failure said that the sensor shows zero speed.
Failure of the electric power steering may indicate a breakdown of the speed sensor!
Sensor price
A speed sensor costs from 300 to 600 rubles.
Lada Granta speedometer does not work - reason - Telegraph
Why does the speedometer not work on Lada Granta, Kalina or Priora?
=== Download file ===
Place an advertisement on the site. Lada Club News Shop Discounts Join the LADA 4×4 Anniversary Club! Password Registration Gallery Help Calendar. A couple of weeks ago strange glitches in the behavior of the car began. At times the speedometer stops working. At the same time, the electric power steering works at full power, the steering wheel becomes very light and not at all informative. Miracles also begin with the gas pedal, the acceleration when pressed is too sharp, the movement is jerky. After some short time, everything goes away on its own, the speedometer needle shows the speed, the steering wheel becomes heavier, the gas pedal behaves adequately. The STATE does not see any errors in this. As far as I managed to understand, when the speed sensor dies, the speedometer turns off and the power steering does not work at all. For me it’s the other way around. What else could be the reason for this strange behavior? The car is under warranty, but there is no point in going to the dealer, since the malfunction is not permanent, but rarely appears, but is quite unpleasant. Yes, most likely there is a speed sensor. It doesn't cost much money. DmDmT View profile Find more posts by DmDmT. Where is the speed sensor located? I have the same problem. Nikolay77 View profile Find more posts by Nikolay Oleg08 View profile Send a private message to Oleg08 Find more posts by Oleg The other day the same problem appeared. In the first minutes after starting, the speedometer worked, after which the needle fell and did not rise again. When I looked at the speed sensor, I immediately realized what the problem was. As a result, I pulled out the sensor, wiped it, dried all the contacts, put it back together and that’s it, the speedometer is alive again. I removed the sensor from above, nothing difficult, just a little inconvenient. Added after 1 minute Oh yes, I have a standard grant, the sensor is on the box. VOVAN View profile Find more posts by VOVAN I won’t say that this was a problem, but it’s kind of strange. Sometimes on a STANDING car, with the engine running at XX, the speedometer needle twitches, indicating a speed of about km. What could it be? Vitaly View profile Send a private message to Vitaly Find more posts by Vitaly. Added after 1 minute the same garbage. Vitaly, this happens to me sometimes when starting the engine. I think that there is no jamb in this. Oleg64rus View profile Send a private message to Oleg64rus Find more posts by Oleg64rus. Lada Granta 1. Same symptoms - problems with the gas pedal, the speedometer needle is at zero but the tachometer is fine, the EMI becomes too light. I also noticed that there is no sound signal for an unfastened seat belt, although the light on the dash is on. So what's the problem, the speed sensor? Happybox View profile Find more posts by Happybox. Theme options Printable version. View options Linear view Combined view Tree view. Headlights, lanterns, lamps, interior lighting, controls. Feedback – Official Lada Granta Club LADA Granta Club – Archive – Up. Page 1 of 2. Problems with the speedometer A couple of weeks ago, strange glitches in the car’s behavior began. Send a private message to STAS. Find more posts by STAS. SY Astyon, 2wd, diesel, automatic transmission Messages: Problems with the speedometer Yes, most likely there is a speed sensor. Send a private message to zver. Find more posts by zver. Problems with the speedometer Quote: Find more posts by DmDmT. Problems with the speedometer Hello. Find more messages from Nikolay Granta-Sport was an automatic transmission Messages: Message from Nikolay77 Where is the speed sensor, otherwise I have the same problem. Send a private message to Oleg Find more messages from Oleg Rostov-on-Don Gender: Problems with the speedometer The other day the same problem appeared. Find more posts by VOVAN Problems with the speedometer Hello everyone! Send a private message to Vitaly. Find more posts by Vitaly. Find more posts by victor victor. Problems with the Vitaly speedometer, this happens to me sometimes when starting the engine. Send a private message to Oleg64rus. Find more posts by Oleg64rus. Problems with the speedometer The same symptoms - problems with the gas pedal, the speedometer needle is at zero but the tachometer is fine, the EMU becomes too light. Message from zver Yes, most likely there is a speed sensor. Find more posts by Happybox. Your rights in the section. You cannot create new topics You cannot reply to topics You cannot attach attachments You cannot edit your posts BB codes On
Lada Granta why the speedometer does not work
I have a Kalina from the 10th year, I’ve already changed 2 sensors, they stopped working, I don’t have any chips, many people say that just remove the chips and the problem will go away, it didn’t help me, there are no chips, I had to install a new one
07.12.2017 – 23:21 Zhanar Davletova
I have a Lada 21901 about two weeks ago when a grinding noise appeared when the clutch was released at reverse speed, other speeds are on normally, please tell me what the reason is. year of manufacture 2013 cable clutch.
05.12.2017 – 13:09 Sasha Garkush
24.11.2017 – 21:14 Almas Kurmashev
I also changed the speed sensor at 30,000 thousand mileage
26.10.2017 – 03:23 Valera Kulik
the same crap happened, bought a sensor for Kalina2, installed it, it shows less, but it turned out that I had a Priorovskaya box, I had to take another one
10/14/2017 – 04:11 Valera Kulik
everything with the first numbers 1118 is a viburnum, and the rest of the numbers are similar, I encountered this too, on my viburnum there are 2 pillars Priorovskaya box with the first numbers 2170, and the rest are the same as with the Kolin sensor
04.10.2017 – 13:56 Yuri Meleshkin
Thanks for the video I replaced the sensor and the machine works correctly again
09/15/2017 – 12:24 Ilya Valinurov
The author easily and simply took out the sensor, but for me it barely came out, I suffered for two hours.
08/21/2017 – 21:08 Andrey Platov
Rocker box? I have a cable one, I poured oil through it when I changed it, there’s just no dipstick on the cable one, my sensor is small, the ball on the bottom looks different
08.08.2017 – 18:57 ertai usenov
Good afternoon, could you please tell me if I have a Lada Granta 2012, I lose speed when driving, I take my foot off the gas and put it back on, I continue driving, what is causing this, thanks in advance
07/22/2017 – 13:35 Vladimir Smir
Good evening. Tell me, where did you buy this computer?
07/19/2017 – 05:41 Uraxa 32
For e-gas, even if you remove the plug for a month, the error will not go away. The ECU is designed differently; it has energy-independent memory. forget about the terminals.
06/30/2017 – 02:04 Andrey S
changed 5 dachas in four years
02.06.2017 – 10:15 Erbol Taldybaev
Good evening, I have a grant of 14 g, mileage is 38 thousand, the speed shows that no, it writes an error of 500, tell me, beaver people, what’s going on
05/08/2017 – 14:31 Viktor Sankov
Very good and useful video. My Lada's speedometer doesn't work either. I will repair it the same way. Thanks to the author of the video.
04/16/2017 – 18:36 Viktor Sankov
I have a question for the author of the video. When you remove the sensor, you first need to separate the electrical wires. How to remove the wires? Just pull them up or something else? there is a bracket or some kind of clamp, what should I do with this figurine? Explain, please.
04/14/2017 – 10:45 Alexander Glazkov
04—manufacturer -Kursk, 02—manufacturer Kaluga, don’t look at the numbers at the end, but just look for the Prior sensor. Don’t repeat my mistake, I walked around half the city looking for exactly the same sensor as the one I had. In the end, I bought the exact same one, and it’s from Kalina. It didn’t fit - the number of pulses is 3 times less, the speed shows accordingly.
04/05/2017 – 11:38 Azamat Karatayev
Hello Alexander, please tell me what signs you had when the sensor broke down? By the speedometer?
03/22/2017 – 01:22 Azamat Karatayev
Thank you It’s just that the EUR failed for me too. I think that’s where my legs grow too
02/20/2017 – 03:21 Alibek Kozhanov
Hello Alexander, my speedometer sensor fell off, I bought it without diagnostics and put it back in place
