How to disarm the standard alarm system on a Priora?

Cars from the Volzhsky Automobile Plant traditionally belong to the risk group, theft of which is quite likely. This statement was equally true for “classical” models, and it is also true now.

At the same time, installing an expensive car alarm on an inexpensive car can hardly be justified. Therefore, many owners are quite satisfied with the standard alarm system that was originally installed on the car. For example, a standard alarm system on a Priora will be able to provide minimal protection against theft and will not require additional costs.

It should be borne in mind that a potential thief (or vandal) first of all pays attention to cars that, upon first inspection, do not have any means of protection. If the owner, when leaving the car, traditionally locks it with the key, and the car itself does not greet its owner with blinking direction indicators, does not react to a blow to the wheel, or does not have a simple flashing light indicator, then such a car becomes an easy prey for scammers.

Why do you need to turn off the alarm?

The need to suspend the machine's security device is dictated by emerging circumstances. The main reason when you need to turn off a car alarm is its failure. The alarm may need to be suspended at any time. The device is turned off using a key fob or a special button with your own hands. Drivers’ knowledge of the shutdown procedure is a necessity dictated by emerging situations.

The car alarm stops functioning in a number of cases, then you need to turn it off. Alarm failures occur for the following reasons:

1. The security device is exposed to high-level radio interference. Car owners in large cities are especially affected. Interference with key fob signals comes from numerous electronic devices, power lines, and power electrical installations. The signal from the car alarm key fob increases as the distance between the transceiver devices decreases.
2. It's rare, but sometimes the car alarm key fob breaks. The situation cannot be ignored, just like when the batteries are dead, you need to turn off the security system. In this case, everything must be done with your own hands when there is no battery at hand.
3. Complete discharge of the car battery is one of the main reasons for the alarm to stop working, which is recommended to be turned off. In this situation, you should strictly follow the recommendations of the car alarm instructions.

These are the main situations when it is necessary to terminate the security device. Other emergency situations are possible that require the intervention of the car owner.

Why are there no friends

Even the most shy and unsociable introvert needs a friend. At least in one. A best friend is a person who knows you well, is always ready to help, and is fun and cool to spend time with.

The older a person gets, the fewer real friends he has. After all, often the strongest friendships we have are with those whom we met in childhood, grew up and matured together. And then different situations happen in life when we find ourselves alone without our usual social circle:

• moving to another city or country;
• loss of contact with old friends due to the fact that you have families and do not have enough time to communicate;
• you just want to change your current environment because you have outgrown the level of your friends;
• your “other half” categorically does not like your friends or girlfriends.

This is not an exhaustive list, but whatever the reason for your loneliness, you can always meet new people who can become friends.

Principles of disabling car alarms

The car alarm can be turned off in two ways. To disable the standard alarm, it is recommended to use the factory method. To disable it, use the “Valet” service button. This is only possible if you know where it is located, located in secluded but accessible places:

• Directly at the gas or clutch pedals;
• In the area of ​​the fuse box;
• In the niches of the steering column;
• In accessible places on the front panels.

If it is impossible to identify the button in the indicated places to turn off the car alarm, experts advise referring to the instructions. For alarm management, this information is key and must be contained. To disable, use a combination of simultaneously pressing the buttons and one of the pedals or two.

If you fail to turn off the car alarm after several attempts, it may become blocked. The recommended time for holding the alarm button with the pedal pressed should be at least 10 seconds.

The next technique is a coded shutdown, without using a car alarm key fob. Modern devices use button and ignition combinations. Disabling steps can be done manually using several techniques. Details on how to turn off the machine alarm are described in the attached instructions for setup and operation.

This option uses a PIN code that is programmed in advance. The combination of symbols is known exclusively to the car owner. The PIN code is programmed with the ignition on and successive pressing of the emergency button. The number of times the button is pressed corresponds to the first or second character of the code.

When setting a PIN code for car alarms with your own hands, the maximum code value of 4 digits is allowed - 9999. In standard alarm systems supplied by manufacturers, the PIN code is not complicated. It is not difficult to disable the car security system. Therefore, experts recommend reprogramming the code using a much more complex combination of symbols. Linking to memorable dates is not recommended.

There are alternative options to disable the car alarm. One of them is the use of original software. In another, special crawlers are used to disable the alarm.

Notes on implementation of schemes

Let us immediately note: if there are no window lifters, the second diagram will not contain parts K2/K3. Then you only need to cut one wire. Sometimes only the rear windows are missing. This means that relay K3 is excluded. And the diodes connected in parallel with the winding can be absolutely anything.

Now we list the requirements for an element called “relay”:

1. Operation voltage – 12 Volts;
2. Switching current – ​​10 A or higher;
3. The current consumed by all relay windings should not exceed the value specified in the instructions for the signaling. Usually it is 200-300 mA.

It is the last requirement that is often violated.

In order for “scheme 2” to work, it is necessary not only to assemble it, but also to program the main unit: you need to enable the “2-step unlocking” option. And be that as it may, control impulses cannot be made too long. Use values ​​of 0.7-1.1 seconds.

Power cables (cord X1-6) can only be connected using twists.

The cross-sectional area of ​​the wire must be sufficient to withstand a current of “10 Amps” (this does not apply to signal circuits). A fuse protecting the power circuits must be installed. And of course, before installation, remove the negative terminal of the battery.

Disabling without key fob

Disobedience to a car alarm key fob is a rare precedent, but it does happen. The main reason is that the alarm system was assembled and installed with defects that appear over time. The car owner is faced with a dilemma - it is necessary to disable the security device without a remote control. This part of the text is devoted to turning off the system without using the control panel.

The reasons for disconnection can be indirect and objective. Indirect ones include inhibited actions of the key fob that occur due to wear of the remote control battery or accumulator. It is recommended to avoid using the remote control away from the machine.

Another reason when it is impossible to turn off the alarm is that the car battery is discharged. In this case, the owner takes measures to bring the battery into working condition. Next steps are taken with the car alarm.

Objective reasons include worn-out car alarms. In such cases, turning off the device is very problematic. To turn off the alarm, it is advisable to gain access to the service button, or try to turn off the power to the system.

Another reason is that the remote control has lost synchronization with the protection device. The problem can be solved by flashing the remote control yourself, according to the instructions, after first using the emergency opening of the car. How to turn off the alarm in an emergency was discussed above. In any case, there are two main options: car alarm emergency button; using a PIN code.

You shouldn’t give in to panic if you can’t turn off the car alarm at the right time. First of all, you need to remember the recommendations of the alarm operating manual. It is possible to disable it without a key fob, either with your own hands or with the involvement of service organizations. Access to the car interior is always possible.

Sensitively responding to market demands, automakers have created a special anti-theft system that is installed on the car directly on the assembly line. The Priora's security is asleep until it is activated by the owner. This is an immobilizer, or as it was called even more simply - an immobilizer, a standard alarm system of modern cars.

For M-73 the process will look simpler:

Installing the OpenBox program and the HxD file editor on your computer. Connecting the immobilizer to the computer via an adapter, the standard EEPROM code is read. The code is saved. Open the saved code in a file editor and add the first line with the text: FFFFFFFFFF. Save changes. But such a file can be searched on the Internet. Load the edited code into the immo memory through the program. Disconnect the module and install it in the car. Disabling the immobilizer using a crawler

It is easier to disable the immobilizer on a Priora yourself using a device - an immobilizer crawler for a Priora (most often they are produced by Starline). To do this you need:

Find and disassemble the immobilizer unit in the Priora. Before disconnecting from the network, connect to the computer via an adapter. Resolder the resistor chip to modify the blocker control module. Run Eeprom and Flash diagnostics, save existing versions. Install the “untrained” program in place of the old one. Solder the resistor chip. Deactivate the anti-theft system. To do this, you can change the ignition switch in the Priora to “update” the immobilizer. It’s just that the immobilizer training key will not be used in the future. Disabling the immobilizer without using a crawler

These methods have already been described and they are more reliable because they completely change the firmware of the device and provide a guarantee that the immobilizer will no longer break and will not leave the car owner in the cold. Using a waste module may be an innovative way, but it only masks the problem, not eradicates it.

The standard alarm system on the Lada Priora consists of the following links:

1. Control unit – connected to the glass unit control system;
2. Communication coil – installed in the ignition switch;
3. Main and demonstrative keys, which are equipped with a buzzer and contact keys;
4. Central key on the dashboard;
5. The control unit is located on the right side of the brake pedal. It has several connection points.

Priora standard alarm or immobilizer

In order to prevent car buyers from tampering with the elements of the car system, they did not install anti-theft alarm systems from third-party manufacturers, and developed a standard alarm system - an immobilizer. This system differs from all other types of security alarms in that it interacts directly with the Electronic Engine Control Unit (ECM) of a modern car. When a car leaves the factory, this computer, the electronic control unit (ECU), contains a special EEPROM security file. Only a coded signal from the APS unit (automotive anti-theft system) can turn it on. She sends this signal only after the activation procedure. After this, when activated, it becomes a full-fledged automobile anti-theft system.

Installation map for Starline A93 Can+Lin car alarm for Lada Priora Lux 2014-15 manual transmission

1. To access the ignition switch connector, remove the lower part of the steering shaft housing. To do this, you need to remove the plastic trim under the steering column, releasing the clamps, then remove the lower part of the casing (fastened with three self-tapping screws and two screws).

Steering shaft housing. General form

Plastic lining fasteners

Plastic cover removed

Self-tapping screws and screws for securing the steering shaft housing

The lower part of the steering shaft housing has been removed

2. To access the VSM unit, remove the left side trim of the central tunnel (fastened with one screw). Then remove the VSM unit (mounted with a bolt and nut).

Self-tapping screw for fastening the side trim

Side trim removed

Bolt and nut for fastening the VSM unit

VSM block removed

3. Install the antenna module with built-in shock and tilt sensor on the windshield, LED on the left pillar. Install the service button covertly in any convenient place.

Possible location for installing the antenna module

LED installation location

4. Install the siren under the hood (attach it to the nut) and the engine temperature sensor (using plastic ties). Route the wires into the passenger compartment through the standard seal on the left side of the engine shield.

Possible siren installation location

Siren installed

Engine temperature sensor installation location

The temperature sensor is fixed to the pipe using ties

Standard seal. View from the salon

5. Secure the StarLine A93 central car alarm unit to the right above the BCM unit.

An example of the location of the central car alarm unit

6. Connect the StarLine alarm ground at the bottom left under the VCM unit under the standard nut.

7. Connect the CAN bus and LIN bus StarLine in the harness of connector 3 of the BCM unit.

Conventional numbering of connectors on the VSM unit

CAN bus (yellow-red, pin 16 and gray, pin 15)

LIN bus (blue-white, pin

LIN bus connection

8. Connect the trunk limit switch in the harness of connector 3 of the BCM unit.

Trunk switch (yellow, pin 14)

Connect the hood end switch in the harness of connector 2 of the BCM unit.

Hood switch (white-black, pin 15)

Connecting the hood and trunk limit switch

9. In the harness of connector 2 on the BCM block, connect an alternative control of light signals (black and white wire of connector X3 of the Starline alarm system).

Light signal control (red, pin 5)

10. To bypass the standard immobilizer, remove the battery from the key and place the key in the StarLine BP-03 immobilizer bypass module. Then connect the bypass module to any wire of the standard antenna on the ignition switch.

Standard antenna wires (green and white)

11. In the ignition switch connector harness, connect the engine starting power circuits, power supply to the security system and the autostart power module.

Ignition (blue-black)

Starter (red)

Power + 12V (brown)

12. Program the security and service functions of Starline A93 (see installation instructions, section “Main menu for programming car alarm functions”, Table 1).

13. Program the vehicle starting parameters (see installation instructions, section “Main menu for programming car alarm functions”, table 2).

14. Adjust the sensitivity of the shock and tilt sensor (see the installation instructions, section “Connecting the transceiver (antenna module) and setting the shock and tilt sensor”). Factory sensitivity values: warning level of the shock sensor - 10, alarm level of the shock sensor - 5, tilt and movement sensor - 5. After setting, check the operation of the sensors, if necessary, repeat the setting procedure.

15. Check the operation of the Starline A93 car alarm. Reassemble the interior in the reverse order.

What does the standard Priora alarm system consist of?

Any standard anti-theft system consists of several elements, it includes:

• training key;
• key fob;
• signal receiver antenna;
• APS block;
• lock activators;
• sound signal;
• EEPROM section in the ECU.

Training key (transponder)

The key set includes two ignition keys. One of them is the so-called educational one. It has a built-in special semiconductor chip with characteristic magnetic radiation. It is inserted into a special recess in the end part of the key, closed with a red decorative cover. Because of this, such a key is sometimes called a red key. This element is necessary to activate the standard anti-theft system. And for using the car if the anti-theft is not activated.

Key fob

This ignition switch has a key fob built into the handle for a standard alarm, just like a regular car alarm. It has only three buttons:

Accordingly, when the APS is activated, each button performs its own function.

Signal receiver antenna in the ignition switch

To read signals from the training key and key fob, a special antenna is built directly into the ignition switch. It is made in the form of a kind of coil, and is connected to the APS electronic control unit. Its task is to read the key signal and transmit it to the block.

APS block

This is an electronic unit that receives a signal from ignition keys equipped with a chip, or key fob, and gives a command to the car’s computer, which controls the entire ECM system and allows starting and driving, via a special channel. In addition, the APS standard alarm unit transmits signals to the activators of the door and trunk locks, and an audible signal to sound an alarm. On the Priora, the APS unit is built into an additional electrical package control unit, that is, a unit that controls power windows, heating and rotating rear-view mirrors, and other additional devices.

Lock activators and sound signal

These devices (activators) in the standard Priora alarm system operate as a central lock, that is, when the driver's door is closed with the key, the latches of all doors are closed. They are in a locked position and cannot be opened by simply pressing the handle. Their principle is ordinary electromagnetic coils that move the lock lever, closing all doors upon a signal from the control key fob.

The usual type of sound horns are connected under the front bumper of the car.

EEPROM file

Just an area in the flash memory section of the control ECU. Upon receipt of a certain message, it is activated in the recorded program. From this moment on, all actions: starting, moving away, central locking are possible only with an activated key fob and a training key. Otherwise, this file blocks operation and turns on the standard Priora alarm system.

What causes a car security system to break down?

As we have already said, a car alarm is a technical device. It consists of various parts and elements that become faulty and wear out over time. There are often cases when problems develop at the most inopportune moment. In this case, the driver has to be pretty nervous.

Now let's make a small digression. It is important to understand here that the quality operation of any technical device depends on a number of factors. What do you think we're talking about? Of course, about timely maintenance and care of the components of the anti-theft system.

Premature, spontaneous malfunctions may be due to the following reasons:

• Insufficient battery charge of the control panel;
• Mechanical wear of the button surface of the remote control;
• Oxidation reactions occurring at the location of conductive parts;
• Broken power transmission to the ECU;
• Blown fuses.

The reasons have been found out. How to solve the problem? If it's the battery, then everything is simple - replace it. Worn keys are a common and common occurrence. You can return the remote control for repair or simply buy a new one. In the latter case, you will have to register the key fob in the program. Most often, the keys for opening and closing doors are erased, because they are used more actively.

As for oxidative reactions - how do they occur, why? This happens if the integrity of the key fob is damaged and moisture gets inside it. But this can happen if the remote control falls into a puddle - no one is immune from such incidents. Take the keychain apart to let it dry. If there is no short circuit, the dry remote control will work. If not, replacement is necessary.

Activation of standard alarm

When leaving the factory, the car anti-theft system installed by the manufacturer can be said to be asleep. In order to “wake up” it, or more correctly, activate it, you need to go through a special procedure for activating the standard alarm. This can best be done, of course, by a specialist at a service center. But in principle, this procedure is available to the owner of the Priora himself. You just need to write down the action algorithm on a piece of paper, prepare two keys, a training key and a key fob, get behind the wheel with all the doors tightly closed, and carry out the operation strictly step by step.

1. Use the red learning key to turn on the ignition for 6 seconds and then turn it off.
2. The warning lamp in the form of a key on the instrument panel begins to blink rapidly, about 5 times per second. It will flash all the time during the learning process. If the lamp stops flashing before the end of the process, it means an error has occurred and you need to start again.
3. Before 6 seconds have passed, with the ignition off, remove the red key and insert the immobilizer key fob.
4. Turn them on the ignition. If everything is in order, the panel buzzer will give 3 signals at once.
5. Wait another 6 seconds with the ignition on. The buzzer should croak 2 more times in a row, and you can turn off the ignition. Wait until the light on the panel goes out without removing the key from the lock.

Lada Priora Sedan “S line” › Logbook › DIY installation of Starline A91

The other day I installed a STARLINE A91 alarm system on my car. It took me two days, 6 hours each, to install it. But I still spent a lot of this time on debriefing - what, where and how to connect. I read a lot of blogs and decided to write short instructions for installing such an alarm. Let me clarify right away that I did not connect the trunk opening button and the engine blocking relay to the alarm, and I also did not do step-by-step opening of the doors. Let me jump ahead - only four wires need to be cut completely (to the central locking in the door, to the starter, to the standard immobilizer bypass and to the handbrake), we simply connect the rest in parallel.

PS I didn’t take any photos during installation because... I didn't see the point in this.

To begin with, I purchased: 1) corrugated cables. It took me about 6 meters, because... I hid all the wires in it. (the length depends on where you will have the alarm unit)2) electrical tape3) 4 1N4007 diodes (if not included with the alarm)4) wire. (also depends on where the signaling is installed, because the length of some wires is not enough) 5) a standard immobilizer crawler (in which we put the chip) 6) a lot of patience. After all, you’ll have to crawl on your knees under the steering wheel and there’s not too much space there))))

Now briefly about the installation: 1) remove the fuse box cover

5) unscrew the BUS with a 10mm wrench. It is held on by two bolts. I only needed to unscrew one side and I pulled it out.

6) we put the antenna on the windshield 7) I embedded the light bulb into the trim of the left pillar

The shock sensor is written that it needs to be placed on the body and so that there is access to it for adjustment, but I did not find such a place and placed it to the right of the fuse block on plastic. 9) we hide the service button somewhere but so that you can reach it while configuring the alarm .10) from the engine compartment we pull three wires from the signaling system from the 18-pin connector - orange-gray, black, grey. Gray is the plus for the siren, we connect the minus from the siren to the body. Orange-gray and black we connect to the temperature sensor that comes complete with signaling I bolted the temperature sensor to the engine. We also additionally connect the orange-gray wire to the hood end switch (to the white-black wire) 11) and from the 18-pin connector we pull two wires into the instrument panel - gray-black, orange-violet. Gray - we connect black to brown-white (this is a generator), and orange-violet to brown-blue (this is a handbrake) according to the diagram. (The diode must be connected exactly according to the diagram. The diode designations are present in the picture)

PS later redid the control of engine operation using the tachometer because there were problems with reading the generator. In general, the gray-black signal wire should be connected to the brown-red one in the instrument panel and in the signaling settings, control the engine operation using the tachometer.

12) We cut the loop of black wire from the 18-pin connector if you have a manual transmission 13) We lay two wires from the 6-pin connector of the central locking alarm into the driver's door - green and green-black. connect it to the brown wire near the central locking unit. make connections according to the diagram below

Also note that the blue wire needs to be connected to the green one, and the black and red wire must be cut and one end (which goes to the unlocking relay) connected to the car body

source

How to turn off the standard alarm

It is very important to know that if the factory anti-theft is activated, it is simply impossible to disable it yourself. The file, having revived, will no longer fall asleep. The only civilized way to deactivate an armed and trained alarm is to remove the ECU from the car and either replace it with a new one that is not trained, which is very expensive, or give it to specialists for reprogramming. It is many times cheaper and more reliable. There is also a popular way to “deceive” a trained unit - when the chip is removed from the training key and taped with tape at the base of the ignition switch. However, it is worth remembering that this is a rather clumsy and risky method. The risk of failure of the Priora standard alarm program increases and, accordingly, there is a danger of its unauthorized activation at the most inopportune moment. Therefore, if it is activated, then it is better to use it, especially since user reviews about it are very good.

In the video you can watch the training process of APS “Priors”, “Kalina” or “Grants”, with two working keys:

Review of the standard alarm system on Priora

Cars from the Volzhsky Automobile Plant usually belong to the risk group of cars, theft of which is quite possible. This statement was equally correct for the “classical” models, and it is also correct at the moment.

At the same time, installing an expensive car alarm on a cheap car can hardly be justified. Therefore, many owners are completely satisfied with the standard alarm system that was installed on the car at the beginning. For example, the standard alarm system on a Priora will be able to provide the least amount of protection against theft and at the same time will not require additional costs.

It should be noted that a possible thief (or vandal) first pays his attention to cars that, upon first inspection, do not have any means of protection. If the owner, when leaving the car, traditionally locks it with the key, and the car itself does not greet its owner with blinking direction indicators, does not react to a blow to the wheel, or does not have a simple flashing light indicator, then such a car becomes an easy prey for scammers.

Reliability level

Undoubtedly, the standard alarm system installed and configured on the Lada Priora is simple, reliable and fully adapted to difficult local weather conditions. Properly activated, it leaves no doubt about its functionality. Besides:

Unfortunately, if the factory, standard installation is a big plus of such an alarm, then at the same time it is also a significant minus. Thousands of analogues of such alarms drive Lada Prioras across the vast expanses of the country. No mystery for attackers. But they are not looking for cars with alarms, but without them at all. You also need to understand these immobilizers, and time is money. And unnecessary problems are not for the criminal business.

What to do if Priora is not removed from the standard alarm!

The hazard lights are blinking, the car does not respond to the ignition key buttons. As a rule, several blocks are involved here, which are synchronized with each other.

1. Ignition
2. Radio channel module (Located in the driver's door)
3. Electrical package block (Comfort block)
4. Engine ECU

New blocks come with non-activated codes inside and can be installed on any car without problems, but once you register (train) the keys, a special code is written into all these blocks, which is synchronized with each other and serves as a standard alarm system. (Immobilizer) As soon as you turn the ignition key, within five seconds there is a poll between the key and the units, if the code matches everywhere, then the engine ECU gives permission to start, if the code of at least one device is not recognized, the engine ECU is blocked and the car does not start.

The working key is trained using a special red training key. I will not describe the procedure for learning keys; there is plenty of information on the Internet. In fact, the main key is the red training key; it stores a code that, after training, is written into the working key and other blocks.

Alarm characteristics

After modernization, the Lada Priora received a device that plays the role of a basic alarm system and received the usual name for such devices - an immobilizer. An immobilizer (from the Latin to paralyze) is a device that, interacting with the electrical control unit, allows you to shut down the operation of the engine and provides unhindered access to the car and its systems.

By its very nature, the immobilizer security device presents itself in such a situation as a breaker of the electronic circuit that powers the car. And the driver, who has an active key with a microchip built into it, activates (turns on) or disconnects the power supply chain if necessary.

At the same time, installing the key in the ignition switch socket is not a connecting link, but only allows you to send a signal to the necessary electrical sensor so that the necessary devices do their job. Structurally, the immobilizer protective device consists of several blocks that are connected into a single mechanism:

Principle of operation

The principle of operation of the standard Priora alarm, like any other, with reliable dynamic coding, is quite simple and understandable. The activated signaling system accepts for execution exclusively the commands of the native, trained chip installed in the ignition key of the Lada Priora. This will be followed by a series of logically related actions:

• the communication coil, having received a reliable encoded signal from the ignition key chip, forwards it to the standard immobilizer (IMMO) of the Lada;
• he, in turn, checks the received reliable, encoded signal with the code recorded in his memory;
• if they match, the immobilizer sends a command to the authorized engine start of the Priora ECU;
• The Lada ECU, having received a signal from the IMMO alarm, unlocks its electrical circuits;
• If there is an unauthorized attempt to start the Priora engine, the IMMO will not send a confirmation signal to the ECU and the control circuits will not be unlocked. In addition, a siren warning signal with light flashes will sound;
• in addition, the car key fob, built into the chipped ignition key, controls the central locking of the Lada Priora and its window lifts;
• By installing shock or volume sensors yourself, the alarm system receives an additional option to increase its reliability.

Important: be sure to require activation of the standard Priora alarm system when purchasing it. Otherwise, you will have to configure it yourself using a training key with a red insert. In this case, various nuances with its performance are possible.

Alarm activation

In order to activate the standard alarm, you will need a training and master key, which must be issued when purchasing the car. Be sure to pay attention to this, or in the future you will have to contact the dealer separately. You will need to carry out the following actions in the prescribed manner:

1. Fill the fuel tank (at least 10 l). This action must be performed so as not to get confused in the signals supplied by the immobilizer and to carry out the sequence of operations in strict accordance with the algorithm.
2. First of all, you need to use the learning key, which is inserted into the ignition switch. The ignition must be turned on for a certain time (about 6 seconds), and all doors in the car must be tightly closed. Correct actions can be monitored by a rapidly flashing (about 5 times per second) indicator lamp. After this, you can turn off the ignition and remove the learning key from the lock.

Protection functions and operational reliability

The standard Priora alarm system is not overloaded with additional functions. It does not have access to service options related to auto start, opening the trunk, or searching for a car in a parking lot. It will not inform its owner based on the indication from the key fob about the loss of communication with him. And even more so, it will not send all kinds of SMS messages about various machine malfunctions. Let the owners of Bugatti Veyron and Porsche 918 use GSM communication and GPS navigation services.

It is absolutely not worth using a gas adjustable wrench No. 3 as a torque gauge. The standard Lada car alarms have a different task. They don’t need to amaze the Priora owner’s colleagues with the ergonomics of the control key fob or autostart from a neighboring village. Their advantage is reliability and ease of setup without additional hassle and the involvement of related specialists. In addition, during its operation, the standard alarm system ensures the safety of specific areas of the machine:

• doors of a protected vehicle;
• car hood or trunk door;
• driver's door with lock cylinder;
• voltage at the terminals of the standard battery.

Lada Priora will give a fairly reliable alarm signal and will accompany it with flashes of turn signals when attempting to violate any of the zones protected by the standard alarm system. Such unauthorized access attempts include:

• desire to open any of the car doors, including the trunk or hood;
• turning an untrained key in the ignition lock of the Lada;
• any manipulations with the standard battery related to its connection or disconnection;
• when an additionally configured volume or shock sensor is triggered.

Important: if cases of incorrect operation of the car’s standard alarm system occur, you should first of all check the serviceability of the control key fob.

How to turn off the standard alarm?

The main reason when it is necessary to disable the standard alarm on a Priora is its malfunction. In such situations, the car unreasonably reacts by turning on the sound signal and prevents the engine from starting. Such a failure in winter conditions poses additional inconvenience. The immobilizer is not only an additional constant consumer of energy, but may simply refuse to work normally in severe frost.

At the first sign of incorrect operation, you should check the serviceability of the alarm control unit on the key fob. Perhaps the poor response to the signal from the key fob is due to a dead battery or the presence of radio interference in a certain place. In such situations, the control unit will only be able to receive a very close signal.

The inability to turn off the standard alarm system on a Priora from the key fob is not an obstacle to turning it off. In this case, you need to use a secret button, which, as a rule, is installed in the cabin or next to the control unit . Check this point when purchasing a car or at the station where the alarm was installed on the car. disable the standard alarm system on the Priora by first turning on the ignition. You will need to enter a secret code (PIN code), which must be known to each owner.

After turning off the alarm, you will also need to turn off its power. A possible malfunction may be a low battery charge level, as well as a very high current consumption by the immobilizer if it is damaged.

Starting the engine, bypassing the working unit of the standard alarm, is done by connecting power wires, bypassing the device relay. However, if you are not sure that the wires have been identified correctly, then you should contact a specialist.

Possible faults

Installing a factory alarm does not lead to the frequent need to disable the standard alarm system on the Priora. This is due to minimal functionality and the prevention of malfunctions in the event of unqualified installation of this unit on a car.

However, breakdowns can still occur, as with any electronic and electrical devices on a modern car. Among the most common types of malfunctions, in the case of using an alarm system in conjunction with an immobilizer, the following items can be distinguished:

• inability to start the engine;
• lack of response from the control unit to the key fob signal;
• failure of the body impact sensor;
• frequent alarm activation for no apparent reason;
• blocking doors after receiving a command to open.

One of the typical malfunctions of the standard device itself lies in its very design. Here, the security action underlies the blocking of the ignition system. Therefore, it is not uncommon that after 2-3 years of active use, during the next attempt to start, the starter either does not respond to turning the key, or its operation stops after a few turns.

In such a situation, the very first action will be to temporarily disable the protective device with later diagnostics. If incorrect operation of the alarm control key fob is detected, its condition must be monitored in the following sequence:

1. Monitoring the operation of buttons and the state of contacts. Inspect the key fob body for external damage.
2. Monitoring the state of the battery. If necessary, replace it.
3. Monitoring the health of the control unit. The case of the latter emerging from the influence of external sources is not excluded, although it is an infrequent occurrence. Troubleshooting in this case is the task of the service representative, who will install new software for the control unit.

Failure of the shock sensor to operate may be due to incorrect adjustment (setting). The situation looks similar when the control sensor mistakes a normal gust of wind or too much noise for a blow to the body. In this case, the car owner will not be able to install alarm connection points and control the settings on his own. You will need to contact a service station.

Another malfunction where independent intervention cannot help is the loss of the signal between the power supply and the electromagnetic wire, which is responsible for unlocking and closing the doors. It will be necessary to carry out monitoring with a special multimeter and, if necessary, replace damaged parts or reboot the device.

Central locking circuits

Locking and unlocking of the interior doors is organized through a two-step central locking chain. Three contacts of the electrical package control unit are connected to this circuit through a relay system. One power contact (12 V) and two contacts from which the control signal for the power window drives (front and rear) is removed. The two-step central locking circuit is connected through relay coils to the alarm module, and the door lock signals are removed from the alarm module.

Completion of educational program about Lada Priora

After reading, many will probably be overcome by a feeling of powerlessness. Indeed, all the described actions cannot be completed if you do not have experience in repairing Russian Zhiguli cars, as well as the skills of a specialist in electronic systems. The bulk of car owners are still ordinary people who use the vehicle simply as a household appliance and nothing more.

All thoughts are more likely to suit creative people - those who not only drive a Zhiguli, but always strive to improve. For this category of readers, all that remains is to add: all the necessary diagrams of connectors, connections, wiring are available in sufficient quantities on the network. So, you can pick up the tool and start installing the latest model of alarm system on the Priora, if one has not yet been installed to this day.