How to flush the cooling system of a Priora engine 16 valves without air conditioning

07 August 2017 Lada.Online 50 723 0

The instructions for cleaning the engine cooling system on all modern LADA cars (XRAY, Vesta, Largus, Granta, Priora, Kalina, Niva 4x4) are similar. There are no fundamental differences.

Flushing the engine cooling system yourself

During long-term operation of the vehicle, the engine cooling system may become clogged.
The presence of dirt contributes to insufficient circulation of coolant in the system. As a result, the engine begins to overheat, and the efficiency of the stove decreases. To eliminate the occurrence of these malfunctions, the engine cooling system should be flushed. The instructions for cleaning the engine cooling system on all modern LADA cars (XRAY, Vesta, Largus, Granta, Priora, Kalina, Niva 4x4) are similar. There are no fundamental differences.

Where does scale and deposits come from in the cooling system?

As you know, antifreeze does not form scale, however, if you do not completely replace it, but constantly add it, then over time its concentration will consist of more than half of water, and the additives that are included in its composition will begin to disintegrate, depositing on the walls thick layer of plaque. Read above about what happens next. Dust, oil, dirt, rubber waste and rust also contribute to contamination and can create a blockage in the cooling system or simply deposit as deposits on the walls.

How to flush the engine cooling system

We wait until the engine cools down.
Drain the fluid from the engine (unscrew the expansion tank cap and remove the drain plug on the cylinder block).
Drain the radiator (unscrew the radiator drain plug).
Pour cooling system flushing agent into the expansion tank to a level of 25-30 mm below o.
Run the engine for 10-20 minutes.
Drain the fluid from the system along with any dirt and rust.
Repeat the procedure until all dirt is removed from the system.

In other words, the process of flushing the engine cooling system is no different from regular coolant replacement.

The process is also shown in the video (using the example of Lada Priora):

To completely flush the engine cooling system

follows:

Flush the radiator (insert a garden hose into the upper radiator hose and run water through the engine radiator until all dirt is removed).
Flush the engine (insert a garden hose into the thermostat outlet and run water through the engine, watching for dirt to come out of the bottom hose).
Wash the heater radiator (disconnect two hoses from the radiator, insert a hose into one of the fittings and rinse the radiator with clean water).

What is the best way to flush the cooling system at a service station or do it yourself?

The first option is certainly simpler, but it is also more expensive, the second is less pleasant, but you will gain invaluable experience and also get good savings. If you are not short on time and have a little understanding of what SOD is, then I recommend flushing the cooling system yourself. Read on to find out how to do this.

Features and methods of flushing the cooling system

As I already said, unfortunately, the vast majority of car owners do not even know about the need to carry out such a procedure, perhaps you do the same - just add antifreeze to the level and that’s it. However, this will not always be the case, and at one unpleasant moment the cooling system will simply stop functioning, and you will get overheating with all the consequences... I recommend monitoring the condition of the antifreeze, and not adding it, but making a complete replacement, then during draining you will be able to see in what condition he is in. If you have drained the coolant and it is black or dark brown, you know that your cooling system has big problems.

What is the best way to flush the engine cooling system?

The effectiveness of cleaning the cooling system depends on what product you use to flush it:

water;
water with citric acid;
special cleaners that are sold in car dealerships;
folk remedies (Cola or Sprite).

According to reviews among VAZ car owners (survey on Lada2111.rf), most often they use fresh water (35%), special products/additives (21%) and Cola/Sprite (7%) to flush the engine cooling system.

Let us remind you that to prevent contamination of the engine cooling system, choose high-quality coolant and change it in a timely manner. The maintenance regulations for LADA vehicles (except Niva 4x4) indicate that the coolant should be replaced every 90 thousand km. mileage (or 3 years of operation). How do you rinse SOD?

Source

Coolant (antifreeze), designed to lower the temperature of an engine that heats up during operation, needs to be replaced, like any other operating fluid. In a Lada Priora car, it indicates the need to replace antifreeze every 75,000 kilometers or once every five years (whichever happens first).

You should replace the coolant in a timely manner - otherwise you risk the fact that the additives added to the antifreeze may wear out and fall out as deposits that settle on the metal elements of the engine and the cooling path. They are aggressive towards the parts described above, accelerating their wear. In addition, in this case, there is a possibility of encountering overheating of the coolant, which entails a loss of power, increased fuel consumption and a reduction in engine life by 2-3 times. This occurs due to the formation of corrosion on the internal surfaces of the engine, narrowing of the radiator channels (and, therefore, a decrease in the coolant circulation rate). And continuous operation of the engine in overheating mode leads to deformation of the cylinder oil scraper rings, which entails mixing of exhaust gases and oil.

In addition, cavitation erosion (bubbles in the coolant) and the formation of silicate sediment are possible. In winter, a worn-out cooling system can contribute to the formation of cracks in the expansion tank.

As you can see, untimely replacement of antifreeze leads to serious wear of both the entire cooling system and engine elements. Therefore, you should periodically monitor the coolant level and check it. If you unscrew the reservoir cap and see that the antifreeze has faded, lost color or become cloudy brownish, you should replace it as soon as possible.

A more or less decent auto repair shop will charge you at least 800 rubles for replacing antifreeze. (prices from an official dealer are even higher). Not all services clean the cooling system; on average, the cost of this procedure ranges from 1,300 to 2,500 rubles. You can save a lot of money by replacing and cleaning it yourself. This will not require extra effort, and you will gain good experience.

Also, do not forget to purchase a new antifreeze canister (about 1,200 rubles for a 5-liter canister) and an expansion tank cap (its price is around 100 rubles).

Replacing antifreeze on Lada Priora and cleaning the cooling system

In addition, cavitation erosion (bubbles in the coolant) and the formation of silicate sediment are possible. In winter, a worn-out cooling system can contribute to the formation of cracks in the expansion tank.

Also, do not forget to purchase a new antifreeze canister (about 1,200 rubles for a 5-liter canister) and an expansion tank cap (its price is around 100 rubles).

The following equipment and materials will be required:

Actually, antifreeze (8 liters)
Screwdriver (preferably Phillips)
Wide funnel attached to hose
Distilled water (15 liters)
Bottle brush
Key diameter 13 mm.
Citric acid or similar cleanser (2 sachets)
Expansion tank cap
Bucket or other container (volume of at least 8 liters), preferably 2 pcs.

We collect everything you need nearby so that it is at hand:

Next, you need to put the car in the pit, then open the hood. The antifreeze will cool down for some time, so you should wait a little:

After this, it is necessary to remove the engine crankcase protection. Without performing this procedure, it is possible to remove spent coolant from the radiator cavity, but not from the BC.

First, place a container for old antifreeze under the drain hole.

Important: there is no need to unscrew the cap of the expansion tank, otherwise antifreeze will violently begin to pour out around the sides.

Unscrew the bolt plug of the drain hole on the BC, drain the waste liquid into a container:

If, after unscrewing the drain cap, antifreeze does not flow out, then a plug of dirt has formed near the drain hole, which can simply be loosened with a screwdriver.

Then you need to unscrew the cap of the expansion tank (this is necessary to equalize the pressure). Then you will need to drain the antifreeze from the radiator. To avoid accidentally hitting the generator, you can wrap it in a plastic bag or wrap it in a rag.

We find the valve, which is located at the bottom of the radiator, on the right, in front of the radiator. We place an empty container under this valve.

The valve should be unscrewed carefully, as the pressure of the coolant can be strong:

The more antifreeze is poured out, the more the valve should be unscrewed. Attention: there is a rubber seal on the valve, it is important not to lose it.

As soon as antifreeze stops flowing from both drain holes, you will need to screw the drain plug on the cylinder block and tighten the radiator valve.

It is necessary to pay attention to the color of the waste liquid. If it is not very cloudy, the cooling system can be cleaned using only distilled water. If there are various floating substances, etc., in the coolant, you will need to add citric acid (1 sachet) to distilled water.

Before you begin cleaning the cooling system, you will need to remove any air pockets in the circuit.

To do this, you will need to remove the hose from the heating fitting of the throttle assembly:

Only after this can you pour water diluted with acid into the removed pipe using a pre-prepared hose with a funnel. As soon as water begins to flow from the removed pipe, stop adding coolant. Do not close the expansion tank cap yet.

Then you will need to insert the hose into the fitting and start the engine (with the neck of the expansion tank open - this is required to better clean the circuit from air pockets). Wait 5-10 minutes, then turn off the engine. After this, you will need to drain the water using the method described above.

If the used cleaning fluid does not contain suspended matter or other substances, you can begin cleaning the expansion tank. If any sediment or impurities are clearly visible in the liquid, repeat the cleaning procedure with distilled water and acid again.

Don't forget to put the drain plug back in place:

Thanks for subscribing!

Using the vehicle’s operating and maintenance instructions, remove the coolant reservoir and inspect it for damage:

If no cracks are found, the tank should be washed and thoroughly cleaned with a brush.

If the tank is cracked, it must be replaced with a new one:

In accordance with the instructions, we install a new tank instead of the old one, and then fill the antifreeze to about halfway (between the MIN and MAX marks):

After this, you will need to screw on the new expansion tank cap, then start the engine and let it run for 5-10 minutes. If during this time no smudges or leaks are clearly detected under the hood, most likely all of the above operations were performed correctly.

However, to be more sure, you can do the following.

You will need to wrap paper napkins around the connections described above (pipes, etc.):

Then you need to drive the car for some time, and the next day you will need to check the condition of the napkins. If no leaks or smudges are detected overnight, it means that everything was done correctly and the procedure for replacing antifreeze and cleaning the cooling system in a Lada Priora car can be considered complete.

How to flush the Priora engine cooling system

Yesterday (June 21, 2015) we started flushing/cleaning the engine cooling systems of two cars: my Priora and my girlfriend’s Matiz.

MATIZ

First we tackled the green Matiz. Used car 2007. It is very likely that the antifreeze has never been changed. The antifreeze was foam, which motivated specific cleaning and replacement. The job was done in a garage without overpasses. There are not so many pictures, because the business is busy, there is no time to be distracted. But we followed the principle: 1) Unscrew the radiator, remove the pipes, and take out the radiator. And separately from the car, we rinsed the inside of the radiator several times to remove foam with tap water until it was in a normal state. The expansion tank is the same. 2) Having opened the stove, start the car and pour a stream of water into the tank to rinse the pipes, again, at least from foam. We washed it and turned it off. After this, you can even blow into the tank so that the remaining water comes out as much as possible. You can see how it is blown in the video.

How to rinse SOD?

Water.
Water with vinegar and acid.
Special liquid for flushing the cooling system.

Flushing the cooling system with water

Although it is possible to flush the system with water, I would strongly advise against it. As I already said, it contains a large amount of impurities and salts that form scale. If there is no other option, then at least use distilled water. Flushing the cooling system using distilled water is done as follows:

Pour water into the SOD.
Start the engine and let it run for about half an hour.
Then turn off the engine and drain the water from the system. Repeat the procedure until your flushing fluid is the same as before flushing. The disadvantages of this method include: scale formation, low efficiency (boiling water is not able to dissolve and wash scale and other deposits).

Flushing the cooling system with water, acid and vinegar

Water with vinegar and acid is a little better than just water, because thanks to acids you can remove scale and partially clean the cooling system. In order to flush the system using this method, prepare: caustic soda, lactic acid and vinegar. The acid is added carefully and a little at a time; if you overdo it, you can say goodbye to the plastic and rubber parts of the cooling system. To completely remove scale and dirt, it takes 5-10 hours, during which it is necessary to periodically warm up the engine to operating temperature. At the end, all the liquid is drained and distillate is poured in, which is used for the final flushing of the cooling system.

Washing SOD using special chemicals

Specialist. means are the most effective and expensive option. However, the effectiveness of such a procedure is worth the overpayment. Cleaning products contain special cleaning agents that actively remove scale, grease, organic matter, etc.

Flushing specials products are divided into four types: acidic, alkaline, two-component, neutral.

Acid and alkaline are considered the least popular; moreover, they are almost impossible to find undiluted. This is explained by their aggressive effect on the entire cooling system, essentially plastic and rubber products.

Two-component products are very popular and in great demand. Their 2-component solution consisting of alkali and acid copes well with the task. Each of the components is poured into the radiator in turn.

Neutral cooling system cleaning products contain aggressive substances, such as acids or alkalis, and are used exclusively for preventive purposes.

Summing up

As you can see, there are quite a few ways and means to clean the cooling system and each of them has its own characteristics. If you do not want to spend money on expensive cleaning products, follow basic rules that will prevent the formation of plaque and scale. Namely:

Fill only with high-quality antifreeze.
Monitor its condition regularly and replace it on time.
From time to time, wash the SOD using special. facilities.

That's all for me, thank you all for your attention and for visiting our

When is it necessary to flush the engine cooling system?

Contamination of the technical channels of the internal combustion engine is indicated by the constant operation of the fan on the cooling radiator and malfunctions of the heating system. The problem must be resolved as soon as possible. You can do this yourself.

A number of signs indicate the need to flush the engine cooling system:

regular overheating and problems with subsequent startup of the power unit;
slow response to the rheostat signal;
high readings of the coolant temperature sensor after starting the engine;
pump operation with constant interruptions;
change in the color of the coolant in the tank.

If such symptoms occur, it is necessary to immediately change the fluid for flushing the engine cooling system.

Additionally, we recommend reading the article by our specialist, which describes in detail the cooling system of the VAZ-2110.

We also recommend that you carefully study our expert’s article on the description of the cooling system of the VAZ-2107.

The system can be cleaned using household products or special chemical additives.

Causes of clogged engine cooling system

The working coolant has a tendency to “boil over”. Antifreeze, distilled water or antifreeze circulates in the system - these are working coolers, which are monitored by marks in the tank and periodically topped up. Overheating and boiling over leads to loss of coolant properties and the formation of deposits in pipelines and on the internal walls of the radiator.

You can learn how to replace the coolant from our specialist’s detailed material.

We recommend that you additionally read our expert’s article, in which he talks about how to remove air from the engine cooling system.

General rules

A gentle flush of the engine cooling system can be done with distilled water. To remove scale from the walls of pipelines, special solutions will be required.

The car is placed on the site. The process begins by draining the old coolant. Special drain plugs are unscrewed at the bottom of the radiator and on the cylinder block. Used antifreeze or antifreeze is poured into a previously placed container.

The system is washed with distilled water or a weak special solution. To prepare you will need one of the components:

soda;
vinegar;
citric or lactic acid.

Sometimes Coca-Cola is used, but you should be careful about this process. “Cola” has an aggressive effect on the internal walls of the radiator.

You will need to start the engine and run the fluid for about 10 minutes. Upon completion of the process, you need to rinse the OS with distilled water, and then add new antifreeze or antifreeze.

Flushing with home remedies

Preventative work to remove scale and dirt is carried out every 6-12 months. In Soviet times, technical channels were regularly cleaned with “acidified” water. Baking soda, citric acid and vinegar were used. The solution was made in small concentrations so that the inner walls would not oxidize in an aggressive environment. The work was carried out carefully, taking into account the contamination of the canals. Such methods remain relevant today, and the process demonstrates the desired effect.

If you do not flush the cooling system, you may encounter unpleasant problems:

breakdown of the distillate heater;
unstable operation of the heating stove;
water pump blockage.

To avoid disastrous consequences, you need to figure out how to flush the car’s cooling system. Modern cleaning methods at large service stations are based on the use of special expensive compounds. Their range of use is designed to remove all possible contaminants and allows you to get rid of organic deposits and rust.

Additives are produced on the basis of two-component compositions. There are neutral options consisting of an acidic or alkaline solution. Additives provide a targeted action to eliminate a specific type of contamination.

Rinsing with distilled water

After draining the old coolant, the system is filled with distilled water.

close the valves on the radiator and cylinder block;
start the car;
keep the engine idling for up to 20 minutes;
wait for cooling and repeat the procedure.

Washing is considered complete when the distillate at the outlet is cleared of foreign inclusions. This method allows you to wash out accumulated dirt, but will not clear the channels and internal surfaces of deposits.

How to flush the engine cooling system with citric acid

It is necessary to prepare a concentrated solution. The calculation is made in the optimal proportion - 200 grams of citric acid per 10 liters of boiled water. The composition is poured into the expansion tank until the system is completely filled, but not above the maximum level.

The coolant temperature is monitored by a sensor. The scale decomposition reaction is effective at a temperature of 80 degrees. After the engine has cooled, repeat the process with a lower concentration of solution (100 g per 10 liters of water). The next flushing is carried out with clean water, and then antifreeze or antifreeze is added.

Washing with acetic acid

The procedure is also effective with 9% table vinegar. A 0.5 liter bottle is dissolved in a bucket of boiled water. The procedure consists of the following steps:

warm up the engine for about 30 minutes;
leave the charged system for at least 8 hours or overnight;
drain the used liquid and rinse with distillate.

Whey wash

The option with lactic acid or whey is an effective way to clean OS. The car will need to run in active mode (at medium engine speeds) for about half an hour or drive 40-50 km without stopping.

The serum is poured into the radiator in its pure form, without dilution with water. After washing, add water and drive again for 5-10 km. This is necessary to remove baked milk products in the technological channels. After making sure that the OS has been cleaned, fill in with clean distillate.

Washing with soda solution

Cleaning with soda is a thorough and special procedure. A careless approach can lead to excessive oxidation of metal and rubber parts. The procedure is used once a year or after traveling 50-60 thousand km. Particular attention is paid to the ratio of the components of the combined solution:

3% caustic soda;
7-10% soda ash;
85-90% boiled or distilled water.

After filling the system, you will need to drive the car up to 100 km, but you should not leave the soda solution in the radiator for more than 1 day.

If you use a sodium bicarbonate solution, you will need to thoroughly flush the system several times. After making sure that dirt and salt deposits have been completely cleaned, fill in a new distillate.

Antifreeze gradually accumulates deposits that impair the performance of the engine cooling system.

The cooling system of the VAZ-2110 works in hellish conditions . You can’t envy her, because in addition to antifreezes of dubious quality that litter the shelves (such as “antifreeze” in a beautiful blue color), the cooling system is badly affected by banal dust and dirt. There is plenty of this stuff on our roads. It is external contamination of the radiator, cylinder block, and heater radiator that often causes overheating.

And where there is overheating, there is the release of sediment and clots by antifreeze.

Danger

Cloudy liquid in the expansion tank indicates significant contamination of the engine cooling system.

All this settles not only on the wall of the water jacket, but also in the honeycombs of both radiators - the stove and the cooling radiator. After several years of such operation, the engine may overheat even in cold weather under light load. The thermal conductivity of radiators and cylinder block walls is rapidly falling, and the temperature gauge needle is stubbornly creeping up.

Consequences

To avoid consequences, at least occasionally inspect the condition of the cooling system visually. You can start by inspecting the coolant reservoir.

And this leads to very unpleasant consequences:

overheating of the cylinder head causes it to warp, this cannot be cured and the head has to be replaced;
the head gasket burns out with antifreeze getting into the oil and oil into the antifreeze;
overheating of the piston-liner pair often leads to engine seizure;
If antifreeze breaks through into the combustion chamber, it is quite possible to get a water hammer, and this is completely equivalent to replacing the engine.

This is why it is so important to keep your cooling system clean and in good working order.

Why flush the cooling system?

Antifreeze gradually accumulates deposits that impair the performance of the engine cooling system.

And where there is overheating, there is the release of sediment and clots by antifreeze.

Danger

Cloudy liquid in the expansion tank indicates significant contamination of the engine cooling system.

Consequences

To avoid consequences, at least occasionally inspect the condition of the cooling system visually. You can start by inspecting the coolant reservoir.

How and with what to flush the cooling system on a VAZ-2110

Many people start flushing the system by draining the old antifreeze. In vain, because first of all it is necessary to keep the radiator and engine clean.

Mechanical cleaning of the radiator.

If the radiator honeycombs are clogged from the outside with dirt, leaves, flies and winter road fill, there can be no talk of any cooling. The same applies to the cylinder block and engine head. Some engines are difficult to see from under a layer of dirt and oil mixture that covers the entire engine. Naturally, the heat transfer of such engines suffers greatly.

That is why, first of all, it is worth thoroughly flushing the engine and radiator outside. It is advisable to use any detergents and water under reasonable pressure for this. It is better not to get too excited with pressure, since strong pressure can damage the radiator honeycombs. There are special means for externally flushing the radiator, but practice shows that they differ from dishwashing detergents only by being overpriced.

Will folk remedies help?

Folk remedies for flushing can be quite effective, but use them at your own peril and risk.

But to flush the system from the inside, folk remedies are not enough. No Coca-Cola or other nasty stuff is good for this.

All this can only make the situation worse. It is also unacceptable to flush the system with well water or tap water - this water is too hard, which implies a huge amount of salts and minerals. They will definitely settle on the walls of the water jacket and radiator honeycombs from the inside and will completely ruin the cooling system, although after draining plain water it may look perfectly clean, causing the illusion of a sterile system.

Chemistry comes to the rescue!

The inside of the system is washed only with special products, which are abundant in stores and are inexpensive compared to a new radiator. All these means are aimed at decomposing and removing organic fats and mineral scale, which is what clogs the system the most. In general terms, all flushes are divided into several types:

Alkaline washings are inexpensive but ineffective means, although with a low degree of contamination they can bring a positive result.
Two-component washes . When using them, you must strictly adhere to the instructions; they are poured in a certain sequence; after each cycle, the system is washed with distilled water. The result is very good.

The two-component set consists of an acid and an alkaline wash.

“Soft” flushing is suitable if the antifreeze is changed regularly and there are no signs of contamination of the cooling system.

It is important to remember that different types of washes should never be mixed.

This can lead to the formation of new clots, and in the best case, the effect of the drugs will be mutually compensated and the result will be zero. The key rule when using rinsing is to strictly follow the instructions for the liquid and use it in combination only with good quality distilled water.

There are two types of SOD purification:

External - when insects, dust, oily stains, dirt and other nasty things are removed from the surface of the radiator. Typically, this cleaning is done using a jet and car shampoo.

Dirty radiator - poor cooling

Internal - provides for the removal of deposits consisting of rust, scale, antifreeze decomposition products and rubber parts from the engine cooling jacket and radiator. In addition, contamination and scale are possible in cases where the car owner uses ordinary tap water as coolant. This should not be done under any circumstances, since such water contains a huge amount of salts, impurities and various substances, which, when heated, are deposited on the walls of the cooling system in the form of plaque, complicating heat transfer and reducing the cross-section of the SOD passages.

We flush the cooling system with our own hands

It is advisable to carry out washing at least once a year. This is guaranteed to save us from problems with engine overheating.

We change old antifreeze of unknown color without hesitation.

Naturally, it is advisable to replace the antifreeze during the washing process. However, if the antifreeze is fresh and clean, this is not necessary. In this case, when draining the liquid, place clean containers under the radiator tap and the cylinder block plug.

After draining the antifreeze, tighten the drain valves and plugs in accordance with the flushing manufacturer’s recommendations, fill the system with the mixture and warm up the engine to operating temperature or wait until the radiator fan turns on.
We drain the flush and assess its condition.

If after the first time a cloudy liquid comes out of the system, repeat the process with a new portion of flushing.

We finish this “water procedure” when clear water flows.

Fill with antifreeze and tighten the reservoir cap.

When the engine has cooled down, check the antifreeze level in the expansion tank.