Lifan Solano 620 does not start reasons the starter does not turn

A car engine starter is an electromechanical device, the purpose of which is to transmit torque from the armature of the electric motor to the flywheel of the power unit, which brings the engine to a running state.

Due to the increased load and frequency of operation, this part has a short service life, which quite soon leads to the need to replace the starter with a new one.

The approach of a part to the final stage of operation is characterized by the appearance of minor faults, which, if neglected, will negatively affect the functioning of the engine and can cause a car breakdown on the highway. The most common causes of starter failure are the following:

• The electric motor rotates, but the engine does not start - first you need to check the condition of the terminals and the battery charge level. Also, the cause of the malfunction may be low adhesion of the Bendix gear to the flywheel, which indicates grinding of the gear teeth or the flywheel itself. To correct the situation, the parts will have to be replaced with new ones;
• The efficiency of the starter decreases as the motor resistance increases - the cause may be wear on the armature brushes or problems in the operation of the pull-out relay. Also, as in the first case, it would be a good idea to check the condition of the wiring for melting or oxidation of the main cables or terminals;
• The electric motor rotates the crankshaft too slowly - there may be a low level of electrolyte inside the battery case or a mismatch in the viscosity level of the oil inside the engine. If the problem occurs in winter, you just need to warm up the engine with a hairdryer so that the technical fluid “defrosts”;
• During start-up, the engine experiences a creaking sound - extraneous sounds that occur when the engine is ignited are the cause of incomplete charging of the battery (voltage less than 12.6V) or the result of damage to the armature brushes or head teeth;
• The start and relay do not show signs of life when trying to start the engine - there may be a short circuit in the engine electrical system, a break in the insulating winding of the housing, or failure of the electromagnetic relay;
• The relay makes noise, but the engine does not start - there is a problem in the power unit of the unit or a break in the electrical circuit; wear on the armature brushes is also possible.

Note! Before disassembling and dismantling the car's electric motor, it is recommended to check the condition of the terminals on the starter and battery - cases of problematic engine starting due to oxidized terminals or a low battery charge level are not so rare.

Lifan Solano won't start, what's the reason?

Let's start with malfunctions when the starter does not turn. Everything here is simpler than steamed turnips.

If you don’t hear the activation of the solenoid relay, check whether + is supplied to the black-yellow wire when you turn on the ignition key. It is better to check at the contact point on the starter solenoid relay. Getting to it is not easy, but it is possible. The starter for the Lifan Solano is located on the far side of the engine, under the intake manifold.

Check all fuses; see the owner's manual for the fuses. First of all, look at the two 30-amp fuses in the interior mounting block. In Solano, to see the mounting block, you need to lie with your head on the driver's mat and look up.

These fuses provide ignition. When they burn out, not only the starter does not work, so if everything works, then the reason is clearly not in them.

If there is no positive on the wire of the retractor relay, and the fuses are intact, then the reason is either in the wire and unreliable contacts, or in the ignition switch. In this case, you need to check for the presence of a plus on this wire directly at the ignition switch.

If the solenoid relay is activated but the starter does not turn. The brushes could simply be worn down; this can be solved by removing the starter and replacing the brush assembly. You should check for positive voltage on the red wire going to the starter from the battery. This wire goes directly from the battery to the starter, but through the contacts on the mounting block under the hood!

These very contacts sometimes burn out, remove the cover from the mounting block and check for traces of melted wires.

Another reason for a non-functioning starter is lack of ground on the engine. The negative wire is screwed to the front of the gearbox; be sure to check the reliability of its fastening and the quality of the contact. It is better to unscrew rusted contacts, clean them and tighten them again.

The starter turns but the engine does not start

This also happens, here the troubleshooting goes in a slightly different direction. First of all, of course, sparking and fuel supply are checked. Vlifan Solano the operation of the fuel pump can be blocked by the standard security system. Listen carefully, can you hear the fuel pump running when you turn on the ignition?

If not, then try arming and disarming the car again using the standard key. If that doesn’t help, then as a last resort you can disable the fuel pump lock. To do this, remove the heater control unit. To do this on the Lifan Solano you need to remove the wood-look trim and unscrew the two bolts. Everything else is attached with latches.

Below it is the BCM (Body Control Module). For convenience, it is better to remove it; it is secured with two “8” key bolts. There are three connectors connected to the block - one long at the top and two small at the bottom. We need a white connector at the bottom.

We find a violet-green wire in this connector, this is an enabling plus for the operation of the fuel pump relay. Feel free to cut this wire close to the connector. The cut wire that goes into the harness must be stripped and connected to the blue-green wire in the same connector. The blue-green wire is the wire on which positive voltage appears when the ignition is turned on.

That's it, now the fuel pump will work regardless of the quirks and glitches of the security system. Of course, the function of blocking it will be lost if you try to start the car with the alarm not turned off.

Checking for spark and injector operation

If there is no spark, the engine will also not start. You can check the claim very simply, but you need an assistant. Remove the rubber tip of the high-voltage wire from the spark plug and pull it out slightly. That is, you need to raise the tip above the spark plug by 5-7 mm, no more, otherwise, if the spark has nowhere to go, the ignition module or control transistors in the ECU may burn out.

Lift the tip and ask an assistant to turn the starter with the ignition key. If there is a spark, you will hear clear clicks in the spark plug well. Check all four cylinders in this way. If there is no spark, then the reason may be either in the high-voltage wires or in the ignition module.

At the injectors you can only check the constantly incoming plus 12V. on the blue-red wire. When the ignition is on, there should be +12V on-board voltage on this wire for each injector. If it is not there, then look at the fuses again.

Constant plus is supplied to the injectors when the ignition is turned on, through fuse FS04 and the main relay. The fuse and relay are located in the mounting block under the hood. Their names are signed on the bottom of the lid, in English - main.

Broken timing belt

If the timing belt breaks, the car will not start either. But you will immediately feel that the starter is turning “something wrong.” The flywheel rotates without load, so the starter turns very easily.

Here are some reasons why the engine cannot start, search and you will find,

Read interesting articles on the topic below:

Source: https://www.em-grand.ru/post-ne_zavoditsya_lifan.html

Dismantling

The starter on a Chinese car is located inconveniently - between the engine and the engine shield, under the intake manifold. You have to dismantle the interfering components and use a device consisting of several tools.

Step-by-step algorithm of actions:

• remove the battery along with the platform under it;
• disassemble the air filter corrugation;
• disconnect the wires going to the starter;
• pull out the gearbox cable mounting bracket;
• remove both mounting bolts.

The positive wire coming from the battery is secured with a nut. Unscrewing this fastening is extremely inconvenient, since you have to use the wrench under the intake manifold. A homemade device will help here - an extension cord, a ratchet and a head of the required size assembled together. The second wire from the ignition switch simply has a removable plug at the end - just pull it out.

Starter Lifan Solano: where is it located, how to remove, replacement

A car engine starter is an electromechanical device, the purpose of which is to transmit torque from the armature of the electric motor to the flywheel of the power unit, which brings the engine to a running state.

Due to the increased load and frequency of operation, this part has a short service life, which quite soon leads to the need to replace the starter with a new one.

The approach of a part to the final stage of operation is characterized by the appearance of minor faults, which, if neglected, will negatively affect the functioning of the engine and can cause a car breakdown on the highway. The most common causes of starter failure are the following:

• The electric motor rotates, but the engine does not start - first you need to check the condition of the terminals and the battery charge level. Also, the cause of the malfunction may be low adhesion of the Bendix gear to the flywheel, which indicates grinding of the gear teeth or the flywheel itself. To correct the situation, the parts will have to be replaced with new ones,
• The efficiency of the starter decreases as the motor resistance increases - the cause may be wear on the armature brushes or problems in the operation of the pull-out relay. Just as in the first case, it would be a good idea to check the condition of the wiring for melting or oxidation of the main cables or terminals,
• The electric motor rotates the crankshaft too slowly - there may be a low level of electrolyte inside the battery case or a mismatch in the viscosity level of the oil inside the engine. If the problem occurs in winter, you just need to warm up the engine with a hairdryer so that the technical fluid “defrosts”
• During start-up, the engine is observed creaking - extraneous sounds that occur when the engine is ignited are the cause of incomplete charging of the battery (voltage less than 12.6V) or the result of damage to the armature brushes or head teeth,
• The start and relay do not show signs of life when trying to start the engine - there may be a short circuit in the engine electrical system, a break in the insulating winding of the housing or failure of the electromagnetic relay,
• The relay makes noise, but the engine does not start - there is a problem in the power unit of the unit or a break in the electrical circuit; wear on the armature brushes is also possible.

Note! Before disassembling and dismantling the car's electric motor, it is recommended to check the condition of the terminals on the starter and battery - cases of problematic engine starting due to oxidized terminals or a low battery charge level are not so rare.

Popular starter models

The principle of operation of the electric motor on the Lifan Solano is as follows: the exhaust relay, when receiving a current charge, forces the Bendix gears to come into contact with the flywheel teeth and turn the part, which leads to the direct start of the engine.

The ignition process occurs when the electric motor armature begins to rotate due to the receipt of a charge of electricity, which in turn transmits torque to the bendix.

THIS IS INTERESTING: Question: Can fog lights be used during the day?

Country of origin Product code Product power, kW/h Approximate cost, rub.

Despite the budget price of the brand, there is a huge amount of counterfeit products on the automotive components market, which not only have a short service life, but can also cause short-term wear in the car.

To prevent the possibility of purchasing a low-quality part, it is necessary to check the compatibility of the spare part before purchasing - to do this, compare the part number with the VIN number of the vehicle on the official website of the manufacturer. If the database does not contain information about a given manufacturer, it is recommended not to purchase a starter.

How to dismantle an electric motor for repair: step-by-step instructions for beginners

The electric starter on the Lifan Solano is located under the engine on the driver’s side, which makes some adjustments to the procedure for dismantling the part - for successful removal it is necessary:

• Disconnect all terminals from the battery to avoid short circuits,
• Remove the plastic engine cover, if included,
• Disconnect all terminals from the starter,
• Unscrew a pair of fixing bolts located at the bottom and top of the electric motor housing - the Solano starter is attached to the engine compartment.

During dismantling and further repair of the starter, it is not allowed to drop or hit the part - even slight mechanical pressure can damage the electric mechanisms of the starter, which will make the part completely unusable. Also, during subsequent installation of the electric motor, it is necessary to observe the polarity of the axes during installation and ensure correct engagement of the teeth of the flywheel and the Bendix gear - otherwise the system will not work efficiently.

At the end of the procedures, the part can be carefully removed and disassembled for repair.

It is important to remember that you should not completely disassemble the starter - usually repairs are carried out by disassembling the housing and disconnecting solid blocks of electrical components; disassembling the stator or rotor without the appropriate equipment is not recommended.

Remember, homemade repair of the starter can lead to a short circuit in the vehicle's electrical systems and significantly reduce the service life of the power unit.

Source: https://uazlyuks.ru/komplektuyushhie/starter/starter-lifan-solano

Original devices and analogues

Lifan Solano is equipped with 3 options of standard starters:

• LF481Q1-3708100A at 1.4 kW;
• LF481Q3708100A at 1.4 kW;
• LF479Q33708130A at 1.6 kW.

The price of devices varies between 3.5-4 thousand rubles.
Analogues also made in China are also suitable:

• LF479Q33701180A;
• LF479Q3-3701180A;
• 81Q3-3701111;
• 81Q3-3704311.

All of them produce power up to 1.4 kW.

Despite the budget nature of the Lifan Solano, there are many fake spare parts on the market, including the starter. Such a device not only serves little purpose, but also causes a short circuit and even a fire in the car.

How to replace the valve cover gasket on Lifan Solano

Petrol engine R4 16V 1.6 l - instruction manual. The engine does not start after replacing the timing belt or chain. Replacing the drive elements of the gas distribution mechanism is a planned procedure that is performed at certain intervals or as necessary.

In the first case, we are talking about replacing the timing belt or chain, as well as rollers, chain tensioner and other drive parts after a strictly defined number of kilometers traveled, on average for a belt the figure is 50-60 thousand. Also, the reason for an unscheduled replacement of a belt or chain can be an accelerated wear, the appearance of extraneous sounds during operation, etc. In some cases, a situation arises when, after replacing the timing belt or chain, the car engine does not start.

This problem can occur on a car regardless of the make and model of the vehicle, the design features of the power unit, etc. In this article we intend to talk about why the engine does not start after replacing the timing belt, as well as for what reasons after How to replace the valve cover gasket on a Lifan Solano timing belt has difficulty starting the power unit, the internal combustion engine is unstable, or other problems arise with the engine.

After replacing the timing chain or belt, the engine does not start: the main causes and troubleshooting. Before starting diagnostics of the timing drive, it is recommended to immediately check the proper operation of the ignition system, the condition of the battery, the correct connection of the power system elements, electronic ECM sensors, etc.

If no malfunctions are identified, then we move on to the gas distribution mechanism drive.

In the list of the main reasons why the car does not start after replacing the timing belt or problems appeared after the chain drive was changed, experts identify possible damage to the valve mechanism and misaligned valve timing as a result of improper installation.

Similar malfunctions can occur on different car models. First of all, it is important to know that errors when replacing the timing drive can lead not only to failures, but also to subsequent breakdowns. It is also necessary to separately take into account the reason why the drive elements had to be changed. The engine does not start: the valves are bent.

For example, if the timing belt breaks, then the belt is changed and the car does not start, then bending of the valves after such a break should not be ruled out. The fact is that at the moment the belt breaks, the valve timing on many engines is disrupted, the camshaft does not rotate, and the timing belt stops working. This means that the valves no longer open and close in a timely manner. However, the pistons in the cylinders still continue to move.

It often happens that the valves remain open, causing the pistons to hit. In this case, the valves become bent, and the pistons can also be damaged.

At the same time, replacing the timing belt alone cannot solve this problem, since the engine requires separate expensive repairs. Note that previously, internal combustion engine manufacturers took into account the risk of bending and machined special recesses for the valves on the piston surface.

At the same time, the presence of such grooves reduces engine power, as a result of which such a solution was abandoned on modern engines. The valves can be checked in the field by removing the valve covers, after which the engine is cranked by hand and the operation of the mechanism is assessed.

If it is noticed that any valve is not working, then it is bent. Please note that such a check is just a superficial diagnosis, since even with bent valves the mechanism will often visually work normally.

For this reason, to accurately assess the condition of the valves, it is preferable to remove the cylinder head. Once removed, bent valves can be quickly identified and the procedure for replacing them can begin immediately. Please note that it is recommended to replace all valves immediately with new ones, and not replace only bent ones.

Engine repair on Lifan Solano

Also, during the installation process, it is necessary to grind in the valves. The timing belt was replaced incorrectly.

Unqualified replacement of the timing drive often leads to the fact that after replacing the timing chain, the engine starts poorly, a belt-driven motor does not start, etc. The problem is that the timing belt may not be aligned and the phases do not match.

The result is that the operation of the gas distribution mechanism and the ignition system is not synchronized, the mixture is compressed in one cylinder, and a spark is formed in the other.

Watch video Replacing Lifan Solano spark plug well seals online, download to your mobile phone

For these reasons, an important point is the exact match of the marks on the pulleys. During the replacement process, special attention should be paid to the position of the marks. The engine is set to the end of the compression stroke in the first cylinder, after which the position of the marks is checked.

If a deviation is noticed, then this is the reason the engine refuses to start. In such a situation, the timing belt must be removed and the camshaft pulley must be correctly aligned taking into account the marks.

Let us add that many car models also have a special mark on the flywheel, which must also match. It should be noted that the flywheel is usually dirty. In many cases, this makes the tag difficult to detect.

As practice shows, on the flywheel, in addition to the mark that needs to be set, there may also be characteristic indentations-pits.

If you mistakenly replace the mark with the edge of the hole, which is visually similar to the mark, then the engine will not start. Also, during the process of replacing the timing drive on cars with a carburetor, the ignition may go wrong. Quite often, a violation of the spark supply to the cylinders can be determined by installing the spark plug armor wire of the first cylinder to the fourth, and the wires from the fourth cylinder to the first.

THIS IS INTERESTING: Why the stove in the car does not heat well

In some cases, after such a rearrangement, the engine can be started. If such a failure is detected, then the gas distribution mechanism drive must be set correctly, and if necessary, additional adjustments and adjustments to the ignition system are also made. Tips and tricks.

Why does oil press through the cuffs of spark plug wells on Lifan Solano

On vehicles with a timing belt, it is strongly recommended not to limit yourself to replacing just one belt. At the same time, new rollers should be installed.

Ignoring this rule may lead to subsequent jamming of the rollers and breakage of the new timing belt. Also, after installation on old rollers, the new belt may slip and accelerate wear.

Even if the engine starts normally, you may encounter noticeably increased noise during engine operation. Let us also add that, structurally, the timing belt can also drive the water pump of the cooling system.

During replacement, you should separately check the condition of this element, and also change the pump strictly according to the regulations.

If the water pump jams, then the belt may also break. This suggests that during the work the contact chip for some sensor could have been damaged. To accurately determine the cause, the engine can be scanned for errors using a special OBD2 scanner. When selecting belts and rollers, it is necessary to install high-quality analogues or original parts.

VIDEO: Valve cover gasket is leaking

You can purchase spare parts either as a ready-made installation kit or separately. Remember, there may be low-grade counterfeits of ready-made timing belt installation kits on sale from well-known companies Gates, Inna, etc. Finally, we note that replacing the timing mechanism drive is rightly considered a responsible procedure.

Incorrect installation can lead to engine failure or unstable operation of the power unit. If you are not confident in your abilities, then it is better to entrust this procedure to experienced car service specialists. Tips and tricks On cars with a timing belt, it is strongly recommended not to limit yourself to just replacing one belt.

Source: https://dshop-centr.ru/lifan/kak-zamenit-prokladku-klapannoy-krishki-na-lifan-solano.php

Cold start

The starter starts when the battery has sufficient charge, so sometimes this can cause problems starting the engine. The situation gets worse if the oil crystallizes in the cold. These factors together lead to the battery completely losing its charge the next time you try to start the engine, so you can’t do it without outside help.

In this case, experienced car enthusiasts recommend using a proven method - recharging the battery from a charged and normally functioning one.

This is done using special wires, which in everyday life are called “crocodiles”. First, connect the wires for lighting to the donor's car. The positive wire is connected to the positive terminal of the battery, then the negative wire is connected to the negative terminal. The headlights of the donor car are turned on in order to increase the load on the generator and equalize the voltage with the “lighted car”. Next, the positive wire with the other end is connected to the positive terminal of the “lighted car,” that is, Lifan Solano, and the negative wire is connected to the “body” of the car.” This connection procedure will avoid any risk to the batteries. Make sure that the wires do not touch each other when connecting, otherwise a short circuit will occur.

Where are the fuses on lifan solano?

The interior of the Solano creates an equally pleasant impression. The balance between the number of buttons, chrome, wood decor and plastic is perfectly maintained here. The quality of materials and workmanship is not inferior to European cars.

The seats are upholstered in faux leather, and the interior is given additional presentation by details traditional for Asian cars: aluminum-painted door handles and an insert on the central part of the dashboard, as well as wood-effect inserts surrounding the interior.

All controls are exactly where they should be, and there is ample legroom and headroom to keep all passengers comfortable, even on long journeys. I'm on Odnoklassniki - Let's see how you have to dodge to change the fuse!!!

LIFAN Solano does not start - standard lock

The use of a fuse with a higher rating or improvised means in place of a fuse is strictly prohibited. Otherwise, it may cause serious damage to the vehicle. We remove the standard lock on the Lifan Solano. We check the fuel pump relay. We disassemble the front panel.

Review part 2. Fuse and relay box. In the instrument panel

If the headlights or other electrical equipment does not work, you need to check the fuse. If the fuse is blown, replace it with a new fuse of identical rating. Review of the fuse and relay box in the Chevrolet Aveo T-300 instrument panel, in the first part, see the review of the fuse

all about LIFAN 01 Nov 2022 0 Comments

Modern cars, like Lifan Solano, are equipped with different electronic systems, which allows them to be used in different conditions. But to prevent the system from breaking down at an inopportune moment for the owner, you should always take care of the serviceability of all components and parts. And first of all, pay attention to the serviceability of the fuses. Only this element can protect the system from burnout in case of overload, overheating or for any other reason.

all about LIFAN 01 May 2022 0 Comments

Only changing blown fuses protects electronics from failure. But the systems of different car brands are equipped with different types and types of fuses, which can be located in different places. The starter turns, but the fuel pump does not pump, and the lights are constantly on when the ignition is on.

all about LIFAN 09 Nov 2022 0 Comments

In Lifan Solano, as in cars of other brands, there are components and assemblies that most often fail. And in order to prevent serious damage, it is necessary to replace them on time. You can check their serviceability yourself, but to do this you need to know where they are located. And our connector was fried for one banal reason - the fuses in the mounting block were higher than the nominal

all about LIFAN 22 Jun 2022 0 Comments

The cost of a mounting block with original fuses for a Lifan X60 car starts from 5,500 rubles, analogues from 4,200 rubles.

all about LIFAN 24 Mar 2022 0 Comments

Source: https://komtrans-avto.ru/vse-pro-lifan/gde-nahodyatsya-predohraniteli-na-lifan-solano.html

Typical faults

The main malfunction is when the starter does not rotate.

1. In this case, start by checking the solenoid relay. It is necessary to determine whether “+” is supplied to the black-yellow wire when the ignition is activated. It is better to do this at the junction of the contact on the traction relay. However, getting here is not easy, since the starter is located on the far side of the engine, under the intake manifold. It is recommended to use a hydraulic lift.

• Next, check the fuses. First of all, inspect the two 30-amp elements located in the interior mounting block under the dashboard. They control the ignition, so if they burn out, they affect not only the operation of the starter. There is no separate relay for the starter on a Chinese car, although the instructions indicate that there should be one.

If the relay receives “+” and the fuses are fine, look for the cause of the malfunction in the wiring, contacts or ignition switch.

The next problem is that the solenoid relay is activated, but the starter does not rotate.

1. The brushes are worn out and need to be removed and replaced.
2. There is no “+” on the red wire coming from the battery. This cable runs through the mounting block located in the engine compartment. First of all, check here to see if there are any burnt contacts or melting.
3. There is no weight on the engine. This wire should be located in the front of the gearbox - here it is screwed. Check the quality of the connection and the presence of oxides.

Another typical malfunction is that the starter rotates, but does not start the engine.

1. Check the fuel system and sparking. Determine whether the standard alarm is blocking the operation of the fuel pump. Disable the pump blocker to diagnose the operation of the starter without it. To do this, it is enough to remove the heater control system, under which the BCM unit is located. The latter is held on by two M8 bolts. There are three connectors on it - the bottom one is white. This plug has a blue-green wire that is responsible for supplying “+” to the fuel pump relay. Trim it so that you can join it later. Now the pump will start working without control from the security system, which will eliminate glitches and blocking.
2. Check to see if the timing belt is broken. The sound of the starter turning should change.

Replacing silent blocks on the front arms Lifan Solano video

Car services and service stations by car brand.

How to get to a gas station with an empty tank? Reasons why the engine may not start. Replacement of shock absorbers and springs of the Lifan Solano suspension Replacement of levers and ball joints of Lifan Solano Replacement of silent blocks of the Lifan Solano suspension Replacement of struts and bushings of the Lifan Solano stabilizer Replacement of the hub, wheel bearing of Lifan Solano Replacement of the front supports, support bearing of Lifan Solano How to unscrew a rusty bolt.

https://www.youtube.com/watch?v=KkUG2i1nlHU

Why won't the car start? Drive to the gas station with an empty tank. What is the best way to treat the underbody of a car against corrosion?

Material on the topic: Why is the fuel filter suitable for Lifan Solano

Repair request. Our coordinates. Repair Lifan Solano at a car service center.

How to replace the silent blocks of the Lifan Solano suspension ()

The silent block of the Lifan Solano suspension is a small-sized hinge, equipped on both sides with metal bushings, which are placed in rubber inserts.

The purpose of this element is to dampen the noise of the Lifan Solano suspension and protect other components and mechanisms from shock and vibration that occur when driving.

Considering the increased load on the chassis of the Lifan Solano, it is not surprising that the silent blocks of the Lifan Solano have to be changed quite often, especially if the car is not actively used in the best conditions.

There are several direct and indirect signs that the silent blocks of the Lifan Solano suspension require replacement: Lifan Solano began to respond more slowly to driver actions when turning the steering wheel in different directions. A visual inspection reveals cracks and other types of damage to the rubber component of the silent block.

When attempting to exert physical influence on these elements, a backlash above the permissible level is observed.

Tires installed on Lifan Solan begin to wear unevenly. When driving even short distances, you can hear the chassis creaking. The destruction of Lifan Solano's silent blocks leads to an increase in noise in the cabin, which can lead to driver discomfort and a decrease in his concentration while driving the car.

In addition, given that the Lifan Solano begins to respond more slowly to steering control, and the tires wear out unevenly, this immediately increases the chance of getting into a traffic accident, with all the ensuing consequences from this situation. If one of the above signs is detected, you must immediately check the Lifan Solano chassis as a whole, and replace the Lifan Solano suspension silent blocks, if necessary.

Technology for replacing silent blocks of automobile suspensions Before repairing silent blocks of the Lifan Solano suspension, you need to prepare everything you need: Special press equipment designed for pressing silent blocks. An ordinary hammer, chisel and vice.

Set of socket and socket wrenches. New spare parts and liquid soap.

THIS IS INTERESTING: Quick answer: How to change the low beam lamp on a Polo?

In addition, to carry out repairs to the Lifan Solan chassis, a lift, overpass or inspection hole is not required, since the first stages will need to be performed under the bottom. The procedure for replacing the silent blocks of the Lifan Solano suspension looks like this: Lifan Solano is placed on a lift.

The casing protection is being dismantled. The fastening nuts of the front arms and the stabilizer strut of the Lifan Solano are unscrewed. Using a funnel, the bolt is knocked out, then the fastening bolts on the wheels of the car are loosened.

Using a jack, the Lifan Solano is raised and the wheels are finally removed. In order to relatively easily unscrew the nuts of the extensions, it is recommended to pre-treat the threads using a special high-pressure agent and clean it with a metal brush.

To dismantle the suspension arm, you must first disconnect the ball joint from the Lifan Solano steering knuckle. To do this, you will need to unscrew the two fixing bolts. Having gained access to the damaged silent blocks of the Lifan Solano suspension, you can begin to replace them: Lifan Solano front arm silent block To facilitate the dismantling process, you can further break the hinge, then easily remove the bushing and, using a regular screwdriver, remove all the remains.

Afterwards, the installation site is cleaned of traces of rust, and the new silent block is lubricated with liquid soap to facilitate its installation. Pressing is in progress.

Lifan Solano 2012 - DIY repair

Carefully tighten the fixing bolt. Silent block for stretching Lifan Solano The hinges are knocked down quite easily with the help of a pre-prepared chisel. Places for installation are cleaned, and the silent block is pressed into the lever.

If it was not possible to immediately install it completely in place, then the lever is located on a flat surface and the element is pressed using a regular hammer or a small sledgehammer. This should be done extremely carefully so as not to damage the newly installed silent blocks.

Source: https://autoeksp.ru/lifan/zamena-saylentblokov-na-perednih-richagah-lifan-solano-video.php

Price:

Where are Lifan Solano starters made in St. Petersburg:

WhatAapp/Viber: 8-911-766-42-33

We do not repair units removed from the vehicle. We do our own diagnostics, make a diagnosis and provide a guarantee.

– the car does not start, the starter shows no signs of life; – when trying to start the car, a noise is heard, the car does not start; – after starting the engine, the relay does not turn off;

Warranty for replacement – ​​360 days, for repair – 180 days.

If necessary, we can help with the evacuation of the car to our service stations.

Addresses in St. Petersburg: Service station on Bolshevikov: st. Voroshilova, house 7, from 10 to 18, t., Sat, Sun – closed. Service station on Grazhdansky: st. Uchitelskaya, building 23, from 9.30 to 21.00, t., seven days a week. Service station on Kupchino: st. Dimitrova, building 1, from 10 to 20.00, t., seven days a week.

Lifan Solano clutch replacement - Auto repair

The modern automobile market is developing rapidly and the Lifan Solano car, which appeared not so long ago in the CIS countries, has managed to win the trust of many drivers. This is due to the low cost, ease of operation and maintenance of the car, as well as its safety and attractive appearance.

Of course, this is not an elite vehicle and it is designed for “ordinary” people, so drivers, as a rule, carry out identification and elimination of all problems and carry out repair work themselves.

Problems with the clutch can occur both in well-used cars that have covered more than one thousand kilometers, and in almost brand new cars. To determine what exactly is broken or is not functioning correctly, you should know the “symptoms” of a faulty clutch. By the way, not always, if the car’s gears do not engage, it is the fault; read more in the material: Why the gears on the Lifan Solano do not engage.

Signs and causes of a faulty clutch

This is what a new clutch disc looks like

The main causes of failure of clutch structural elements are:

• Careless behavior of the driver when operating the vehicle - pressing the clutch while the vehicle is moving, etc.
• Of course, you may end up with an “unsuccessful” car with a obviously low-quality part, non-original components, etc.
• All things have their own service life and parts can simply wear out, this especially applies to the driven disk - with careful driving, it becomes unusable after 100 thousand kilometers, but for lovers of “high speeds” even faster.
• Due to wear or damage to the integrity of the gearbox or engine oil seals, oiling of the fractional lining of the driven disk may occur.

Signs of clutch problems most likely include:

• When incomplete shutdown is observed, they say “the car is driving,” and difficulties arise at the moment of shifting gears with the engine running, accompanied by crackling, humming, and noise. This may indicate possible damage to the driven disk lining, contamination or depressurization of the hydraulic drive, etc.
• When the clutch “slips,” that is, poor vehicle dynamics are observed, fuel consumption increases sharply, the engine overheats, etc. This “behavior” is typical when oiling, damage to the integrity or wear of the driven disk, breakdown of the working cylinder, etc.

Replacement process

It must be said right away that this is a difficult and time-consuming process, so if the need for replacement arises, you should prepare all the necessary tools in advance - for the work to be fast and productive, everything should be “at hand”.

Working "under the hood".

1. First, you need to remove the protection from the bottom of the engine compartment (engine crankcase), and, opening the drain cover with a key, drain all the oil.
   If it is subsequently used again, it must be placed in a clean container (can be in a 2.5–3 liter jar, since the total amount of oil is 2.1 liters).
2. As stated earlier, replacement is a long process and there is not a moment to waste.
   So, while the oil is drained, you can begin other manipulations - removing the battery and its platform.

   In this case, the terminals are disconnected from the battery in the order: “minus”, then “plus”.

3. Afterwards, the air filter is removed and its top cover is removed along with the pipe up to the throttle valve.
   To do this, you need to loosen the clamp on the throttle body pipe and quickly disconnect the pipe, then unscrew the 3 bolts that secure the lower part of the air filter. Note: To prevent dirt and dust from getting into the throttle assembly, it must be covered with a clean piece of cloth.
4. Now you need to disconnect the two hoses connected to the absorber and remove the absorber from the bracket (with a sharp upward movement).
5. The cables are separated from the gearbox and moved to the side, and the same is done with the working cylinder.
6. All existing crankshaft position, speed and reverse sensor connectors are disconnected.

Working "under the car"

1. First of all, the front wheels are removed and the suspension is partially disassembled (to disconnect the wires from the gearbox). Now it is possible to disconnect both the right and left hubs. The starter located under the exhaust manifold is removed or moved to the side. Note: for such manipulations you should invite an assistant.
2. Now you can disconnect the gearbox and only when it is completely removed can you observe the clutch mounted on the flywheel.
3. The clutch basket, secured with 8 bolts, is unscrewed from the flywheel (it must be thoroughly cleaned of possible contamination).
   Next, a new basket with the clutch disc is installed and loosely screwed in, the disc is carefully centered, and after that you can tighten all 8 bolts tightly.

   This is what one part of the gearbox looks like when this part of the box has already been removed

   This is what the gearbox looks like in the place where the clutch kit is installed

   This is what an old clutch with a mileage of 60,000 km looks like on Solano

4. Subsequent assembly is carried out strictly in reverse order. Note: along the way, if necessary, you can check and clean other elements and parts of the car.

Clutch adjustment

After replacing the clutch, it may need adjustment. Read more about the adjustment here.

Part numbers

W21200H - Krafttech clutch kit

Transmission

How to remove the Lifan Solano clutch forkReplace the Lifan Solano air filterReplacing the Lifan Solano speed sensorInstalling the Lifan Solano clutch discInstalling the Lifan Solano gearboxRepairing the Lifan Solano driveshaft crosspieceChange the oil in the Lifan Solano gearboxChange the Lifan Solano oil filterInstalling the Lifan Solano external grenade with your own handsRemoving the Lifan Solano clutch pedalReplacement drive Lifan speedometer SolanoReplace the boot of the Lifan Solano inner CV joint with your own handsReplace the boot on the Lifan Solano grenadeHow to replace the boot of the outer CV joint of Lifan SolanoReplace the gear shift lever of Lifan SolanoHow to replace the Lifan Solano cabin filter with your own handsReplace the rear axle oil seal Lifan SolanoReplace the Lifan Solano gearbox oil seal with your own handsRepairing the Lifan Solano gearbox oil sealReplacing the Lifan axle shaft oil seal SolanoChange the Lifan Solano drive sealRepair the Lifan Solano gearbox seal with your own handsChange the Lifan Solano fuel filter with your own handsChange the Lifan Solano clutch cableRepair the Lifan Solano automatic transmission filter with your own handsInstalling the Lifan Solano engine filterChange the Lifan Solano air conditioning filterRemove the Lifan Solano clutch cylinder

Selecting a battery by car make

Electric batteries are used on motorcycles or vehicles. The battery energy powers the starter, engine control unit and lighting equipment. The main characteristics of the products are:

• capacity;
• voltage value;
• and starting current.

All car manufacturers use different classes of batteries on their units. They differ not only in the above characteristics, but also in different operating resources. During operation, batteries may lose their characteristics, and therefore they must be changed periodically.

Features of selection

To make the right choice of car battery, you need to know the technical factors of the energy storage device.

It is important to take into account every detail, including the possibility of cold scrolling, which is important for residents of the Russian Federation in winter. All these parameters are set by the car manufacturer

Only a professional can know how to correctly select the battery according to its parameters.

Our advantages

Our battery store presents its services to you, where you can find energy storage devices for every taste. All products that we present have an official guarantee from the manufacturer and are original. The assortment includes products from the best domestic and foreign brands.

On the website you can select a battery for your car online. A convenient search system will give you the opportunity to find out the full characteristics of the offered product. You can also buy a battery from us, matching your car in different price ranges. If necessary, you can always ask the operator for advice.

When choosing batteries for a car, the selection by car brand is made taking into account how much the car’s electrical system consumes. The battery series depends on this. Manufacturers usually offer at least three battery options for a specific car model. They differ in characteristics and resource.

Some models can last 2 years, while others can last 5 years or more. To make the correct choice of battery for a car on our website, you just need to enter:

1. His model.
2. Car brand.
3. Modification and generation.

The battery selection for the car is done automatically. To do this, you just need to click a couple of times. The following will be a list of batteries with information about each model.

Why is it important to choose a battery according to the make of your car?

If the selection of the battery according to the make of the car is not made correctly, this can lead to many problems. For example, the operation of the machine’s electrical system will be disrupted. There may also simply not be enough current to start the engine and crank the starter, especially when the temperature outside is sub-zero.

Correct selection of batteries for the car guarantees that the car’s equipment will work normally after installing the battery.

About motors

The LF481Q3 engine is manufactured in China; according to reviews from car owners, it is a reliable, easy-to-maintain engine. The engine displacement is 1587 cm3, which is quite enough for safe driving in the city and on busy highways.

It has an in-line arrangement of four cylinders. The operation of each cylinder is ensured by two valves in the intake tract and two valves in the exhaust gas outlet. The valve is driven by two camshafts, which are installed in the cylinder head.

The motor can develop a power of 78 kW. The combustion chamber is wedge-shaped to ensure efficient combustion of the fuel mixture.

There are no hydraulic compensators on this engine; the thermal clearances are adjusted by selecting and installing cup-shaped pushers between the valve and the camshaft protrusion. The timing mechanism of this motor is driven by a toothed belt. The machine can also be equipped with an LFB479Q engine, which has a displacement of 1800 cm 3 and develops a power of 128 hp. With.

Do Lifan valves bend?

This question arises for many car owners who have heard about problems when the belt breaks on other car models. I would immediately like to reassure them that this does not happen on this power unit. This engine is based on the Japanese Toyota 4A-EF, purchased under license. Its designers eliminated the possibility of damage to the valves when the timing belt breaks. This positive quality was adopted by engineers from China. If we talk about engines with a displacement of 1800 cm3, then according to experts, damage to the valves is possible in rare cases. This mainly happens when the engine is running at high speeds.