How to choose the best lamp for low beam headlights on a Lada Largus

Driving safety largely depends on the condition of the head optics. Failure of any element impairs the driver's visibility of the roadway at night, increasing the risk of an emergency. The maximum load is experienced by the low beam lamp, which is the first to fail. Replacing a lamp requires skills, knowledge of the procedure and the availability of a spare light bulb that is suitable for all parameters. Let's look at the selection and installation procedure using the Lada Largus car as an example.

Lada Largus lamps

Lamps used on the Lada Largus passenger car:

  • -Lamp for high and low beam headlights - H4 (AKG 12-60+55) 60/55 W;
  • -Front direction indicator bulb - PY21W (A12-21-4) 21 W;
  • - Side light electric lamp - W5W (A12-5-2) 5 W;
  • -Electric fog lamp - H11 55 W;
  • -Side turn signal lamp - WY5W 5 W;
  • -The turn signal bulb in the rear light is PY21W (A12-21-4) 21 W;
  • -Electric lamp for side light and tail light brake signal - P21/5W (A12-21+5) 21/5 W;
  • -Electric fog light lamp in the rear light - P21W (A12-21-3) 21 W;
  • - Rear light bulb for reversing light - P21W (A12-21-3) 21 W;
  • -Rear additional brake light bulb - P21W (A12-21-3) 21 W;
  • -Electric lamp for license plate lighting - W5W (A12-5-2) 5 W;
  • -Trunk light bulb - W5W (A12-5-2) 5 W;
  • -Interior lamp bulb - W5W (A12-5-2) 5 W;
  • -Electric lamp for individual lighting - W5W (A12-5-2) 5 W;
  • -Glove compartment lighting lamp - W5W (A12-5-2) 5 W;
  • -Light bulb for lighting the cigarette lighter socket - W1.2W (A12-1.2) 1.2 W;
  • -Electric lamp for illuminating the ventilation, heating and air conditioning control unit in the vehicle interior - W1.2W (A12-1.2) 1.2 W;
  • -Hazard light switch illumination lamp - W1.2W (A12-1.2) 1.2 W;

Do-it-yourself replacement of lamps in Lada Largus

Any light bulb in this car can be replaced without a visit to the service center literally on the street. You don't even need a special tool for this. The only thing you may need is a flathead screwdriver to remove the lampshades. It is not necessary to remove the headlights.

Replacing lamps in the headlight of Lada Largus

To change the low beam and high beam bulbs, you must:

  1. Remove the plastic cover.
  2. Disconnect the electrical connector.
  3. Remove the rubber boot of the lamp.
  4. Disconnect the spring clip.
  5. Pull out the lamp.
  6. Install the new lamp and reassemble everything in reverse order.

After completing the replacement, it is recommended to adjust the cut-off line of the low beam headlights.

Replacing the turn signal lamp is carried out as follows:

  1. Remove the electrical connector by lifting the latch.
  2. Turn the socket clockwise or counterclockwise (depending on the headlamp) and remove it from the lamp housing.
  3. Remove the lamp by pressing and turning it counterclockwise.
  4. Reassemble in reverse order.

The marker lamp is easier to pull out - you just need to turn the lamp socket counterclockwise and remove the lamp from the socket by simply pulling it up.

Attention! Do not touch lamp bulbs with your hands, as grease on the surface of the glass will reduce its service life.

How to replace light sources in Largus taillights

To change the rear light bulbs on a Lada Largus, you need to remove the light from the car.

To do this, open the tailgate and unscrew the two plastic nuts securing the light. After which you can dismantle it and perform all the necessary manipulations:

  1. Remove the electrical connector from the lamp.
  2. Press out the three plastic latches securing the board with lamps.
  3. To replace any of the lamps on the board, press it and turn it counterclockwise.
  4. Install a new lamp and reassemble in reverse order.

Similar operations are performed for the lamp on the other side of the body.

Replacing fog lamps on Lada Largus

It is more convenient to replace by removing the front bumper from the corresponding fender liner.

To do this, you need to unscrew two T20 screws, and then unfasten the bumper from the latches. Next we perform the following operations:

  1. We put our hand inside the bumper and unfasten the connector from the lamp.
  2. Turn the lamp counterclockwise and pull it out of the PTF housing.
  3. We install the new lamp in the reverse order and screw the fender liner to the bumper.

To make it easier to replace the light bulb, it is recommended to rotate or remove the wheel for easier access.

How to change a side repeater lamp

Largus has turn signal repeaters mounted on the front fenders. You can do this by doing the following:

  1. Using plastic or cardboard plates, we squeeze the repeater mounting clamps on both sides.
  2. Remove it from the wing.
  3. Turn the cartridge counterclockwise and remove it from the housing.
  4. Pull the lamp up and remove it from the socket.
  5. Install the new lamp in the reverse order of removal and reassemble.

There is another replacement method. To release the repeater housing clamps, you need to remove the fender liner. However, this method is not very convenient.

Replacement of license plate lamps in Largus

There is nothing difficult about replacing this light source. Just take a T20 Torx and unscrew the screw securing the diffuser.

Next, you just need to pull it out and replace the lamp inside the bumper by pulling it out of the socket. Install a new one in its place and screw the diffuser back.

How to change interior lamps in Largus

The interior of this car only supports the following lights:

  • trunk;
  • glove box;
  • lampshade;
  • heater control unit.

To remove the interior light bulb, use a flat-head screwdriver to remove the lamp diffuser, then remove the required bulb and install a new one.

The trunk has exactly the same lamp, and therefore the replacement of light sources occurs in exactly the same way.

In the glove compartment, simply pry up the lampshade using a screwdriver. It will fall out and the lamp can be replaced by removing it from the socket.

Replacing the lamp in the heater control unit is carried out as follows:

  1. Using a plastic puller, unfasten the center console trim.
  2. Place your hand inside the panel and feel the base on the back of the block.
  3. Rotate the desired base 45 degrees and pull it out.
  4. Replace the lamp on it and reassemble in the reverse order.

This completes the replacement of interior lamps.

Headlight bulbs

Low and high beam headlight lamp

Light bulb type:

Designation of high and low beam headlight bulbs according to EEC - H4

Technical characteristics of Llama H4 high and low beam headlights:

  • Power - 60/55 W;
  • Light - xenon;
  • The base is metal;
  • The base is round;
  • The color of the flask is transparent;

Dimensions of the H4 lamp for low and high beam headlights Lada Largus

  1. The diameter of the flask is 17 mm;
  2. The size from the tip of the flask to the seat is 60 mm;
  3. Lamp height - 92 mm;
  4. Base diameter - 43 mm;
  5. Base height - 32 mm;

The installation location of the H4 lamp for high and low beam headlights is shown in the figure below:

The car has two such H4 bulbs.

Front turn signal lamp Lada Largus

Design of the front turn signal lamp in the headlight unit:

ECE light bulb designation: PY21W

Technical characteristics of the front turn signal lamp:

  • Lamp - incandescent;
  • Power - 21 W;
  • The color of the flask is red;
  • The base is metal;
  • The base is round.

Dimensions of the PY21W turn signal lamp in the headlight of Lada Largus

  1. The diameter of the flask is 26×5 mm;
  2. Lamp height - 52.5 mm;
  3. Base diameter - 17 mm;

The installation location of the PY21W front turn signal lamp for Lada Largus is shown in the figure below:

Side light unit light bulb

Design of the W5W side light lamp in the headlight unit:

ECE light bulb designation: W5W

Technical characteristics of the side light lamp in the headlight unit:

  • Lamp - incandescent;
  • Power - 5 W;
  • The color of the flask is transparent;
  • Base - glass;

Dimensions of the W5W side light bulb for the Lada Largus headlights

  1. The diameter of the flask is 10.3 mm;
  2. The size from the tip of the flask to the seat is 20.7 mm;
  3. Lamp height - 26.8 mm;
  4. Base diameter - 9.5 mm;
  5. Base height - 6.1 mm;

The installation location of the W5W lamp for the side light headlight block of the Lada Largus is shown in the figure below:

Conclusion

People who often operate their vehicle at night must adhere to the basic rules for adjusting headlights. This is done so that this seemingly insignificant detail does not become the cause of a serious accident.

Lada Largus is a popular family multi-purpose station wagon, mass production of which was launched by AvtoVAZ PJSC in 2012.

A car of this class is designed to meet the most diverse needs of potential buyers and can be used for both everyday and long-distance trips. At the same time, it feels great in urban conditions and on country roads.

The universal use of this car quite often contributes to damage to the elements of the front optics by stones flying from under the wheels of oncoming or passing vehicles, branches of low-growing bushes, etc.

Replacing damaged head optics and installing new elements is not difficult and can be carried out by almost any car owner, even those without experience in carrying out such work. The only difficulty with this is the need to dismantle the front bumper, where not only fog lights are integrated, but also headlights.

Largus fog lamp

H11 Fog Light Bulb Design:

EEC light bulb designation: H11

Technical characteristics of the H11 fog lamp lamp:

  • Lamp - halogen;
  • Power - 55 W;
  • The flask is transparent;
  • The base is plastic;
  • The base is an individual design;

Dimensions of the H11 lamp for the fog lamp of the Lada Largus

  1. The diameter of the flask is 11 mm;
  2. The size from the tip of the flask to the seat is 43 mm;

The installation location of the H11 lamp for the Lada Largus fog light is shown in the figure below:

How to quickly replace PTF?

If the light fixtures we are considering are damaged, then replacing the fog lights will not take much time. Next, we will provide instructions using the example of the left PTF, since all manipulations with replacing the right headlight will be absolutely identical.

We use a Phillips screwdriver as a tool for work.

We operate from under the LADA Largus car quickly without dismantling the front bumper.

  1. First we remove the front fender liner (left).
  2. We press out the latch that holds the cable harness block.
  3. We remove the block itself from the base terminal of the headlight.
  4. Next, unscrew the three screws that hold the PTF in the bumper seat.
  5. We take the headlight out and put it aside.
  6. We install a new lighting device into the resulting niche.
  7. We connect the PTF to the network and check the functionality.
  8. We return the fender liner to its original place.
  9. If necessary, adjust the light beam.

Side turn signal lamp

Design of WY5W red side turn signal lamp:

EEC light bulb designation - WY5W

Specifications of WY5W side turn signal lamp:

  • Lamp - Incandescent;
  • Power - 5 W;
  • Color - red;
  • Base - glass;
  • The base is flat.

Dimensions of the WY5W side turn signal lamp for Lada Largus

  1. The diameter of the flask is 10.3 mm;
  2. The size from the tip of the flask to the seat is 20.7 mm;
  3. Base width - 9.5 mm;
  4. Base thickness - 2.1 mm;
  5. Lamp height - 26.8 mm;

The installation location of the WY5W side turn signal lamp for the Lada Largus is shown in the figure below:

High beam headlight

The lamp is not accessible from the engine compartment, so replace the lower part.

  1. Remove the wheel arch trim by unscrewing the screws;
  2. Remove the lamp cartridge by turning it clockwise (right. counterclockwise);
  3. Remove the cartridge from the cartridge without the lamp.

remove the wheel arch trim Lada Largus Lada Largus replacement light bulb Lada Largus replacement light bulb

Install the new lamp in reverse order.

Tail light bulbs

Turn signal lamp in rear light

Design of the PY21W turn signal lamp in the red rear light:

ECE light bulb designation - PY21W

Technical characteristics of the PY21W turn signal lamp in the rear light:

  • Lamp - incandescent;
  • Power - 21 W;
  • Color - red;
  • The base is metal;
  • The base is round.

Dimensions of the PY21W turn signal lamp in the rear light of Lada Largus

  1. The diameter of the flask is 10.3 mm;
  2. The size from the tip of the flask to the seat is 20.7 mm;
  3. Base width - 9.5 mm;
  4. Base thickness - 2.1 mm;
  5. Lamp height - 26.8 mm;

Installation location of the PY21W turn signal lamp in the rear light of Lada Largus:

Electric lamp of dimensions and brake signal Largus

Design of the P21/5W lamp of the dimensions and brake light of the rear light:

EEC light bulb designation - P21/5W

Technical characteristics of the P21/5W lamp of dimensions and brake light in the rear light:

  • Lamp - incandescent;
  • Power - 21/5 W;
  • The color of the flask is transparent;
  • Filaments - 2 pcs;
  • The base is metal;
  • The base is round.

Dimensions of the P21/5W stop lamp and dimensions in the rear light of the Lada Largus

  1. The diameter of the flask is 26.5 mm;
  2. The size from the tip of the flask to the seat is 45 mm;
  3. Lamp height - 52.5 mm;

Installation location of the P21/5W lamp for the dimensions and brake light in the rear light of the Lada Largus:

Tail light fog lamp

P21W Tail Fog Light Bulb Design:

Lamp designation according to ECE - P21W

Specifications of P21W tail light fog light bulb:

  • Lamp - incandescent;
  • Power - 21 W;
  • The color of the flask is transparent;
  • The base is metal;
  • Filament - 1 pc.

Dimensions of the P21W fog light lamp in the rear light of Lada Largus

  1. The diameter of the flask is 26.5 mm;
  2. The size from the tip of the flask to the seat is 45 mm;
  3. Lamp height - 52.5 mm;

Installation location of the P21W fog light lamp in the rear light of the Lada Largus:

Reversing light bulb

Design of P21W tail light reversing light bulb:

Lamp designation according to ECE - P21W

Technical characteristics of P21W rear light bulb:

  • Power - 21 W;
  • Color: transparent;
  • The base is metal;
  • Filament - 1 pc.

Dimensions of the P21W reverse lamp in the rear light of Lada Largus

  1. The diameter of the flask is 26.5 mm;
  2. The size from the tip of the flask to the seat is 45 mm;
  3. Lamp height - 52.5 mm;

Installation location of the P21W reversing light lamp in the rear right lamp of the Lada Largus:

Video from Loganovoda about replacing steering tips

Replacing the steering tip for Renault Logan, Sandero, Lada Largus

Replacing the steering rod for Renault Logan, Sandero, Largus, Logan2, Sandero2

Knocks on tie rod ends in Dacia Logan, Sandero, check and replacement

Renault Logan, Sandero! Replacement of ball and steering joint!

Review of the FENOX steering rack for Renault Logan and Largus

Using a screwdriver, prying up the decorative trim, moving upwards in the assembly with the fan, now you need to loosen the tightening of the clamps, disconnect all the hoses from the radiator, unscrew the bolts, replace steering tips on the Lada Largus, nuts that secure the casing with the fan and the radiator, disconnect the casing with the fan, you need to remove the two lower mounting pads from the radiator. In most cases, it is not necessary to completely cut the nut. Because, as has already been tested in practice, a standard rear shelf can fail and cannot support good music speakers.

If you are changing spark plugs for the first time on a new car, use a wheel wrench and some machine oil. After an accident, the most important structural part of the car undergoes changes; the geometry is disrupted, visible and invisible flaws appear, and the coordinates of the installation locations of body elements are shifted. You can check its performance by blowing it with your mouth.

If this does not happen, remove the fastening pins from the holes in the upholstery. A standard heater will provide heat in winter, but in summer you will really get sick if the temperature breaks. If the mass is bad, it will not be 0 volts at all. However, their barriers may differ significantly. Now the only thing left to do is to connect the levers of the racks to the tips and tighten all the fasteners. Buying disc brakes and simply installing them, without following clear rules, is dangerous and not recommended. The high physical and chemical properties of this material make it possible to produce many automotive accessories with unique functional properties. And the loads thanks to the airbag are small. Over the past year since the Solaris crash test, a lot has changed in the Czech laboratory 8212 it now belongs to Skoda, and acts as a subcontractor. You can even wash the box, but do it only from the outside.

Sources

  • https://www.autosecret.net/rulevoe-upralenie/1389-zamena-nakonechnika-rulevoj-tjagi
  • https://carfrance.ru/menyaem-rulevye-nakonechniki-na-reno-logan-svoimi-rukami/
  • https://avtolars.ru/lada-largus/v58018-zamena-rulevih-nakonechnikov-lada-largus.php

Additional brake light lamp Largus

Design of lamp P21W additional brake light:

Lamp designation according to ECE - P21W

Technical characteristics of the P21W additional brake light lamp:

  • Power - 21 W;
  • Color: transparent;
  • The base is metal;
  • The base is round.

Dimensions of the P21W additional brake light lamp for Lada Largus

  1. The diameter of the flask is 26.5 mm;
  2. The size from the tip of the flask to the seat is 45 mm;
  3. Lamp height - 52.5 mm;

Installation location of the P21W additional brake light lamp for Lada Largus:

Mid and high beam

One lamp is responsible for low and high beam. Its resource is 2000-4000 hours. To access the left headlight, remove the battery.

  1. Turn the cap counterclockwise;
  2. Remove the cover by releasing the lock.

replacing low and low light bulbs Lada Largus replacing low and low light bulbs Lada Largus

  1. Remove the socket from the wires by clicking the lock;
  2. Remove the rubber cover by pulling on the edge.

replacing low and low light bulbs Lada Largus replacing low and low light bulbs Lada Largus

  1. Disconnect the lamp assembly clamps;
  2. Remove the headlight.

replacing low and low light bulbs Lada Largus replacing low and low light bulbs Lada Largus

Electric license plate lamp

W5W license plate lamp design:

Lamp designation according to ECE - W5W

Technical characteristics of the license plate lamp W5W:

  • Power - 5 W;
  • Color: transparent;
  • Base - glass;
  • The base is flat.

Dimensions of the W5W lamp for the license plate light of the Lada Largus

  1. The diameter of the flask is 10.3 mm;
  2. The size from the tip of the flask to the seat is 20.7 mm;
  3. Lamp height - 26.8 mm;
  4. Base width - 9.5 mm;
  5. Base thickness - 2.1 mm;

Installation location of the W5W lamp for the Lada Largus license plate light:

What to do if the fog lights still don't light up

It often happens that the reason for the failure of the fog light is not a burnt out lamp. What else could cause such a malfunction? There are few such options:

  1. A power surge in the on-board network that caused a fuse to blow . Typically this problem is caused by poor contact between the terminals of the battery, generator, or when turning on/off a powerful load. Eliminated by replacing the fog light fuse with a new one with the same rating.
  2. Oxidation of PTF power terminals and blocks . Identified by visual inspection. All power supplies are disconnected, the contacts are inspected and if there is any foreign deposits, they are cleaned.
  3. Short circuit . It may be caused by the insulation of the PTF supply wire rubbing against the body and shorting to it. In this case, as a rule, the fuse burns out, and replacing it with a new one leads to the same result. The malfunction can be eliminated by visual inspection of the wiring harness supplying the PTF, followed by isolating the damaged area.
  4. Broken power wire . Power wires can either break due to vibration or burn out when shorted to the body. In the latter case, the fuse usually blows. If the new fuse does not blow, but the fog light still does not light, you need to inspect the wiring harness, find and repair the break.

Trunk light for Lada Largus

Design of the W5W trunk light bulb:

Lamp designation according to ECE - W5W

Technical characteristics of the W5W trunk lighting lamp:

  • Power - 5 W;
  • Color: transparent;
  • Base - glass;
  • The base is flat.

Dimensions of the W5W lamp for lighting the trunk of the Lada Largus

  1. The diameter of the flask is 10.3 mm;
  2. The size from the tip of the flask to the seat is 20.7 mm;
  3. Lamp height - 26.8 mm;
  4. Base width - 9.5 mm;
  5. Base thickness - 2.1 mm;

Installation location of the W5W lamp for lighting the trunk of the Lada Largus:

Headlights.

I can drive up to you, look at my light, try it. If it suits you, I will recommend the lamps. Edited: 1 time (Last: January 22, 2013 at 15:56) Konstantin Kazanets St. Petersburg Rating: 881 08/24/2012 Club member Messages: 1202 Write a private message Lada Largus 7 seats 16V so they are regulated! So I ask - how? let's live - we'll see, we'll live - we'll find out, we'll survive - we'll take it into account.www.citilink.ru kutj066 St. Petersburg Rating: 3364 04/29/2012 Club member Messages: 3105 Write a private message Lada Largus 7 seats 16V Dmitry Amursky, thanks for the correction! I admit, I made a mistake... Not light temperature, but color temperature. Konstantin alex Gatchina Rating12 Messages: 2160 Write a private message Well, at least one more person has “seen the light” :)) PS: studying Physics and Chemistry, a little more than the school curriculum, is our EVERYTHING.

Interior light bulb

Design of the W5W lamp for the interior lighting:

Lamp designation according to ECE - W5W

Technical characteristics of the W5W lamp for the interior lighting:

  • Power - 5 W;
  • Color: transparent;
  • Base - glass;
  • The base is flat.

Dimensions of the W5W lamp for the interior lighting of the Lada Largus

  1. The diameter of the flask is 10.3 mm;
  2. The size from the tip of the flask to the seat is 20.7 mm;
  3. Lamp height - 26.8 mm;
  4. Base width - 9.5 mm;
  5. Base thickness - 2.1 mm;

Installation location of the W5W lamp for the interior lighting of the Lada Largus:

Lamp for individual lighting of Lada Largus

Design of the W5W lamp for individual lighting:

Lamp designation according to ECE - W5W

Technical characteristics of the W5W lamp for individual lighting:

  • Power - 5 W;
  • Color: transparent;
  • Base - glass;
  • The base is flat.

Dimensions of the W5W lamp for the individual lighting of the Lada Largus

  1. The diameter of the flask is 10.3 mm;
  2. The size from the tip of the flask to the seat is 20.7 mm;
  3. Lamp height - 26.8 mm;
  4. Base width - 9.5 mm;
  5. Base thickness - 2.1 mm;

Installation location of the W5W lamp for the individual lighting of the Lada Largus:

Electrical lamps of the instrument panel

Glove box light bulb

Design of the W5W glove box light bulb:

Lamp designation according to ECE - W5W

Technical characteristics of the W5W lamp for the glove compartment light:

  • Power - 5 W;
  • Color: transparent;
  • Base - glass;
  • The base is flat.

Dimensions of the W5W lamp for the glove compartment lighting of the Lada Largus

  1. The diameter of the flask is 10.3 mm;
  2. The size from the tip of the flask to the seat is 20.7 mm;
  3. Lamp height - 26.8 mm;
  4. Base width - 9.5 mm;
  5. Base thickness - 2.1 mm;

Installation location of the W5W lamp for the glove box lighting of the Lada Largus:

Cigarette lighter lamp for Lada Largus

Design of W1.2W cigarette lighter lamp:

Lamp designation according to ECE - W1.2W

Technical characteristics of the W1.2W cigarette lighter lamp:

  • Power - 1.2 W;
  • Color: transparent;
  • Base - glass;
  • The base is flat.

Dimensions of the W1.2W cigarette lighter lamp for Lada Largus

  1. The diameter of the flask is 5 mm;
  2. The size from the tip of the flask to the seat is 14.5 mm;
  3. Lamp height - 20 mm;
  4. Base width - 5 mm;

Installation location of the W1.2W lamp for the cigarette lighter illumination of the Lada Largus:

Electric lamps for illumination of the ventilation, heating and air conditioning control unit

Design of the W1.2W lamp for illuminating the ventilation, heating and air conditioning control unit:

Lamp designation according to ECE - W1.2W

Technical characteristics of the W1.2W lamp for the ventilation, heating and air conditioning control unit:

  • Power - 1.2 W;
  • Color: transparent;
  • Base - glass;
  • The base is flat.

Dimensions of the W1.2W lamp of the control unit for ventilation, heating and air conditioning Lada Largus

  1. The diameter of the flask is 5 mm;
  2. The size from the tip of the flask to the seat is 14.5 mm;
  3. Lamp height - 20 mm;
  4. Base width - 5 mm;

Installation location of the W1.2W lamp for the control unit for ventilation, heating and air conditioning Lada Largus:

Item number in the pictureExplanation of the position in the picture of the Lada Largus climate control unitVAZ catalog number
1 Ventilation and heating control panel 275109032R
2 Heater block 6001547669
3 Pan head screw 7703017130

Lamps for foglights - delivery of parts to VAZ

You can order Largus fog lamps from us with delivery in Moscow and the region. The PTF uses a lamp with an H11 12v 55w socket. Depending on the purpose, you can install lamps on Largus cars:

  1. Regular halogen.
  2. With increased light output.
  3. Under xenon.
  4. LED.

On Largus, the PTF is equipped with Philips Eco Vision lighting elements with an increased service life. It is possible to install Philips or Osram elements with increased light output; they will illuminate the roadway more efficiently. If a car owner wants to get the xenon effect, it is necessary to install electric lamps with a blue bulb, which will create a bright white light with a glow temperature of 4500-5000 K. To adapt foglights as an alternative to DRLs (this is real and quite possible), LED electric lamps should be installed. They will not be able to completely illuminate the road space, but as an alternative to running lights, they are what is needed. If you find it difficult to choose a product yourself, contact the professionals of our company. The specialist will place the order and, if possible, provide a discount.

Rating
( 1 rating, average 5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]