Location of engine and body number on Lada Kalina

The Lada Kalina family of cars includes the VAZ-1118 with a four-door sedan body and the VAZ-1119 with a five-door hatchback body. The vehicles belong to an especially small class (class B according to the international classification) and are designed for operation at ambient temperatures from -40 to +45 °C on public roads with hard surfaces. Lada Kalina cars are equipped with an 8-valve engine of the VAZ-21114-50 model with a displacement of 1.6 liters (factory vehicle modification indices - VAZ-11183 and VAZ-11193) and a 16-valve engine of the VAZ-11194 model with a displacement of 1.4 liters (factory car modification indices - VAZ-11184 and VAZ-11194). Both engines are located across the engine compartment and are equipped with a distributed fuel injection system and a catalytic exhaust gas converter, structurally made in a single block with the exhaust manifold.

The body is monocoque, all-metal, of welded construction with hinged side doors, front fenders, hood and trunk lid (tailgate). The transmission is made according to a front-wheel drive system with drive wheels of different lengths. The front suspension is independent, spring, with anti-roll bar, with hydraulic shock absorber struts. The rear suspension is dependent, lever-spring, with hydraulic shock absorbers. The front wheel brakes are disc brakes with a floating caliper, the rear wheels are drum brakes. The steering is safety-resistant, with a rack-and-pinion steering mechanism and an electric booster. Lada Kalina cars are equipped with a remote control system for locking or unlocking side door locks (in a variant, also locking the trunk lid or tailgate lock) with simultaneous activation or deactivation of the vehicle security mode. In addition, provision is made for remote activation of alarm systems in case of violations of vehicle security zones and blocking of all side rails (in the optional version - the rear) by pressing a button from inside the car. The overall dimensions of the VAZ-2118 car are shown in Fig. 1.1, VAZ-2119 car in Fig. 1.2, technical characteristics in table 1.1. Elements of the engine compartment of the Lada Kalina car are shown in Fig. 1.3 and 1.5. The location of the main components and assemblies of the car is shown in Fig. 1.6)

Rice. 1.1 Overall dimensions of the VAZ-2118 car

Passport details of Lada Kalina

In the engine compartment there are: A - body identification number; B - identification mark; B - engine model and number. Identification number (For the vehicle, engine model, name of the manufacturer, year of manufacture and certification information are given in the identification plate (Fig. 1.4).

The vehicle identification number is stamped on the right shock absorber support in the engine compartment on the strut.

Interior and engine compartment space

All doors, hood and trunk lids should open without jerking. The hood must be pressed against the body in the closed position. The spare wheel, wheel wrench and jack are always kept in the luggage compartment. Having verified this, proceed to inspect the engine compartment:

  • Check the level of antifreeze, as well as brake fluid (the body of the tanks is made translucent);
  • Check the level of engine oil and gearbox oil (use a dipstick);
  • You can pay attention to the release date of the battery. The numbers will be printed on top of the negative terminal or on the battery body.

Note that now some factories do not explicitly print the battery production date. Instead, special code is used.


The numbers 309 mean the following: third month, 2009

Of course, it would be advisable to check the engine and body number with the values ​​indicated on the PTS coupon. In Kalina-2, all the numbers need to be looked for under the hood:


The three most important signs

The following elements are indicated in the figure:

  1. Engraving with body number;
  2. Engine number plate;
  3. Pivot table with general data.

Inside the car, they check whether the main blocks and components can be adjusted:

  • Front seats;
  • Front seat head restraints;
  • The rear seats should fold easily;
  • The steering column should move up and down and lock into place;
  • Air duct guides should be easy to adjust;
  • The mirrors are adjusted with special levers.

It is necessary to check whether each of the seat belts is securely fixed in the connector. You can also try shifting the gearshift knob without starting the engine.

The serviceability of seat belts is checked as follows: the belt is pulled sharply, after which the tightening mechanism is activated.

Lada Kalina engine number

Electrical diagram of Lada Kalina

The electrical circuit of the Lada Kalina car has several systems and main elements. Any of them is responsible for certain functions. These systems include: lighting circuitry, ignition circuitry, engine control, functions and sound signals for additional comfort.

The article talks about the Lada Kalina engine number, compiled from the experience and opinion of car owners.

If any element of the electrical system fails, the entire circuit stops working properly, so it is fundamentally important to monitor its integrity and promptly replace worn elements. Circuit operation order

Circuit operation order

As previously reported, the entire electrical circuit receives power from the battery. When the ignition is turned on, voltage is supplied to the positive terminal and turns on the entire electrical circuit. Devices important for engine control remain without power.

Engine operation diagram

After the engine of the Lada Kalina car is started, current from the battery flows to the ignition coil, through the rectifier, and causes a spark to appear. Then the generator comes into operation and ensures uninterrupted operation of all electrical equipment while the engine is running.

All electrical appliances of the Lada Kalina car are connected to the power supply through the fuse box. Any device has its own maximum permissible current.

If this mark is exceeded in total, the fuse of the device burns out, at the same time preserving the device itself.

You can read the latest news about the Lada Kalina engine number on the domestic website soon.

An enormous amount of energy is consumed by the engine equipment circuit. It includes such details as: starter, generator, immobilizer, ignition switch, electric fuel pump and resistor.

Less energy is spent on lighting devices. Considering that, unlike the engine, they do not work uninterruptedly, they actually do not affect the battery charge. The lighting devices of the Lada Kalina include: high beam and low beam lamps, direction indicators, side lights, brake lights, reverse lamp, device panel lighting, indicator lamps, interior lamps, trunk, engine compartment and glove compartment lighting.

This whole circuit has many connections between elements. These connections occur through coils (to transform the current) and fuses (to prevent the entire circuit from shorting).

Also, the electrical circuit of the Lada Kalina car includes increased comfort devices. These include: electric windows, cigarette lighter, alarm, electric locks, acoustics, gasoline, oil, brake and transmission fluid level sensors, heated seats, glass, etc.

All elements of the car's electrical circuit are completely protected from combustion and short circuits. Since often, when electric current passes through a rectifier, the voltage in the circuit changes. This happens especially quite often when the engine runs on only one generator. Under such conditions, the battery does not maintain a constant voltage, and it always increases at high speeds and decreases at idle.

Informational and entertaining video about the engine number of the Lada Kalina, the best moments and comments from the presenters.

Characteristics of motor 11183

The official AvtoVAZ manual contains a description of the parameters of the ICE 11183, according to which the technical characteristics are as follows:

ManufacturerAvtoVAZ
Engine brand11183
Years of production2004 – …
Volume1596 cm3 (1.6 l)
Power60 kW (82 hp)
Torque moment120 Nm (at 2700 rpm)
Weight112 kg
Compression ratio9,8
Nutritioninjector
Motor typein-line
Injectionelectronic multipoint
Ignitionmodular
Number of cylinders4
Location of the first cylinderTVE
Number of valves on each cylinder2
Cylinder head materialaluminum alloy
Intake manifoldplastic receiver, electronic throttle
An exhaust manifoldcombined with catalyst
Camshaftfrom 21114
Cylinder block materialcast iron
Cylinder diameter82
Pistonsordinary
Crankshaftoriginal with increased crank stroke
Number of main bearings5
Piston stroke86 mm
FuelAI-92-95
Environmental standardsEuro-3
Fuel consumptionhighway – 6.2 l/100 km
combined cycle 7.6 l/100 km

city ​​– 8.8 l/100 km

Oil consumption0.5 l/1000 km
Engine oil for 111835W-30 and 10W-40
Engine oil volume3.5 l
Operating temperature95°
Motor lifedeclared 150,000 km,
real 300,000 km
Adjustment of valveswashers between camshaft cams and tappets
Cooling systemforced, antifreeze/antifreeze
water pumpplastic impeller
Candles for 11183BPR6ES, A17DVRM
Gap between spark plug electrodes1.1 mm
Timing beltGates
Cylinder operating order1-3-4-2
Air filterNitto, Knecht, Fram, WIX, Hengst
Oil filtercatalog number 90915-10001
replacement 90915-10003, with check valve
Flywheelfrom 2110
Valve stem sealscode 90913-02090 inlet light
code 90913-02088 exhaust dark
Compressioncylinder pressure from 13 bar nominal
XX speed800 – 850 min-1
Tightening force of threaded connectionsspark plug – 18 Nm
flywheel – 62 – 87 Nm

clutch bolt – 19 Nm

bearing cap – 68 Nm (main) and 53 (rod)

cylinder head – three stages 29 Nm, 49 Nm and 90°

The operating manual from the manufacturer includes information on lubricants and coolants. In particular, for these engines it is recommended:

which oil to choose among the variety of fuel and lubricants manufacturers - ZIK, Total Quartz;


Installation 11183 under the hood

Mark detection problems

During operation, the motor is necessarily covered with a layer of dirt.
It does not allow you to quickly see the numbering of the unit. Therefore, experienced car owners are advised to always clean the engine and wash it. Some manufacturers place the engine markings in a place where they can only be seen using a small mirror. For example, in a Ford car, it is stamped on the very bottom panel , right under the attached oil filter. It is enough to lower the small mirror and the markings become clearly visible, and you can do without removing the protection.

Purpose of number verification

An inexperienced owner is unlikely to be able to quickly indicate the engine number on a Kalina, but everyone should be able to do this. Please note that only factory markings indicate the quality of the car and engine. For this reason, government officials trust only this information when checking and identifying a car; the number requires careful handling.

Engine VAZ 11194 (16 valves):

Body and external accessories

Before buying a car, always check for scratches on the paintwork. It would be better to add the following to this action:

Even before starting the engine, try unscrewing the tank cap and then install it in place.

The plastic stopper additionally holds the cord

As you continue to inspect the vehicle, you can pay attention to the following elements:

Finally, try folding both mirrors located on the outside of the body. If it is determined that everything is in order with the mirrors, you can proceed to inspect the interior.

In the rear doors of the Kalina-2/Granta family of vehicles, a mechanism is installed that allows you to block the door from being unlocked from the inside. On the front side there is a lever that rotates 45 degrees. On the left door the lever is turned to the left, on the right door - clockwise. This is how the serviceability of the locking mechanism is checked.

Decoding the VIN code of Kalina

The transcript looks like this.

  1. XTA is the international designation of the manufacturer.
  2. 111930 – part of the code indicates the car model.
  3. 7 – a changing segment indicating the year of manufacture of the car. in this case it is 2007.
  4. 0014223 – the last part of the code always indicates the serial number of the body under which it came off the assembly line. The number for each car is individual and is the most important part of the vehicle passport.

To avoid the possibility of cutting the damaged car and its further use, the manufacturer duplicates the number on the rear right arch. Both codes must be identical.

Lada Kalina repair and operation manual

The Lada Kalina family of cars includes the VAZ-1118 with a four-door sedan body and the VAZ-1119 with a five-door hatchback body. The vehicles belong to an especially small class (class B according to the international classification) and are designed for operation at ambient temperatures from -40 to +45 °C on public roads with hard surfaces. Lada Kalina cars are equipped with an 8-valve engine of the VAZ-21114-50 model with a displacement of 1.6 liters (factory vehicle modification indices - VAZ-11183 and VAZ-11193) and a 16-valve engine of the VAZ-11194 model with a displacement of 1.4 liters (factory vehicle modification indices – VAZ-11184 and VAZ-11194). Both engines are located across the engine compartment and are equipped with a distributed fuel injection system and a catalytic exhaust gas converter, structurally made in a single block with the exhaust manifold.

The body is monocoque, all-metal, of welded construction with hinged side doors, front fenders, hood and trunk lid (tailgate). The transmission is made according to a front-wheel drive system with drive wheels of different lengths. The front suspension is independent, spring, with anti-roll bar, with hydraulic shock absorber struts. The rear suspension is dependent, lever-spring, with hydraulic shock absorbers. The front wheel brakes are disc brakes with a floating caliper, the rear wheels are drum brakes. The steering is safety-resistant, with a rack-and-pinion steering mechanism and an electric booster. Lada Kalina cars are equipped with a remote control system for locking or unlocking side door locks (in a variant, also locking the trunk lid or tailgate lock) with simultaneous activation or deactivation of the vehicle security mode. In addition, provision is made for remote activation of the alarm system in case of violations of vehicle security zones and blocking of all side rails (in the optional version - the rear) by pressing a button from inside the car. The overall dimensions of the VAZ-2118 car are shown in Fig. 1.1, VAZ-2119 car in Fig. 1.2, technical characteristics in table 1.1. Elements of the engine compartment of the Lada Kalina car are shown in Fig. 1.3 and 1.5. The location of the main components and assemblies of the car is shown in Fig. 1.6)

Rice. 1.1 Overall dimensions of the VAZ-2118 car

Engine tuning

To improve the performance of the 11183 engine, several types of tuning can be used:

Practice shows that chip tuning for 8-valve internal combustion engines is not effective, and turbocharging leads to increased wear of parts, so these methods are rarely used.

Thus, the 11183 motor has a serious advantage - it does not bend the valves with pistons when the timing belt drive breaks. However, there are a number of shortcomings that were corrected only in later versions of engines from the manufacturer AvtoVAZ.

Cancel engine verification

In the spring of 2011, a law came into force in our country according to which it is allowed to register a car without checking the make of the unit.

There is no longer a mark on the car's registration documents. The deregistration operation has been greatly simplified; now the presence of the owner is not required, all actions are performed automatically.

If a person sells a car to a person with whom they live in the same area, they are allowed to keep the old license plates .

What to do if the plate with the VIN number of the Lada Vesta is lost due to an accident or repair?

If no crime is found behind the car, then you can go back to check the license plates and register the car.

Rate the article on the website! Your opinion is important to us! (25.00 out of 5)

The Lada Vesta SW Cross blog is a collection of thematic articles in which you will find all the information about the new product of the domestic automobile industry - technical specifications, reviews, configurations and prices, repair and maintenance instructions.

Approximate cost of repair work on the Kalina body at a service station

Here are the prices offered today at various repair services.

Replacement, removal and installation of body partsPrice, rubles
Hood replacement (removal/installation)1800
Front fenders (removal/installation)1600
Front doors (removal/installation)2200
Rear doors (removal/installation)2000
Bumpers (removal/installation)1800
Sedan trunk lid (removal/installation)1900
Replacement of load-bearing body elementsPrice, rubles
Roof panel9000
Wing14 000
Spar11 000
Door threshold9000
Door pillar8000
Slip worksPrice, rubles
Installing the car on a slipway to remove reference points to check the geometry of the body4000

In principle, the prices are not that low. It would be better to learn how to replace (which is much easier) or repair it yourself. We are not talking about competently taking body dimensions to compare geometry. This, of course, should be done only with high-quality equipment, which is almost impossible to provide in a garage workshop.

On the other hand, useful information about the geometric dimensions of Kalina’s bodies will be presented below, which will make it possible to remove them yourself using a regular tape measure.

Watch a video about problem areas of the Lada Kalina body

Rating
( 2 ratings, average 4.5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]