Door trim for VAZ 2110

The four-door VAZ 2110 sedan is the flagship model in the Lada 110 family. The last car rolled off the assembly line in 2007 after a twelve-year production cycle. The door trim of the VAZ 2110 is made of durable, hard plastic, the material is resistant to wear and mechanical damage.

The disadvantage of the door trim is the same type of texture and three types of colors; most drivers prefer to tune the interior and change the trim to a more modern material.

Replacement options

Drivers have several options for replacing door trim, each of which has its own advantages and is chosen based on taste:

Eurocard;
European cladding;
panels from the manufacturer;
independent re-upholstery.

Factory trims from AvtoVAZ are replacement kits for the original trim. They are made of plastic and additionally covered with decorative inserts. The advantages are the exact overall dimensions, ease of installation of clips, and compliance with the door dimensions. Frequently used sheathing kits Lux 1 or Lux 2.

With European cladding, the door lining is made of high-strength polymers and comes in a variety of colors. Manufacturers are small companies specializing in car tuning.

Self-upholstery does not require large investments and is within the capabilities of every driver. The material you can use is textiles, natural, artificial leather, velor, etc.

Tools and materials

To reupholster yourself you will need to prepare:

Sheathing material.
Experienced drivers recommend using vinyl, but keep in mind that the material shrinks significantly. Before purchasing, you must take measurements and leave at least 10 cm for allowances and internal bends. If genuine leather or suede is used, allow up to 5 cm for allowances.
Scissors with a long blade.
Glue. For repairs they use Moment, Master, Titan.
A construction knife with a small blade and a sharp end.
Construction or household hair dryer. It is not recommended to use a heating lamp as it may deform the material.
Glue brushes: thin, wide.
Set of clips.
For the VAZ 2110 they produce special sets of fasteners, the cost of a set of 10 clips is 30 rubles. Each door will require 8 clips. It is recommended to buy latches with a reserve. During installation, several clips often break, since the fasteners are consumer goods and the quality of the fasteners is not regulated.
Self-tapping screws. If you use independent re-upholstery of the cladding on the old casing, then use standard short self-tapping screws; when installing factory casing or Eurocard, purchase a set of long self-tapping screws.
Crosshead screwdriver.
A thin screwdriver with a wide blade.

Lux 2 panels and Euro casings have standard places for speakers with a diameter of 17 cm. If the standard Lada audio system has smaller speakers, then you will need to select it to fit the size of the hole or add a rubber or plastic insert to the part to fit the speaker tightly to the mesh.

You can make payment in one of the ways convenient for you:

By bank cards Visa, Mastercard, Maestro, Mir (including credit cards)

The standard method of paying for an order is using a bank card from any bank. Payments go through the Tinkoff Bank acquiring system (2% commission). ATTENTION! There are restrictions on the amount of payment: 120,000 rubles. After payment you will receive an electronic cash receipt.

Payment using cards Sberbank, VTB, Post Bank, Tinkoff

The most convenient and profitable way to pay for an order for holders. The transfer can be made using a mobile bank or an ATM if you have a card. If you do not use one of the cards of the listed banks, payment can be made at any branch of the relevant bank through an operator or through an ATM, paying in cash. The commission will be from 0% (check with your bank for more detailed information about the commission).

Cash on delivery (payment upon receipt)

Payment is made at the post office upon receipt of the goods. For the cash on delivery service, Russian Post always takes a commission from the order amount.

Note ! Almost all goods can be paid upon receipt (cash on delivery). But in some cases, a partial prepayment in the amount of the DELIVERY COST will be required, namely:

The delivery price is higher than the cost of the ordered goods;

Delivery price by Russian Post is more than 600 rubles;

The order contains items that are made to order (for example, parts painted in body color, stainless steel products and the like)

Yandex money.

Customers who have Yandex.Wallet can quickly and easily pay for an order in our online store, the commission will be 0%.

QIWI wallet.

If it is more convenient for the client to use a QIWI wallet or, if it is not available, to pay through the nearest QIWI terminal, the manager will provide you with the wallet number. Commission 0%. There are restrictions on the payment amount: anonymous wallet 15,000 rubles, registered wallet 60,000 rubles, identified wallet 250,000 rubles.

Buy in credit

Almost all products in the online store vazOriginal.ru can be purchased on credit. This is true for expensive items. Don’t keep yourself waiting, buy goods now and pay for them later and in small amounts.

Payment to a bank account for legal entities and individual entrepreneurs (only without VAT)

This payment method is intended only for legal entities and individual entrepreneurs. After placing your order, send your organization details by email. After this, the manager will send an invoice for payment by email. We work only without VAT.

Dismantling

At a service station, a mechanic spends no more than 15 minutes to disassemble door panels. Self-replacement will go quickly if you adhere to the order of work and do not change the sequence.

Front doors

The work algorithm for the front and rear doors of the VAZ 2110 is slightly different. Before work, you must disconnect the negative terminal from the battery. If the standard trim is reinstalled on the Euro trim, then it is necessary to remove the window lifter lever.

How to remove the front door trim of a VAZ 2110 step by step:

Wrap the screwdriver in a rag or cover the tip with electrical tape.
Using a screwdriver, press the trim of the window handle away from its socket.
Guide the screwdriver so that the panel comes out of the grooves.
Dismantle the cladding and remove the socket.
Using a screwdriver, press out the lock of the driver's door armrest plug.
Remove the clamp.
Unscrew the two screws that hold the handle.
Press the inner handle of the armrest, turn it up, and remove the part.
Unscrew the screw that holds the mirror mechanism and remove it from the lever.
Remove the two fastening clips from their seat and remove the triangular trim.
Carefully slide the screwdriver under the panel and unfasten the 6 clips.

If the driver's or front passenger's door is equipped with a power window, then after removing the handle lock, you need to disconnect the plug.

Rear doors

The differences in work when removing the door trim are based on the fact that power windows are rarely installed for rear row passengers. Removal of the rear door trim is carried out in the following steps:

Use a thin screwdriver to pry the trim on the door handle and remove the part from the grooves.
Unscrew the two bolts located under the trim.
Carefully move the handle to the side, remove it from its seat, and pull it out.
Unscrew the three screws securing the lower rear door trim panel.
Remove the bottom panel.
Unscrew the latch blocking the door from the inside.
Pry off the cladding panel with a screwdriver; you can use a wooden wedge, bend it back and snap off the fastener clips.

The plastic clips must be reinstalled with new ones when assembling the updated door card.

Self-upholstery

Before directly reupholstering, it is recommended to check the condition of the inner door panel, remove pockets of corrosion, check or replace sound insulation, replace rubber seals, so the doors will open better. For VAZ 2110, the service life of door seals is up to 3 years. The process of re-covering a door part yourself step by step:

Clean the outside of the card. You can sand it with fine-grain emery for better adhesion of glue and leather.
Attach the door card to the material, cut around the perimeter, leaving at least 7 cm around the edges.
Treat the outer surface with glue and the inside of the future cladding with glue. Apply glue according to the manufacturer's recommendations. If an adhesive composition is used, then after coating you need to wait up to 10 minutes.
Place the vinyl on the door card, constantly heating the material with a hairdryer, and level the surface so that the leatherette fills all the curves of the part: the space for the speaker, for the central panel, the recesses for the handles.
Cut out all the holes that are covered with vinyl in the door card from the center and not reaching the perimeter, carefully wrap it on the wrong side, making sure that the edges of the fold do not exceed 2-3 cm. Trim off the remaining vinyl.
After gluing the card, trim off the remaining vinyl, leaving at least 3-5 cm on the inside of the card perimeter.

Tuning

After finishing removal, clean the cards from dust using a vacuum cleaner, and begin tuning yourself.

First of all, measure and cut the necessary “patterns” for all door cards, taking into account an allowance of 5 or even 7 centimeters for each side.

This is so that during the process of gluing the sheathing material you do not have to install patches or redo everything all over again.

The glue must be applied to the cards with brushes one at a time so that it has time to dry a little, but not dry out. Having coated the doors with glue, we proceed to the cut piece of vinyl or fabric, which we also coat with glue on the back side, and set aside for 10-15 minutes.

After this time, we proceed directly to gluing the upholstery to the door cards. Vinyl stretches well, filling door “cavities”, but for this it needs to be heated with a hair dryer and smoothed over each cavity and bulge with your hands, preferably with gloves. The edges need to be carefully folded inside out and trimmed.

We subject the remaining doors to the same procedure. In addition, it is advisable to paste the same material over other parts of the interior so that it is in the same style.

These include door handle inlays, the glove compartment lid (if you want to highlight it), triangles at the mirrors, and the top cover of the steering casing. In places of various fastenings, you need to cut small holes using a stationery knife.

When reinstalling, do not forget to replace damaged pistons.

Installation of a ready-made kit

Re-upholstering the cladding yourself does not always help save time or money. If you don’t have time to do this yourself, then you can use ready-made cladding.

The set of door elements Lux 2 from AvtoVAZ has additional sound insulation, a set of standard fasteners, mesh for speakers and screws. Installing a finished panel takes up to 20 minutes for an inexperienced driver. When choosing a casing, choose original replicas; if the set contains only four panels, then the speaker grids, caps and screws must be purchased separately.

The lower part of the door trim needs to be screwed in only with long screws; if the standard kit offers short ones, then you need to change the screws yourself.

Installation of Lux 2 cladding in steps:

Remove the old card.
Attach a new panel, check the gaps and the alignment of the fastener locations.
If the car is equipped with a mechanical window lift, then the panel needs to be modified. Lux 2 does not have a hole for the handle of a mechanical lift.
Secure the trim to the clips.
Tighten all the bolts and secure the outer trim panels.

Delivery by transport company

Advantages:

the cost of delivery of heavy and large-sized orders is much cheaper than that of Russian Post;
There are practically no restrictions on the weight and dimensions of cargo;
There is a wooden crate service - this is an additional guarantee of the integrity of the order.

Disadvantages: unfortunately, there are branches only in cities.

The estimated cost of delivery of an order to the point of delivery of a shopping cart weighing up to 25 kg is 500 rubles.

List of transport companies with which we cooperate:

TC "PEK" (cash on delivery service available);
TC "KASHALOT" (GTD) (cash on delivery service available);
TC "SDEK" (cash on delivery service available);
TC "Business Lines" (shipping with prepayment)
TC "Energia" (shipping with prepayment)
TC “DPD” (shipping with prepayment)
TC "ZhelDorExpedition" (shipping with prepayment)
TC "VOZOVOZ" (shipping with prepayment)
TC "Baikal-Service" (shipping with prepayment)

The cost of delivery is calculated based on the volume, weight of the selected product and the distance from the city of Tolyatti.

TC "Business Lines" - Urgent delivery of goods from 1 kg throughout Russia. The exact cost can be found on the official website of the delivery service - https://www.dellin.ru