How to replace antifreeze on a VAZ 2110: how many liters of antifreeze are included in the cooling system, replacement instructions

During normal engine operation, without overheating, gasket failures and other unexpected troubles, the coolant can last for 150,000 km without loss of physical characteristics. However, it must be replaced in a number of unforeseen cases, as well as during scheduled maintenance, carried out either in a service center or in a garage. In this case, we have some tips.

Functions and features of antifreeze

All cars, without exception, including the VAZ 2110, use coolants to stabilize the engine temperature and maintain normal operating temperature. When the liquid loses its performance qualities, then it is necessary to replace the VAZ 2110 antifreeze, as all antifreezes are mistakenly called.

Antifreeze is a brand of antifreeze developed in 1971 by the All-Union Scientific Research Institute of Organic Synthesis Technologies. We inherited its name from our dark ancestors, who cooled their engines exclusively with water from wells and sipped cabbage soup with bast shoes. At that time, there was no antifreeze that would satisfy the requirements of the new VAZ 2101 engine, and the Italians, who developed and prepared it for production, flatly refused to guarantee normal operation of the engine using local antifreeze. Therefore, there was a need to develop a modern domestic coolant specifically for the new Zhiguli. So a whole generation began to call all antifreeze antifreeze. This is fundamentally wrong, and some bloopers are still speculating on this, passing off cheap dubious liquids as high-quality antifreeze.

When to change coolant

The first signs that the antifreeze needs to be changed cannot be ignored. It begins to foam, resulting in air pockets in the cooling system. This in turn leads to overheating of the engine, which does not bode well. Also, the unsuitability of antifreeze for further use can be indicated by an oil film on its surface and a characteristic rusty color. Replacing the coolant is also advisable if the engine was disassembled for a major overhaul and when there were cases of oil leakage into the water jacket.

Replacing antifreeze on a VAZ 2110

The process of replacing antifreeze is simple, you just need to do all the steps sequentially, and remember that coolant is poison. Handle it more carefully and wear gloves when replacing it. All work on replacing antifreeze is carried out only on a cold engine. The work flow is as follows:

A horizontal position of the car is desirable, but if there is a slope, it is better to place it so that the front is higher. It is better, just in case, to disconnect the negative terminal from the battery and be sure to remove the cap from the expansion tank of the cooling system.
The fluid is drained from the cylinder block quite simply on models 2110 and 2111, but on 2112 you will also have to remove the ignition module along with the bracket.
We will place a container under the engine in the area of the plug to drain the antifreeze. We unscrew the plug, drain the antifreeze, tidy up the engine compartment using a rag, since the drain hole is designed so that the antifreeze will remain not only on the cylinder block.
We move the container under the radiator and carry out the same operation with the drain hole in it. Let's be careful, because in this place the designers showed special care for the user. Old antifreeze spreads over the beam, it can soak the generator and the engine mounts will also have to be scrubbed. Antifreeze must leave the system to the last drop.
The next step is very important, because if you forget about it, air pockets may form in the system. If the engine is carburetor, then you just need to disconnect the hose from the intake manifold heating fitting. In injection models, the hose is disconnected from the throttle pipe.
Pour antifreeze into the system until its level reaches the upper edge of the expander mounting clamp and screw the plug tightly.
We connect the heating hose in place: either on the manifold or on the throttle pipe if the engine is injection.

We start the engine and warm it up to operating temperature. We turn it off, check the level, and, if necessary, top up to the required mark. We wrap the plug tightly, not forgetting that the cooling system is sealed.

Recommendations for choosing coolant

Any antifreeze is suitable for a VAZ 2110, you just need to take into account the fact that they are painted in different colors for a reason. At first, manufacturers tried to mark liquids according to the freezing temperature threshold in this way, but there weren’t enough colors for all manufacturers, so now the color of antifreeze means almost nothing, but mixing antifreeze from different companies is highly not recommended.

The VAZ 2110 system needs to be filled with 7.5-8 liters of liquid, but it is better to buy a ten-liter container at once so that there is antifreeze left for topping up. Don't overheat the engine, and good luck on the road!

Required amount of coolant for VAZ 2110

After a certain mileage and operation of the VAZ 2110 car, it is necessary to carry out a technical inspection, monitor the level of oil and coolant in the system. After a certain period of operation, all lubricants and coolants lose their original technical and operational characteristics and require replacement. Therefore, before replacing the coolant, you need to find out how much antifreeze is in the cooling system of the VAZ 2110.

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline! Read more"

Many inexperienced car enthusiasts, when replacing antifreeze or antifreeze in a car's cooling system, fill in 5-6 liters of fluid and make sure that it has reached the maximum level in the expansion tank, consider this sufficient and close the hood of the car. This is their big mistake , since the antifreeze has not yet had time to completely fill the system. You need to wait about five minutes until the liquid level in the tank drops significantly. Accordingly, you will need to add more coolant.

We recommend: How to fix a dent on a car with your own hands?

This procedure must be done several times, only then will it be clear how many liters of antifreeze are in the VAZ 2110 cooling system. It is necessary to add fluid until its level stops at one mark, which should be above the minimum and below the maximum level. Not adding enough antifreeze or antifreeze can cause the engine to overheat and fail. It is also impossible to overfill coolant, since when heated it tends to increase in volume.

After pouring antifreeze (antifreeze), you need to perform the following steps:

close the expansion tank cap;
start the engine and wait until it warms up before turning on the fan;
turn off the engine and let it cool down;
Check the coolant level in the tank and top up if necessary.

A VAZ 2110 needs to be filled with approximately 8 liters of coolant. This is a rather important procedure on which the life of the car engine depends.

How to remove an air lock from the cooling system of a VAZ 2110, 2112

1.If the car has recently been running, then you need to wait until it cools down. 2.Unscrew the cap of the expansion tank, only with the engine cooled down, otherwise antifreeze under pressure may splash out. 3. Disconnect the coolant supply hose from the throttle pipe heating fitting if you have an injector

Or disconnect the hose from the carburetor heating fitting if you have a carburetor

4. Fill the antifreeze into the expansion tank to level 5. Attach the hose back.

Many people, including experienced car owners, drive their own cars for more than 100 thousand km and never change the coolant during all this time. But in vain, because replacing the VAZ 2110 coolant is an extremely important point in the service. According to the operating rules, replacement of antifreeze or antifreeze must be carried out every two years or 45 thousand km of vehicle mileage.

If antifreeze is not replaced in a timely manner, rust may appear prematurely in the channels of the block and cylinder head. Subsequently, this may lead to a reduction in engine life. Very often, mechanics, when disassembling engines, discover rust-corroded cooling channels in the cylinder head. And it was enough just to replace the coolant in time.

When is it necessary to change the coolant on a VAZ-2110

There are no specific regulations for replacing the cooling system fluid and there are several reasons for this.

Dirty coolant in the expansion tank.

The type of coolant greatly affects its service life and this must be taken into account.

For example, inexpensive liquids based on ethylene glycol can last up to one and a half to two years .
More modern antifreezes of class G12, G12+, G13 can easily last up to 4 years.

However, the replacement period may be dictated by the condition of the fluid:

oily spots on the surface of the liquid;
complete loss of color;
foreign particles in the expansion tank;
foaming and frequent boiling of antifreeze;
loss of density due to frequent addition of distilled water.

These signs will indicate that it is time to change the antifreeze.

Inspecting the reservoir and the condition of the coolant (color, shape, dirt and foreign impurities) should become a habit!

Antifreeze selection basics

For replacement, we select, if possible, the same antifreeze that was originally poured into the engine.

Otherwise, the cooling system must be flushed , since mixing antifreeze of different brands and even different manufacturers can lead to sedimentation, clogging of the cooling system and the antifreeze losing its lubricating, cooling, flushing and antifreeze properties.

When and why do you need to change the refrigerant?

According to the recommendations of the car manufacturer, the coolant in the engine should be replaced every 75 thousand kilometers, or 3 years of operation, regardless of how long the car has been driven. In addition, the refrigerant must be replaced if the car owner detects signs that it has lost its properties, changed color or consistency.

If this is not done, the engine is at risk of overheating. Moreover, low-quality coolant provokes scale deposits in the channels of the cooling jacket, in the main and heating radiators.

Draining antifreeze from the VAZ-2110

Before draining antifreeze or antifreeze from a VAZ-2110 car, you need to find a suitable site for work. This could be a garage or other flat area. If you do not have the opportunity to carry out work indoors, then you can install the car so that its front part is slightly higher than the rear. Next follow the instructions:

Disconnect the negative terminal of the battery to de-energize the vehicle.
Remove the ignition module with bracket.
To increase the pressure in the cooling system, it is necessary to remove the expansion tank cap.
Next, install a wide, cut canister or bucket under the power plant into which you will drain the coolant that has expired.
Unscrew the antifreeze drain plug on the engine block. After this, you will only have to wait until the coolant is completely removed from the system. Wipe the plug and drain hole with a rag.
Repeat the procedure with the radiator. Place the bucket and unscrew the cap on its bottom. Wait until this unit is empty, then wipe the drain hole and plug with a clean rag.

If your VAZ-2110 has an injection engine with 16 or 8 valves, when draining the antifreeze, you must carefully remove the antifreeze supply hose from its connection with the throttle pipe heating fitting. To do this, you will need to loosen the clamp holding it.

On cars with an engine equipped with an injection system, it is necessary to remove the hose at its connection with the carburetor heating fitting. The steps described for each engine will help you get rid of air locks in the system.

Antifreeze is frozen, what should I do?

It is best to drive it into a warm box and leave the car for a day.
An option is allowed in which the engine is wrapped in a blanket and a stream of warm air is supplied to it from a heat gun, but this is a dangerous option.

If you have diluted antifreeze with water, then it should not freeze completely.

The option of replacing the concentrate in its undiluted form . But the cost will be the same, but the effect may not be achieved, you don’t know how much water there is!

Coolant selection

First, you need to figure out how much coolant is provided in the VAZ 2110. This will allow you to purchase the required amount of antifreeze and correctly carry out the replacement procedure.

New coolant

So, the expansion tank should be filled with 7.8 liters of coolant. Although in reality, when draining, you will only get about 7 liters. Part remains inside. Therefore, when filling, there is no need to fill all 7.8 liters. 7 liters is enough.

We have already understood how much coolant is provided in the VAZ 2110, and how much needs to be filled. So it's time to choose.

In order to make a smart purchase of a new antifreeze, follow a few simple rules.

Purchase a liquid with the same characteristics, color and production that was used previously. Of course, if the previous coolant worked effectively. Mixing different types of antifreeze is a common mistake that can lead to unpredictable consequences.
Take a closer look at the packaging of the liquid you purchased. Today they sell both ready-to-fill formulations and concentrates, which must be diluted before use.
Replace antifreeze only when the engine has completely cooled down.
Start the engine after replacing the coolant strictly after all connections are made and the expansion tank cap is closed.

Preparing to replace antifreeze

Before changing antifreeze, you need to drain the old one, and this is completely logical. In total, the tank contains approximately 7.8 liters of antifreeze. You can drain 7 liters without any problems. This means that for replacement you will need only 7 liters of fresh antifreeze.

Choosing antifreeze important features:

It is best to buy antifreeze from one manufacturer. If there is a strong difference in composition, the mixture in the tank may not be very good. And this can damage the health of the car.
You need to pay attention to the type of liquid. If it is a concentrate, then it will definitely need to be diluted.
It is necessary to replace the coolant after the car has completely cooled down. And it will be possible to start the car only when everything is finally connected and checked for leaks. Otherwise all the problems will come out again.

Nuances of antifreeze

There are many opinions as to whether antifreeze is actually better than antifreeze. We will not prove our position, but rather we will tell you a few facts.

Why is it better to use antifreeze when replacing coolant in a VAZ 2110? The choice is always up to the car owner, but this particular coolant has a wide range of advantages:

When heated, the degree of expansion of antifreeze is less than that of water. Therefore, the presence of even a small gap for expansion will allow it to protect the system from rupture and maintain the integrity of the pipes and caps of the expansion tank;
The boiling point is higher than that of water;
At sub-zero temperatures, the coolant does not turn into ice and acquires a gel-like structure, which does not lead to rupture of the cooling system (CO);
Does not form foam;
Does not cause corrosion. Moreover, it has the function of preventing its occurrence.

Which antifreeze to choose

It is necessary to buy antifreeze only in specialized stores, and give preference to those manufacturers whose reputation is beyond doubt. As for the choice, it is better to use the type and brand of coolant that, again, is recommended by the car manufacturer.

Let's take, for example, Russian-made antifreeze A-40M, or A-65M. Both of these fluids are ideal for any “tens” engine. The refrigerant marking letters have the following designation: A - automotive, M - modernized.

The numbers are the freezing temperature of the antifreeze. A concentrate is also available for sale. It is designated “Antifreeze AM”. All of the listed liquids, which is important, are produced in accordance with GOST 28084-89

Procedure for replacing fluid in the cooling system

Before adding any coolant, close the engine and radiator caps, and then fill the system with antifreeze. It will be required so much that the liquid level in the expansion tank reaches the point where the belt fastening passes.

Upon completion of work, tightly screw the cap of the expansion tank and return the hose leading to the heating system. Please note that high pressure occurs in this assembly. If you do not tighten the plug tightly enough, it may break off during operation. This will inevitably lead to antifreeze leakage.

Before starting the engine, perform reverse assembly - install the ignition module and return the negative terminal to the battery. After the work described in this section, you can start the engine to warm up. You shouldn’t start driving right away - let the engine run for a while, and then check the fluid level in the expansion tank. If there were air pockets in the system, the amount of antifreeze will decrease. The top edge of the fluid will not reach the location of the belt on the reservoir. In this case, let the car sit for a while and then add antifreeze.

Sometimes, by warming up the power plant, the air plugs are not pressed through. In this case, it is necessary to repeat the procedure with the hose (described in the previous section), at the same time open the cap of the expansion tank. After excess air has escaped, it is necessary to add antifreeze to the required level.

Stages of work with replacing coolant in a VAZ 2110

Before starting the main stages of work, it is necessary to prepare the work surface, tools and equipment.

During such work, the vehicle is placed on flat surfaces or at a height. The engine must be completely cool.

The replacement process will require small containers, 8, 13 and 17 wrenches, water and new antifreeze.

Replacing antifreeze with antifreeze in a VAZ consists of the following steps:

coolant drain;
flushing the system;
filling in new refrigerant.

In VAZ 2109, 2111, 2114 models, flushing the cooling system is not necessary. It is only required if the drained antifreeze was contaminated with rust or scale.

In models VAZ 2111, 2109, 2106, 2110, before replacing, it is necessary to disconnect the negative terminals of the battery so that a short circuit does not occur when draining the antifreeze.

In models 2110, 2112, 2115, after draining the fluid, the car should be started and the engine should be left running for 4-5 minutes so that all the fluid is pumped through and out of the system. Without this moment, the remaining antifreeze, which is not removed independently, will mix with the antifreeze and can lead to engine damage.

Draining antifreeze

It is best to drain the liquid at a height: the car should be placed on a lift, overpass or above a repair pit.

Before draining antifreeze on a VAZ 2110 and other models, make sure that the system has completely cooled down.

Draining is quite simple:

A container for old antifreeze with a volume of 10 liters or more is placed under the car.
The cover is removed from the expansion tank of the system and the drain plug is unscrewed from the cylinder block with a key set to “13”.
During the process, the plug can be supported so that it is not blown away by the pressure of the liquid.

When the antifreeze is drained from the VAZ block, the plug is screwed back on. The next step in draining is draining the antifreeze from the system radiator. The process is carried out in the same way as with the cylinder block. You can also tighten the cap on the radiator yourself, without any equipment or tools.

Flushing the system

Flushing, as a step when replacing antifreeze, is necessary if the car is already very old and the cooling system has never been cleaned. On the other hand, the risks increase that if you flush the system during replacement, you can clog the radiator, thermostat and heater radiator.

Washing is carried out as follows:

old antifreeze is drained;
all plugs are screwed into place;
Distilled water is poured into the tank to the maximum level;
the engine starts and warms up to operating temperature;
the working engine is left for 5-10 minutes;
the car turns off and cools down;
After cooling, the water is drained from the tanks.

If the water remains dirty when draining, the operation must be performed several times until it becomes clean.

Filling with new antifreeze

When adding new coolant, you will need about 9 liters of new coolant. Ideally, antifreeze in a VAZ 2110 should be replaced every five years, but on older models it is better to change the fluid every second year.

Filling in new antifreeze occurs step by step:

The drain plugs are screwed in;
The hose on the throttle assembly is unscrewed;
New fluid is gradually poured in;
You should stop when the antifreeze reaches the extreme level;
The hose is twisted;
The liquid is added to the maximum mark;
The tank closes and the engine with the stove starts;
The engine warms up to operating temperature and turns off;
The replacement has been made.

The procedure is standard, but not suitable for all systems. How to change antifreeze to antifreeze in a VAZ with 16 valves? The procedure is carried out differently. After the liquid is poured into the tank, air is removed through the expansion tank, then the car starts and you need to drive it for several kilometers. The system is checked again and the liquid that has escaped is added.

Why is it worth switching from antifreeze to antifreeze: pros and cons

What is better: antifreeze or antifreeze and why it is worth replacing one with the other - these are questions that many drivers of domestic cars ask.

The advantages of antifreeze in these matters are obvious:

high boiling points;
long service life;
cleans the cooling system;
produced for long mileage.

Antifreeze is a cooler that was created for the domestic auto industry, and for many years it served our cars. However, antifreeze had to be changed every 2 years, and antifreeze is designed for 5 years of operation.

In fact, antifreeze and antifreeze are the same thing. Only the latter is an improved version of the liquid. It follows from this that replacing the refrigerant in a VAZ is an important procedure that has a positive effect on the operation of the engine and other components.

When you decide to replace antifreeze with antifreeze in your car, follow the instructions, because the slightest mistake can lead to major damage to the car’s systems.

Note to car owners

Please know that if you do not replace the antifreeze in a timely manner, then premature corrosion begins in the channels of the engine block and its head and, as a result, the engine life is significantly reduced:

This affects the cylinder head the most.
Working as a car mechanic, I often had to disassemble engines and observe the head cooling channels eaten away by corrosion
After such a spectacle, anyone will feel scared for their car; you will certainly forget to change the antifreeze in a timely manner.
At each scheduled maintenance, you need to check the level and appearance of antifreeze (more often if possible)

Important: The antifreeze level must be checked on a cooled engine; the permissible level is within (between) the lower and upper marks on the body of your expansion tank. A slight increase or decrease in this level that occurs when it is cooled or heated is not considered a malfunction; this is absolutely normal. Such level fluctuations are associated with thermal changes in volume (for example, expansion when heated and subsequent decrease in volume when cooled). However, if you notice a gradual decrease in the level with each new check on a cold engine, then you need to look for where the leak is occurring.

Optimal coolant option

When we figured out how to replace antifreeze on a VAZ 2110 (2112),

It is important to choose the optimal liquid option . Many car enthusiasts only use expensive antifreeze, considering it to be of higher quality. For VAZ cars, it is quite possible to use a cheap domestic product - antifreeze, the characteristics of which were developed specifically for these cars.

Owners of domestic cars respond positively to Felix brand antifreeze. It is sold in canisters of 5 and 10 liters, and smaller containers. It is profitable to purchase liquid in a 10 kg container - it is cheaper, and after replacing the used antifreeze, there is still liquid left for refilling.

We drain the antifreeze ourselves

To drain antifreeze and fill in new fluid, we need a drain container with a volume of at least 7.5-8 liters.

You will also need keys and flushing fluid if the system needs to be cleaned.

To refill the system, 7–7.5 liters of finished liquid . This must be taken into account if we pour the concentrate and dilute it with distilled water. It is advisable to carry out the work with gloves, since antifreeze is toxic. Before replacement, we will conduct a detailed inspection of the system, eliminate fluid leaks, and replace failed pipes and clamps.

Algorithm

We carry out replacements on a cold engine according to the following algorithm:

We place the car on a level surface; if possible, we place the car so that its front part is slightly higher than the rear.
Remove the negative terminal from the battery.
We install the heater valve in the extreme right, hottest position.
Turn the heater control knob to the right until it stops.
Remove the engine protection, if installed.
Unscrew the screws securing the engine protection.
Disconnect the wires from the ignition module and remove it to provide access to the drain plug on the cylinder block.
Disconnect the connector.
Unscrew the fastening bolts.
Read also: Lada Kalina Universal Logbook Replacement of ball joints
We take out the ignition module.
Remove the plug from the expansion tank.
We place a container under the radiator drain plug, unscrew it and wait until all the liquid flows out.
Unscrew the plug at the bottom of the radiator.
Place a container under the cylinder block plug. We are waiting for the old fluid to be completely removed.
Using a 13 key, unscrew the plug on the front side of the cylinder block.
After draining the antifreeze, wipe the cylinder block and radiator with a rag, replace the block plug and tighten the plug on the radiator.
Remove the throttle body heating hose. This will avoid the formation of an air lock in the system.
Disconnect the fluid supply hose to the throttle body.
Fill the expansion tank with new antifreeze to the maximum level and screw on the cap.
Fill with antifreeze to the required level.
We put the hose in place on the throttle assembly.
We put the ignition module in place and screw the negative terminal to the battery.
We start the engine; as it warms up, the fluid level may drop. In this case, we will add fresh antifreeze to the required level.
Warm up the engine to operating temperature.
We check the system for leaks.
Check the coolant level in the expansion tank.

Operating procedure

Draining old coolant

If the replacement is made on a lift or inspection pit, it is necessary to remove the engine protection, if any. When replacing without a pit, you don’t have to remove the protection, but then old antifreeze will get on the protection. There is nothing dangerous about this, but for a few days after the replacement, you may smell antifreeze until it evaporates. We place a drain container under the lower right side of the radiator, if conditions permit.

If you are not changing it in an equipped place and you do not need the old antifreeze, you can simply dump it on the ground. Many people advise initially opening the cap of the expansion tank, then unscrewing the plug at the bottom of the radiator to drain, but in this case old antifreeze under high pressure, especially if the engine has not completely cooled down, will flow out of the radiator. It is safer and more convenient to first unscrew the cap (plastic wing) of the radiator, the old antifreeze will flow in a thin stream, then carefully unscrew the cap of the expansion tank, thereby, due to the tightness in the cooling system, you will be able to regulate the antifreeze drain pressure.

After draining the antifreeze from the radiator, we need to drain the liquid from the engine cylinder block. The peculiarity of draining antifreeze on a VAZ 2110 from the cylinder block is that the plug on the block is closed by the ignition coil (on a 16-valve injection engine). To do this, we need to dismantle it, use a 17mm wrench to unscrew the bottom bolt of the coil bracket, use a 13mm wrench to unscrew the side and central bolts securing the bracket and move the coil to the side. Using a 13 key, unscrew the drain plug from the cylinder block. To more completely remove old antifreeze, you can connect an air compressor and apply air pressure through the filler neck of the expansion tank.

We tighten the plug of the cylinder block and the plug on the radiator (the plug on the radiator is plastic with a rubber gasket, it can be tightened by hand without unnecessary force; for reliability, you can coat the threads of the plug with sealant). We put back the ignition coil.

Filling with new coolant

Before adding new antifreeze to the VAZ 2110, it is necessary to disconnect the heating hose to the throttle valve (for an injection engine), or the hose from the carburetor heating fitting (on a carburetor engine), so that excess air can escape from the cooling system. Fill in new antifreeze to the level of the upper part of the fastening of the rubber belt of the expansion tank. We connect the hoses to the throttle valve or carburetor, depending on the model. Close the expansion tank cap tightly. Open the heater tap in the cabin to the hot position.

Filling antifreeze into a VAZ 2110

We start the engine. Immediately after starting the engine on a VAZ 2110, you need to pay attention to the level of antifreeze in the expansion tank; it may immediately drop, this may mean that the water pump has pumped coolant into the system. We turn off the engine, top up the level and start again. We warm up the car. During warm-up, we check for leaks in the engine compartment, in places where hoses and plugs were removed. We monitor the engine temperature.

When the operating temperature reaches 90 degrees, turn on the heater; if it heats with warm air, turn it off and wait for the engine cooling fan to turn on. When you turn on the fan, wait for it to turn off, turn off the engine, wait 10 minutes for the engine to cool down a little, unscrew the cap of the expansion tank, check the coolant level, and add if necessary.

General cooling system maintenance tips

First of all, you need to adhere to the following safety tips:

Cool the car completely; its engine should be completely cold.
Remember that antifreeze is a fairly toxic liquid, so you should not allow it to get into the stomach, skin or eyes. Wear gloves when working.
After you fill in new antifreeze, you can start the car only after installing the expansion tank cap in place.

If you have replaced the heater core, you need to check the operation of the fan. To do this, monitor the coolant temperature on the dashboard. If the arrow reaches the red zone and the fan still does not turn on, you need to turn on the airflow from the heater. Cold air indicates an air lock, and hot air indicates a fan malfunction.

You can remove the plug from the air when the power unit is turned off and cooled; to do this, you just need to unscrew the cap of the expansion tank.

Reasons for replacement

When replacing antifreeze on a VAZ 2110, you must adhere to several rules. The engine must be cold, antifreeze is a toxic liquid; when working with it, it is necessary to avoid contact with the eyes, mouth and prolonged contact with the skin.

Antifreeze, coolant (antifreeze) is a special composition of automotive fluid based on ethylene glycol. Used in the cooling system of an internal combustion engine (ICE) for operation at low ambient temperatures. There may be several reasons for replacing antifreeze:

car mileage, 75,000 – 100,000 km. mileage;
time interval 3 – 5 years (it is recommended to check the condition of the fluid at a car service every year before the start of the winter season with a special device);
replacing one of the components of the cooling system, water pump, pipes, radiator, heater, etc., with such replacements, antifreeze is still drained from the cooling system and it makes sense to fill in a new one.

When to change coolant

Not all motorists know what the life cycle of antifreeze is. It is approximately 150 thousand kilometers. In theory, maybe more, but it’s better not to risk it and, for the sake of prevention, change it even more often.

Drain plug

There are several situations that will require you to carry out a mandatory coolant replacement procedure.

The color of the coolant has changed. The liquid may take on a rusty color. This indicates the need for replacement.
An oil film has formed on the surface of the cooler.
Antifreeze often bubbles in the expansion tank of a VAZ 2110. Moreover, there were no prerequisites for such a phenomenon. The Ten is a car for good speeds, because when driving at low speeds, the antifreeze in the expansion tank on the VAZ 2110 often boils. This is because the cooling fan does not turn on.
A coolant that is no longer suitable for further use may also boil, the composition of which has changed significantly since it was poured into the expansion tank.
Antifreeze is leaking somewhere from the expansion tank on a VAZ 2110. The situation is common, but it cannot be solved by adding or replacing coolant. It is necessary to find where the antifreeze is leaking from the expansion tank of the VAZ 2110. Usually the leak is found on the clamps, although it would not be a bad idea to check the entire system.
The coolant level may be normal, during operation it does not emit antifreeze from the expansion tank of the VAZ 2110, the color is normal, but still the boiling process occurs quickly. Most likely, the reason lies in the airlock.

How to change coolant

Before replacing antifreeze, you need to know that this can only be done on a cooled engine. Antifreeze and antifreeze are aggressive chemicals that can cause harm to the human body, therefore, follow safety precautions and carry out all work with gloves. You can start the car after changing the fluid only after you make sure that the reservoir cap is tightly screwed on.

Drain the coolant

Many drivers are interested in how to drain antifreeze from a VAZ 2110 and do it quickly and correctly.

Before you start changing the antifreeze, you need to place the machine on a horizontal platform. And if this is not possible, then make sure that the back is slightly lower than the front.

Disconnect the negative terminal from the battery.
Together with the bracket, remove the ignition module.
Ignition module
We unscrew the cap of the expansion tank, having previously installed a 10 liter capacity to drain the used coolant.
Draining old fluid
Drain the cooler.
We wipe the cylinder block from any remaining fluid.
We tighten the plugs of the radiator and cylinder block.

Filling with coolant

Before disconnecting the coolant supply hose, loosen the clamp.
If the engine is equipped with a carburetor, then you need to disconnect the hose from the fitting so that air can escape during filling.
We begin to pour antifreeze into the system (about 7-8 liters will be needed) until its volume reaches the level of the upper line of the expansion tank fastening belt.
We pour new antifreeze through the funnel
Be sure to tighten the plug tightly, otherwise if the coolant boils, it may splash out.
We connect the hose.
We put the ignition system in place.
Connect the “-” terminal to the battery.
We start the engine and wait for it to warm up to operating temperature.
Liquid level in the tank
We look at the position of the sensor pointer and the level in the tank;
After a few days, it is advisable to check and determine whether the coolant level in the expansion tank is normal.

Is there a difference in the processes of draining antifreeze in eight- and sixteen-valve engines?

There is a difference, and it is significant. The fact is that the “tens” engines have different designs. In terms of draining antifreeze, a VAZ-2110 with 8 valves is more profitable than a dozen with sixteen valves. The first has a coolant drain plug located on the front of the cylinder block. To get to it, you don’t need to drive the car into the inspection hole or remove the protection. But for sixteen-valve power units, the plug is located at the bottom, and can even be closed by the starter, so before draining the antifreeze from the VAZ-2110, you will need to drive the car into a pit (overpass), remove both the protection and the starter. Let us consider this process in more detail for each of the engines.

Replacement features

If there are small leaks in the engine cooling system and the car owner periodically adds water or antifreeze from different manufacturers, the old coolant may take on a rusty color. Foreign bodies may appear in the form of small chips and rust, which, by the way, can lead to failure of the main elements of the cooling system, water pump, thermostat, heater tap, etc.

Flushing the VAZ 2110 cooling system

In this regard, when replacing old antifreeze in this condition, it is necessary to flush the system. This can be done using different additives, which is not always beneficial for the cooling system. Low-quality cleaning additives may not only not help, but also damage the components of the cooling system. Therefore, it is necessary to use high-quality additives and not skimp.

You can also flush the system naturally with distilled water. After draining the old antifreeze, water is added. The car idles for 10-15 minutes, then it is drained again and new antifreeze is added. If there is severe rust, you can repeat the procedure.

There is a cheaper and easier way; you can simply flush the system with plain water by opening the radiator and engine caps in sequence. Those. the engine cap is unscrewed and water is spilled through the expansion tank. Then the engine plug is closed and the radiator drain plug is opened. Do only in this sequence, since the radiator is at the lowest point and all the water will pour out.

Antifreeze and antifreeze: differences

Coolants from different manufacturers differ in their production and manufacturing processes, as well as in the additive packages they contain.

The recommendations specified in the operating manual or service book (name, manufacturer, fluid class, etc.) will help you choose the right fluid.

Depending on the production technology, there are three types of coolant:

traditional production technology (the liquid contains additives based on salts of inorganic acids);
carboxylate production technology (the liquid contains additives based on organic salts);
hybrid production technology (creation of additives based on carbon salts with a low content of phosphates and silicates).

Antifreeze is produced using traditional technology, and antifreeze is produced using carboxylate technology. Both antifreeze and antifreeze have a number of positive properties (increased efficiency of the internal combustion engine cooling system, anti-corrosion properties, etc.).

For this reason, the choice of fluid can be made by the car owner himself. Moreover, in practice, the VAZ 2110 is not an expensive car that requires the latest generation of antifreeze to be poured into it. Moreover, antifreeze is poured into the engine at the factory.

Often, in the future, owners continue to fill with more affordable domestic antifreeze, rather than antifreeze. However, it also happens that owners deliberately switch from antifreeze to antifreeze. It is important to remember that you cannot mix antifreeze and antifreeze, so before such transitions from one type to another, the cooling system must be thoroughly flushed.