Interpretation of error p1602 - controller voltage interruption

Error p1602 stands for “Control system controller, board voltage interruption.” In practice, this means that somewhere in the car’s electrical network a contact has disappeared, most likely a “minus” one. Most often, error p1602 occurs on domestic VAZ cars, starting from the tenth model (VAZ-2110) and higher - on Kalina, Priora. The difficulty of diagnosis lies in the fact that the electronic scanner is not able to show in which particular area or specific device the on-board voltage has disappeared. Therefore, localizing the location of a breakdown sometimes takes a lot of time and effort.

What does the error code mean?

Error P1602 is diagnosed on cars when one of the on-board voltages is not supplied to the engine control unit (ECU). Various options are possible: both permanent absence and short-term outages (one-time or periodic).

As a rule, the control unit receives voltage via several buses:

• 30 bus – on-board network voltage, which operates constantly, parallel to the positive terminal of the battery;
• 15 bus – on-board network voltage through the ignition switch (relay);
• 50 bus – on-board network voltage supplied when the “engine START” key is turned on.

In this case, the engine control unit can receive direct power from various contacts of the ECU connector. Thus, monitoring the voltages supplied to the engine control unit is difficult in the absence of a circuit diagram. Depending on which power supply is missing, the vehicle may behave differently with the same P1602 error.

The most characteristic symptoms:

• the ignition does not turn on;
• the ignition turns on, the starter does not start;
• the ignition turns on, the starter operates when the engine starts, the engine does not start;
• the ignition turns on, the engine starts, does not respond to the accelerator pedal or other controls;
• the ignition is turned on, the engine starts, there is color music on the dashboard (indicator lights blink, dial gauges deviate chaotically);
• The car is operating normally, the error is diagnosed.

Error P1602 does not necessarily indicate a complete lack of voltage at one of the power inputs. The battery may have been discharged to a critical level or was temporarily disconnected from the terminals. After connecting the battery, error P1602 remains in the memory of the control unit, and it is enough to delete it (erase from memory) for the engine ECU to exit the emergency mode.

Decoding P1602

• Low voltage supply to the engine control unit (AUDI, ISUZU, SAAB, VOLKSWAGEN).
• Knock Sensor Module Performance (BUICK, CADILLAC, CHEVROLET, GMC).
• Speed ​​Control Solenoid (DODGE) Circuit.
• Problem with the wiring of the engine control unit (HYUNDAI, KIA).
• Engine control unit immobilizer error (MAZDA).

Where is the P1602 sensor located?

The image above shows the ECU connector of an Audi Q7, terminal 30 is circled.

It should be noted that this code does not refer to the voltage at terminal #30 as shown here, but to the various and multiple terminals in the connector that should have a certain voltage across them when the ignition is turned off. Therefore, the presence or absence of power at terminal No. 30 (as shown here) when the ignition is turned OFF should NOT be taken as evidence of failure or malfunction unless the manual for the vehicle in question explicitly states that the specified voltage should or should not (depending on depending on the circumstances) be present at this terminal when the ignition is turned off.

Operating principles of the on-board computer

The electronic control unit of the VAZ 2114, as on other cars, is primarily designed to monitor the condition of various components and assemblies, as well as for subsequent indication of breakdowns if they occur. The introduction of the concept of self-diagnosis is a sound decision designed to facilitate both the operation of the car for the driver and possible repairs for the car service center.

The system works simply: if a unit breaks down or there is no signal from it, the ECU displays a coded message on a small display, which can be deciphered using the appropriate car manual.

Alas, as often happens with the domestic auto industry, the electronic brains of the ECU may begin to fail for one reason or another, giving the VAZ 2114 error 1602 in situations where there is no real breakdown. At the same time, the problem cannot be ignored under any circumstances, because once out of ten the control unit can signal that there are actually problems in the system.

Instead of immediately going to a service center and paying money for diagnostics, experts recommend trying to find out the cause of error 1602 on your own - it is quite possible that even an inexperienced car owner will be able to solve the problem.

It is important to remember that first of all, you should exclude the possibility of an error in the operation of the ECU itself and sensors if any error is detected on the screen. It will be useful to buy only original electronics parts in advance when operating a car, and not install cheap analogues (the same is true for unlicensed firmware).

This is interesting: What should you do if the oil pressure light comes on at idle?

As for the general list of reasons that can alert the ECU with a problem message, the most common factors are:

1. Changing the type of fuel system without flashing the controller.
2. Low quality fuel, which has a complex effect on the entire energy system.
3. Clogged air or fuel filter.
4. Inept attempts to reconfigure the “brains” of the controller.
5. System failure of the ECU or failure of one of the sensors.

Do not forget that any intervention in the factory settings of the computer or replacement of sensors (as well as cables and connectors) with unofficial ones, not produced by AvtoVAZ, is fraught with frequent errors in the operation of the ECU - as a result, this means lost nerves and money in the future.

Lada Vesta ECU and suitable scanners

Vesta electronic control received a CAN interface. Brains communicate with various systems through digitally encoded signals. Moreover, the Itelm M86 ECU is easily coordinated with third-party security devices (alarms), GPS trackers, and multimedia systems. The only requirement is the presence of an appropriate data bus.

For diagnostics, reading indicators and errors, ELM327 automotive scanners are used. They also use other multi-brand devices that operate using the OBD2 protocol and CAN bus:

Diagnostic capabilities of LADA VESTA systems:

ECU location:

On this vehicle, the ECU is located in the engine compartment, on the right side (view from the front). Fixed with several screws to the shock absorber shell. The wire connection blocks are located at the bottom of the block, but the ECU itself is rotated 90 degrees. The tires are secured with latches. To remove the chip, unlatch the lock and remove the block.

By the way, removing the ECU is only necessary when flashing the controller firmware.

Chip tuning and firmware of Vesta ECU:

The original firmware is tailored to harmonize engine emissions with EURO standards. Chip units have modified software that disables some sensors (lambda) for high dynamic performance. You can find out the firmware type through OpenDiag. How to flash the ECU will be discussed below.

Possible reasons

When diagnosing error P1602, the engine control unit is insufficiently powered from the on-board network. What could be the reasons:

• temporary disconnection of the battery terminals (terminals) from the on-board network for the period of repair or maintenance;
• critically low battery charge;
• voltage dips in the on-board network during engine startup with low residual battery capacity (for example, during engine startup at extremely low ambient temperatures);
• fuse blown in the power supply circuit;
• fraying of contacts or malfunction of relays servicing the engine control unit;
• contact failure of the control unit connector;
• abnormal operation of car alarms;
• error on the CAN bus (communication bus between control systems);
• problems with the generator;
• violation of the common wire (ground) of the car;
• control unit malfunction;
• previous polarity reversal when installing the battery.

Symptoms

Error P1602 on the VAZ 2114 is notable for the fact that sometimes it can appear asymptomatically. The owner learns about it only from the readings of the on-board computer or when conducting diagnostics with a scanner. Therefore, it can be difficult to determine. Additionally, the occurrence of this code may be intermittent.

In some cases, when the ECU reports this code, problems with starting the engine may occur. It may start poorly, not the first time, or not start at all. But this is also not a characteristic feature of this problem. In a similar way, a machine can report many faults.

Error 1602 on VAZ cars: what is the reason

If you look through the VAZ manuals that came with the car, you will find information in them that this malfunction can only occur under the following conditions:

• With the ignition off;
• If the controller notices that some data has been lost.

This problem occurs on almost all relatively new VAZ models, for example:

• Priora;
• Grant;
• VAZ 2110;
• VAZ 2112;
• VAZ 2114;
• Kalina;
• Niva Chevrolet;

It’s difficult for me to immediately see all the reasons for error P1602. I will try to talk about the main ones. I will describe the problem using the example of individual units in which an error can most often occur:

1. Battery. It may be discharged or you have poor terminal contact. I once had a problem due to a large number of electrical appliances (I connected an electric winch and plugged in a few more lamps). The system couldn't cope. Also, P1602 may appear if you change the battery or when starting the engine on a discharged battery.
2. Generator. The reason may be its power or the fact that the contact disappears. The problem often occurs on Priors, Kalinas and VAZ 2114

1. Signaling. There are modern car protection systems that turn off the battery when the alarm is turned on. It is assumed that if thieves get into the cabin, they will not start the engine. However, the system may generate this exact error.
2. Minor power loss. For example, you start your car in cold weather. A large flow of energy went from the battery to the starter. The controller was left without power for a short time. As a result, the system issued P1602.
3. “Mass” of the controller. The reason is quite common. Your car contact is simply oxidized, and the system thinks that it has been left without power and generates an error.
4. "Mass" between the body and the engine. This happens if your engine is damaged (for example, after an accident), contacts are oxidized, or wire insulation is damaged.
5. Safety block. The wires in them can also periodically oxidize. As a result, the voltage may also drop. Although the block itself is also worth checking, the reason may be in itself.
6. Control electrical unit. The error may also appear due to hardware problems. Then I recommend that you contact the service; if you don’t understand it, then it’s better not to get into the firmware yourself.

This is interesting: What are gasoline additives, pros and cons, and what are they needed for?

How to check the generator and replace the brushes on it

If you have tried all possible troubleshooting options on your VAZ-2114, but nothing worked, check the generator. To do this you will have to dismantle it:

1. Remove the negative terminal from the battery and disconnect the wire leading to the generator casing.
2. Remove the nuts from the upper and lower alternator mountings, then loosen the tension bolt and remove the alternator belt.
3. Remove the clamping bar.
4. Remove the generator along with the casing.

There are several ways to check the generator. One of them is to use a stand, but it is only available in car services. Ordinary car enthusiasts will have to disassemble the generator, check its coil with a multimeter and inspect the components. Particular attention should be paid to the brushes, which need to be replaced if necessary. Often a coil or bearing wears out its life, in which case you will need to purchase these components and install them in place of the failed ones.

Source

Elimination methods

Methods for eliminating error p1602 directly depend on the reason why it was formed in the memory of the electronic control unit. However, before performing the steps listed below, it makes sense to programmatically reset the error. If there are no visible breakdowns, then it is quite possible that the error “Court Controller, loss of supply voltage” was generated accidentally.

We list possible solutions to the problem in the same sequence as the reasons that caused them:

• Battery. Use a normally charged battery that holds a charge well and also has the appropriate capacity suitable for a particular vehicle (this is especially true for winter, when difficult engine starts are expected). Periodically check the charge level, electrolyte density, the quality of the terminal contacts on the battery, and if necessary, clean and lubricate them. Clean the contacts on the wires in the same way. If possible, you can check the battery leakage current. Sometimes an action that helps get rid of the error is to remove the negative wire from the battery for about 5 minutes (a few seconds are not enough!!!), and then quickly put it on and set it in such a way as to ensure tight contact between the wire and the terminal battery It is also advisable to first clean and lubricate the contact.
• Generator. It makes sense to double-check the operation of the diode bridge, check the voltage at the terminals (on most modern passenger cars the corresponding value should be about 13.7...14.0 V). Check the ground of the generator and, if necessary, inspect the wire and corresponding contacts. Similarly, clean all accessible contacts on the generator, as well as tighten them. You can also re-stripe the wires and make new contacts to improve their quality. Clean the base of the generator mount and the engine block at the point of contact. In some cases, tightening the alternator belt helps (especially if it slips and whistles); if the belt is significantly worn, it is better to replace it with a new one. In rare cases, the generator is completely replaced.
• Signaling. Regarding the alarm system, it is advisable to consult with the employees who installed the alarm system on the car, or find documentation for it on the Internet and find out whether it disconnects the battery from the system as protection or not. If yes, then you will have to come to terms with this error, or, as a last resort, change the alarm system to another one without a similar function.
• Short-term voltage drop. Usually in this case, this error is simply reset programmatically from the ECU memory. It should not be restored in the future.
• "Mass" of the ECU. Check the quality of the ground; if it is damaged, restore the integrity of the contact and/or wire. The chip may be damaged.
• Ground connection between the body and the engine. Inspect the wires and contact connections; the tips (if any) may be damaged. If necessary, test the wire with a multimeter to check for continuity or damage to the insulation. If the wire is broken or damaged, it must be replaced with a new one. In this case, it is advisable to use tips.
• Fuse box. Check the contacts in the block. Moreover, both coming from the battery and internal ones, directly on the fuses themselves. If necessary, tighten the contacts, remove oxides, and lubricate. It is especially necessary to check the fuse that goes to the electronic control unit, as well as its seat, the quality and cleanliness of the contact, and if necessary, inspect and clean it. It is also advisable to check the condition of the contacts in a special block under the hood. To do this, it is better to use a special contact cleaner.
• Electronic control unit. If there is such a possibility, it is advisable to install an ECU of the same model with the same firmware version on the car. At the same time, check whether voltage is coming to the supply terminal of the control unit and what its value is. However, it is best to seek help from official dealers or a car service that repairs electronic “brains,” since reflashing or changing settings yourself can be fraught with big problems.

This is interesting: Power steering hums when cold or constantly: causes and repair of power steering

As practice shows, error 1602 itself is in most cases harmless, and the car owner finds out about it only when he uses a scanner to remove information from the ECU along with other errors or there is an on-board computer with a screen on which the relevant information is displayed. Therefore, if it does not affect the behavior of the machine (and in most cases this is the case), then the machine can be used and “bothered” about it. As for elimination, the cause is usually poor ground or battery contact.

How to fix the problem?

To fix error P1602, you need to determine the cause of its occurrence. Even during normal operation of the car, simply deleting it from the memory of the electronic control unit, as many VAZ owners do, is wrong. The problem may be more serious than it seems. The only exception is that the code appears after removing the terminal from the battery or in frosty weather.

The first step when an error is detected is to check the battery charge, the condition of its terminals and wires. It is also necessary to test with a multimeter and visually inspect the contacts on the ECU, generator and sensors, ring and evaluate the condition of the wiring by eye. It is often very easy to find the location of broken or oxidized terminals. You can fix these problems yourself.

If the generator or battery is not working properly, it is often possible to restore its functionality. The battery often just needs to be charged with a charger and the terminals cleaned. But many owners also repair the generator themselves. Sometimes it is better to replace these devices.

Problems associated with low-quality fuel are easily solved. To do this, just change the gas station. If there was a switch to another fuel or the unit was flashed, it is advisable to contact an auto electrician. He will do the correct firmware for the equipment.

Other automaker definitions for P1602

• Engine Control Module (ECM) Anti-lock Braking System (ABS) / Traction Control System (TCS), CAN Data Bus - Communication Failure (GM).
• Battery Voltage Monitor - Malfunction (Toyota).
• Engine Control Module (ECM) - Low Battery Voltage (Volkswagen).
• Engine control module (ECM) - low battery voltage (Audi).
• CAN Data Bus - Anti-lock Braking System (ABS) / Traction Control System (TCS) (Buick).
• CAN Data Bus - Anti-lock Braking System (ABS) / Traction Control System (TCS) (Cadillac).
• CAN Data Bus - Anti-lock Brake System (ASS) / Traction Control System (TCS) (Chevrolet).
• Engine Control Module (ECM) Unprogrammed (Chrysler).
• Engine Control Module (ECM) Unprogrammed (Dodge).
• Transmission Control Module (TCM) - Serial Communication Problem (Hyundai).
• ECM communication with ABS - circuit malfunction (Isuzu).
• Engine Control Module (ECM) Unprogrammed (Jeep).
• Transmission Control Module (TCM) - Communication Lost (Kia).
• Battery voltage monitoring - malfunction (Lexus).
• Immobilizer control module/engine control module (ECM) - communication error (Mazda).
• ECM for LSI system - communication failure (Mitsubishi).
• CAN Data Bus - Anti-lock Brake System (ABS)/Traction Control System (TCS) (Oldsmobile).
• Engine Control Module (ECM) Unprogrammed (Plymouth).
• CAN data bus. Engine Control Module (ECM) Anti-Lock Braking System (ABS)/Traction Control System (TCS) - Signal Malfunction (Pontiac).
• Engine control module (ECM) - faulty (Saab).
• CAN Data Bus, Anti-Lock Brake System (ASS), Traction Control System (TCS) to Engine Control Module (ECM) - Lost Communication (Saturn).
• Engine Control Module (ECM) - Programming Error (Subaru).
• Electronic Throttle System (ETS), Throttle Return Spring - Malfunction (Volvo).

Sources

• https://voditeliauto.ru/poleznaya-informaciya/to-i-remont/kod-oshibki-p1602.html
• https://elm3.ru/diagnostika/oshibka-p1602
• https://remontvazov.com/oshibka-1602-na-vaz-2114
• https://kody-oshibok.ru/avtomobili/vaz/oshibka-1602-na-avtomobilyakh-vaz.html
• https://etlib.ru/blog/1166-oshibka-r1602

[collapse]

Messages 4

• max-xx
• Moderator
• Inactive

• From: Moscow
• Posts: 2,877
• Thank you: 373

Topic: Errors P0363 and P130_(1-4) or how the ignition module dies

So a problem occurred - the car began to shake while idling in a traffic jam. Then the meat grinder flashed and the on-board alarm beeped with an error. The car began to shake more noticeably. The engine was troublesome. Then he started doubling. 3 errors popped up. P0363, P1301, P1304. P0363 – misfires detected, fuel supply to idle cylinders is turned off. P130_(1 to 4) – Cylinder (1-4), misfires detected, critical for the converter. After turning it off and on, cylinder 4 started up, only 1 remained. So I spent 1.5 hours in traffic jams. Sometimes even 4 would turn off. The restart gave it life again. If one error from 130_ popped up, then you could rack your brains and you wouldn’t immediately think about the module (spark plug, explosive wire, injector). And so if a pair of 1 and 4 or 2 and 3 is 99% dead, the ignition module is a characteristic sign, so to speak. Why is this topic raised? My mileage is 42 thousand. A friend of mine on Kalina 2 also had a 40 thousand coil. I know that many have gone through more without problems. Because there is no time to run around under warranty and ride on 3 cylinders first to work, and then under warranty, or use free evacuation - I bought a BOSCH F000ZS0211 for 1800 rubles at a good stall I know. They still had them at the old prices. Now under 3000r. they ask. You could have ours for 900 rubles. but there is no confidence that it will work adequately. Therefore, it is 2 times more expensive, BOSCH. Our module is marked 21110-3705010-03 or 2111-3705010-03.

Loss of voltage in the power supply circuit of the VAZ 2114 controller

Error P1602 on the on-board computers of VAZ 2114, 2110, Kalina vehicles means “On-board network voltage interruption” . Specifically, the on-board computer recorded a temporary, short-term lack of voltage. The problem can lead to battery drain, voltage drop and other problems. One of the most annoying problems is that the car won’t start at all. Let's figure out the reasons for this error.

Most often, the error is associated with poor contact of the wires to ground, from the generator or on the battery terminals. In simple terms: there is contact, but there is no contact. Therefore, to correct error 1602 on domestic cars Niva, Priora, Grant , etc. contacts need to be cleaned .

The main contact from the generator, which should be thoroughly cleaned. It is located below all other contacts and most often loses contact.

Check the contacts on the battery terminals and, if necessary, clean them of oxides.

If you solved the problem in another way, share it with us in the comments.

Welcome to ChipTuner Forum.

Theme Options

marat2008

What are you looking at, a scanner? The scanner may not detect a short-term voltage drop when the starter is turned on. I would like to record it with an oscilloscope on a recorder. Or throw in a battery that is known to be good. It would be a good idea to check the spark plugs for the presence of a resistor and the explosive wires for resistance. Also clean all the masses.

Added after 3 minutes

Johnvaldai

I changed the battery, first of all I passed every single one of the masses. The car started up, ran for half an hour and died with the same error. Apparently the heat increases the resistance somewhere. I'm looking further. Tell me what else I can look at. For now I'm digging through all the harnesses with my hands.

Added after 2 minutes

What are you looking at, a scanner? The scanner may not detect a short-term voltage drop when the starter is turned on. I would like to record it with an oscilloscope on a recorder. Or throw in a battery that is known to be good. It would be a good idea to check the spark plugs for the presence of a resistor and the explosive wires for resistance. Also clean all the masses.

Added after 3 minutes

I don't know this code.

Scanmateg issues, it is called Immobilizer is not disarmed with its key.

Added after 3 minutes

[quote=Johnvaldai;407785]What are you watching with, a scanner?

I check the voltage with a voltmeter directly from pin 18 of the ECU. Drop to 9.0 V

Error 1602 appears (loss of mains voltage in the controller), while the car is working normally, I cleared the error by removing the terminal from the battery, the error is erased but appears again after a while.

Loss of voltage in the power supply circuit of the VAZ 2114 controller

I (21103) also got error 1602 after charging the battery. Everything works except the fuel pump, it is silent. But even if the pump died, why is there such an error?

Check relays and fuses.

The fuses have been checked, even the relays have been swapped (they are identical side by side). The relay clicks when the ignition is turned on, but the pump is silent. It looks like the pump died (standing in the garage?). But why does the computer display error 1602? Is this somehow related?

I don’t remember exactly now, but it seems the fuel pump fuse is next to the fuse. ECU, i.e. behind the right cover of the “beard”, and not in the CN. There's a blue block down there. Have they been checked too?

I don’t remember exactly now, but it seems the fuel pump fuse is next to the fuse. ECU, i.e. behind the right cover of the “beard”, and not in the CN. There's a blue block down there. Have they been checked too?[/quote]

Yes, I checked - they are there together (fuse and fuel pump relay).

Yes, and also, I don’t understand, the car won’t start? If it doesn’t start, after turning on the starter, in theory (although not always) more errors should pop up. Have you looked at them all? And the terminal, as I wrote, was reset?

The car won't start. The pump does not buzz. The computer shows error 1602. The terminal was reset several times, including for a long period of time. There is no pressure in the rail (checked through the valve). There are 4 wires on the fuel pump block (I didn’t find a description of this block on the electrical diagrams): red, brown (or dirty gray), black and white, blue and red (in order from left to right). When the ignition is turned on, about 12 volts appear between red and black and white. All the signs seem to be that the pump itself died (suddenly). BUT WHY (even if he died) DOES THE COMPUTER GIVE ERROR 1602? I don't understand.

I don’t remember exactly now, but it seems like the fuse The car won’t start. The pump does not buzz. The computer shows error 1602. The terminal was reset several times, including for a long period of time. There is no pressure in the rail (checked through the valve). There are 4 wires on the fuel pump block (I didn’t find a description of this block on the electrical diagrams): red, brown (or dirty gray), black and white, blue and red (in order from left to right). When the ignition is turned on, about 12 volts appear between red and black and white. All the signs seem to be that the pump itself died (suddenly). BUT WHY (even if he died) DOES THE COMPUTER GIVE ERROR 1602? I don't understand.

The fact is that error 1602 is called “Loss of mains voltage” and appears when the battery terminal is removed (or when the controller is removed). Those. It is impossible to reset it by removing the battery terminal! It has nothing to do with a non-working fuel pump. Question for clarification: Does the fuel pump relay activate when the ignition is turned on? or cranking the engine with the starter?

The fact is that error 1602 is called “Loss of mains voltage” and appears when the battery terminal is removed (or when the controller is removed). Those. It is impossible to reset it by removing the battery terminal! It has nothing to do with a non-working fuel pump. Question for clarification: Does the fuel pump relay activate when the ignition is turned on? or cranking the engine with the starter?

The fuel pump relay is activated, i.e. clicks when the ignition is turned on. When the starter is turned on, whether it fires or not, I don’t know, I haven’t checked. To eliminate any malfunctions with this relay, I replaced it with a similar one (the main relay is the ignition relay). The result has not changed.

The fact is that error 1602 is called “Loss of mains voltage” and appears when the battery terminal is removed (or when the controller is removed). Those. It is impossible to reset it by removing the battery terminal! It has nothing to do with a non-working fuel pump. Question for clarification: Does the fuel pump relay activate when the ignition is turned on? or cranking the engine with the starter?

No, what the error is called and why it appears is clear to everyone (it was already written above). When I disconnected the battery, it disappeared (though not every time, sometimes I had to disconnect the battery again).

And you can probably check the fuel pump only by connecting it directly to the battery here: https://automan.by.ru/vaz/010/el102.shtml there is a diagram of its connection, or look in your Murzilka, otherwise the colors of the wires are poorly visible in the internet diagram . You can try connecting the wires to the pump block, and then to the battery for 1-2 seconds (but not the other way around, so that there is no spark at the tank). And you will find out everything.

if the fuel pump relay is triggered, then look at its power contact, is there any + if so, does + appear on the pump connector on the gray wire, if not, then most likely the signal blocking relay is somewhere, apply directly + to the gray wire

Finally started up. By the way, I made a whole discovery for myself: the presence of 12V voltage (according to the voltmeter) at the fuel pump connector does not mean anything. The voltmeter shows 12V after turning on the ignition (4-5 seconds until the relay operates), the 12V light (working) on ​​these contacts does not light up. When connecting the pump directly to the battery, everything works. Further searches led to a thorough check of the fuel pump relay and fuse, tightening the ground bolts on the engine. And when this did not help, I had to pay attention to the alarm. Although it was turned off. Numerous switches on and off, with or without sound, with switching to “Valet” mode and exiting it, did not yield anything. Everything worked as expected. And only a thorough check of the alarm relay (the relay brand is “Saturn”) revealed that if 12V is supplied to the relay, it always clicks, but the light bulb connected to it sometimes does not light up, and sometimes it does not light up immediately, but after some fractions seconds. There were 10 percent of such incorrect responses. After installing a jumper on the relay, the fuel pump started working and the car drove. I went to the car service center. Today, for 2.5 hours, the car service specialists racked their brains (they didn’t install the alarm), removed my jumper, came to the conclusion that it was better to replace the relay, checked and cleaned all the contacts of the accompanying relays and fuses, tightened everything up and returned the car. It starts as before, with half a turn. No obvious faults were found. For the work they performed, they charged me 208 rubles on a receipt. That's the whole epic for now.

Lada Priora error P1602. Phase sensor error. Increased fuel consumption. How to fix.

Let's take a closer look at such an error as P1602, it means that the power to the ECU Electronic Control Unit is lost. I purchased this device for a couple of thousand rubles:

This is an on-board computer, it fits many cars. The cable for connecting it is included. It connects to an outlet located in the glove compartment. This on-board computer is capable of displaying numerous information about the car, fuel consumption, outside temperature, and, most importantly, errors. He immediately pointed out a faulty phase sensor. It is located under the hood and can be easily changed, although in a slightly vandal way. Here you can see one mounting bolt:

The second one is behind the phase sensor itself, there is no way to get to it. We unscrew the visible bolt, then prop it up with a screwdriver, breaking off the ear on the second bolt. After successfully replacing the phase sensor, this error disappeared, fuel consumption decreased significantly, until that moment it was 16-19 liters per 100 km. mileage, but a new error P1602 appeared. It signals to us that the power supply to the unit (Bosch 797) has failed. All masses were checked, everything under the hood is normal, the second mass is located under the foot air duct near the front passenger:

Next, we trace the wires, ground contacts are 80 and 61 on the block, plus 12:

After the diagnostics were carried out, a problem was identified in the 12 positive wire (red). The contacts are marked on the ECU itself. The problem with the positive wire was that the terminal at its end was slightly deformed and it was loose on the contact in the ECU itself, which resulted in error P1602. The repair was simple, this terminal was bent a little (this must be done carefully so as not to break it), after which the wire stopped hanging out, the computer signals that there are no errors.

Video error P1602, phase sensor error in Lada Priora:

Reserve video error P1602, phase sensor error, increased fuel consumption in Lada Priora:

What is this message

The Priora's on-board computer reports errors using special numeric numbers displayed on the monitor. Each of the coded messages indicates its own malfunction; translation of the code and details can be found in the manual. Error P1602 stands for loss of mains voltage in the controller. In some cases, this will lead to minor and unnoticeable deterioration in the performance and economy of the engine, in others it may simply refuse to work, and sometimes this error is translated not as “a loss of voltage from the on-board network,” but as “the sensor is faulty, do something with it.” Perhaps the last one is the easiest, although frequent error messages can get on your nerves. Computer crashes, unfortunately, are very likely.

Instructions for diagnosing VESTA via OBD2 connector with your own hands via a laptop or smartphone

Determine where the OBD2 connector is located

Determine which scanner is suitable for your car

The selection of a scanner (adapter) for LADA VESTA depends on the ECU model, as well as the needs of the diagnostician / car owner.

To select diagnostic equipment, use the calculator: “Selecting a scanner for Lada Vesta”

Download the diagnostic program for the scanner

The diagnostic adapter requires software that can be installed on a laptop or smartphone/tablet. Auto scanners with their own software shell and display do not require software.

To select a program for the adapter, go to the section: “Programs”

Use the instructions and carry out diagnostics

When you purchase an adapter, instructions are included with the adapter. More detailed instructions on diagnostic car scanners and descriptions of their operation are posted in the section: “OBD2 car scanner reviews”

Identify errors and decipher them

Error codes and their interpretation are displayed in the scanner program interface. You can also study the complete database of errors for your car in the section: “OBD2 error codes for Lada Vesta”

Make repairs according to the error code

The unit is repaired according to the decoding of the error (problem) or contact a car service to eliminate a particular malfunction.

Check errors again

Scan Tool Pro - budget multiscanner for Lada Vesta

A good choice for a novice diagnostician

Nowadays there are scanner models with different versions of firmware and chips on sale. Scan Tool Pro with firmware 2022 is the most stable version so far, and also has maximum compatibility with cars manufactured since 2001, including Lada Vesta.

Diagnostic methods for Lada Vesta

There are two types of reading errors from the memory of the car’s on-board computer.

1. Self-diagnosis - the on-board computer can show the motorist any existing errors. A simple procedure allows you to perform repairs without additional equipment. The disadvantage is the impossibility of determining the exact location of the breakdown or its system - the BC will only indicate the direction in which the defect should be looked for.
2. Using a diagnostic scanner is a complex procedure that cannot be done at home. For normal diagnostics, you will need to connect a laptop or tablet with a special program to the machine. Usually this is done exclusively in specialized workshops.

Let's remove these annoying numbers from the screen

Without exaggeration, the constant appearance of error P1602 on your VAZ-2114 car can be thoroughly annoying. Sometimes it seems that the car is mocking you, but do not forget that the car does not have its own decision-making center, and this is all on-board computer. Maybe he really has a wicked sense of humor. The simplest way to diagnose its performance is to simply replace one device with a similar one that is known to be working. The only problem may be getting another computer, but you don’t need it forever, you can just borrow it from a friend, simultaneously enlisting his services as an assistant, since he is so generous: what if the breakdown is in the machine, and not in the electronic brains , then extra hands will come in handy. If this error appears very often, you can try updating or changing the computer firmware. To do this, it is better to contact a specialist.

This error appears most often in winter, when the battery under the hood freezes. If the car starts after this, you can breathe easy: the likelihood of a false alarm has increased. But it didn’t disappear completely! To move forward, let's find out what kind of malfunctions may be hidden behind the P1602 code.

• the voltage of the on-board network has weakened;
• the power supply is almost running out;
• the network lacks power due to overload by extraneous devices;
• there is a short circuit somewhere in the wiring;
• violation of the integrity of the terminals or the circuit itself;
• one of the sensors to which the computer is connected is faulty.

Experts say that due to the initially low durability, the most common reason is the latter, failure of the sensors. They are inexpensive even by today's standards, so they are easy to replace; most importantly, do not confuse an outdated sensor with a working one!

Visually check the integrity of the wiring, reconnect the terminals, it is better to clean all contacts, even those that you do not suspect. This in itself can at least temporarily rid your VAZ-2114 of this error. Check the battery and its charge. If you don’t feel confident, you should entrust the generator diagnostics to professionals.

Lada Vesta ECU and suitable scanners

Vesta electronic control received a CAN interface. Brains communicate with various systems through digitally encoded signals. Moreover, the Itelm M86 ECU is easily coordinated with third-party security devices (alarms), GPS trackers, and multimedia systems. The only requirement is the presence of an appropriate data bus.

For diagnostics, reading indicators and errors, ELM327 automotive scanners are used. They also use other multi-brand devices that operate using the OBD2 protocol and CAN bus:

Diagnostic capabilities of LADA VESTA systems:

ECU location:

On this vehicle, the ECU is located in the engine compartment, on the right side (view from the front). Fixed with several screws to the shock absorber shell. The wire connection blocks are located at the bottom of the block, but the ECU itself is rotated 90 degrees. The tires are secured with latches. To remove the chip, unlatch the lock and remove the block.

By the way, removing the ECU is only necessary when flashing the controller firmware.

Chip tuning and firmware of Vesta ECU:

The original firmware is tailored to harmonize engine emissions with EURO standards. Chip units have modified software that disables some sensors (lambda) for high dynamic performance. You can find out the firmware type through OpenDiag. How to flash the ECU will be discussed below.