Do-it-yourself replacement of Lada Granta running light bulbs

AutoNews / Reviews / Tests

Replacing the Running Light Lamp on a Grant

How to independently replace running light bulbs on a Lada Granta
Among all the varieties of incandescent lamps, the running lights of the Lada Granda in the factory configuration have become known as more common ones. One of their main advantages was their affordable cost. Replacing a low beam lamp on a Renault Logan: photos and. Replacing a low beam bulb on a Nissan Qashqai (Nissan Qashqai) replacing a low beam bulb on a Nissan Qashqai how to change a low beam bulb (using the example of a Nissan Qashqai) In operation, Lada Granta lamps have quite a lot of shortcomings. One of them includes rather dim light with a pronounced yellowness.

About replacing running light bulbs

To improve the functioning and visual appeal of navigation lights, it will be quite a painstaking approach to the issue of replacing them and carrying out this work at the highest level. When choosing lamps, it is best to stick not to the standard ones, but to the LED subtypes that come without a base assembly. Replacing daytime running light bulbs on a grant basis. Replacing the daytime running light bulb etc. Such lamps can be purchased in virtually any specialty store. When choosing such lamps, it is better to give preference to models with a more striking lighting intensity.

Before replacing the lamps, you must first remove the old lamps from the Lada Granta and install new ones - LED ones. Unlike conventional types, when working with LED lamps, it is imperative to adhere to the power polarity.

In order for the installation process to be carried out correctly, you need to use a voltmeter, having previously determined the placement of the pluses and minuses. Replacing a low beam lamp on an opel astra j. Video. Checking the polarity is necessary in order to protect the fuse that controls the electrical voltage in the running lights circuit.

An even worse consequence in this situation may be that you will be left without the latest LED lamp at all. Replacing a low beam lamp on a suzuki gv 2.0 5dv, replacing lamps in the headlights through the fender liner of a suzuki grand vitara, replacing xenon low beam lamps. If the running lights are installed according to all the rules, then you are promised a comfortable ride in the Lada Granta with high-quality lighting.

What does the market offer?

Below are some options for halogen lamps of different price categories that can be installed on the Grant:

  • PHILIPS H4 COLORVISION . A set from a German manufacturer, characterized by bright light and the ability to choose the color of the glow (blue, green, yellow). Price – about $35.
  • OSRAM COLOR BLUE HYPER. Halogen lighting elements made in Germany, with a declared color temperature of 5000K. The flask is painted blue. Price – about 17$.
  • MTF LIGHT STANDARD. Korean light bulbs with a transparent bulb, the color temperature of which is 2900K, which allows them to be used in headlights with plastic housings. They will cost only $6.
  • KOITO DENSO VWHITE. Products made in Japan, with transparent bulbs and a color temperature of 3700K. Features high light intensity. Price – about 28$;
  • EVO VISTAS. Halogen lamps from China have a completely transparent body, their light color temperature is 3200K. Will cost $25.
  • LIGHTHOUSE ULTRA. Budget option made in China. The base is transparent, the characteristics of the products are fully suitable for installation on Granta. Cost – $4.

The process of replacing running light bulbs

  1. In the process of long-term use of a car like the Lada Granta, sooner or later the desire arises to make some changes to your iron friend. A significant role in the appearance of the car is played by lamps, which allow you to look at the road in a different, brighter light. This is a lighting device for daytime running lights. In cars of this brand, the function of such lights is performed by dimensional lamps. Before installing lamps on the Lada Granta, wipe their bulbs with alcohol-containing wipes. This is exactly how the running light bulb is replaced. Even minor tuning work on this part of the car will transform your car and make you look at it differently.
  2. Running lights can be modified very quickly - this is achieved by replacing halogen lamps with LED ones. When choosing LEDs, you should pay attention to the fact that they do not have a base. Note that replacing the running light bulb in a grant does not require any special skills, but the installation process still has several nuances.
  3. Just replacing a new LED will not be enough. To do this, you will need to tear off the base from the diode and direct the antennae into the required holes. How to replace the running light bulb on a Lada Granta. Don't forget to check the polarity when doing this. Replacing the low beam lamp, watch a video review of the low beam lamps for the Nissan Qashqai. As a result of these manipulations, you will become the owner of new running lights, and also get rid of the unpleasant yellow light.
  4. Do not forget that when performing any work on tuning headlights, you must adhere to the standards established by law. Lamps used to replace running lights and change lighting on the Lada Granta. At the same time, the car must regularly undergo scheduled inspections, which will avoid many troubles.
  5. After you remove the old lamps, do not rush to get rid of them, as it may happen that when checking for the possibility of installing new ones, they will turn out to be unusable, and you can replace the ones that were previously there.
  6. Another important point when buying lamps that is worth knowing is that the law allows the use of LEDs in only two shades - white and yellow.
  7. If your goal is not only appearance, but also the wise use of money, you should give preference to LED lamps, since they consume a minimal amount of electricity, which cannot be said about standard lamps.

When installing LEDs, the load on the car battery is significantly removed.

Main conclusions

In the standard version, the Lada Granta car is equipped with low-power incandescent light bulbs in the running light system, which are not distinguished by good brightness and durability. They can be replaced with the following alternative light sources:

The former belong to the category of increased visual comfort, have good brightness and quick installation. However, during installation they can easily be damaged by putting a grease mark on the surface of the flask; in addition, the more powerful they are, the less they last. LEDs do not have such disadvantages, consume less energy, save battery resources and are very durable. Their main drawback is the formation of blue highlights and the non-standard base, which complicates the replacement procedure. In addition, LED bulbs can trigger sensors on the dashboard.

Types and causes of breakdown

These devices have several types:

  • low beam headlights. Switched on while the vehicle is running. In Russia it is allowed to use them as a light source for daytime driving;
  • high beam headlights. Operate at reduced voltage. This helps to reduce the intensity of light, which in some cases does not increase the visibility of pedestrians and cyclists on the road;
  • fog lights. Their use in Russia is permitted (clause 19.4 of the traffic rules);
  • front turn signals;
  • individual light sources at the front of the vehicle with specific light intensity patterns.

The main manufacturers of high-quality DRLs are such brands as:

These and other models of light sources may differ in shape (rectangular, round, oval), the number of diode bulbs inside, power, and brightness.

Today, manufacturers have even begun to produce silicone diode bulbs suitable for the Lada Granta. They can be located on one or several tapes.

Among the main reasons why DRLs do not light up are:

  • lack of polarity check before installing light sources;
  • The turn signal channel does not light up;
  • fuse is blown;
  • lack of heating or burnout of the filament.

To improve daytime running light sources and make them extremely useful and stylish for the car enthusiast, you need to do all stages of the work as efficiently as possible. Instead of standard lamps, which do not burn very brightly, you can install LED lighting without a base assembly. You can buy these components in almost every store that sells car parts. At the same time, when making a choice, you need to focus on models with the highest lighting brightness.

Where and what lamps are used on Grant 1 and 2

To find out which lamp you need to buy for replacement, you need to study the table of lamps used in Lada Granta and Lada Granta FL cars. Also, this table will be relevant for models with a liftback and station wagon body.

Light typeApplicable lamp standard
Near/FarH4
Front/Rear turn signalPY21W
DRL and side lightW21/5W
Side turn signalW5W
Brake light and markerP21/5W
ReverseP21W
Rear PTFP21W
License plate lightC5W
Trunk lightingC5W
Interior lampC10W
Illumination of the heater control unit, cigarette lighterW1,2W
Front PTFH11

In order not to take out an old lamp and take it to the store, you just need to look at the desired light source in the table. Article numbers are not needed when purchasing light bulbs. It is enough to tell the seller the standard of the light source.

Installing new lighting

The necessary increase in brightness or service life of light bulbs can only be achieved by replacing existing lights. Car enthusiasts often replace the halogen lighting sources installed in Lada with LED ones. As a rule, even a person without experience in replacing lamps can cope with this task. However, you should know a few nuances. Simply placing a new diode in the right place is not enough - the process has its own characteristics. They are:

  • it is often necessary to tear off the previous base from the diode in order to move its parts to the required holes;
  • the driver will have to check the polarity of the light sources on the Grant to ensure the safety of the fuse. If this is not done, the fuse that controls the voltage in the network will simply blow out. The fuse that is installed in this car model is capable of de-energizing the safe operation of the electrical circuit.

Before changing light bulbs, you need to make sure that such a procedure will not violate current legal regulations.

You should also remember to undergo routine inspection. It will help determine whether the changeover procedure is dangerous. Once you take out your old light source, you don’t need to throw it away immediately. If you do not pass inspection with new lamps, it would be logical to return the old ones in their place. Also remember that the legislation of the Russian Federation allows only white and yellow lighting on cars - other colors are illegal.

Changing the lighting on the Lada Grant to the recently popular LEDs provides many advantages:

  • consumption of less electricity and, therefore, fuel;
  • longer service life (some are designed for the entire life of the Lada Granta);
  • excellent visual effects, bright road lighting;
  • These models do not put a large load on the generator and do not overload the fuse.

To replace the right headlight, follow the algorithm:

  1. Remove the cartridge by rotating it counterclockwise.
  2. Remove the broken product by pulling it towards you.
  3. Check that the bulb's antennae match the same mounts in the car and insert it into place at a 45-degree angle. Correct placement of diode antennae

Installing lighting in the left headlight has its own characteristics, since it is more difficult to reach. Before the replacement process, remove the air filter unit by first unscrewing the antifreeze hose. After this, remove the 3 rubber fasteners that secure the block. Further actions are similar to replacing the lighting in the right headlight.

Daytime running lights are a type of optics used to identify a vehicle on the road at any time of the day. Since the installation of this lighting is mandatory in our country, our compatriots have many questions regarding their operation. Read more about in what cases the DRL lamp of a Lada Granta W21/5W is changed and how to replace it yourself.

Common DRL faults

What are the signs of a malfunction of Grant's DRL:

  1. The glow of the LED elements has become dimmer. If this problem appears on only one headlight, then it is necessary to check the wiring and the quality of the contacts, although the possibility of wear cannot be ruled out. If both lights begin to burn dimmer, then most likely the problem is that the optics are close to failure as a result of having reached the end of their service life.
  2. The running lights do not turn on. In this case, the problem may lie in the inoperability of the optics, poor contact with the electrical circuit or damaged wiring. The reason can also be found in a non-working switch or DRL activation button.
  3. The diode elements do not light up, but blink, and the light may disappear. Such problems are usually caused by poor contact between the optics and the on-board network or worn-out light bulbs (video author - Alexander Kordyukov).

We provide access

The peculiarity of the work on replacing lighting elements on a Lada Granta is that the bulbs are removed from the inside of the headlight (under the hood on the engine side) and the space for their location is limited.

To improve the convenience of operation, some elements can be removed from the power supply to facilitate access to light sources.

So, to improve access to the left lamp (driver's side), you can unscrew the air filter housing and move it to the side.

What kind of lighting do you prefer?

Built-in Chandelier

As for the right headlight, the engine protection cover on this side can be removed by unscrewing the oil filler cap and pulling out the clips. In this case, after removing the engine cover, the oil filler cap must be replaced.

Please note that it is not necessary to remove these items from the engine. If you have the skill, and the driver has already made the replacement and knows the specifics of the work, then it is quite possible to perform this operation without disassembling any elements from the engine.

Does it make sense to change working running lights?

Many car owners are interested in the issue of replacing standard DRL bulbs with more advanced ones, since the former are characterized by certain disadvantages:

  1. Dim lighting with yellowish tint. Firstly, in practice, such light often spoils the aesthetic appearance of the car as a whole, and secondly, its lighting does not have the best effect on the visibility of the car in front.
  2. Low service life of such lighting sources. So sooner or later you will have to face the need to replace light bulbs.

It is for these reasons that our car owners decide to replace traditional incandescent lamps with more advanced lighting sources. If you decide to install diode light elements instead of incandescent lamps, then when choosing, you should pay attention only to their base - replacing a light bulb involves using the appropriate connector (the author of the video is the City&Country Style channel).

It should also be noted that the main disadvantage of DRLs is that this type of optics is not fixed in any way in the current legislation, in particular, we are talking about lighting sources. Therefore, you must be prepared for the fact that you may encounter an inspector who wants to fine you for this. It must be taken into account that certain types of lighting devices must be manufactured in full compliance with GOST and standards. So if the technical specifications of the light bulbs being installed do not match those that should be installed, then this is fraught with possible problems in the future.

Which brand of fog lights should I choose?

There are enough companies on the global market that produce lighting devices for cars. Many of them have a long history of development and significant achievements.

However, the ranking also includes young companies that have achieved recognition among users and authority among competitors in a short time.

The best, according to consumers, are considered to be manufacturers from Germany, Japan, Poland, and China, who sell their products under the American brand.

Hella and Osram are German companies founded more than a century ago. The first owns 100 companies in Germany and the same number in the other 35 countries of the world. The second owns 44 patents for production technologies for a wide variety of lamps.

PIAA is one of the world leaders in the manufacture of halogen lighting elements - the corporation was founded in Japan in 1963.

Wesem is a Polish company that has entered the foreign market since 1977. Supplies modern lighting equipment for almost all types of transport, including combines.

Morimoto is a well-promoted American brand whose mark is on carefully quality-tested xenon lenses from China.

Legend

DesignationsUnitsNames
HLamp base
PWPower
UINVoltage
Gcm|cm|cmDimensions
CC thousand ₽Price as of 01.2017

Replacement instructions

So, if you want to achieve a better glow and increase the service life of your optics, just change the lighting sources in it. As practice shows, the most popular option in this regard is to replace traditional halogen lamps with diode light sources. But before you begin this process, you need to understand that simply installing a diode instead of a halogen will not be enough .

After all, this process has certain features:

  1. Typically, for installation it is necessary to tear off the base previously installed on the diode element in order to transfer it to the required hole.
  2. Replacing Lada Granta DRL lamps also involves checking the polarity of the lighting sources in order to maintain the functionality of the safety element. If you do not do this, the fuse will fail in any case, thus de-energizing the safe operation of the on-board network.

The replacement procedure is as follows:

  1. First, you need to turn off the ignition, open the hood of the car and disconnect the terminals from the battery. This will allow you to turn off the device and ensure further safe operation when the power supply is de-energized.
  2. Let's start the replacement with the light sources in the right lamp. To do this, pull out the cartridge; to do this, you need to rotate it counterclockwise.
  3. Then the failed lighting source must be removed from its seat; to do this, simply pull it towards you.
  4. After completing these steps, make sure that the antennae on the removed bulb correspond to the location of the contacts on the new one. The antennae themselves should fit into the mounts on the optics without any problems. Install the new lighting element at a 45 degree angle.
  5. Next, the lamps in the left headlamp are replaced. Here the procedure will be slightly different, since it has its own characteristics, in particular, it will be more difficult to reach the light bulb. Before changing devices, it is necessary to dismantle the air filter unit; to do this, disconnect all fasteners and clamps, as well as pipes. It will also be necessary to unscrew the pipe through which the coolant passes. The block itself is supported by three special clamps; they must be removed.
  6. After completing these steps, you will need to repeat all the replacement steps described above. Further assembly is carried out in reverse order. Now all you have to do is connect the battery and check the functionality of the optics.

Price issue

The cost of a set of lamps or the daytime running lights themselves can vary greatly depending on the manufacturer and place of purchase. Below are the average prices for headlights, as well as lighting sources that can be purchased on the Russian market.

Review of work features

First, let's look at the simplest case and figure out how to replace a low-beam lamp on a Grant, then we'll tell you how to troubleshoot some problems, and we'll describe how to adjust the light yourself; the instructions are so simple that anyone can handle it.

Replacing light bulbs

The low beam lamp of the Lada on Granta is universal, that is, it serves both high and low beam. The 60/55 Watt option is used (that is, the power of the high beam spiral is 60, and the low beam is 55), the lamp type is H4. This is the option you need to purchase before starting work.

The process itself is quite simple, and replacing the low beam bulb on a Lada Granta is done very quickly:

  • First, remove the terminal from the battery and fix the hood in the open position.
  • Next, press the latch of the plastic plug on the headlight and open it.

The lid latch is located at the top and is clearly visible

Under the cover you will see a block with wires; it must be carefully disconnected and moved to the side.

  • Next, remove the rubber plug, which protects the case from moisture and dust. The rubber plug is very easy to remove
  • The low beam lamp on the Grant is held in the reflector by a spring lock; to release it, you need to press the antennae and disengage them from the hooks of the housing.
  • After this, you can remove the used unit, but we recommend that before changing the low beam lamp on Grant, you carefully examine it; it is possible that it is working, and the reason for the lack of light is not at all in it.
  • When installing a new unit, do not touch the glass part under any circumstances, as this can cause it to fail very quickly; do everything carefully. Assembly is carried out in reverse order. (See also the article Installing fog lights on Kalina: features.)

Replacing the low beam lamp on a Lada Granta is done very carefully so as not to touch the glass bulb

Shutdown problems

Very often you can come across this question: the low beam headlights on the Lada Granta do not turn off, what should I do?

In fact, there may be several reasons, we will look at them:

The low beam relay on the Grant is located in a common block, the diagram below shows its location, you can try to hit it lightly, this often solves the problem, but you still need to change this unit, especially since its price is low. This is the most common option, but far from the only one.

The main reason why the low beam on the Lada Granta does not turn off is interruptions in the operation of the relay indicated in Figure K4

  • The second option is a malfunction of the steering column switch; you can check it very simply: remove the trim from the steering column and disconnect the block of wires that go to the switch unit. If after this the light does not go out, then everything is fine with it; if it goes out, this unit needs to be changed.
  • Finally, the third option is a short circuit, which can occur due to wear and tear of the elements or the use of too powerful light bulbs. To check, move the chip on the headlight. If the light blinks, then this is the reason, you need to unscrew two screws to disassemble the housing, most often the low and high beam contacts are closed, just disconnect them and put them back as they should be.

Adjustment

Let's look at how to adjust the low beam headlights on a Grant yourself:

First, you need to carry out preparatory measures - refuel to a full tank, check that there is a spare tire in the trunk, and put a load weighing 75 kilograms on the driver’s seat. Also, check the tire pressure, it should be correct.

Tire pressure is an important parameter; if it is different, the car will not be level and it will not be possible to make the correct adjustment.

  • You will also need a 6 mm hexagon with which the adjustment will be made.
  • You need to find a flat area in front of which there is a wall or a flat high fence and place the car at a distance of three meters from the surface.
  • Apply markings on the wall - two vertical stripes should go along the width of the light bulbs in the headlights, a horizontal line should be located along the height of the installation of the lighting elements, and also draw an axial vertical line in the middle.
  • When adjusting one of the headlights, cover the other with opaque material, then set the corrector to position “0”. Next, use a hexagon to direct the light flux so that its center is at the intersection of the vertical and horizontal lines opposite the headlight. Work is also carried out on the second side.

The hexagon is inserted into the hole above the headlight and the screw is carefully rotated to the desired position

Is it worth replacing a working running light bulb?

But such lamps have more than enough disadvantages!

  1. Including dim light with a yellow tint, which does not have the best effect on visibility in front of the car.
  2. And, of course, it is important to remember about the service life of such lamps, which will turn out to be very short.

All this forces people to change the running light bulbs in their cars almost immediately after purchase.

In principle, replacement may also apply to new incandescent lamps if the old ones fail. But, nothing prevents you from using LED lamps. Pay attention only to the base, which must correspond to the connector that is supposed to be in the car.

But, in this case, you also need to remember that simply replacing an incandescent or halogen lamp will not be enough, since you need to tear off the base from the diode in order to redirect the antennae to the desired connectors. Naturally, before the procedure you will need to check the correct polarity.

Analysis of reviews from Lada Granta liftback owners

  • Grant-Eject (https://www.drive2.ru/l/6512513/): the sedan's lamps are different from those of the liftback. In the first modification they are combined, in the liftback they are separate.
  • Diyk: taillights often sweat on sedans, the problem has been eliminated in the liftback;
  • Silica Gel: to quickly remove moisture, attach a moisture absorber for shoes to double-sided tape. It doesn't last long, but it's effective. Improving the sealing of the rear lights is an alternative option.
  • Grant-Eject: insufficient fixation contributed to the flashlight falling out during movement.
  • LADA Granta 2012 (https://www.zr.ru/content/articles/832528-lampy-primenyaemye-v-avtomobile-lada-granta/): the car is reliable, unpretentious, subject to a moderate driving style. Over a period of five years of operation, breakdowns are typical and characteristic.

DRL lamp replacement process

  1. To gain the necessary access to the left headlight unit , you need to move to the side the housing, inside of which the engine air filter is located. For this purpose, we dismantle all housing fastenings, wiring harnesses and sensor. After this, you can slide the filter housing up.
  2. But to gain access to the right headlight unit , you will need to remove the power unit cover. To do this, you need to unscrew the oil filler cap, and then carefully snap off the cap. This is done with a confident upward movement. The main thing is not to forget to screw the lid back into place in order to prevent the possibility of solid objects falling into the neck, including dirt, which can be quite a lot under the hood.

As for the headlight lamp connector, it is located closer to the lower corner of the headlight. So, you will need to remove the cartridge. This is done by turning the cartridge counterclockwise. Now you will have access to a lamp, which is very easy to replace.

Installing a new lamp occurs in the reverse order. The main thing is to get the cartridge into the corresponding groove on the headlight, but turn it clockwise.

Disadvantages of LED lamps

If you decide to install LED lamps, then be prepared for some problems with their operation.

Basically, we are talking about the fact that the sensor on the instrument panel will constantly indicate problems with operation. The reason for this is the reduced electricity consumption of such lamps. This is noticed by a monitoring relay, which constantly monitors the normal operation of the lamps. So, seeing a reduced current supply, the driver will be shown a corresponding message that the lamp has become unusable.

The indicator will be constantly lit on the instrument panel, or the on-board system will sound an audible alarm. However, the sound signal will only be heard in a situation where the instrument panel is replaced with a similar one, but of a European version.

In addition, if you replace a yellow LED without chromaticity with a white one, it can additionally include various shades, ranging from blue to purple. This may cause a natural reaction from government officials. So, it can be very difficult for you to prove that LEDs meet legal and safety regulations.

Installation Requirements

The key disadvantage of daytime running lights is that they are not fixed in legislation as a standard lighting device. So, many conflicts may arise between vehicle owners and government officials.

Special types of lighting fixtures must be manufactured in strict accordance with state standards. Therefore, if an independent replacement was carried out, then the new lamps, in terms of their technical characteristics, must comply with the established standards.

For example, for a Lada Granta car, daytime running lights must be located in the front part at a height of at least twenty-five centimeters from ground level.

Video on how to ensure bright DRL lighting in Grant without modifications

Good visibility on the road, especially in the dark, is a guarantee of safety. A correctly installed lighting system is extremely important for a car; the issue of uninterrupted operation of high and low beam headlights on a Lada Granta car is always relevant.

In today’s article we will talk about the malfunctions and causes of failure (burnout) of low beam lamps on Lada Granta cars, we will look at what to look for when choosing, and I will also tell you step by step how to replace this undoubtedly important element of the car.

Most often, Granta owners complain about the fairly frequent failure of low beam lamps. Indeed, they most often require changing names, which is understandable: after all, they work almost constantly.

If previously car owners turned on the lights at night and in inclement weather, now, according to the rules, they must always be on while driving. Lamps do not last forever, and if a cheaper analogue is purchased to replace the fairly good standard OSRAM light bulbs, the problem may become a regular one.

LED lamps for Lada Granta SMD 2835

The second common reason for bulbs burning out in front and rear headlights is moisture getting inside. The culprit is usually cracked or poorly fitting rubber seals located between the headlight housing and the glass. The presence of a problem is indicated by periodic fogging of the headlight from the inside.

Halogen lamps may not light due to improper installation. During this procedure, you must avoid touching the glass surface with your fingers.

Traces of grease significantly reduce the life of the light bulb. In addition, although in rare cases, the lamps do not light up due to too high voltage supplied by the car's alternator or poor terminal contact.

LED halogen lamps on Lada Granta H4 (prohibited for use)

In general, as you were able to notice, there may be more than enough reasons why the low beam on the Lada Granta stopped working. Let's now figure out in what cases you will need to replace the lamps, and in which cases you should contact a specialist.

Replacing low beam lamps on a Grant may be necessary if they burn out. But, if such a malfunction occurs very often, or along with the low beam, any other part directly related to the electrical system disappears or stops working, then in this case it is better to contact a specialist.

The process of replacing low beam lamps on a Lada Granta

In most cases, the problem lies in the car's wiring or insufficient voltage supplied by the battery. It will be extremely difficult to find the cause on your own without the proper skills.

Replacing light bulbs in the front headlights of a Lada Granta car is usually carried out due to natural wear of the lamps (clouding of the bulb) or their complete failure.

Every car owner should be able to carry out the procedure for replacing low and high beam bulbs, since the lighting elements may fail along the way and further movement without lighting will become impossible. The Grant headlights use halogen double-filament lamps with an H4 socket (the new family of models uses lamps with an H19 socket).

One lamp, thanks to the presence of two filaments in it, allows the headlamp to operate in two lighting modes - low beam or high beam. No special tools are required to carry out the replacement. You will need a long screwdriver, rags, cloth gloves and alcohol to wipe the lamp bulb. The replacement process should only be carried out with clean gloves.

To gain free access to the left block, move the housing that covers the air filter and protects it from external factors. To do this, you will need to remove all the harnesses and housings from the device, and then simply move the desired housing up.

With the right block the situation is somewhat different. In this case, to replace the running lights on the Lada Granta, you will need to dismantle the power unit cover. To do this, first remove the cover of the oil filler system, after which the desired housing is snapped off. It is worth noting that the cover can be firmly fixed, so you should firmly pull up to remove it.

Adviсe

If you notice that your running light bulbs burn out too often, the reason may be due to errors during replacement. The fact is that you cannot touch the bulbs of halogen lamps with bare hands. It is best to work in new cotton gloves that are free from dirt and other defects. The fact is that greasy marks that will remain on the lamp bulb can reduce the overall service life by up to several times. And to remove dirt, you just need to wipe the flask with a cloth previously moistened in an alcohol solution.

And, of course, do not forget that after replacing the lamps you may need to adjust the headlights.

  • January 11, 2016 11:30:17
  • Reviews:

daytime running light lamp is combined with the dimensions. Standard socket 4 pin w21/5w. 21 W – running lights, 5 W – dimensions. It seems like install an LED lamp of this size and that’s it. But no...

AvtoVAZ loves to come up with the best schemes and non-standard solutions. It's the same this time. The pinout on a standard base is completely non-standard. Therefore, if you install an ordinary LED lamp , then the following options are possible: either the running light (or dimensions) will not work, or it will start to smoke..

There are several options for solving this problem.

Option 3. The most barbaric. Drill out the entire base from the standard Granta connector. Glue the light bulb there tightly and either solder the wires as needed, or buy an additional connector and solder it on it.

The most correct option is to use special non-polar LED lamps . This means that no matter how “+” and “-” are supplied, the electronics inside the lamp will determine how to supply power to the chips.

Rate it! Luminous flux - 720 Lm (halogen low beam lamp gives a flux of 1200 Lm) Chips - American made CREE, 6 pcs Multi voltage from 12 to 24 V Non-polar Claimed service life of more than 30,000 hours.

The photo shows the fuse for daytime running lights on a Lada Granta . When experimenting and selecting LED lamps, it often burns out.

For comparison. One headlight of the Lada Granta car has an LED DRL , the other has a standard lamp.

And now how it looks in the dark. The difference is obvious!

LED running lights and low beams on. Well, in general, the low and high beams also need to be changed to LED lamps. For example, for these – LED CARS H4 HI/LO 3600 LM

Rating
( 2 ratings, average 4.5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]