Diagnosis of faults, repair and replacement of the VAZ 2110-12 oil pump with your own hands

Purpose

The purpose of the oil pump is to circulate oil through all engine components to lubricate them evenly and increase their service life. It is driven by an internal combustion engine (internal combustion engine) and is structurally divided into two different types, based on the principle of coupling with the crankshaft. In our case, it connects directly to the crankshaft, that is, it rotates with it. This is the operating scheme of the unit for front-wheel drive VAZ cars. Cars with all-wheel drive, as well as classics, have a more complex system installed. There, the drive contains additional links: an intermediate shaft, a timing chain (gas distribution mechanism), and toothed gears, through which torque is transmitted from the crankshaft to this device.

Common faults

So:

• Most often, the pump of the VAZ 2112 and other VAZ models with front-wheel drive leaks through the seal, which has to be changed.
• The oil receiver also often fails, especially if you use low-quality oil, or missed replacing it in a timely manner, or the oil does not meet specifications (too thick).
• Too liquid simply will not be pumped and the pressure sensor will immediately light up.
• In this case, the oil receiver mesh becomes clogged, the circulation of oil through the engine becomes difficult, causes oil starvation, and as a result, the service life of the engine is significantly reduced.
• This includes a malfunction of the pressure reducing (bypass) valve: either it is stuck in the open position, and then the oil pressure drops. Either it does not bypass, and then the oil will squeeze out through the oil seal

What oil to fill and at what frequency?

The manufacturer recommends changing the engine oil after 10 thousand kilometers, however, it is recommended to shorten this period if possible, and at the same time change the oil filter. You should only buy oil from well-known companies and, when choosing it, beware of counterfeits. The ideal option is to pour oil recommended by the manufacturer and not be fooled by cheapness or high cost (expensive does not mean high quality).

Recommendations for choosing spare parts

So:

• The oil pump usually does not cause car owners much trouble, since it has a service life of at least 120 thousand kilometers. However, no one is immune from breakdowns
• If suddenly you still need to replace the oil pump on a VAZ 2112, it is better to take original spare parts and not save
• Among the well-known suppliers of parts for VAZ cars, the official one is the Tolyatti Automobile Assemblies Plant (TZA for short).
• It also produces oil pumps for the VAZ 2112
• This is one of four varieties of such units in the VAZ line, which fits all front-wheel drive fuel-injected cars

Helpful advice: To avoid serious consequences for the car and major engine repairs, it is important to monitor the indicators on the dashboard. If the oil pressure lamp flashes at idle speed, and replacing it does not solve the problem, the lamp lights up again - this means there is a breakdown

When the warning light suddenly comes on and the performance of your car’s engine is alarming, it is recommended to turn off the ignition and call a tow truck to a repair station. This will save money on subsequent engine repairs (continuing to drive the car under its own power in such a situation, you risk serious damage to the engine).

• Typically, removing the oil pump on any car occurs when disassembling the engine.
• Only if necessary, this work is carried out on the car without removing the engine from it.
• Before starting this procedure, first drive the car into the inspection hole.
• And immediately purchase everything you need to carry out a full replacement, as shown in Photo No. 2.

Designations in the photo:

• 1 - oil pump
• 2—pan gasket
• 3 - pump gasket
• 4 - sealing ring
• 5 - sensor mounting bracket

Attention: The pumps of the VAZ 2108-1011010 and 2111, 2112-1011010 engines are almost the same, with the exception of point No. 5 - the sensor mounting bracket is different, do not miss this point!

Tip: It is recommended to install only a factory-produced gasket under the pump, since a non-standard gasket may have a thickness that does not meet the specifications and cause problems with the operation of the pump.

Necessary tool

• A set of wrenches (open-end - spanner preferably)
• Socket set and ratchet
• Two strong flathead screwdrivers
• Hexagon set

Causes of oil pump failure

There are a number of typical breakdowns due to which the oil pump completely or partially fails:

• physical wear of the housing, rotor or driven gear. There is a gap of 0.2 mm between the pump gears and the housing. There is also a gap between the teeth of the pump gears - 0.5 mm. As wear occurs, these gaps increase, and the pressure created by the pump at the outlet pipe drops. Since replacing and adjusting worn gears is a very labor-intensive process and not everyone can do it, car enthusiasts follow the path of least resistance and simply change the entire oil pump;
• clogging of the oil receiver. If it becomes clogged, the pressure in the car's lubrication system drops sharply, and a red light comes on on the dashboard. A clogged oil receiver is a consequence of a completely clogged crankcase. The solution is to completely drain the used lubricant, remove the pan, crankcase, oil pump and thoroughly wash all these parts in kerosene;
• oil leak. Sometimes oil begins to leak directly from under the pump. Typically, the driver does not notice a leak immediately, identifying it by indirect signs, for example, by a sharply increased lubricant consumption and oil stains under the car. The cause of the leak is a leak in the pump gasket. Often, when replacing an oil pump, car enthusiasts do not change the gasket located under it, believing that it will serve for some time. This is an error that leads to leaks. The rule is simple: when changing the oil pump, you must also change the gasket, even if it does not look worn out.

Separate mention should be made of motor oil. Its quality also has a significant impact on the service life of the pump and its serviceability. The fact is that the oil pump is the only engine element that is lubricated with unfiltered oil (because the oil filter is installed only on the pump outlet). And if the car owner is used to saving on high-quality oil, then he may not count on long and uninterrupted operation of the oil pump.

Common unit breakdowns

• operational wear of the components of the unit: the pump housing or gears fail: during the operating cycle, the gap between the driven and driving gears increases. In normal condition it does not exceed 0.25 mm. Wear leads to the fact that the distance between the parts increases to 0.5 mm: the gears no longer mesh. The described breakdown makes the oil pump unsuitable for routine repairs - it is easier to buy a new part than to install new gears and adjust them;
• leakage: oil begins to leak from under the pump. The reason for this is a leaky oil pump gasket. Replacing the gasket solves the problem;
• Oil receiver clogged: The oil receiver becomes clogged due to a clogged crankcase. In this case, you need to dismantle the oil pan and clean the mechanism.

In most cases, it is necessary to purchase a new oil pump. The price of a new part in online stores is in the range of 1700 - 2500 rubles. The devices are compatible with the first generation Samara.

Signs and causes of oil pump malfunction Lada 2114

There are several markers, the appearance of which will allow you to suspect defects in the pump:

• The corresponding light on the dashboard lights up;
• Oil puddles regularly form under the car;
• Smoke is generated during engine operation.

Causes of unit malfunctions:

• use of motor oil that does not comply with the car manufacturer’s recommendations;
• oil filter clogged;
• permanently low level of lubricating fluid in the crankcase;
• non-working condition of oil level monitoring devices;
• failure of the engine lubrication system valve;
• impurities entering the engine oil (most often coolant is mixed with it).

All the described breakdowns are accompanied by activation of the control lamp, so do not delay repairs; begin service operations after activating the control indicator.

How to check oil pressure?

The actual check is carried out using a special device - a pressure gauge. It is also worth noting that you need to warm up the engine to operating temperature, usually 90 degrees Celsius.

If you measure with a cold engine, especially in winter, the pressure can jump to high values, from 0.5 BAR or even higher, but measuring with a cold engine is WRONG!

In order to check the pressure, you need to find the emergency sensor, which is responsible for the indication on the dashboard. It is worth noting that it is not always located nearby and it is convenient to unscrew it. We unscrew it, and in its place we attach the test output connected to the pressure gauge.

The check can then be divided into two options:

• AT “idle” it is usually from 900 to 1200 rpm.
• Then at “higher” speeds, usually 4000 - 5000 engine speeds.

It is also worth noting that if you unscrew the emergency sensor, the “oil can” will light up on your instrument panel, this is normal.

Now a short video showing how measurements are taken.

Filming

• First you need to disconnect the negative cable from the battery.
• Draining the oil from the engine
• We take out the camshaft drive belt

• We take out the crankshaft toothed pulley, then its key, using two flat-head screwdrivers.
• Then remove the oil sump.
• Unscrew the oil intake mount.
• Using a 10mm socket with a ratchet and an extension, unscrew the six bolts securing the oil pump to the cylinder block.
• Remove the unit from the engine.

Be sure to wash the new oil pump with gasoline to remove grease for preservation. We fill it with oil before installation so that it does not rotate dry when starting. It is also important to turn the drive gear in order to place the pump on the crankshaft: so that the protrusions on the gear coincide with the groove on the crankshaft. Lubricate the seal lip with oil before putting the pump back. Carefully tuck the working edge of the oil seal onto the shaft journal using a wooden stick. Be careful and attentive when tightening the bolts so as not to strip the threads. Proceed in reverse order, install the remaining parts.

As can be seen from the above, this is not such a difficult job. The main thing for her is to approach it correctly and creatively. After all, proper lubrication is the basis for the longevity of a car.

Step-by-step instructions for repairing and inspecting oil pump parts:

1. For a detailed inspection, it is necessary to remove the oil pump.

2. First, you need to unscrew the bolt (1) and remove the crankshaft position sensor (2), which is only available on engines with a fuel injection mechanism.

3. When disassembling the pump, you need to unscrew the six bolts and remove the pump cover.

4. Using two screwdrivers, you need to lift the pump housing so that the pins on the housing can come out of the holes located in the cover of the VAZ 2110 oil pump. Now remove the housing itself by disconnecting it from the cover.

5. We take the gears out of the cover: first the driving one, and then the driven one.

6. Now you need to unscrew the pressure reducing valve plug. An O-ring must be installed under this plug. Inspect the ring - if it is too compressed, it needs to be replaced.

7. Having unscrewed the plug, we take out the spring of the pressure reducing valve.

8. Now we take out the valve itself, gently tapping the body on a clean wooden stand. If the valve does not come out, it must be removed using a thin pointed object, preferably also wooden, so as not to damage the surface.

9. Now you need to carefully inspect the aluminum cover for visible signs of wear, mechanical damage, deep scratches in the contact areas of the gears. If found, the cover must be replaced with a new one.

11. The size of the maximum permissible diameter of the driven gear socket is 75.1 mm, so we measure the diameter, and if it exceeds the permissible one, we will also have to replace the housing.

12. Now you need to measure the width of the body segment in the middle part. If the measured value is less than 3.4 mm, the VAZ 2110 pump housing must be replaced.

13. Check the gears. The thickness of the drive should not be less than 7.42 mm. We measure: if it is less, we replace the gear.

14. The same applies to the slave. If the thickness is less than 7.35 mm, the gear must be replaced.

15. Then we check the axial clearances of the gears. It is necessary to install the drive gear back into the housing, after which we apply a steel ruler to the housing and use a feeler gauge to measure the gap between the gear and the ruler.

16. In the same way, measure the axial clearance between the attached ruler and the driven gear. For the drive and driven gears, the maximum permissible axial clearance is 0.12 mm and 0.15 mm, respectively. In cases where these values ​​are exceeded, the gears must be replaced with new ones.

17. Through calculation, more accurate values ​​of axial clearances can be obtained. To do this, a micrometer is used to measure the thickness of the oil pump housing along the outer surfaces, as well as the thickness in the area of ​​the sockets for the drive and driven gears along milled surfaces in several places. The axial clearance is calculated based on the difference between the arithmetic mean of the socket depth and the measured thickness of the gears.

18. The next stage of repair is to inspect the pressure reducing valve seat to detect rough scratches and other deep mechanical damage on the inner surface. If found, the cover must be replaced.

19. If burrs and deep mechanical scratches are detected on the pressure reducing valve itself, it must also be replaced with a new one.

20. We also replace a bent, broken/broken or cracked pressure relief valve spring. The height of the spring in its free state is normally 44.72 mm; the same parameter under a load of 4±0.24 kgf is 31.7 mm. If there is a discrepancy, the spring must be replaced.

21. Assembling the oil pump. We install the driven gear with the chamfers on the teeth towards the housing.

22. Then install the drive gear in the same way - with the chamfers on the teeth facing the body. The gears must be lubricated with engine oil before installation.

23. Now you need to install the cover on the body and tighten the fastening bolts.

24. Before installing the pressure reducing valve into the seat with the bottom down, it must be lubricated with engine oil. Then you need to install the spring and tighten the plug with the aluminum O-ring of the oil receiver tube, also pre-lubricated.

25. It is necessary to pour engine oil into the pump through the oil receiver tube.

26. At the end of the repair and complete assembly of the car’s oil pump, turn the gears several turns so that the working surfaces of the gears are well lubricated.

Engine diagram and structure

Many motorists know the structure of the main power unit, but not everyone remembers it. In order to understand how the process itself occurs, let us recall how the engine works.

Engine diagram

1 - channel in the cylinder block for supplying oil to the oil line of the cylinder head; 2 — channel in the cylinder head; 3 — pipe for exhausting crankcase gases into the air filter housing; 4 - oil filler cap; 5 — exhaust hose pipe; 6 — pipe for removing crankcase gases into the throttle space; 7 - oil line in the cylinder head; 8 - camshaft; 9 — oil supply channel to the camshaft bearing; 10 — oil pressure indicator sensor; 11 — pressure reducing valve; 12 — channel for supplying oil from the filter to the main oil line; 13 - oil pump drive gear; 14 — driven gear of the oil pump; 15 — oil supply channel from the pump to the filter; 16 — anti-drainage valve; 17 — cardboard filter element; 18 — oil sump; 19 — oil receiver; 20 - drain plug; 21 - bypass valve; 22 — oil filter; 23 — oil supply channel from the crankshaft main bearing to the connecting rod; 24 — oil supply channel to the crankshaft main bearing; 25 - main oil line

How does engine lubrication occur (diagram and explanation)

Engine lubricant circulation diagram

So, when the issue of engine design has been considered, we can proceed directly to the consideration of lubrication. The system itself is considered combined.

Using pressure, the following are lubricated: main and connecting rod bearings of the crankshaft, camshaft bearings, cylinder walls (using splashing), pistons and oil scraper rings, the camshaft itself, valves and pushers.

The oil pump is located inside the engine, and only the cover cap is visible from above. The oil pump drive is mechanical, forced.

Schematic representation of oil circulation

Replacing lubricant

In order to change the oil, you will need a tool, 5 liters of oil (about choosing oil here) and an oil filter.

Shel Helix oil recommended for filling into the 10 series Lada engine

So, let's look at the sequence of actions:

We remove the lower engine protection (if there is one, of course). Unscrew the oil pan drain plug.

We wait for the oil to drain. While the liquid is leaking out, it is necessary to replace the filter.

To do this, use a special tool to unscrew the filter element. You need to pour a little oil into the new filter and screw it in place of the old one.

It is worth noting that between the motor and the filter there is a copper o-ring, which also needs to be replaced.

We tighten the drain plug. Unscrew the filler plug.

Using a funnel, we pour new oil into the system until the fluid indicator on the dipstick is between the MIN and MAX indicators.

What builds up oil pressure in the system?

Everything is simple here - there is a special oil pump that takes oil from the engine sump and pumps it through the system. It is usually installed in the engine sump and driven by special gears that the engine turns during operation.

Oil through many channels begins to be supplied to the right places under pressure, as I already wrote, this is the crankshaft and its bearings, the camshaft and its “bed”, pistons, and much more.

It is the pump that is responsible for the pressure; if the pump stops, the pressure indicator will drop to zero. THIS CANNOT BE ALLOWED! Because the engine will not be lubricated at all, which will lead to instant breakdown, especially at high speeds.

BUT often the oil pump does not stop, but simply begins to pump worse, this indicates its wear, which is why you need to know the oil pressure in the engine! To respond in time to the nearest oil pump failure.

Rotary

The design of this type of unit is a little more complicated. The device consists of two rotors - driven and driven. Both are enclosed in a housing.

If the pump is unregulated, then the oil that is sucked into the device passes through the rotor blades. If the pressure level in the system is higher than the nominal or calculated pressure, then the pressure reducing valve is activated to relieve excess pressure.

Adjustable devices have a special movable stator equipped with a spring. It regulates and ensures constant oil pressure regardless of the engine speed. The stator is designed to control constant pressure by varying the volume of the cavity between the rotors. To do this, the stator is rotated in the required direction.

Removal

Begin:

• First of all, disconnect the “-“ (minus) wire from the battery, as with any other repair.
• Drain the oil (through the plug on the oil pan) from the engine
• We take out the camshaft drive belt

• We take out the crankshaft toothed pulley, then its key, using two flat-head screwdrivers.
• Now remove the oil pan
• Unscrew the oil intake fastener

Unscrew the oil intake fasteners and remove it

Using a 10mm socket with an extension and a ratchet, unscrew the six bolts securing the oil pump to the cylinder block.

Unscrew the mounting bolts using a ratchet socket

Remove the unit from the engine.

Be sure to wash the new oil pump with gasoline to wash off the preservation lubricant. We fill it with oil before installation so that it does not rotate dry when starting. It is also important to rotate the drive gear to install the pump on the crankshaft: so that the protrusions on the gear coincide with the groove on the crankshaft. Lubricate the edge of the oil seal before putting the pump back. Carefully tuck the working edge of the oil seal onto the shaft journal using a wooden stick. When tightening the bolts, be careful and careful. so as not to strip the thread. Install the remaining parts in reverse order.

Disassembly

So:

We clamp the pump body in a vice, placing soft pads on the jaws and, using a 8-mm hexagon, unscrew the bypass valve plug.

Unscrew the valve plug

• We remove the piston and spring of the bypass valve.
• We check the seat of the bypass valve - the presence of burrs and scratches is unacceptable
• Using a 5mm hexagon, unscrew the six bolts securing the pump housing to its cover.

Unscrew the bolts securing the housing to the cover

• We take out the pump housing.
• We take out its drive gear from the cover.
• Behind it, we remove the driven gear.
• We wash all pump parts with gasoline, diesel fuel or kerosene, wipe the gears dry, and lubricate them with clean oil before installing them back.
• We carefully inspect the body for cracks, chips, and severe burrs, and if found, replace it.

Permissible seat diameter and permissible partition thickness

• The same goes for pump gears; scuffing, chips, and cracks are not acceptable.
• We check the condition of the pressure reducing valve spring; if it is broken, cracked, or very short (compressed and does not match the dimensions), we replace it.

Acceptable dimensions of the pressure reducing valve spring

Assembly

We assemble the pump in the reverse order of disassembly. The driven gear inside the pump is positioned so that its side with chamfers and a mark is attached to the housing.

The mark with which the driven gear is applied to the housing

The same with the drive gear. That's all. The pump assembly is completed, all that remains is to install it in place, as our instructions say. In addition to the instructions, we recommend watching a video on this issue.

Max

The first problem we encountered after purchasing a used VAZ 2112 car was that the timing belt broke and all the valves were bent. The repair cost more than 15 thousand rubles. After buying a car, be sure to go to a car service center, check everything and repair it, otherwise the repair may cost a pretty penny like it did for me. And so the VAZ car is not whimsical in maintenance. I do everything myself and rarely call for service.

your name

Timing and alternator belts are usually changed immediately upon purchase. The same as liquids (antifreeze, brake fluid, oil).

VAZ 2109: oil pump and its malfunctions When you need to replace the oil pump in a VAZ 2104 Replacing the VAZ oil pump yourself Repair and replacement of the VAZ 2110 oil pump

Dismantling

Repair of the fuel pump on carburetor VAZ 2108, VAZ 2109, VAZ 21099

Removing the pump yourself is not difficult. Yes, and you are quite capable of performing independent repairs.

To repair, assess the condition of the pump, check the performance and degree of wear of its individual elements, you first need to remove the device and disassemble it.

1. De-energize the car by removing the negative terminal from the battery.
2. Loosen the generator mounting bolts and remove the belt.
3. Prepare a clean container by draining the oil from the crankcase into it. Next, you will need to remove the engine protection and oil pan.
4. Remove the camshaft drive timing belt.
5. Now that the belt is removed, do not turn the crankshaft or camshaft under any circumstances. Otherwise you will damage the valves by hitting them with the pistons.
6. Remove the crankshaft pulley by using two flat head screwdrivers and pulling it off the shaft. If the key does not hold well in its seat, it is better to remove it too.
7. Next in line for dismantling is the oil receiver. To remove it, you need to unscrew the two fastening bolts located on the main bearing cover, as well as one fastening bolt connecting the oil receiver to the pump (oil).
8. Remove the pump, held in place by six bolts.
9. After unscrewing all the bolts, carefully slide the oil pump away from the main bearing cap, then remove the oil pump with peace of mind.

Dismantling the device

Replacing the oil receiver of a VAZ 2112

In this article we will continue assembling VAZ-2112 engine components.

Lubricate the sealing ring of the oil receiver with engine oil

It is advisable to replace the oil receiver O-ring

We install the oil receiver in place and tighten the bolt securing the oil receiver to the oil pump with a torque of 7.0-8.0 Nm (0.7-0.8 kgf m).

We tighten the two bolts securing the oil receiver to the cover of the second main bearing with a torque of 8-10 Nm (0.8-1.0 kgf m)

Cut off the protruding ends of the oil seal holder gaskets.

Lubricate the plane of the cylinder block with grease

Installing the oil pan gasket

If the pan is slightly deformed, it is better to coat the pan gasket with sealant.

We tighten the oil sump mounting bolts with a torque of 5-8 Nm (0.5-0.8 kgf m).

Install the key into the groove of the crankshaft

Installing the crankshaft timing belt

We put the timing belt on the crankshaft pulley

Install the washer on the belt drive pulley

We put on the generator drive pulley and attach the bolt and washer

We tighten the pulley mounting bolt, holding the flywheel on the other side with a torque of 97.9 - 108.8 Nm (9.90 -11.1 kgf.m)

We install the sealing gasket on the water pump and lubricate the gasket with grease.

Install the water pump into the cylinder block so that the factory marking of the pump is directed towards the mating plane of the cylinder block, since the mounting bolts are located asymmetrically.

Tighten the coolant pump mounting bolts to a torque of 7.64–8.01 Nm (0.78–0.82 kgf.m)

After this, install the cylinder head as indicated in the article - “Removing and installing the cylinder head.”

Running in the engine after assembly

The repaired engine is subjected to bench testing (run-in) without load according to the following cycle: 750–800 min -1. 2 minutes

1000 min -1 . 3 min

1500 min -1 . 4 min

2000 min -1 . 5 minutes

After installing it on the stand and starting the engine, check:

– whether there is a leak of coolant or fuel between mating parts and in pipeline connections; – oil pressure and whether there is any oil leakage through the gaskets;

If any unusual knocking or malfunctions are detected, stop the engine, eliminate them, and then continue testing.

If oil leaks through the gasket between the crankcase and the cylinder block, tighten the fastening bolts to the recommended torque.

If the oil leak continues, check the gasket and replace it if necessary.

If oil leaks through the gasket between the cover and the cylinder head, check the gasket and rubber bushings on the studs securing the cylinder head cover.

If necessary, replace the gasket and bushings, following the recommendations outlined in the article “Engine Assembly”.

After engine repair, a certain period of running-in of the working surfaces of new parts is necessary.

This especially applies to those engines on which the pistons, connecting rod and main bearing shells have been replaced, the crankshaft journals have been ground, and the cylinders have been honed.

Therefore, when running in a repaired engine, do not subject it to maximum loads.

Engine break-in should continue with the vehicle at the recommended speeds for the vehicle's break-in period.

Malfunctions: causes, elimination

The 2112 motor has the following weaknesses in its design:

It is very difficult to independently determine the cause of internal combustion engine vibrations, since special equipment is required.

Oil pump installation

1. 1. Before installing a newly purchased VAZ 2112 or 2110 oil pump, be sure to lubricate its pressure reducing valve and gears. Also, when replacing, use only a new oil seal;
2. 2. Install the oil pump, place the timing belt on the tension rollers, and align it according to the marks. Next, the plastic protection is installed.;
3. 3. Put on the wheel;
4. 4. Install the oil intake on the oil pump VAZ 2112, 2110;
5. 5. Thoroughly degrease the crankcase and apply sealant;
6. 6. Install a new gasket, then apply sealant again;
7. 7. Degrease the block, install the crankcase in its place. The task will be simplified if you first screw a few bolts in different places and then tighten the rest;
8. 8. The flywheel protection is installed, followed by the crankcase protection (if available);
9. 9. Fill with high-quality oil and start the VAZ 2110, 2112 engine.

Repair of pump VAZ 2112, other models

You can also repair the VAZ 2110 oil pump with your own hands, which consists of disassembling this product, visual inspection to identify worn parts, followed by replacement. But it is the best option only if there are spare parts or another serviceable unit. In all other situations, it would be more practical to purchase a new product for the VAZ 2110, 2112.

DIY pump repair VAZ 2110/2112

The driver does not always have the opportunity to replace a faulty pump. In some cases, it is possible to repair the device by restoring the operating functions of the pump. If the pump has not yet exhausted its service life (50 thousand kilometers), then you can repair it. However, the pump cannot be repaired without using a special repair kit. This is a set of rubber gaskets and parts that most often fail and need to be replaced.

Repair kits for pumps may vary in composition, depending on which spare parts need to be replaced

In addition, you will have to thoroughly prepare for repairs: the place for disassembling and repairing the pump must be clean and level.

How to disassemble a water pump

Once the pump is removed from the machine, it will need to be disassembled. Only after disassembly and thorough cleaning will it be possible to replace the leaked parts of the pump.

To disassemble the pump, it is recommended to follow the following diagram:

1. Wipe the product with a dry cloth.
2. Unscrew the pump pulley.
3. Pull out the thrust ring.
4. Use a hammer to knock out the bearings from the shaft.
5. Pull the shaft itself out of the housing.
6. Unfasten the impeller.
7. If something remains from the oil seal, then remove the remaining rubber from the housing.

The procedure for disassembling the water pump is intuitive: until you remove the pulley, it is impossible to get to the shaft and impeller

After this, the cavity of the pump itself must be thoroughly cleaned of dirt and old deposits - you can wash the pump with the same gasoline that is usually filled into the VAZ 2110/2112 tank.