Engine 21083 (1.5 liter 69 hp)

Dismantling and assembling the piston with connecting rod VAZ 2108, VAZ 2109, VAZ 21099, Lada Samara

Piston with connecting rod:
1 –

connecting rod bolt nut
2 –
connecting rod bearings
3 –
connecting rod
4 –
piston pin
5 –
upper compression ring
6 –
lower compression ring groove
7 –
oil scraper ring groove
8 –
piston
9 –
connecting rod bolt
10 –
connecting rod cap

For the convenience of selecting pistons by cylinder, cylinders and pistons, depending on the diameter, are divided into five size groups: A, B, C, D, E. Pistons of nominal sizes of three classes are supplied as spare parts: A, C, E and two repair sizes. The first repair size is increased by 0.4 mm, the second - by 0.8 mm. By weight, pistons are divided into three groups: normal, increased by 5 g and decreased by 5 g. Pistons of the same group must be installed on the engine. For repair size pistons, repair size rings increased by 0.4 mm and 0.8 mm are supplied as spare parts. The number “40” is stamped on the rings of the first repair size, and “80” on the second.

Nominal sizes of cylinders and pistons

Engine model VAZ-2108

Engine model VAZ-21083

Cylinder diameter, mm

Piston diameter, mm

Cylinder diameter, mm

Piston diameter, mm

To select pistons for cylinders, calculate the gap between them. The gap is defined as the difference between the measured diameters of the piston and cylinder of VAZ 2108, VAZ 2109, VAZ 21099. The nominal gap is 0.025-0.045 mm, the maximum permissible is 0.15 mm. If the gap does not exceed 0.15 mm, you can select pistons from subsequent classes so that the gap is as close as possible to the nominal one. If the gap exceeds 0.15 mm, bore the cylinders to the next repair size and install pistons of the corresponding repair size.

EXECUTION ORDER
1. We recommend removing the piston rings with a special puller. If it is not there, carefully push the ring lock apart and remove the ring from the piston. Remove the remaining rings in the same way.	2. Using a special mandrel, press the pin out of the connecting rod.	3 . Inspect the pistons. If they have burrs, burn marks, or deep scratches, replace the pistons.
4. To determine the clearance, measure the cylinder diameter and the piston diameter, which is measured with a micrometer in a plane perpendicular to the piston pin axis, at a distance of 51.5 mm from the piston bottom.	5. Use a feeler gauge to measure the gap between the rings and grooves on the piston in several places around the perimeter. If the clearance exceeds the maximum permissible (see Note 1), replace the Lada Samara pistons with rings.	6. Insert the piston ring into a special mandrel and measure the gap in the lock. Instead of a mandrel, you can insert the ring into the cylinder and push it with a piston so that the ring fits without distortion. If the gap exceeds the maximum permissible, replace the ring (see note 2). If the gap is less than 0.25 mm, carefully file the ends of the ring with a file.

Gap between rings and piston grooves, mm

Decarbonization of piston rings

If the engine starts to smoke, there is a possibility that there are rings stuck in the piston grooves. Nowadays, there are many different modern means for decarbonizing piston rings, and many drivers use them to restore engine performance. Among the most popular compositions are:

Motorists believe that if the engine starts smoking, you need to use a decarbonizer, and the engine will work as before, without oil consumption and without smoke. Indeed, sometimes these remedies help, but only in cases where the motor has stood motionless for a long time (for example, after winter), and moisture has accumulated in it. If the car is subject to long-term preservation (put in a garage for winter storage), you should remove the spark plugs and pour oil into the cylinders, and plug the spark plug holes with plugs. With such prevention, the spark plugs will not become damp and rust will not accumulate on the sleeves.

But if, after all, a forgetful car owner has not taken preventive measures, you can use a decarbonizer. We get rid of rust in cylinders as follows:

pull off high-voltage wires;
unscrew all spark plugs;
rotate the crankshaft so that all pistons are in the middle position;
pour 45 ml of liquid into each cylinder, install spark plugs; leave the cylinders to “soak” for 6-7 hours;
why do we turn out the spark plugs, turn the starter a few revolutions so that all the dirt flies out of the engine;
We put the removed parts back in place and start the engine. At first it may smoke a lot, but then the smoke will go away.

Car owners should remember that decarbonization is not a panacea for all ills, and if the piston rings are worn out, then only replacing them will help.

If you find an error, please select a piece of text and press Ctrl+Enter.

Calculation of VAZ engine volume, selection of crankshaft

Engine Connecting Rod – Conrod

Connecting rod length	Neck diameter	Piston pin	Finger fit type	Name
121	47,8	22	pressing *	2108 “standard”
121	47,8	22	floating	2110-12 “standard”
126,4	47,8	22	floating	2110 tuning
129	41,5	19	floating	21128 “standard” – original inserts 21128
129	47,8	22	pressing	2101 tuning
129,2	47,8	22	floating	2110 tuning
129,2	47,8	20	floating	2110 tuning
131	47,8	19	floating	2110 tuning
133	47,8	19	floating	2110 tuning (STI 217.02)
133	47,8	19	floating	2110 tuning (STI 216.55, H-shaped)
135,1	47,8	19	floating	2110 tuning (STI 216.50, H-shaped)
136	47,8	22	pressing	2101 “standard” , until 1982 they were produced with an oil nozzle
136	47,8	22	floating	21213 “standard”

Crankshafts – Crankshafts – Cranks

Piston stroke	crank radius	Crankshaft name
66	33	66 * 2101 “standard”
80	40	80 * 2103 “standard”
80	40	80 * 21213 “standard” – full counterweight
84	42	86*tuning
86	43	86*tuning
88	44	88*tuning
90	45	90 * tuning (crankpin 43mm)

60,6	30,3	60.6 * 2108 “standard”
71	35,5	* 21083-12 f”standard”
74,8	37,4	* tuning
74,8	37,4	74.8 * tuning (STI 116.50, full counterweight)
75,6	37,8	11183 “standard”
78	39	78 * tuning
79	39,5	79*tuning
80	40	80*tuning
80	40	80 * tuning (STI 218.00)
83	41,5	83 * tuning (STI, on order)
84	42	84 * tuning (STI, on order)
84	42	84 * 21128 factory stock (STI 218.00, for connecting rods 21128 and bearings 21128)
86	43	86*tuning
88	44	88 * tuning (crankpin 45mm)

Cylinder Blocks

Block height is the distance between the geometric center of the crankshaft and the top plane of the cylinder block.

Height mm.	cylinder diameter	Name
207,1	76	Block 2101 cylinder diameter 76mm
207,1	79	Block 21011 cylinder diameter 79mm
215,9	76	Block 2103 cylinder diameter 76mm
215,9	79	Block 2106 cylinder diameter 79mm
214,58	82	Cylinder block 21213
194,8	76	Block 2108 cylinder diameter 76mm
194,8	82	Block 21083 cylinder diameter 82mm
194,8	82	Block 2112 cylinder diameter 82mm
197,1	82	Block 21124 cylinder diameter 82mm
197,1	82	Cylinder block 2108-2112 Kalina (+2.3mm)
198,3	82	Cylinder block 2108-2112 (+3.5mm)
199,3	82	Cylinder block 2108-2112 (+4.5mm)
199,5	82	Cylinder block 2108-2112 (+4.7mm)

Classic configuration options

Engine	2103	2106	21213	1900cc	2000cc	2000cc	1800cc
Piston stroke:	80	80	80	84	88	90	84
76	79	82	84	84	84	82,4
Volume cm cube.	1450	1567	1690	1861	1950	1994	1790

VAZ piston shortfall 1.6 mm - the distance between the piston at the top dead center and the plane of the cylinder block.

The volume of the VAZ classic combustion chamber is 33.2 mm2.

Pistons by model:

General characteristics of VAZ pistons
Drawing Type of pistons	Models Full number of models presented

[/td]

Modifications The full number of all VAZ modifications presented in our database(drawing)33 units 196 units

Piston stroke for major modifications
Modification Car modification

The data is presented for cars of different modifications and years of manufacture.

Caution: The above data are the official figures of the manufacturer, but please note that the information is for reference only and does not guarantee specific accuracy.

Source: razmery.info

Dimensions of connecting rod VAZ 2108

This product was chosen by 6 customers

The connecting rod length is standard – 121 mm.

The approximate weight of each connecting rod is 600 g.

The weight of the standard connecting rod is 701 g.

Lightweight connecting rods are used to reduce inertial masses.

Lightweight connecting rods of the VAZ 2110 FOR-MASH allow you to achieve higher engine speeds for a long time. Lightening the connecting rods increases the torque of the internal combustion engine, reduces mechanical losses, reduces fuel consumption, and increases the dynamics of vehicle acceleration. Lightening the connecting rod , especially the upper head, reduces lateral pressure on the piston. The connecting rods are balanced on a special device that allows you to hang the connecting rods so that the center of mass for all is at the same point. The residual tension of the connecting rod on the taur leg has been removed, which ensures its reliability. Each set is weighed.

Weight, kg: 2.4 Dimensions, cm: 21 x 15 x 10 Volume, m3: 0.00315

Design solutions

Features of the internal combustion engine of the base model 2108 are:

the length of the valves and connecting rods has been reduced - making it possible to reduce the dimensions of the internal combustion engine and the noise from its operation;
the oil pump is shifted to the crankshaft end - to reduce the size of the unit;
efficiency
The shape of the combustion chamber is copied from Porsche engines.

When designing the engines, it was planned to carry out a major overhaul after 120 thousand kilometers. In practice, the resource turned out to be twice as high.

Product delivery options

Note! Below are the shipping methods available specifically for this product. Payment options may vary depending on the shipping method. Detailed information can be found on the “Delivery and Payment” page.