Kalina fan switch sensor: where is it located, how to check

Owners of popular Lada Kalina models often encounter situations when the cooling fan does not turn on. This situation forces the driver to periodically stop to allow the engine to cool down. If a malfunction occurs in frosty weather, then it has almost no effect on the functionality of the system, but in warm periods it significantly prevents the LADA Kalina from moving smoothly.

Most Lada Kalina owners are not able to independently diagnose the reasons why the cooling fan does not turn on, much less eliminate them. Tow trucks and services, as well as a switching diagram, are happy to come to their aid.

List of contact relays

If we open the main fuse box of Kalina 2, we will see a set of electrical relay housings. There are no other blocks containing relays in the car. We list the elements used in the “Lux” package (21927/21947):

K1: radiator fan relay;
K2: relay switching on door locks;
K3: additional starter relay;
K4: additional relay (switches current 50A);
K6: wiper relay;
K7: relay that turns on the high beam;
K8: signal relay;
K9: relay that turns on the low beam;
K10: rear window heater relay;
K11: main ignition relay;
K12: relay turning on the fuel pump;
K13: additional relay;
K14: radiator fan relay 3;
K15: windshield heater relay 1;
K16: windshield heater relay 2;
K17: relay that turns on the air conditioning compressor.

You can compare the layout of elements in “Lux” and in “Norm/Standard”:

Let's consider the data relevant for the “Normal/Standard” configurations:

K1-K12: as above;
K13: radiator fan relay 3;
K14: windshield heater relay 1;
K15: windshield heater relay 2;
K16: air conditioning compressor relay.

The last list is also relevant for Kalina Cross Norma. And in more expensive trim levels of the crossover, the “Lux” scheme will probably be used.

Checking and replacing the Kalina cooling fan resistor

Removing the additional fan resistor is done as follows:

put the car on the “handbrake”;
open the hood;
remove the ground wire from the battery;
remove the engine splash guard;
unscrew and remove the engine crankcase protection (if installed);
press the block latch and unplug the electric fan power supply wiring harness;
Using a Phillips screwdriver, unscrew the two screws holding the additional resistor;
move aside the resistor mounting bracket together with the block;
pull out the resistor.

Checking the resistor consists of two stages:

visual inspection of the integrity of the spiral;
checking the resistor winding for open circuit using an ohmmeter.

If a winding malfunction is detected, the resistor must be replaced with a new one. If the thermal fuse is faulty, then all you can do is replace it. To do this, you will need a soldering iron to remove the burnt fuse and solder a new one in its place. All that remains is to put the parts in their original places. Installation of the Kalina cooling fan resistor is carried out strictly in the reverse order of removal.

Tips for motorists

The radiator fan of the engine cooling system of the Lada Kalina passenger car should turn on automatically when the coolant temperature reaches more than 95 degrees. And if this does not happen, then the engine begins to overheat and the driver’s failure to take timely measures to reduce the temperature (switching to idle speed) leads to jamming of the pistons in the engine cylinders.

to start troubleshooting a fan failure by checking the integrity of the fuse that protects this electrical circuit. It is located on the side of the console near the front passenger's feet. To get to it, you need to unscrew one screw securing the cover with deflectors designed to supply warm air to the passenger’s feet.

But you can remove the additional fuse and relay block only after you unscrew the bolt securing it, for which you will need a 10mm wrench. You need to take it out carefully and slowly so as not to damage it, since the bundle of wires suitable for it is very in the way . There is only one fuse in the block, exactly the one you need.

If the fuse is intact, then you can immediately check the serviceability of the relays through which voltage is supplied to the fan motor. There are two of these relays: the leftmost one above the mounting bar is designed to turn on a low fan speed, and the rightmost one is designed to turn on a high fan speed.

Another malfunction associated with the fan relay is that the fan continues to operate after the ignition is turned off, and if you leave the car in the parking lot without paying attention to it, the battery will discharge, which will lead to problems with starting the Kalina engine. Sticking of the relay contacts occurs due to antifreeze entering this block as a result of its leakage from the heater radiator.

If everything is in order with the fuse and relay, then you will have to open the hood and check the serviceability of the temperature sensor, which commands the fan to turn on. It is located on the right radiator tank. To check its functionality, simply remove the plug connector from it and close the connector terminals with a jumper. If the fan starts working, then the sensor is working, and if it doesn’t work, then before drawing a conclusion that the sensor is faulty, you need to check the serviceability of the fan motor itself. To do this, you will need to connect the motor terminals directly to the battery terminals.

Removing the fan sensor

DVV is a non-separable product and cannot be repaired. However, to ensure that it is fully operational, it must be removed from the vehicle. To do this proceed as follows:

The car is placed on level ground with the handbrake lever raised.
Start working after the engine has completely cooled down, removing the terminals from the battery.
Having squeezed out the plastic clip, remove the chip with the cable from the DVV glass.
Remove the plug from the expansion tank, otherwise when the sensor is removed, a small amount of antifreeze will splash out.
Use a spanner wrench or a 19 DVV socket to unscrew it from the seat. If the thread does not lend itself well, then apply WD 40 lubricant under the sensor nut (you can buy it at any auto store or gas station).

Removing the chip from the sensor:

Step-by-step instructions for replacing the coolant temperature sensor on a Priora

If for some reason you cannot contact specialists for service, then you can do the work yourself.

Allow the power plant to cool to an acceptable temperature.
Prepare any rags.
Remove the housing from the air filter. A shaped screwdriver will come in handy in this case.
Carefully loosen the clamp and remove the air duct.
At this stage, disconnect the harness and remove the rubber pads directly from the body.
Remove the connector from the sensor.
Now place the prepared rags on the clutch cover and under it.
As quickly as possible, using a key set to “19”, unscrew the broken sensor and install a new one. Tighten everything as best as possible.
Do not unscrew the coolant reservoir cap before the replacement procedure. In this case, losses of OX will be minimal.
Now you can put everything back together in reverse order.
Check the coolant level.
Start the engine.
When the fan works and everything works as expected, without interruptions or leaks, the work is considered completely completed.

We invite you to watch the video on replacing the sensor on a Priora.

How to find the reason

Let's start by checking the electric motor. Disconnect the electrical wires and connect directly to the battery, observing the polarity. If the fan doesn't start, that's the problem. If it works, you need to look for another reason.

Check all contacts on the connectors, as well as behind the relay and fuse. They are located in an additional mounting block, which is located on the right side of the instrument panel next to the lower heater duct.

The fuse (50A) can be checked with a tester; it is better to take a working relay and install it in the appropriate socket. If the problem is not resolved, continue.

Check temperature sensor. Warm up the engine to operating temperature, stop the engine and disconnect the sensor. It is located on the top of the thermostat housing. When the sensor is disabled, the controller must independently start the fan for continuous operation.

Start the engine and wait until the fan starts. If the coolant temperature has reached a critical temperature and the fan does not turn on, look for a broken wiring.

Do I need to change the fan?

If you determine that the problem is in the fan itself, or more precisely in its motor, you can try to fix it. Most often it stops working due to broken brushes or problems with the rotor bearings. The commutator or winding crack is rarely damaged.

If the fan cannot be repaired, it must be replaced.

Under no circumstances should you drive a vehicle with the fan not working. Overheating of the engine inevitably leads to the destruction of rubber hoses of the cooling system, seals, and can also cause failure of the piston group elements.

How to check the sensor yourself?

Checking the fan switch sensor is not difficult.

If there is a need to diagnose it, you must first find out its functions and operating principle.
After this, you can test the system by heating the most vulnerable part of the sensor housing. To do this, you need to remove it from the radiator, carefully inspect it, check the contact pads, inspect the wires, and, if necessary, clean it.
Next, you will need a tool that you can make yourself from a regular light bulb and battery, or use a special tester.
Bring water to a boil, then connect the tester and sensor contacts and lower its vulnerable side into the water.
After this, a short circuit should occur. This action will cause the lamp to ignite, or the characteristic sound signal of the tester to appear. If the device shows that the contacts closed before colliding with boiling water, then the sensor is undoubtedly faulty. The author of the video, Mechanical Technician, will tell you how to check the fan switch sensor.

Installing a new fan sensor

After dismantling the old device, a new DVV is installed:

The sensor is inserted into the mounting socket, having previously lubricated the threads of the device skirt with oil.
Screw in the meter with a spanner wrench or a 19mm socket without applying excessive force.
The cable block is inserted into the glass of the new sensor.
After unscrewing the radiator cap, pour antifreeze into its neck until the fluid level in the expansion tank is between o and “Max”.
The radiator cap and expansion tank plug are returned to their place.
Start the engine and wait until the arrow on the instrument panel approaches the red zone. If the fan turns on at this moment, this means that the repair was completed correctly.

Experts advise purchasing a new coolant temperature sensor only from a brand model. Savings when buying a cheap product can result in exorbitant financial costs for engine overhauls.

At the first overheating of the Kalina engine, you need to stop and stop driving to allow the engine to cool. If the problem is a breakdown of the engine, then you need to get home, making stops and watching the coolant temperature arrow along the way. To avoid this, remove the fan motor cable and directly connect the fan with additional wires to the battery. This way you can return to the garage without letting the coolant boil.

Repair or replacement

If the reason for the impeller not rotating is the electric fan, you can try to repair it. Often, repairs come down to replacing the brushes and bearings of the electric motor. But if a short circuit occurs in the stator or rotor windings, repair is impractical and the unit will have to be replaced. There is nothing else to break in the electric fan, since the design is simple.

If forced cooling does not work, the vehicle cannot be operated. Overheating of the coolant is dangerous for all components of the power unit. The rubber connecting hoses and cylinder head gasket begin to deteriorate and the valves burn out. Ultimately, extremely high temperatures will cause the pistons to expand and the cylinders to scuff, meaning a major engine overhaul will be required.

Video “How to properly replace the thermostat on a Lada Kalina?”

If the problem of a non-functioning sensor in a Lada Kalina car lies in the failure of the thermostat, then this unit will also need to be replaced; detailed instructions for replacing it at home are presented below (the author of the video is Alexey Golubkov).

Why doesn't the cooling fan turn on on Kalina? Several reasons to choose from

Within the city limits this is not so serious: if you are in a hurry, you can leave the car and get where you need to go by public transport in order to deal with the cooling system later. But between cities, a non-working fan is a great headache. If you don’t find the cause and don’t eliminate it, it can take 8 hours to drive 40 kilometers without a tow: you drive 2-3 km, then you stop and wait for it to cool down. It's going to be a fun trip! Especially if there are tired children behind you who were planning to quickly get there and start resting.

Why doesn't the cooling fan turn on on Kalina?

There are several reasons for this. Some can be fixed on site, while others will require additional spare parts. But even if you can’t start the fan right away, you can at least assess the prospects and start waving the cable as it passes a couple of hours earlier, while you still have the strength to do something.

Before checking the remaining components of the cooling system, you need to make sure that the worst has not happened to you, and. I must say that in Kalina this is an extremely unreliable unit and for some reason it breaks down often and frequently. There are cases when it stopped working, even if it was changed the day before yesterday. Therefore, many experienced owners of this car, when going on a long trip, take a spare one with them. Yes, just in case!

You can make sure that the thermostat is normal (or not) by touching the lower radiator pipe. If it remains cold, it means that the thermostat is no longer alive, and you need to get a backup one or ask for a tow. In the absence of both fellow travelers and supplies, you will have to crawl slowly and sadly to the nearest service station.

Having excluded the thermostat from the list of probabilities, we check the electrical circuit. First - fuses

(how to check them correctly,).

The first is the one that is directly responsible for the electric fan. It is located on the side of the console, where the front passenger's feet are. It’s not difficult to get to it: unscrew the screw that secures the cover with deflectors for blowing warm air - and in front of you is the required spare part.

If this fuse is intact

, you will have to climb further into the additional block. Use a ten key to unscrew the fastening bolt and pull out the entire assembly. At this stage, you need to be patient and careful: extraction is significantly hampered by a whole bunch of wires going to the block. If you pull one out, you will be stuck on the highway for a long time. But it doesn’t take long to look for a fuse in the block: there is only one there, exactly the one you need.

If this part is normal, we immediately check the relays - they are located in the same block and transmit voltage to the fan motor. There are 2 of them: located above the mounting strip on the left edge is responsible for the operation of the fan at low speeds, the one on the far right turns on its high speed. Both must be in working order.

If no faults are found here, you will have to crawl under the hood.

You need to check both it and the temperature sensor. Let's take a look at the electric fan first. To ensure that the engine is working, its terminals are connected directly to the battery. If it starts, it means everything is fine with the fan. Let's move on to the sensor. Depending on what engine is on your iron horse, the actions will be different:

With carburetor:

We remove the plug connector of the temperature sensor (it is located, by the way, on the right radiator tank) and close its terminals with a jumper. The fan started spinning - the sensor is working, the terminals just came off. Left dead - it's time to change the sensor; With injector

We look for the sensor next to the thermostat and remove the connector from it. If the fan starts spinning, it means that the emergency mode has turned on, and your sensor has already burned out.

The main reasons why the radiator cooling fan does not work

Let's look at the main options and places to look for faults:

Thermostat.
If it fails, this is the reason why the cooling fan does not work correctly. To diagnose this malfunction, you should touch the lower pipe. If it is cold, then the thermostat is dead. Many Kalina car owners are accustomed to this phenomenon, since it often breaks down, and they carry a spare one with them.
If it's not the thermostat, then the next step is the fuses. You need to make sure that they are working and all controllers too. The easiest way is to test them using a tester or ohmmeter. The fuse diagram is here.
If the fuse is alive, then you will have to remove the additional fan control unit. To do this, it is worth moving the warm air duct and using a 10 mm wrench to unscrew the fastenings of the unit. Now you can get it freely. It has two relays that are responsible for turning on the fan and for high speeds. Let's diagnose both.
Now, we can move on to the darkest option - we climb under the hood and “ring” the contact wires of the fan itself. Of course, there may be a break or break in the wire, but there is nothing worse than a burnt winding inside the fan. Most likely the fan in this case will need to be replaced.
Another reason for the fan not turning on may be a broken thermostat sensor. In order for the fan to start in emergency mode, you will have to remove the connectors from it. You can check the sensor by removing the thermostat and placing it in a pan of hot water; the thermostat should open.
The last reason why the fan may not work is a break in the switching circuit itself.

Block in the engine compartment

The power fuse box is located in the engine compartment under the hood, near the left strut support. To get to it, you need to open the lid by prying the latch.

1 (30 A) - engine control system circuit . If there are problems with the electronic control unit, short circuits or other malfunctions, this fuse may blow out.

2 (30 A) - vehicle on-board circuit . 3 (40 A) - vehicle on-board circuit .

4 (60 A) - generator circuit.

5 (50 A) - electric power steering circuit.

6 (60 A) - generator circuit.

In case of any problems, it is important not to panic, to think soberly and logically. The most important thing is to diagnose and establish the cause of the breakdown. If you don’t have enough experience or nerves, it’s easier to sign up at the nearest car service center if it has a competent electrician.

I hope this article will help you deal with electrical problems and quickly fix any Priora malfunctions. If you have any experience or information, please leave a comment below, useful information will be added to the article.

Design of the LADA Kalina cooling system

Cooling system: 1 — expansion tank;
2 — radiator outlet hose; 3 - inlet hose; 4 - radiator; 5 — steam exhaust hose; b — radiator supply hose; 7 — electric fan; 8 — electric fan casing; 9 — coolant temperature sensor; 10 — coolant temperature indicator sensor; 11 — throttle assembly; 12 — bracket for the coolant pump pipe; 13 — coolant pump; 14 — coolant pump pipe; 15 — heater radiator supply hose; 16 — heater radiator outlet hose; 17 — exhaust pipe; 18 — coolant pump pipe hose; 19 — thermostat housing Expansion tank. Coolant is poured into the system through the expansion tank. It is made of translucent polyethylene, which allows you to visually monitor the liquid level. To do this, the marks “MAX” and “MIN” are marked on the wall of the tank. In the upper part of the tank there is a pipe for connecting to the radiator steam exhaust hose, in the lower part there is a pipe for connecting to the inlet hose. Expansion tank viburnum

Expansion tank cap with valves. The tightness of the system is ensured by the inlet and outlet valves in the expansion tank cap. The exhaust valve maintains increased (compared to atmospheric) pressure in the system on a hot engine (due to this, the boiling point of the liquid becomes higher, steam losses are reduced}. It begins to open at a pressure of at least 1.1 bar. The intake valve opens when the pressure drops to system relative to atmospheric pressure by 0.03-0.13 bar (on a cooling engine).Expansion tank cap with valves

The coolant pump is a vane, centrifugal type, driven from the crankshaft pulley by a timing belt. The pump housing is aluminum. The roller rotates in a double-row bearing. The bearing is lubricated for its entire service life. The outer ring of the bearing is locked with a screw. A toothed pulley is pressed onto the front end of the roller, and an impeller is pressed onto the rear end. A thrust ring made of a graphite-containing composition is pressed to the end of the impeller, behind which there is an oil seal. The pump housing has a control hole to detect fluid leakage when the pump fails. It is recommended to replace the pump as an assembly. The redistribution of liquid flows is controlled by a thermostat. Coolant pump Kalina

The cooling system consists of two so-called circulation circles:

The movement of liquid through the cooling jacket and radiator forms a large circulation circle.
The movement of liquid through the engine cooling jacket, bypassing the radiator, is a small circle of circulation.

The cooling system also includes a heater radiator and a throttle body heating unit. Liquid circulates through them constantly and does not depend on the position of the thermostat valves.

Thermostat. It has a solid temperature-sensitive element and two valves that redistribute the flow of coolant. On a cold engine, the main thermostat valve blocks the flow of fluid from the radiator and the fluid circulates only in a small circle, bypassing the radiator. At a temperature of (85±2) °C, the thermostat valves begin to move, allowing liquid flow into the radiator and closing the bypass channel. At a temperature of about (100±2) °C, the main valve opens completely and the bypass valve closes. Almost all the fluid circulates in a large circle through the engine radiator. Thermostat viburnum

Coolant temperature sensor. To monitor the coolant temperature, a sensor is screwed into the engine cylinder head, connected to the temperature indicator in the instrument cluster. In the outlet pipe, next to the thermostat housing, there is a coolant temperature sensor that provides information to the controller. Coolant temperature sensor viburnum

The heater radiator is built into the engine cooling system and is designed to heat the passenger compartment by circulating hot coolant through it.

The radiator consists of two vertical plastic tanks (the left one is with

baffle) and two horizontal rows of round aluminum tubes passing through the cooling plates. The tubes are connected to the tanks through a rubber gasket. The liquid is supplied through the upper pipe and discharged through the lower. Next to the inlet pipe there is a thin pipe for the steam removal hose. The radiator has a casing with an electric fan. There is a drain plug at the bottom of the right tank. radiator viburnum The fan maintains the thermal operating mode of the engine and is switched on via a relay based on a signal from the controller.

Modernization of Kalina SOD

The main problem of the Kalina cooling system is the formation of air locks. Today there are a number of effective ways to eliminate this defect. The reason lies in the design features of the SOD. The operation of the cooling system is based on the interconnected functioning of many parts. The use of the large and small circuits depends on the temperature of the antifreeze circulating through the system. The normal operation of the entire power plant depends on this.

You can modify the cooling system yourself or at a service center. Professionals rarely engage in all sorts of modifications, recommending replacing or repairing a particular component. This method may be more expensive, but not always more effective.

Classic ways of improvement

In order to solve the problem with the formation of air locks, you need to remove the expansion tank cap and start the engine. Then wait until the coolant temperature rises to the critical red zone until forced cooling by the fan comes into operation. After this, you need to press the gas pedal several times and turn off the engine.

If the method is ineffective, there is another method. To do this, you need to dismantle the engine protection, loosen the clamp and remove one of the tubes of the throttle body heating fitting. Then unscrew the cap of the expansion tank and, applying a rag, start blowing into it until antifreeze begins to flow from the removed pipe. In order to modify the standard cooling system, many car owners install a more efficient 6-hole thermostat, install a coolant filter and another heater faucet.

To increase circulation efficiency, an additional pump is often installed.

Other upgrade options

If the car is equipped with an electronic gas pedal, the hose that previously went to heat the throttle assembly is now looped into the cooling system. To prevent the formation of air pockets, an additional pipe with a smaller diameter is used, which is installed instead of the above hose. The hose for the air duct is placed near the thermostat; for this, a tee is used, mounted in the pipe fitting to the radiator. The second end of the pipe is connected to the steam removal hose near the expansion tank (you will need another tee).

The modification ensures a stable operating temperature of 90 degrees in urban conditions, and the stove begins to warm up at 50 degrees.

The next improvement method is to equip the steam outlet with a special hydraulic fence. To do this, a tube from a dropper is mounted in the steam removal hose, which is immersed in antifreeze at the bottom of the expansion tank. As it cools, the antifreeze is drawn into the outlet pipe, which prevents air from the cooling system. If desired, you can combine both methods.

Forced fan activation

One of the shortcomings of the cooling system of the Lada Kalina is the late activation of the electric fan. Any car owner, even with minimal car repair and maintenance skills, can solve this problem if desired. On most internal combustion engines, the operating temperature should be maintained at 90-95 degrees. On Kalina, the forced cooling fan turns on at a temperature of 100 or 105 degrees. That is, intensive cooling begins at the moment when the engine has already begun to overheat, and this negatively affects the service life of the power unit. To solve this problem, you can install a button to turn on the fan in the cabin, which, when pressed, starts cooling at any time. To work you will need the following parts:

connection terminals;
4-pin relay with mounting bracket;
contact blocks for connecting the button and relay;
wire with a cross-section of at least 0.75 mm.

Connecting the forced (manual) mode of fan operation is carried out according to the following scheme:

On the button connection block, all unnecessary wires are cut off, leaving only two in the center for illumination and two on the edge for connection.
Now you should connect the relay and button. On the passenger side, the protective trim of the center console is removed; there are several relays there. To find out which one is needed, you should start the engine and disconnect the wire block one by one from the temperature sensor on the thermostat.
In this case, the fan should work; now you need to disconnect the relay. If after disconnecting one or another relay the fan stops, then this relay is responsible for turning on forced cooling. If the car stalls when the relay is removed, it means that it is responsible for the fuel pump; you should replace it and start the engine again.
Now you should find the pink and white wires, strip their ends and twist them together, the connection is insulated.
The relay wires are connected to the prepared wire block. White - to contact 87, pink - to 85, contact 86 is connected to the power button, contact 30 is assigned to ground. After completing the connection, all that remains is to find a place to secure it, for example, under a dashboard.
All that remains is to connect the button. The two remaining wires are connected to any backlight lamp, which lights up when the ignition is turned on.

The modification allows you to turn on the cooling fan on the Lada Kalina at any time, not only while the engine is running, but also when it is turned off.

Any modernization can be done with your own hands; it is not at all difficult if you follow the step-by-step instructions. For normal operation of the cooling system, all components and elements must work properly. The fan, although simple in design, is important; without it, you can end up with a major engine overhaul. For this reason, you need to carefully monitor the performance of all components and, if malfunctions are identified, fix them immediately.

Main reasons

Coolant temperature sensor malfunction. There are two of them on the Lada Kalina. One provides data to the instrument panel, the second to the car's ECU.
The fuse in the fan circuit has blown.
Motor malfunction.
Lost contact in electrical wiring connectors.

Verification algorithm

Disconnect the connector from the temperature sensor, which is located near the thermostat. When the sensor is disconnected and the ignition is on, the cooling fan should run constantly. If the fan does not turn on, it may be the fan fuse or the fan itself.
The fan relay and fuse box on the Lada Kalina is located under the decorative trim near the left foot of the front passenger. The block consists of three relays, two of which (1 and 3) are responsible for operating the fan at high and low speed. There is a fuse nearby. The fuse is checked visually (the integrity of the fusible link) or with an ohmmeter, which should show zero resistance. The relay can be checked by connecting the device to the terminals of the contact group and applying voltage from the battery to the switching terminals. You should not install a “bug” made of wire instead of a blown fuse. Fires in cars are not uncommon. It is necessary to find the cause of the burnout; perhaps a short circuit in the electric motor or wiring. Install a similar fuse. If everything works fine, then everything is put back in place; if the fuse blows again, then the reason is a short circuit. The fuse rating is 50 A.
The serviceability of the fan itself is checked by applying voltage from the battery directly to its connector. If it rotates and all other elements are working properly, then the only reason is the electrical wiring. Fortunately, this is quite rare. When the engine does not work even when directly connected to the battery, there is only one way out - replacing the fan. Repairing the engine does not make sense, since the cost of a new one is not that high, and the reliability of the repaired one is unlikely to be high.

Sensor check

For a complete check, the sensor will have to be removed, which involves draining a small amount of coolant.

You can check the sensor with a tester in resistance mode. The probes of the device are connected to the connector terminals and the tip of the sensor is immersed in hot water. Table of indications.

Temperature (°C)	Resistance (Ohm)
100	177
90	241
80	332
70	467
60	667
50	973
45	1188
40	1459
35	1802

When checking, you need to check the condition of the connector contacts. If the contact is poor, they will overheat and the contact will weaken even more, until it completely disappears. Connectors must be dry, clean and free from overheating.

Let's sum it up

If a cooling circuit fan in a Lada Kalina fails to operate, then such a malfunction can be corrected independently. We have reviewed almost the entire list of reasons that could cause a malfunction, and also provided an algorithm for replacing the unit. Use our material as instructions for action and tend to periodically inspect the cooling system; a switching diagram can also help you. This will minimize the risk of unpleasant circumstances occurring on the road.

Replacing the cooling fan Lada Kalina

To replace the cooling fan, it is not necessary to go to a service station. You can do this without much difficulty on your own.

Required tools:

head with ratchet or socket wrench 10;
spanner or open-end wrench 8;
screwdriver with Phillips bit;
pliers.

Work order

Place the car on a level surface.
Raise the hood, disconnect the ground wire from the battery.
Using a 10mm wrench, unscrew the two air filter mounting bolts.
Disconnect the mass air flow sensor connector by pressing the latch.
Disconnect the purge valve connector located on the air filter housing.
Using a screwdriver, unscrew the bolt of the air duct fixation clamp and remove the corrugation.
Unscrew the 4 screws securing the air filter cover.
Remove the cover and remove the filter element.
Using a size 8 wrench, unscrew the nut securing the air intake and remove it.
Using a size 10 wrench, unscrew the two nuts securing the fan casing on the right in the direction of travel of the car, and then with a size 8 wrench, unscrew the two nuts on the left.
Disconnect the fan power connector.
Carefully, so as not to damage the radiator fins, remove the fan along with the housing.
Using a 10mm wrench, unscrew the 3 bolts securing the electric motor and remove it from the housing.
Install a new electric motor with impeller in its place.
Screw the casing assembly with the fan to the radiator.
Connect its connector.
Carry out the rest of the installation work in reverse order.

DIY fault repair

We will not talk about solving problems such as failure of fuses or the sensor itself. Everything is so simple here - failed elements are removed from their installation locations and replaced with new ones.

Separately, it is necessary to highlight the replacement of the ventilation unit - read about this below:

So that during the repair process you do not have to dismantle the radiator, do everything carefully, since there is a possibility of damage to other elements.
Open the hood and disconnect the battery. Remove the air filter.
Having done this, you can dismantle the radiator grille.
Next, you will need to unscrew the top mountings of the optics - the right and left lights.
Using a 10mm wrench (it will be more convenient to take a socket wrench), you will need to remove the upper front panel.
After these steps are completed, you will need to disconnect the plugs that are connected to the ventilation unit. Having done this, the wires can be twisted a little.
Next, using a wrench, you will need to unscrew the four screws that secure the device to be replaced. The arrows in the photo indicate the screws that secure the assembly; they will need to be unscrewed.
Only after the unit is freed will it be necessary to dismantle it and replace it with a new one. After removal, just in case, clean the connectors themselves so that in the future you will not be bothered by the problem of poor contact. Further assembly of the system and installation of all elements is carried out in the reverse order.

Vehicle maintenance

A catalog of consumable spare parts required for maintenance is given in Chapter 3b of this manual.

Periodic Maintenance

Timely and regular maintenance of the car in accordance with the technological map (see the service book attached to the car upon sale) can significantly extend the life of the car.

A message appears in the notification center indicating the mileage remaining until the next service. This message appears and remains for 4 seconds each time the ignition switch is turned to position 2.

The display begins to show mileage - 10,000 km. This distance gradually decreases (every 50 km) until zero remains (in this case, service must be performed). After each service the display is reset again to 10,000 km.

Note

Service intervals are based on 50 km intervals, so short journeys may not be shown on the display.

The vehicle must be serviced every 10,000 km or every 6 months (whichever comes first).

Note

If service has not been performed (or the display has not been reset), the distance indicator will remain at that value after reaching zero until reset.

The service center employee must make the appropriate notes, stamp and sign the vehicle’s service book for each maintenance service.

Replacing brake fluid

Brake fluid requires replacement every two years, regardless of the vehicle's mileage.

Note

Replacing brake fluid is included in scheduled maintenance and is paid for.

Coolant replacement

Engine coolant must be replaced every three years, regardless of the vehicle's mileage.

Note

Coolant replacement is included in scheduled maintenance and is paid for.

Monitoring the content of harmful emissions in exhaust gases

This vehicle is equipped with a system to control harmful emissions and fuel vapors. Incorrect engine settings can affect exhaust emissions, engine performance and fuel consumption, and can cause elevated temperatures that damage the catalytic converters and engine.

Attention Please be aware that replacement, modification or counterfeiting of these devices is punishable by law. In addition, outside interference in engine settings is strictly PROHIBITED!

Design, principle of operation

The design of this sensor includes a thermistor - a resistor that changes resistance depending on the temperature surrounding it. This thermistor is placed in a metal case with a thread applied to it. A tail section made of plastic is connected to this body. This part contains contacts for connecting wiring. One contact is positive and it comes from the electronic unit, the second is negative and it is connected to ground.

In order for the thermistor to work, a voltage of 5 V is constantly applied to it. This voltage is supplied to it by the electronic unit through a resistor having a constant resistance. Since the coolant temperature sensor thermistor has a negative temperature coefficient, as the temperature increases, its resistance will decrease, and the voltage supplied to it will also decrease. Based on the drop in this voltage, the electronic unit calculates the engine temperature and also displays its value on the dashboard.

The exact installation location of this temperature sensor differs from car to car, but only slightly. It can be installed in the cylinder head near the thermostat housing, or on the thermostat housing itself. It must be located near the outlet pipe through which the liquid flows into the radiator. It is located near this pipe in order to transmit accurate temperature data.

What is clearance and how important is it?

This value shows the possible deviation of a given series from the specified nominal value. A correctly calculated circuit must take this indicator into account, or appropriate adjustments are made after assembly. As you understand, our friends from the Celestial Empire do not bother themselves with this, which has a positive effect on the cost of their goods.

The result of such a policy was shown in Figure 4; the part works for some time until the limit of its safety margin is reached.

We make a decision by comparing the readings of the multimeter with the nominal value; if the discrepancy goes beyond the error limits, the part definitely needs to be replaced.

Signs of sensor malfunction

This sensor is considered to be very reliable due to its comparative simplicity of design. However, there may be problems with it too. Usually they come down to a violation of the calibration, which leads to a violation of the resistance and, as a result, incorrect operation of the electronic unit, since it performs part of its functions based on the engine temperature.

One of the most obvious signs of failure of this sensor is the failure of the fan to turn on when the temperature exceeds the set value. But this indicator will not be reliable if there are two sensors - the main one, for transmitting the temperature value to the electronic unit, and the additional one, responsible for turning on the fan. In this case, failure to turn on the fan will indicate damage, oxidation of the wiring, or failure of the sensor responsible for its operation.

Problems when paying with bank cards

Sometimes difficulties may arise when paying with Visa/MasterCard bank cards. The most common of them:

There is a restriction on the card for paying for online purchases
A plastic card is not intended for making payments online.
The plastic card is not activated for making payments online.
There are not enough funds on the plastic card.

In order to solve these problems, you need to call or write to the technical support of the bank where you are served. Bank specialists will help you resolve them and make payments.

That's basically it. The entire process of paying for a book in PDF format on car repair on our website takes 1-2 minutes.

General diagram of VAZ-1117, VAZ-1118, VAZ-1119

1 — right headlight; 2 — engine compartment lamp switch; 3 — sound signal, 4 — Lada Kalina starter; 5 - battery; 6 - generator; 7 — windshield wiper electric motor; 8 — left headlight; 9 — power window switch of the right front door (passenger); 10 — power window motor of the right front door; 11 — right front door lock; 12 — connection block to the right front column; 13 — windshield washer motor; 14 — air temperature sensor; 15 — connection block to the injection system wiring harness; 16 — left front door lock; 17 — brake fluid level sensor; 18 — connection block to the left front column; 19 — right front door power window switch (driver); 20 — left front door power window switch; 21 — door lock switch in the switch block; 22 — electric window motor of the right front door; 23 — mounting block; 24 — immobilizer; 25 — power accessories control unit; 26 — instrument cluster; 27 — right side turn signal; 28 — glove compartment lighting lamp ; 29 — glove compartment lamp switch; 30 — brake light switch; 31 — ignition switch; 32 — lighting control module; 33 — steering column switch; 34 — left side direction indicator; 35 — connection block to the right rear column; 36 — rear door lock; 37 — rear window heating switch; 38 — reverse lock switch; 39 — alarm switch; 40 — heater motor switch; 41 - additional resistor; 42 — heater electric motor; 43 — block is connected to the left rear column; 44 — electric fuel pump with fuel level sensor; 45 — reverse lamp switch; 46 — handbrake sensor; 47 — cigarette lighter; 48 — reverse lock; 49 — connection block to the radio device; 50 — backlight lamps for heater control levers; 51 — Kalina illuminator; 52 — control unit for electromechanical power steering; 53 — interior lighting unit; 54 — right rear light; 55 — trunk locking motor; 56 — switch in the trunk lock; 57 — license plate lights; 58 - additional brake signal; 59 — rear window heating element; 60 — trunk lighting; 61 - left rear light

Elements of the instrument panel harness connection diagram

1, 3, 4, 5 — blocks of the tidy wire bundle to the front harness; 2, 8 - the same for the rear “pigtail” of wires; 6, 7, 9, 10 - continuation of the direction to the assembly unit; 11 — power supply for the lighting control device; 12 — set of instruments; 13 — toggle switch for the electric motor of the stove; 14 — power supply to the air supply box; 15 — ignition switch Lada Kalina; 16 — immobilizer block; 17 — block of the dashboard wiring harness to the ignition system wire bundle; 18 — cigarette lighter power supply; 19 — alarm switch; 20 — rear window heating switch; 21 — brake light switch; 22 — alarm light breaker; 23 — adjustment of computer modes; 24 — windshield wiper control; 25 — VAZ horn switch; 26, 27 — heating and ventilation control lighting lamps; 28 — glove box lighting; 29 — power supply to the on/off button in the glove compartment; 30, 31 — pinout for the standard radio; 32 — power supply to the electric motor of the stove; 33 — heater resistor network; 34 - electric amplifier control unit.

Fan switch sensor Kalina 8 valves how to check

List of contact relays

Checking and replacing the Kalina cooling fan resistor

Tips for motorists

Removing the fan sensor

Step-by-step instructions for replacing the coolant temperature sensor on a Priora

How to find the reason

Do I need to change the fan?

How to check the sensor yourself?

Installing a new fan sensor

Repair or replacement

Video “How to properly replace the thermostat on a Lada Kalina?”

see also

Comments 47

The main reasons why the radiator cooling fan does not work

Block in the engine compartment

Design of the LADA Kalina cooling system

Modernization of Kalina SOD

Classic ways of improvement

Other upgrade options

Forced fan activation

Main reasons

Verification algorithm

Sensor check

Let's sum it up

Replacing the cooling fan Lada Kalina

Work order

DIY fault repair

Vehicle maintenance

Periodic Maintenance

Replacing brake fluid

Coolant replacement

Monitoring the content of harmful emissions in exhaust gases

Design, principle of operation

What is clearance and how important is it?

Signs of sensor malfunction

Problems when paying with bank cards

General diagram of VAZ-1117, VAZ-1118, VAZ-1119