Replacing light bulbs on Lada Kalina

Hello everyone, today I want to show you how I changed the headlight bulb on a Lada Kalina car.

In fact, there is nothing complicated about replacing a headlight bulb. Let's say that changing a low beam light bulb is much more problematic. So, let's begin. First you need to open the hood. Then go to the headlight where the bulb burned out. And remove the rubber plug.

Next, we take out the light bulb with the socket and take out the burnt-out light bulb. There is no need to disconnect any wires.

After that, we take a new light bulb of the same size and install it back; if you wish, you can install a diode. I installed it once and, in principle, I did not find any differences, that ordinary lamps burn out and diode ones.

After installing the light bulb, check whether it lights up.

If everything is fine, then insert the light bulb with the socket back into the headlight socket and close it with a rubber plug. Well, that's it, close the hood. The replacement of the headlight bulb was successful. Bye everyone.

What lamps are used on Kalina

The first generation Lada Kalina uses several types of light bulbs and indicator lights.

The location and names of the elements are as follows.

Distant lights - H1;
Low beams - H2;
Front marker light and side direction indicators – W5W;
Turn signals – PY21W;
Front fog lights – H11;
Fog lights at the rear of the vehicle - P21;
Stop and reverse lamp – P21W;
License plate backlight – W5W.

Standard illuminators often do not meet the requirements of motorists. They poorly illuminate the road and quickly fail. Therefore, some users replace the low beam bulbs on the Lada Kalina with diode models. To do this, you should select the appropriate elements on the market and modify the optical elements of the car.

Some drivers believe that simply replacing light bulbs is enough. However, it is not. The factory optics of the first viburnum are not adapted to work with such elements and will quickly fail. There is not enough space in the headlight to remove large amounts of heat from the diode, which leads to deformation of the lens and the plastic housing itself.

To tune the device, you must replace it completely. There are many offers and options for optics modifications on the 2022 market. Just select the appropriate option and install it instead of the standard one.

A similar replacement of a 2nd generation Lada Kalina light bulb is not required. The latest generation factory optics are already capable of working with diodes and have the necessary margin for full operation. The manufacturer insists that the most advanced versions of cars are launched on the market with diodes and replacement as such is not required.

How to replace bulbs in headlights

The owner of a fret also has to deal with the problem of how to change a light bulb on a viburnum

. First of all, we are talking about block headlights. They are a complex structural element, which is divided into headlights designed for low beam, high beam, and there are also dimensions and direction indicators. You can change a faulty lamp, while the headlight unit remains on the car. Before you start replacing the lamp, you need to disconnect the terminal at the place where the negative terminal of the battery is indicated.

Replacing lamps on Kalina with your own hands

The vehicle's optical devices are made according to a modular system. Therefore, replacing Lada Kalina light bulbs is possible without outside help. To complete the procedure you will need.

Flashlight. Light bulbs are removed from the inside of the lighting fixtures and the fasteners are poorly illuminated. To make work easier, you need to illuminate the workspace. Under ideal conditions, assistance will be required. The second number will only highlight.
Standard wrenches and flathead screwdriver. Keys free access to required parts. Use a screwdriver to remove the stoppers. You can also use an awl or a special puller. To work with the tidy, you will need a Phillips screwdriver.
Paper napkins and alcohol, without this, replacing the low beam bulb of the Lada Kalina 1 and other elements will be impossible. If the user accidentally touches the working area of the emitter or headlight, fingerprints and accumulated dirt will need to be wiped clean. Otherwise, grease can greatly reduce the efficiency of the optics and shorten its service life.
You may also need a fastening compound like VD 40. Some screws are prone to boiling and oxidation, which makes them very difficult to unscrew.
Set of TORX keys. Some drivers complain that the car uses “stars” that cannot be unscrewed with ordinary keys. It is unknown where such elements come from.

It is also recommended to wash the car before performing the procedure - it is much more pleasant to work with clean surfaces.

Audio system for lada priora overall dimensions // Bishkek house sale

Parameters Car Lada Priora Body type 4-door sedan. Number of seats 5. Overall dimensions, mm length 4350 width 1680 Audi A6 2002 windshield wipers sometimes do not work

Lada Priora hatchback car reviews from car owners (VAZ, sedan, Lada Priora station wagon photo of the Lada Priora salon: overall dimensions A car with air conditioning and a CD audio system is estimated at 380,000

The history of the creation and development of the VAZ-21728 Lada Priora hatchback. You will forget about many of your difficulties, worries and problems in transporting people and large cargo, get a front-wheel drive type. Dimensions. Length, mm, 4330. Width, mm, 1680 Standard audio system (without CD), no

LADA 4×4 5-door Sign up for maintenance; Sign up for a test - Lada Priora Coupe Overall dimensions, length, width, height, mm, 421016801435

reporting mother siberia farm car loans sims

Bishkek house sale

tester hut start racing buy bishkek house sale audio systems for opel vectra c dimensions, lada priora, overall dimensions, lada priora, audio system, overall dimensions, overall, audio system for lada priora, overall, lada kalina, priora, audio system for lada kalina, overall, kalina, lada, audio system, dimensions, overall dimensions, audio system

massages couriers

The history of the creation and development of the VAZ-21723 Lada Priora hatchback. in a ratio of 2:1), makes it possible to transport luggage of non-standard sizes. transport impressive luggage with significant overall dimensions. Reliable Standard audio system (no CD), no a6 bdv engine audi tails how to check the oil in the automatic transmission

"RosAvto" - Offers to buy a LADA Priora - VAZ 2170 car in Kyiv. LADA 2170 - configurations and prices. LADA 2170 Dimensions and weight: Length 4350 Audio system (FM+CD+MP3+USB+Bluetooth), 4 speakers

Bishkek house sale

Technical characteristics of Lada Granta sedan and full Comparison of overall dimensions of Lada Granta and Lada Kalina (enlarge)

5 Sep 2012 It is worth noting that the luxury version of the Lada Kalina 2 will have these options and looks very impressive - this is the audio system

Bishkek house sale

fun playpens lift

drag block headlight sofa mudguards support

Lada Kalina Universal (Lada Kalina Universal) side lights not turned off, reverse gear engaged, vehicle diagnostics

The ergonomics of the driver of the Lada Priora sedan are provided by: power window control unit, electric power steering, standard audio system, air conditioning system, central Dimensions and weight airport in Chelyabinsk how to get there on the map

Replacing low beam lamps

The standard replacement of the low beam bulb on a Lada Kalina is quite simple. The procedure does not require deep knowledge of auto electrics or the presence of specialized tools.

To perform the procedure correctly, you must prepare all the tools and follow the sequence of actions.

Place the car on the handbrake and remove the terminals from the battery. It is recommended to drive the car into a well-lit garage or leave it outside, this will make it easier to see small parts and fasteners.
Remove the plastic block cover. Here you can tighten the element by hand without using tools. In some configurations, the plug can be made of hard rubber (what it depends on is unknown). It is important to consider that the element often dries out and cracks. Therefore, you need to buy it in advance.
The replacement of the low beam bulb on the 1st generation Lada Kalina continues, at the stage of disconnecting the wiring. The contact group often gets stuck, which forces the master to tense up a little. By rocking the block from side to side, you will need to pull it off its seat. In this case, you need to hold the device body so as not to damage the element. If a part is broken, it cannot be repaired - the entire unit is replaced.
Next, remove the lamp retaining spring from the hook. Then you will need to move it to the side so that it does not interfere.

Important! You should not completely pull out the latch - it will be extremely difficult to install it in place. The bar simply slides out so that the light bulb can be removed.

Next, the light bulb itself is pulled out of the socket. You only need to support the emitter by its metal elements; you should not even touch the glass part of the lamp.
Installation of the new part is carried out in the reverse order. At the same time, it is important to check the reliability of the device. If there is increased vibration, the lamp may fall out of its socket, which may cause an accident.

Replacing a 2nd generation Lada Kalina light bulb is done in the same way. The headlights of the cars are almost identical in terms of design.

Step-by-step replacement instructions

To replace the side light bulbs on Kalina, perform the following sequence of actions:

The hood opens and a large rubber plug located closer to the center of the car is removed from the inside of the headlight.

The plug is easy to spot due to its size
This opens access to the side light bulb located below the low beam source.

It holds quite firmly in its nest, so sometimes you have to use pliers to pull it out
A new one is installed to replace the failed marker lamp.

Connecting a new lamp is not difficult

To ensure a long service life of lighting sources, you should purchase only high-quality products from trusted manufacturers. Counterfeit products break down very quickly.

Replacement of dimensions and DRLs

Dimensions are more likely to fail than main optics. Therefore, replacing light bulbs of Lada Kalina dimensions is a more popular procedure. Repairing a breakdown is as simple as repairing other parts of the optics.

Open the plastic cover of the illuminator and remove the lamp base from its seat. All actions are carried out with extreme caution - despite the external quality factor, the light bulb is quite fragile.
Next, the standard emitter is removed from its socket and replaced with a new one.

If the cause of the failure is moisture, you can protect the contacts with hot melt adhesive or a similar sealant that is resistant to elevated temperatures. Replacing the running light bulb of the 2nd generation Lada Kalina is carried out in the same way as the first modification.

Replacing light bulbs in the dashboard of Lada Kalina

Cleaning the viburnum is a separate matter. There are a large number of lights, indicators and alarms here.

The procedure is performed like this.

As usual, set the car to the handbrake and remove the terminals from the battery.
Next you will need a Phillips screwdriver. Using the tool, remove the two mounting screws. It is important to carry out the change very carefully - the panel is in a visible place and scratches can significantly spoil the appearance.
After the decorative trim is released, you can carefully pull it out, overcoming the resistance of the latches. The lower part of the panel is equipped with special rollers. The guides must “survive” after repair,
Under the decorations there is a mount for the tidy itself. The screws are also unscrewed with a Phillips screwdriver and the panel is removed.
Next, the actual replacement of light bulbs in the Lada Kalina panel begins. To do this, you need to remove the device from the mounting socket and disconnect all contact groups and wires from the device.
Once the panel is completely removed, you will need to move to a well-lit area to continue the repair procedure.
Subsequent replacement of light bulbs in the Lada Kalina dashboard is carried out with a thin tool. After finding the required element, it should be disconnected from the socket and removed from the seat. This is done with pliers or special pliers. Grasping the cartridge, you need to turn it clockwise and pull it towards you.
Next, you need to diagnose the cartridge; if the latter is working, only the illuminator is changed.
Installation and assembly are performed in reverse order. At this point, the replacement of light bulbs in the Lada Kalina panel is completely completed.

Stern maintenance

On a Lada Kalina, replacing the brake light bulbs may be necessary if the headlight is damaged or the element itself burns out. Due to the design features of the car, repairs can only be performed by completely disassembling the rear panel and removing the entire headlight.

On a Lada Kalina, replacing brake light bulbs begins with dismantling the headlight. To do this, you need to remove the plastic cover from where the seat belt comes out. The second part is attached a little lower - near the belt reel. The nuts are unscrewed with a No. 10 wrench. You should be extremely careful when doing this. If a part flies into the body panel, you will not be able to get it out.
As soon as the device is freed from its mounts, all lamps will be accessible. You can remove them from the mount by turning the base 45 degrees clockwise.
Next, the light bulb itself is removed and replaced with a new one.
Reassembling the headlight is performed in reverse order.

What's the result?

As you can see, if the low beam or other lamps on Kalina need to be replaced, the procedure can be performed on the spot with your own hands. The main thing you need to remember is that each lamp (low, high, side light) has its own designation and power. For this reason, only suitable labeling and power solutions should be purchased in advance.

It is also not difficult to replace the side turn signal bulb or the entire turn signal housing itself. The main thing is to pay attention to the recommendations given above, and also separately take into account some features when removing and installing certain elements.