Nissan qashqai j11 DIY cabin filter replacement

As a rule, the cabin filter on a Nissan Qashqai is changed during a scheduled engine oil change, i.e. once a year. And if the car owner, as a rule, does not have any problems with the oil change, then, on the contrary, difficulties may arise with the cabin filter.

Also, a lot depends on what model of car you have: j10 before 2013 (British assembly), or j11 (after 2013).

The thing is that the cabin filter on the Nissan Qashqai j10 is located in an inconvenient place - behind the heat damper drive and the pedal assembly.

There are two ways to go here:

Replace without removing these components. The disadvantage of this approach is that the product will have to be strongly compressed; as a result, it will not fully straighten in its normal place, which can lead to contamination of the air conditioner evaporator.
Replace with dismantling of the above components. This method is labor-intensive, but more preferable, since the filter element can be completely straightened, filling the entire space of the casing.

In the Nissan Qashqai j11, the cabin filter is located in the same place as in the j10, but it is changed on the passenger side, which greatly simplifies the situation.

For replacement, use the original product with part number 27277-4BU0A.

How to replace cabin filter Nissan Qasqai J11

Nissan's maintenance regulations do not require replacing the cabin filter on the Qasqai J11 every scheduled maintenance. However, when used on Russian roads, within the period specified in the regulations, the cabin filter becomes quite clogged and does not perform its functions. We recommend replacing the cabin filter on the Nissan Qashqai J11 every 8-10 thousand kilometers.

Safety precautions during work

When repairing your car, pay attention to safety precautions. Considering that part of the work on changing the engine oil of a Nissan Qashqai engine can be carried out under the bottom of the car, and the ground clearance, depending on the vehicle configuration, is 185-200 mm, there is a possibility that you will be crushed by the car

Therefore, to prevent the machine from spontaneously rolling, be sure to install wheel chocks. If the car is raised with a jack, be sure to place stops under the car to prevent the car from falling.

Motor oil has a negative impact on the environment, so dispose of it and other repair waste in specially designated areas.

Source

Which filter to choose for replacement

Nissan filter 27277-4BU0A is installed from the factory ; its price starts from 600 rubles. In addition to the original filter, you can install analogue filters from Chinese, Russian or European manufacturers. When choosing a filter, you should pay attention not only to the brand, but also to the cost of the filter. Filters that are too cheap do a poor job of cleaning the air.

Filter analogs 27277-4BU0A

Alco Filters MS6477 from 350 RUR
Filtron K 1355 from 180 RUR
Fortech FS148 from 160 rub.
Fortech FS148C coal from 300 rub.
FRAM CF-11854 from 300 RUR
Goodwill AG4221CF from 250 RUR
JS Asakashi AC2513 from 290 RUR
Sakura CA18360 from 360 RUR
TSN 97882 coal from 350 RUR

For Nissan Qasqai J11, cabin filters are offered both carbon and regular. Their differences are that a carbon filter better filters the air and odors entering the cabin, but its cost is higher compared to conventional filters.

Instructions for replacing the cabin filter

Replacing the filter itself will not cause any particular problems even for novice car owners. On a Nissan Qasqai J11, you can replace the cabin filter in two ways - the first is without removing the glove compartment, the second method is with removing the glove compartment. When replacing the filter using the first method, you will have to work hard to crawl up to remove the cover of the filter housing and get the filter itself. The second method is much easier in this regard.

Choosing an oil filter

Having decided on the choice of oil, you should purchase an oil filter, since it is changed at each scheduled oil change. The original Nissan filter has the article number 15208-9F6OO, made in the UK, and the article number 15208-65F0A, made in Japan. The cost of original filters starts from 400 rubles.

Analogs of original filters

Filtron OP595 price from 170 rub.
MANN MF W67/1 price from 350 rub.
Sakura C1823 price from 180 rub.

There are also other analogues; above we have indicated the most popular filter analogues of good quality.

When changing engine oil, we also recommend replacing the O-ring of the drain plug. This is necessary to prevent oil leakage from under the plug in the future.

O-ring Nissan 11026-01M02 price from 30 rub.

LEX WW0829 from 30 rub.
OHNO YH0114P from 50 RUR
Ajusa 18000900 from 25 rub.

Now, after all the preparatory measures, you can proceed directly to changing the oil.

Replacing the filter by removing the glove box

We disconnect the “microlift” from the glove compartment as shown in the photo

We unscrew the 5 mounting bolts - 3 outside and 2 inside, disconnect the backlight wire and pull the glove compartment out of its seat.

The photo shows the location of the filter. Open the cover of the filter housing and take out the old filter element.

Before installing a new one, we clean the housing from dust and possible leaves and install a new filter.

In order for the filter to “stand up” evenly, it must be slightly bent and inserted into the housing evenly so that it fits evenly and straightens into the housing itself. If the filter is installed crookedly, the incoming air flow will be lower.

Choosing a cabin filter for Nissan Qashqai

The factory code of the original spare part is 27277-EN000. Also, according to VIN, catalogs can issue article numbers 999M1-VS007, 27277-EN025 - this is the same part, the designations were simply standardized between models, this is a common practice for the Renault-Nissan concern. Moreover, the set of original delivery to dealer shopping centers has its own numbers (B7277-EN00M-VA, AY684-NS009), although it is still the same filter.

It is inexpensive, which partially compensates for the complexity of replacement. If the original is not available or the seller is completely confused about the five markings for one car, you can look in the direction of a non-original: “Nevsky Filter” NF-6351 (the cheapest, but quite high-quality paper filter), TSN 9.7.371 (without carbon filler), TSN 9.7.372 (carbon), Champion CCF0058, Filtron K1255, MANN CU1936, Knecht LA396, Delphi TSP0325227C.

Replacing the filter without removing the glove compartment

On the Russian assembly of the crossover, you will need to unscrew the screw securing the filter housing cover and only then press the latch and pull out the cover.

So, we reach under the glove compartment with our hand and use a Torx 20 sprocket to unscrew the self-tapping screw that holds the lid.

Press the latch and remove the filter housing cover. The cabin filter is visible in front of us.

We carefully take it out, clean the housing of dust and debris, and install a new filter.

Useful tips

To carry out the procedure for replacing the filter yourself and not harm yourself and the car, the following tips will help:

The plastic cover of the center console should only be removed in a warm car and in a warm room. In the cold, the plastic becomes too brittle and there is a high risk of breaking the latches.
If replacing the Nissan Qashqai cabin filter is expected in the fall, then you should wait until the leaves fall and the leaves are cleared from the roads. Fallen leaves easily and quickly clog the filter, resulting in a much shorter lifespan.
To return the throttle switch gear in the cabin to the desired position after finishing work, you should put some marks (for example, with a marker) and, best of all, take a photo of it.
To make it easy to put the new cabin filter in place, you can twist it slightly along the longitudinal axis or bend it. Its body is made of fairly flexible and elastic plastic. Therefore, it is difficult to break, and once in the right place, it can easily straighten out on its own.
The correct operation of the filter depends on its correct placement. Therefore, it is necessary to focus on the arrows or other marks indicated on it (depending on the manufacturer).

Correct and timely replacement of this consumable guarantees the correct operation of the stove and air conditioner, as well as comfort in the car interior. The air will not only be cleaner, but also safer for health, especially if you choose a carbon filter that traps pathogenic microflora.

Useful tips for replacing the cabin filter

To ensure that the air in the cabin is always clean, replace the cabin filter regularly.
If the heater does not heat well in the winter, the side windows or windshield become foggy - the cabin filter may be clogged.
Is there little air flow from the air conditioner into the cabin? Perhaps the problem is precisely in the cabin filter, since air flows through a clogged filter extremely poorly.

The instructions were prepared specifically for the site https://1remontauto.ru.

Share the post “How to replace the cabin filter Nissan Qasqai J11”

Source

Selection rules

Selecting a filter is easy. According to the manufacturer's recommendation, preference should be given to the original element. Of the two types of models, conventional and coal, it is worth choosing coal products. They qualitatively purify the air in the cabin and rid it of pathogenic microelements, carbon dioxide and smoke.

When choosing, you should start from:

type of structure;
cost;
quality level;
material: carbon filters better retain particles and prevent unpleasant odors from entering the cabin;
type of coating: the best is electret, capable of catching the smallest particles;
properties (there are antifungal and antibacterial options);
dirt holding level.

Stages of replacing the filter element Nissan Qashqai J11

The second-generation Nissan Qashqai J11 parquet crossover enjoys deserved popularity among Russian car owners. But its drivers, like many others, often complain about the presence of foreign odors in the car interior.

Agree - it’s not very pleasant if all the aromas of a KAMAZ parked next to you in a city traffic jam spread inside the cabin. The cause of such unpleasant phenomena, as a rule, is contamination of the cabin filter. A dirty air filter in a Nissan Qashqai J11 not only allows foreign odors to enter the cabin, but also interferes with the quality operation of the air circulation system inside the car.

Experts advise changing the cabin filter based on the degree of contamination. Often, contamination occurs long before the scheduled time for replacement. But to understand the condition of your cabin filter, you first need to get to it. You can contact a service station, or you can carry out this operation yourself; fortunately, this does not require any special technical knowledge.

Where is

On new second-generation Nissan Qashqai J11 models, the cabin filter element is located in the passenger's feet on the left side, next to the center console. The replacement is quite simple; some owners remove the glove compartment for this operation, but this is not at all necessary.

When installing a new cabin filter, you need to make sure that it is not deformed, since the bent shape will allow unfiltered air to pass through. Before starting work, it is necessary to cover the workspace with rags so as not to stain the interior with old leaves and dust that accumulate in the filter housing.

Replacing the cabin filter Nissan Qashqai J11

Replacing the cabin filter on this generation is very simple, bend down and climb under the glove compartment, pull off the lid, take out the filter, install a new one, close the lid.

Now let's go through the points:

We climb into the cabin from the front passenger side and move the seat all the way back.
Under the instrument panel (next to the center console on the left) we find a lever, in the picture below it is circled with a red square.
Press the lever and remove the plastic cover. The latch must be snapped off carefully; the plastic may break off.
On cars manufactured in St. Petersburg, the filter protective cover is held in place by a Torx T30 screw.
We remove the old filter, install a new one, and mount the plastic plug in place.

There are a minimum of replacement operations here, so almost any driver can do this work with his own hands. True, there are nuances in this matter - when removing the filter element, you don’t have to be afraid of crushing it, since it will no longer be useful, but installing the filter element is not always easy.

The filter element fits tightly into its seat, usually it easily goes through two thirds, and then it has to be pushed in. Filters with longitudinal ribs are best placed in their place; they do not wrinkle during installation.

Changing the cabin filter on Qashqai J11

Replacing the second-generation Nissan Qashqai cabin filter (first introduced at the end of 2013) is done a little differently. The fact is that the filter element is located in the feet on the passenger side. It is worth noting that on cars manufactured in St. Petersburg, the protective filter cover is held in place by a hexagon screw. Therefore, in addition to a flat-head screwdriver and a flashlight, you will also need a wrench of the appropriate size.

We disconnect the smooth opening mechanism of the glove compartment, unscrew the top cover of the glove compartment, 3 bolts outside and 2 inside

The replacement procedure is carried out in the following order:

The front passenger seat moves back as far as possible. A flashlight is placed on the floor for better visibility.
To the right of the center console there is a plastic cover that hides the filter. It is dismantled using a screwdriver (on a Russian-built car, a screw is unscrewed with a hexagon).
The filter element is carefully removed from its seat. At the same time, you need to try not to scatter the garbage that has accumulated there around. A new one is installed to replace the old one, and the lid is returned to its place.

Replacing with a second generation Qashqai is easier, since access to the filter unit is freer.

When to change, what interior to install

Replacing the cabin filter on the Qasqai J11 is provided for every 2nd scheduled maintenance, that is, after 30 thousand km. However, when used on Russian roads, within the period specified in the regulations, the cabin filter becomes quite clogged and ceases to perform its functions. Owners recommend replacing the cabin filter every 10-15 thousand kilometers.

The ideal option is to change the Nissan Qashqai cabin filter 2 times a year, once in the winter season, and once before the summer season. In the spring and summer, it is better to install coal, as it copes more effectively with various allergens and unpleasant odors. And in autumn and winter, the usual is enough.

Although the service book indicates specific terms for replacing the filter element, it is often recommended to carry out the replacement earlier, that is, not according to regulations, but as needed. The basis for replacement are signs of filter contamination:

increase in air humidity in the cabin (fogging of windows);
reduction of ventilation and heating system power;
the appearance of unpleasant odors in the cabin (exhaust gases, smoke, fumes, etc.);
noise appears when ventilation is turned on to maximum.

On the Nissan Qashqai J11, the cabin filter is usually installed as a carbon type. For its production, activated carbon is used (impermeable to carbon dioxide, dust, etc.) and synthetic material.

Suitable sizes

When choosing a filter element, owners do not always use products recommended by the car manufacturer. Everyone has their own reasons for this, some say that the original is unreasonably expensive. Some people in the region sell only analogues, so there is a need to know the sizes by which you can subsequently make a selection:

Height: 34-36 mm
Width: 179-181 mm
Length: 249-251 mm

Selecting an original cabin filter

The second generation Qashqai J11 is equipped with a regular dust cabin filter from the factory under article number 27277-4BU0A. As drivers note, its main drawback is that the ribbed folds of the filter paper are located vertically. This makes it difficult to install.

There is also an original filter that is not installed from the factory, article number 27277-4BA0A. Its folds are horizontal, making installation easier.

In addition to the original interiors from Nissan, the Qashqai 2 can be equipped with some Renault cars. In particular, the filter under Renault article number 272775340R is suitable and is a complete analogue of 27277-4BA0A. Also a new original carbon cabin filter, article number - 272775081R. They are all the same size.

Which analogues to choose

Popular analogues among car owners are:

Conventional dust cabin filters

MANN-FILTER CU25003 – vertical fins, not the most convenient installation
MANN-FILTER CU25012 – PV fins are placed horizontally, which simplifies installation
Filtron K 1355 – relatively inexpensive

Carbon cabin filters

AMD FC759C – high-quality filter paper and carbon coating
Citron TSN 9.7.882 – the best in the price/quality category
MANN-FILTER CUK 25012 – thick carbon coating, famous brand

Also, for the Qashqai 2 crossover, the industry produces filters of original and non-original production; car owners are offered products from different manufacturers:

Corteco
SCT
Sakura
GoodWill
Fram
JS Asakashi
Champion
Zekkert
Masuma
BIG Filter
Nipparts
Purflux
Knecht Mahle
Nevsky Filter nf

Depending on the manufacturer, materials may vary. In terms of price, the cost of parts ranges from 250 to 800 rubles. In addition to simple cabin filters, there are also carbon filters that filter the air more effectively, but they are more expensive.

The advantage of coal SF is that it does not allow foreign odors coming from the road (street) to penetrate into the car interior. But this filter element also has a drawback - air does not pass through it well. GodWill and Corteco carbon filters are of fairly high quality and are a worthy replacement for the original.

On Nissan Qashqai J11 cars, SFs with a longitudinal “accordion” are installed without any problems; they easily fit into place and practically do not wrinkle during installation. There are non-original “consumables” that are almost twice as thick as the original, but it is unknown whether there will be normal air filtration with such elements.

Source

Increased product consumption

High oil consumption is a consumption that exceeds 0.5 liters per 1000 km. The engine consumes more lubricant due to increased engine speeds, so the tolerance of 3000 revolutions should not be exceeded so that Qashqai oil is not consumed more than normal. You should check the compression in the cylinders, the crankcase ventilation system, and possibly clean the valve. And then replace the oil seals and valve seats.

There are also cases when the lubricant is not consumed, but simply when replacing it could not be filled enough.

Experienced drivers often say: “I know why the engine constantly eats above normal.” They give examples of such situations on the forums and give advice:

Seals that are leaking can eat oil on the Nissan Qashqai 2.0. This is very easy to check: oil leaks have appeared under the hood.
Leakage through the gasket in the cylinder block occurs due to improper tightening of the power bolts or simply overheating of the engine.
There is a gasket on the oil filter, it can leak. When replacing the filter, lubricate the sealing ring with lubricant and tighten the filter tightly.
There are oil-deflecting valve caps that are installed in the engine. Leakage may occur through them.
The oil scraper piston (control) rings have worn out, which eats up the lubricant.
The problem is overheating of the piston rings, which can increase oil consumption.
Increased oil burn appeared due to ring flutter. This happens due to a decrease in the elasticity of the compression rings.
Coking of piston rings. Such rings cannot seal gases or lubricants. This is why the engine consumes more lubricant and compression decreases, but often only for one or two cylinders. Oil burns due to this problem can occur among drivers who use low-quality engine oil in Nissan Qashqai cars. That is, the product has very weak cleaning ability, or it has lost this ability due to long-term operation. Therefore, it should be recalled once again that the best solution is to use an original consumable that exactly fits all the requirements. This will help avoid such problems. Russian car dealers often use poor lubricants that do not meet the requirements.
Destruction or breakage of the piston intervalve bridges. This may occur due to increased leakage of lubricant into the cylinders or deterioration of the combustion chamber seal. More liquid and boat gases flow through the ventilation system than necessary.
The reason why cylinders consume oil lies in their wear. This is not difficult to detect. You should check them for scratches, burrs, chips; it is also possible to increase the diameter.
Driving with increased lubricant viscosity.
Delayed combustion in cylinders.
Unfavorable modes of engine use affect oil consumption. A gasoline engine, which often runs at high speeds and loads, consumes significantly more consumables.

Dropping on Qashqai J10 and J11

If, after carrying out maintenance work, the question arises of understanding which generation of Qashqai. There is the first generation J10, produced before 2013, and the second generation J11, produced after 2013.

Qashqai before update on top, restyled 2010 below

To reset on J10 models, you will have to perform the steps in the following order:

Turn on the ignition, turn the key to the “ON” position;
We are waiting for the meter readings to display;
After the readings are displayed on the display, press the knob located to the right of the display;
Without releasing the handle, we wait until the indicators start blinking on the display;
After the indicators start blinking, release the button and press again;
After pressing again, you will be able to change the indicators. If you rotate clockwise, the indicators will begin to increase. If you turn counterclockwise, the indicators will decrease by a thousand km per turn;
After you have set the required value, release the button and start the car. The on-board computer will display the set values.

Nissan Qashqai J11 before and after update

On second generation models, resetting readings is much easier. We perform the following actions:

Turn on the ignition and wait for the corresponding indicator to appear;
Let's go to settings. To do this, press the “Reset” button;
To change the readings, scroll the lever to the “Maintenance” section;
Let's enter the section. To do this, press the lever;
We wait until “Reset” appears on the display, then select the corresponding “Reset” item and press it.

If the described actions are performed correctly, then the next time you start the engine, the new set values will be displayed on the car display. If the information has not changed, then most likely errors were made during execution, and you will have to perform the necessary actions again.