Lada Kalina reverse gear disappeared, what should I do?

A modern car is literally packed with electronics, and the Lada Kalina is no exception in this sense. On the one hand, electronics make life much easier for the driver. On the other hand, it can also become a cause and source of headaches for the driver, since the abundance of electronics can seriously complicate troubleshooting. The most common electronics-related problem on Kalina is the inability to engage reverse gear. We will tell you why the transmission does not turn on and how to fix it in this article.

Causes of reverse gear failure on Lada Kalina and ways to fix the problem

Technological progress does not stand still. More advanced technologies are being introduced into literally all areas of life. This also applies to cars: both foreign-made and domestic. However, updates are not always beneficial. For example, the electronics installed in the Lada Kalina do not so much make it easier as they complicate the life of the owner. The most common malfunction in this car, caused by the operation of electronic systems, is a refusal to engage reverse gear. The reasons and solutions to this problem will be discussed further.

Running in the “2181” gearbox: engage the “R” gear correctly

The Kalina cars of the first family used a manual transmission equipped with a reverse gear lock solenoid. If reverse gear did not engage, it was usually caused by electrical problems. Then the blocking was simply turned off and performance was restored. The new VAZ box, designated “2181,” uses a different locking method – mechanical. But not only a faulty lock, but also incorrect actions by the owner can prevent the reverse gear from engaging. How to operate the “2181” box will be discussed further, and we will talk about the break-in period. It is precisely with this that most of the problems are connected.

We study the design of the VAZ-2181 gearbox
Reading the instruction manual
A couple of practical tips
Training video: The 2181 gearbox can actually work perfectly

What is a reverse gear locking mechanism?

To move the car back in Kalina, a whole scheme is provided. The gearbox in the car is equipped with a special solenoid that helps engage reverse. However, the reverse connection mechanism has a somewhat unusual algorithm, introduced by AvtoVAZ engineers for the purpose of being on the safe side. First, the driver moves the gearshift lever toward himself and forward, gripping a special plastic ring. But what happens inside at this moment: the ring allows the magnetic switch to be activated, after which the solenoid moves to the ground of the car. This, in turn, allows the solenoid auger to move in the rearward direction.

Why the Lada Kalina stopped turning on: reasons and solutions

Failure of the locking mechanism fuse

Since this device in the Lada Kalina is of electronic origin, it is first of all worth examining the electronic systems. To do this, you need to check the condition of the corresponding relay and fuse, which are located in the mounting block. Its cover is located under the handle for turning on the dimensions. Open it and evaluate the functionality of the fuse responsible for the operation of the transmission reverse lock circuit.

The documentary designation of the required element is F21. The current rating of this component is 10A. The location can be seen in the photo below.

F21 (10) - the fuse you need

To determine the true cause, remove the fuse from its socket and carefully analyze the condition of the jumpers. If the part is damaged, the integrity of the jumper will be compromised.

Option to solve the problem: replacing the fuse with a new one is the only way.

Important! If a newly installed mechanism quickly fails, then the cause must be sought in the solenoid.

Magnetic switch failure

As a rule, such breakdowns are not so common due to the fact that the magnet itself is a fairly durable spare part and has a sufficient working life. However, if the reverse gear fails, it would not be superfluous to check it too.

The procedure is as follows:

Remove the cover from the manual transmission lever.

Stage 1: removing the protective casing
Locate the connector that connects the lever and separate it.
To check the operation of the reverse gear in stand-alone mode, close the contacts using a wire.

Where do you need to close the contacts?
Engage reverse gear.

But here there are possible options. If the reverse gear engages freely after completing all the manipulations, then the reason is in the magnetic switch. However, before disassembling the box and removing the magnet, it is worth analyzing the operation of the plastic ring: it should rise easily and without distortion until it clicks. Due to its wear, the ring may not move the required distance, and this may also result in reverse gear failure.

A solution to the problem: replacing the reed switch (magnet) or ring with new ones.

There is no voltage supplied by the solenoid to the manual transmission lever

This is most often the cause of malfunction of the reverse gear locking mechanism on Kalina. And here we must thank the AvtoVAZ engineers, who placed the wire supplying power from the solenoid to the lever in an unusually bad place - under the bottom of the car. He has to endure a lot: the action of reagents that are generously sprinkled on roads in winter, and water, and snow, and flying sand and gravel, and sudden temperature changes. Considering the lack of any adequate protection for this element, it is not surprising that it fails quite often. In most cases, wire rupture occurs at the point where it connects to the spar. Dirt and sand accumulate here, which act as rough abrasives, thinning the part.

Option to solve the problem: replacing the wire.

Solenoid faulty

This is evidenced by the absence of voltage at the solenoid contacts. To check the fact itself, you need to disconnect the contacts and test each of them with a multimeter. Performance indicators - 2.2 Ohms. If there is no voltage on one or the other wire and the parting shows “0”, then we are talking about a burnt-out solenoid winding. You can check this this way: switch the multimeter to ringing mode and repeat the voltage test procedure. If in this case both wires are “silent,” then it was the burnt winding that caused the failure of the reverse gear locking mechanism.

Solution to the problem: replacing the solenoid.

What to do if Kalina does not go in reverse (video)

Defects in the design of the Lada Kalina are the root cause of frequent car malfunctions, including in our region. This is eloquently evidenced by the most common cause - an unprotected wire located in the wrong place. Therefore, when repairing the reverse gear locking system, you should first pay attention to this option.

Hello! My name is Ann. I am 25 years old. By education, he is a teacher of Russian language and literature. I specialize in automotive topics. At different times I wrote for car repair shops and a noise insulation center. I try to develop and learn new things.

Source

Place of the switch in the light switching circuit

On cars with manual transmission, voltage to the lamps when reversing is supplied through a limit switch (the so-called frog), which is screwed directly into the gearbox housing. When reverse gear is engaged, the switch button is pressed inside the gearbox. The contacts inside the “frog” bridge, and current begins to flow to the lamps.

On the circuit diagram for turning on the reversing lights, we can see that on the VAZ 1118 Kalina, the current from the battery through the ignition switch (No. 2) is supplied to fuse F1. Passing through the fuse that protects the switching circuit, “+” goes to the limit switch (No. 10). The contacts are in a normally open state and close only when reverse gear is engaged. Thus, current begins to flow to the light bulbs. The second contact of the lamps is connected to the “–” battery through the common ground contact of the lamps.

On cars with automatic transmission, the role of the limit switch lies with the selector position sensor. Information about changing the location of the gearshift knob is transmitted to the engine ECU, the light control unit.

How to check the "frog"

Remove the headlight switch chip.
Turn on the ignition.
Using a small piece of wire, connect the contacts of the reverse gear sensor connector to each other.

If the reverse lights are on, then the problem is in the “frog”. Some drivers disassemble the switches, clean the contacts, after which the device continues to work properly. It is up to you to judge the appropriateness of such measures. But keep in mind that on many cars (including VAZ models) the limit switch is located below the oil level in the gearbox. We recommend simply replacing the power sensor. To minimize oil loss, jack up the car on the side where the end switch is installed.

On some cars, the reversing lights do not light up due to incomplete activation of the limit switch. The problem can be solved by installing a thinner washer under the “frog”. To make sure that the switch is working, check with a multimeter in ohmmeter mode whether the contacts close when you press the button.

Checking the circuit

The essence of diagnosing the reason why the reverse lights do not work comes down to identifying the section of the circuit where the voltage is lost. To do this, you can use a regular control light. Continuity testing is done with an ohmmeter, so you need to know how to use a multimeter.

You can start checking directly from the limit switch connector. Turn on the ignition. Connect one contact of the control light to an unpainted metal part in contact with the body, and the second to the “+” connector.

If power comes in, check the reverse sensor.
If after installing the “jumper” in the connector the lights do not light up, then the problem is in the section of the wire circuit going from the connector to the lights. Ring the wire to the point where it divides into light bulbs on the left and right sides. Most likely, the reason is the break.

To find the pinout of connectors, light contacts, and wire colors, be sure to study the electrical diagram of your model and vehicle configuration.

The lamps are constantly on

If the lights on your car are constantly on or come on regardless of whether reverse gear is engaged, the cause will be among the following breakdowns:

short-circuiting the “+” going to the reverse gear sensor and the light bulb wires from the switch;
the wire going from the connector to the lights has a short to “+” (this happens if the wires in the harness fray);
The sensor is stuck in a closed state.

Lada Kalina lost reverse gear

On Lada Kalina cars there is an insidious reason that leads to the inability to engage reverse gear. It is interesting that this reason is purely electrical and has nothing to do with mechanics.

Reverse gear on Kalina is engaged by moving the gearshift lever towards you and forward. In this case, you need to lift the plastic ring on the lever. This ring protects the driver from accidentally engaging reverse gear instead of first gear, as often happens on “tens”. This is done using an electric drive - a solenoid.

The solenoid is installed in the transmission and blocks reverse gear from being engaged until the ring on the gear shift lever is lifted. When raised, the reed switch (sealed magnetic switch) in the lever is activated, connects the solenoid power circuit to ground, the solenoid rod is recessed, and the stroke of the gear selection mechanism increases - you can engage the reverse gear.

We will not talk about the advantages and disadvantages of this system. There are two camps of “Kalinovodov”, who are both “for” and “against”. Here we will look at the reasons why problems with electrical locking may arise.

Lockout fuse blown

As always with electrical breakdowns, the first thing we look at is the fuse. Fuse F21, rated 10 A, is responsible for the operation of the reverse locking system in Kalina. It is installed in the main mounting block. If the fuse is intact, then move on to the gear lever. If the fuse jumper is broken, replace it with a new one and see what happens. We try to engage reverse gear. If the fuse blows again, it indicates that there is a short circuit in the solenoid power supply circuit. By

Restoring functionality

Reverse problems can occur throughout the reverse indication circuit. Therefore, you should not rush to drive the car onto an overpass and change the sensor. To begin with, it is worth checking out the more accessible places (but no less important).

Let's start with the ring on the gear lever. In principle, some craftsmen can easily disable both the sensor and the gearbox lock in 1 hour. But you shouldn't do this. This is not just a display system. It is also a security system. And since they did it (they didn’t save money on it), then this is a reasonable requirement. And any safety requirements, as you know, were written by those who neglected them.

The thing is that first gear and reverse gear are switched in the same way in the Lada Kalina: “toward and forward.” But the first speed is engaged simply, and the reverse with the help of a ring. Some protection “from accidents”. This is why you need a reverse sensor.

If you lift the cover that covers the gearshift lever, then under it you will find several wires running from the ring to special connectors. These wires are specially made not solid, but through a connector, because they are always in motion (the lever is pulled all the time). That's why they often break. It's worth checking them out first.

However, most often the Lada Kalina loses reverse gear due to the wires that lead from the sensor attached to the gearbox. There the wire is in “street” conditions. That is, it is influenced by all weather conditions that exist in the environment. Moreover, this is the bottom of the car. Sand, pebbles, dirt, moisture, etc. fly there. Of course, this is not directly under the wheels of the car, but closer to the middle, but still there is some constant impact.

These wires are easy to find. Lada Kalina does not have a very complicated gearbox. Therefore, the only electrical wires that go to the transmission are the reverse sensor wires. You should check them (or better yet, “ring” them, since every electrician knows that it is often impossible to see a break in a braided wire). If everything is in order here (rather rarely), then the reverse sensor itself should be changed.

Oil

The gearbox, just like the engine, contains oil. Its viscosity is thicker than motor oil. On domestic cars, the manufacturer recommends changing the fluid at least once every 60 thousand kilometers. If the reverse gear on the Lada Kalina does not engage, check the lubricant level in the box. If the mileage of the car is more than 60 thousand, drain the old fluid and use new one.

Locking fuse

Scheme for Kalina.

Fuse - F21 in the main unit, rating - 10A. A intact fuse indicates that there is no voltage at the solenoid.

If the fuse is blown, a new one is installed, then the gearshift lever is moved to the reverse gear position. If the jumper burns out again, the problem must be looked for in a short circuit in the solenoid power supply path.

How to change oil

To do this you will need an inspection hole or overpass. Warm up the car before surgery. Transmission oil is very viscous, and at low temperatures it will not completely leave the walls of the box. Locate the drain plug on the transmission. Using a wrench, unscrew it and place a container to drain the waste liquid. Within 20 minutes, all the oil will pour out of the box. Next, tighten the plug with a wrench and find the filler cap. It's on the side.

Backstage adjustment

Often after its repair, the Kalina does not engage reverse gear. The speed at which the pedal is pressed does not matter. Fifth gear will also disappear along with it. To eliminate the malfunction, it is necessary to adjust the position of the rocker. How to do it? You need to find the backstage clamp and loosen it.

Next, the lever is moved to the desired position (reverse or fifth speed). The clamp is tightened. You should check the effectiveness of the adjustment with the engine running. If after this you still cannot engage reverse gear on the Kalina, make the adjustment in first gear. Move the gearbox lever to the appropriate position, having first loosened the bolt. Turn the rocker drive counterclockwise until the lever rests against the reverse gear lock R. By adjusting the seating depth of the rocker on the gearbox driveshaft, you will restore the proper operation of the box.

How to fix the problem

All these problems will not allow you to drive safely. Therefore, it is urgent to repair worn elements.

Repair reverse gear chain

Most problems are related specifically to the wiring, which could have a break.

Starting at the fuse box, check the voltage at fuse 21. If everything is in order, then check the connector, which is located in the shift lever, under the leather cover. To do this, be sure to close the circuit by lifting the locking ring up.

If the problem remains unresolved, check the voltage at the solenoid and at its switching chips. To do this, you will have to unwind the twist of wires that goes from the fuse to the solenoid.

Adjust the rocker drive

Sometimes, to eliminate problems with gear shifting, you just need to adjust the rocker drive.

The problem associated with selecting reverse gear is solved by loosening the rocker clamp and placing the selector lever in the reverse gear position. After this, the clamp is tightened again.

Replace the plastic bushings of the gear shift mechanism

An extraneous rattling sound in the gearbox can irritate the owner. It's all due to the plastic bushings of the scenes.

To replace it, you need to remove the soft cover from the gear shift lever and unscrew the bolt that secures the lever with the rocker. Then you should dismantle the old worn bushings and install new ones in their place. It is advisable to use fluoroplastic bushings - they are more durable compared to factory ones.

Reverse gear "Lada Kalina"

After this procedure, extraneous sounds from the scenes will disappear, and reverse gear will engage more clearly.

Adjust or replace clutch cable

If the gears no longer engage clearly, you can try adjusting or replacing the clutch cable. For this:

Open the hood and remove the air filter housing, after first disconnecting the air flow sensor.
Remove the clutch cable from the fork.
Remove the driver's side front wheel. Now it is possible to remove the cable mounting bracket to the gearbox.
To remove the bracket from the cable, unscrew the plastic adjusting nut.
Remove the clutch pedal by removing the clamp securing it.
Pull the clutch cable through the interior. Install the new cable in reverse order.

To adjust the cable, you need to look at the gas, brake and clutch pedals. They must be on the same level. If the clutch pedal is not level with the other pedals, then tighten the adjusting nut located on the clutch fork. Bring the pedal to the same level.

Repair the box

The problem may be hidden inside the box. This is usually due to wear on the gears and stabilizers.

Solenoids

This mechanism is available on both automatic and manual transmissions. The solenoid is fed through a switch ring (located on the transmission lever). When you pick it up, the element fires. The solenoid rod is pulled inward. Reverse gear is engaged.

At the same time, the limit switch on the gearbox is activated, and the reverse lights turn on. Why doesn't reverse gear engage on Kalina? The reasons may be a blown solenoid fuse. It is marked "F-21". Check the fuse box and replace the burnt element.

Mechanical part

If the reverse gear on the Kalina does not engage, the reasons may be in the shift mechanism. The latter has a spring in its design. It breaks often. If the part “falls” to the bottom of the box, it will not interfere with gear shifting. The driver can drive like this for several years, not suspecting that a spring has fallen out of the mechanism.

But if it gets stuck in the grooves, reverse gear breakdowns will be inevitable. Depending on the position of the part, the speed may turn on periodically or not work at all. In this case, you will have to completely disassemble the gearbox and pull the stuck element out.

What to do if it is whole?

If reverse gear does not engage (Lada Kalina), the reasons may lie in another part. To diagnose, you need to disassemble the box cover. Below it there is a connector connected to the solenoid switch. We turn it off and connect the contacts directly. Check to see if reverse gear is engaged. If not, remove the solenoid connector and measure the voltage in it. When the voltmeter shows values less than 12 V, it means there is a short circuit. You can also check using a test lamp. Its power should be from 3 to 5 watts. If it does not light up, it means that the wires in the circuit have burned out. We are looking further. We close the contacts of the connector that goes down under the floor of the car. This can be done using a metal clip. Next, turn on reverse. If it turns on without problems, it means that the short circuit occurred here. If the element is in good condition, remove the connector from the solenoid. Using two pins and a tester, we measure the voltage. The ends of the tester are applied to the pins. In most cases, breakage occurs due to a fracture of the harness and oxidation of copper. Most often, the wire frays at the place where the clamp is installed on the mechanical box pallet. How to check it?

We remove the clamp chip and disconnect the connector that goes to the reversing lights. We take the harness out, remove the insulation from it and look at the wires. If they show signs of melting or other deformation, replace them. Cut off the damaged element with wire cutters and connect others. It is desirable that they be of the same diameter and cross-section. The connection method is twisting. But to be more confident, you can use a soldering iron and heat shrink. Don't forget to insulate the cord and place it in a corrugated area. It is important that moisture does not get on it. This way you will reduce the risk of oxidation. The clamp itself is replaced with a new one. After the repair, we connect this connector and check the serviceability of the box. If the solenoid is faulty, the resistance level should be measured. This indicator is 2.2 Ohm. If an element fails, the transmission oil is also changed. The threads and sealing elements are lubricated with sealant. Otherwise there will be smudges on the box.

Also check out

Using a paper clip, we close the contacts of the connector from which the wires are lowered under the floor of the car. Try to engage reverse gear. If this works, the switch is broken.

Disconnect the connector from the solenoid and install 2 pins into it. Use a tester to change the voltage. The device readings should be 12 Volts. It is worth charging it with a light bulb (5 Watt or 12 Watt). If it does not light up, then there is an open circuit, and the voltage arises due to resistance formed due to copper oxide. Very often, breaks and fractures occur on the harness in the place where the clamp is located on the pallet.

Remove the clamp by pressing its fastenings at the bottom.
Disconnect the connector from the stop switch and remove the harness. Remove the electrical tape from the corrugation, after which you can remove the wires. In the event of a break or breakage, characteristic signs will be noticeable.
Use wire cutters to disconnect the wires and connect them of similar cross-section and diameter. The twist should be soldered and insulated (you can use heat shrink). If necessary, put on a new corrugation. This is done so that moisture does not penetrate inside, otherwise it is possible that all the troubles will happen again. The harness should be secured with a plastic clamp.

Connect the connectors and check the operation of the solenoid. Failure of this element is quite rare. To check it you need to connect a tester. The resistance should be 2.2 Ohm. If the cause of the malfunction lies there, you will need to drain the oil from the box. One option is to quickly block the hole with something and install a new solenoid. In this case, it is important to apply sealant to the threads so that oil does not ooze down the threads during operation.

Release bearing

This element is very reliable. But do not rule out its breakdown. How to determine that it is the release bearing that has failed? To do this, you need to squeeze the clutch with the engine running and listen to the operation of the box. If, when you release the pedal, the characteristic sound (rustling) intensifies and the reverse gear on the Kalina does not engage, the reasons are in the bearing. But not only this speed will turn on poorly. Often, due to the “squeeze”, subsequent gears do not work well. They have to be turned on with re-gas and double squeeze.

Reading the instruction manual

The instructions included with Kalina-2 hatchbacks and station wagons say the following:

According to reviews, 3 seconds will be enough. By the way, the blocking stops working not after 3 seconds, but earlier. But if you switch immediately, there is a risk of breaking the gear teeth. All this, of course, is true only for the break-in period.

As the owners themselves say, reverse gear is engaged perfectly even on a car with “zero” mileage. But the driver is required to show dexterity: having squeezed the clutch to the maximum, the pedal is then moved back a little. The handle moves to the desired position and the pedal is fully released.

Clutch pedal response zones

You can also turn it on “through neutral”. This method is the most reliable. Release the pedal when the handle is in neutral and you are guaranteed to be able to shift into any gear. Actually, the method is suitable for any car and any manual transmission. But regarding AvtoVAZ products, the advice sounds like this: take a 3-second pause.

2 Reed switch and bearing failures – such misfortunes also happen

Let's consider other common reasons that do not allow the use of reverse gear on regular and tuned LADA Kalina 1 and LADA Kalina 2. The reed switch may have flown. The functionality of this element is easy to check. We dismantle the decorative casing above the lever in the car interior and look for its connector. We remove the last one and close the contacts. This operation can be performed using a piece of wire, a paper clip, or any other suitable device at hand.

After mechanically closing the wiring, we try to turn on the reverse gear. If the problem is solved, leave everything as is. We're going about our business. And at the first opportunity we go to a car service and completely change the reed switch. It is impossible to operate a car with the wiring connected according to the specified diagram for a long time. Note that failure of the reed switch is most often caused by rotting of its contacts or the entry of small particles of dirt and debris into the mechanism.

It makes sense to check the reed switch when, when you try to engage reverse, you do not observe any reaction from the car. The gearshift switch simply does not go down, no matter how much pressure you put on it.

If the reverse gear is engaged, but the driver does not hear the characteristic sound with which the additional gear comes into operation, we can safely say that the release bearing is faulty. It usually breaks due to metal filings or waste oil that has penetrated the gearbox mechanism. These pollutants increase the friction force. This causes rapid wear of the bearing, and in some cases leads to combustion of the entire mechanism. The described problem can be solved in one way - you need to install a new bearing.

We study the design of the VAZ-2181 gearbox

The force from the handle is transmitted to two gear selector levers (see figure). But these levers cannot move in any way - their trajectory is limited by the slots in the “3” grid. The pin "2" can be moved inside the slots, and the upper right part of the grille is closed with a latch "4".

Gear selection mechanism of LADA cable box

To open the latch, the following condition must be met: the car should not move forward even at low speed. Let's look at how blocking actually works:

A stop is made;
A certain amount of time passes;
The lock is deactivated.

In order for the reverse gear to become fully unlocked, you need to wait less than a second after stopping the car. But it’s unlikely that you’ll be able to start moving on a slope while engaging reverse. But if the slope of the surface is directed backwards, the gear engages immediately.

3 Repairing the solenoid - all operations for independent work

We have already told you how to replace the wires leading to the solenoid. Now let's look at the rules for repairing the Kalina locking mechanism. Its malfunction makes it impossible to turn on the rear. To perform this type of repair, you need to look at the solenoid control circuit. It is given below.

Failure of the mechanism in most cases is caused by the failure of fuse F21 (it is rated at 10 A). Through it, as can be seen in the diagram, 12 V is supplied to L1 (solenoid). Then S1 (switch) closes the circuit to ground. As a result of this, the solenoid coil is activated. If the fuse is blown or the switch is faulty, reverse gear will be locked. Let's solve this problem. We take out the fuse (if you look at the left, it will be the eighth one), and check it with a multimeter. Instead of the faulty element, we install a new one (of strictly the same rating - 10 A). When F21 starts working, we work on the switch (see the first section of the article).

If replacing the switch and fuse does not produce results, remove the connector from the solenoid. We put regular pins in it (two pieces). We measure the voltage with a multimeter. With a normally operating mechanism, it is equal to 12 V. If the readings are different, we have a break in the electrical harness on the pallet - at the place where the clamp is mounted. We pull out the entire harness, expose the wires, and eliminate the break. We solder the twisting area and treat it with heat shrink for greater reliability.

In very rare cases, the solenoid itself breaks down. You can check if it is faulty with a multimeter. We connect the device to the solenoid and measure the resistance. If we see a value other than 2.2 Ohm, we will have to change the element. The work is not difficult, but quite dirty. You will need to drain the oil from the gearbox, then remove the old solenoid and install a new one. Before installing a working element, be sure to treat the threads with sealant. It is important. Without this procedure, oil will soon begin to seep through the threads.

4 Why reverse gear does not engage - other reasons

If the described methods for restoring the normal functioning of the gearbox did not help, most likely we encountered problems in the mechanical part of the gearbox:

the spring burst;
the retaining bolt has been cut off;
The device that secures the gearbox elements has broken.

These faults are truly complex. Such problems must be solved by car service specialists, since they will need to remove the gearbox, disassemble it, find the cause of the breakdown, and then fix the problem. All this takes more than one hour and requires the use of special tools. It is irrational to carry out such repairs at home.

Source

A couple of practical tips

Let’s say that when you try to engage reverse gear, the handle does not move completely to the required position. Then under no circumstances should you release the clutch pedal. Perform the switch “through neutral” and save yourself from problems in the future.

Manual transmission in Kalina-2

If, after switching on the gear, a crunching and grinding noise is heard, it means that the handle has not yet been brought to the required point. In this case, there is no need to be afraid that the gears will definitely break. Just follow the previous recommendation and switch again.

One or more gears may shift into gear with a crunch, not clearly, “every once in a while.” In this case, the source of the problem is a faulty clutch assembly. There is no need to delude yourself: if you do not repair or replace it, both the clutch and the gearbox will become unusable.